| IPV6-MIB DEFINITIONS ::= BEGIN |
| |
| IMPORTS |
| MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, |
| mib-2, Counter32, Unsigned32, Integer32, |
| Gauge32 FROM SNMPv2-SMI |
| DisplayString, PhysAddress, TruthValue, TimeStamp, |
| VariablePointer, RowPointer FROM SNMPv2-TC |
| MODULE-COMPLIANCE, OBJECT-GROUP, |
| NOTIFICATION-GROUP FROM SNMPv2-CONF |
| Ipv6IfIndex, Ipv6Address, Ipv6AddressPrefix, |
| Ipv6AddressIfIdentifier, |
| Ipv6IfIndexOrZero FROM IPV6-TC; |
| |
| ipv6MIB MODULE-IDENTITY |
| LAST-UPDATED "9802052155Z" |
| ORGANIZATION "IETF IPv6 Working Group" |
| CONTACT-INFO |
| " Dimitry Haskin |
| |
| Postal: Bay Networks, Inc. |
| 660 Techology Park Drive. |
| Billerica, MA 01821 |
| |
| US |
| |
| Tel: +1-978-916-8124 |
| E-mail: dhaskin@baynetworks.com |
| |
| Steve Onishi |
| |
| Postal: Bay Networks, Inc. |
| 3 Federal Street |
| Billerica, MA 01821 |
| US |
| |
| Tel: +1-978-916-3816 |
| E-mail: sonishi@baynetworks.com" |
| DESCRIPTION |
| "The MIB module for entities implementing the IPv6 |
| protocol." |
| ::= { mib-2 55 } |
| |
| -- the IPv6 general group |
| |
| ipv6MIBObjects OBJECT IDENTIFIER ::= { ipv6MIB 1 } |
| |
| ipv6Forwarding OBJECT-TYPE |
| SYNTAX INTEGER { |
| forwarding(1), -- acting as a router |
| |
| -- NOT acting as |
| notForwarding(2) -- a router |
| } |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The indication of whether this entity is acting |
| as an IPv6 router in respect to the forwarding of |
| datagrams received by, but not addressed to, this |
| entity. IPv6 routers forward datagrams. IPv6 |
| hosts do not (except those source-routed via the |
| host). |
| |
| Note that for some managed nodes, this object may |
| take on only a subset of the values possible. |
| Accordingly, it is appropriate for an agent to |
| return a `wrongValue' response if a management |
| station attempts to change this object to an |
| inappropriate value." |
| ::= { ipv6MIBObjects 1 } |
| |
| ipv6DefaultHopLimit OBJECT-TYPE |
| SYNTAX INTEGER(0..255) |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The default value inserted into the Hop Limit |
| field of the IPv6 header of datagrams originated |
| at this entity, whenever a Hop Limit value is not |
| supplied by the transport layer protocol." |
| DEFVAL { 64 } |
| ::= { ipv6MIBObjects 2 } |
| |
| ipv6Interfaces OBJECT-TYPE |
| SYNTAX Unsigned32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of IPv6 interfaces (regardless of |
| their current state) present on this system." |
| ::= { ipv6MIBObjects 3 } |
| |
| ipv6IfTableLastChange OBJECT-TYPE |
| SYNTAX TimeStamp |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The value of sysUpTime at the time of the last |
| insertion or removal of an entry in the |
| ipv6IfTable. If the number of entries has been |
| unchanged since the last re-initialization of |
| the local network management subsystem, then this |
| object contains a zero value." |
| ::= { ipv6MIBObjects 4 } |
| |
| -- the IPv6 Interfaces table |
| |
| ipv6IfTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF Ipv6IfEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The IPv6 Interfaces table contains information |
| on the entity's internetwork-layer interfaces. |
| An IPv6 interface constitutes a logical network |
| layer attachment to the layer immediately below |
| |
| IPv6 including internet layer 'tunnels', such as |
| tunnels over IPv4 or IPv6 itself." |
| ::= { ipv6MIBObjects 5 } |
| |
| ipv6IfEntry OBJECT-TYPE |
| SYNTAX Ipv6IfEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "An interface entry containing objects |
| about a particular IPv6 interface." |
| INDEX { ipv6IfIndex } |
| ::= { ipv6IfTable 1 } |
| |
| Ipv6IfEntry ::= SEQUENCE { |
| ipv6IfIndex Ipv6IfIndex, |
| ipv6IfDescr DisplayString, |
| ipv6IfLowerLayer VariablePointer, |
| ipv6IfEffectiveMtu Unsigned32, |
| ipv6IfReasmMaxSize Unsigned32, |
| ipv6IfIdentifier Ipv6AddressIfIdentifier, |
| ipv6IfIdentifierLength INTEGER, |
| ipv6IfPhysicalAddress PhysAddress, |
| ipv6IfAdminStatus INTEGER, |
| ipv6IfOperStatus INTEGER, |
| ipv6IfLastChange TimeStamp |
| } |
| |
| ipv6IfIndex OBJECT-TYPE |
| SYNTAX Ipv6IfIndex |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "A unique non-zero value identifying |
| the particular IPv6 interface." |
| ::= { ipv6IfEntry 1 } |
| |
| ipv6IfDescr OBJECT-TYPE |
| SYNTAX DisplayString |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "A textual string containing information about the |
| interface. This string may be set by the network |
| management system." |
| ::= { ipv6IfEntry 2 } |
| |
| ipv6IfLowerLayer OBJECT-TYPE |
| SYNTAX VariablePointer |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "This object identifies the protocol layer over |
| which this network interface operates. If this |
| network interface operates over the data-link |
| layer, then the value of this object refers to an |
| instance of ifIndex [6]. If this network interface |
| operates over an IPv4 interface, the value of this |
| object refers to an instance of ipAdEntAddr [3]. |
| |
| If this network interface operates over another |
| IPv6 interface, the value of this object refers to |
| an instance of ipv6IfIndex. If this network |
| interface is not currently operating over an active |
| protocol layer, then the value of this object |
| should be set to the OBJECT ID { 0 0 }." |
| ::= { ipv6IfEntry 3 } |
| |
| ipv6IfEffectiveMtu OBJECT-TYPE |
| SYNTAX Unsigned32 |
| UNITS "octets" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The size of the largest IPv6 packet which can be |
| sent/received on the interface, specified in |
| octets." |
| ::= { ipv6IfEntry 4 } |
| |
| ipv6IfReasmMaxSize OBJECT-TYPE |
| SYNTAX Unsigned32 (0..65535) |
| UNITS "octets" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The size of the largest IPv6 datagram which this |
| entity can re-assemble from incoming IPv6 fragmented |
| datagrams received on this interface." |
| ::= { ipv6IfEntry 5 } |
| |
| ipv6IfIdentifier OBJECT-TYPE |
| SYNTAX Ipv6AddressIfIdentifier |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The Interface Identifier for this interface that |
| |
| is (at least) unique on the link this interface is |
| attached to. The Interface Identifier is combined |
| with an address prefix to form an interface address. |
| |
| By default, the Interface Identifier is autoconfigured |
| according to the rules of the link type this |
| interface is attached to." |
| ::= { ipv6IfEntry 6 } |
| |
| ipv6IfIdentifierLength OBJECT-TYPE |
| SYNTAX INTEGER (0..64) |
| UNITS "bits" |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The length of the Interface Identifier in bits." |
| ::= { ipv6IfEntry 7 } |
| |
| ipv6IfPhysicalAddress OBJECT-TYPE |
| SYNTAX PhysAddress |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The interface's physical address. For example, for |
| an IPv6 interface attached to an 802.x link, this |
| object normally contains a MAC address. Note that |
| in some cases this address may differ from the |
| address of the interface's protocol sub-layer. The |
| interface's media-specific MIB must define the bit |
| and byte ordering and the format of the value of |
| this object. For interfaces which do not have such |
| an address (e.g., a serial line), this object should |
| contain an octet string of zero length." |
| ::= { ipv6IfEntry 8 } |
| |
| ipv6IfAdminStatus OBJECT-TYPE |
| SYNTAX INTEGER { |
| up(1), -- ready to pass packets |
| down(2) |
| } |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The desired state of the interface. When a managed |
| system initializes, all IPv6 interfaces start with |
| ipv6IfAdminStatus in the down(2) state. As a result |
| of either explicit management action or per |
| configuration information retained by the managed |
| |
| system, ipv6IfAdminStatus is then changed to |
| the up(1) state (or remains in the down(2) state)." |
| ::= { ipv6IfEntry 9 } |
| |
| ipv6IfOperStatus OBJECT-TYPE |
| SYNTAX INTEGER { |
| up(1), -- ready to pass packets |
| |
| down(2), |
| noIfIdentifier(3), -- no interface identifier |
| |
| -- status can not be |
| -- determined for some |
| unknown(4), -- reason |
| |
| -- some component is |
| notPresent(5) -- missing |
| } |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The current operational state of the interface. |
| The noIfIdentifier(3) state indicates that no valid |
| Interface Identifier is assigned to the interface. |
| This state usually indicates that the link-local |
| interface address failed Duplicate Address Detection. |
| If ipv6IfAdminStatus is down(2) then ipv6IfOperStatus |
| should be down(2). If ipv6IfAdminStatus is changed |
| to up(1) then ipv6IfOperStatus should change to up(1) |
| if the interface is ready to transmit and receive |
| network traffic; it should remain in the down(2) or |
| noIfIdentifier(3) state if and only if there is a |
| fault that prevents it from going to the up(1) state; |
| it should remain in the notPresent(5) state if |
| the interface has missing (typically, lower layer) |
| components." |
| ::= { ipv6IfEntry 10 } |
| |
| ipv6IfLastChange OBJECT-TYPE |
| SYNTAX TimeStamp |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The value of sysUpTime at the time the interface |
| entered its current operational state. If the |
| current state was entered prior to the last |
| re-initialization of the local network management |
| |
| subsystem, then this object contains a zero |
| value." |
| ::= { ipv6IfEntry 11 } |
| |
| -- IPv6 Interface Statistics table |
| |
| ipv6IfStatsTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF Ipv6IfStatsEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "IPv6 interface traffic statistics." |
| ::= { ipv6MIBObjects 6 } |
| |
| ipv6IfStatsEntry OBJECT-TYPE |
| SYNTAX Ipv6IfStatsEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "An interface statistics entry containing objects |
| at a particular IPv6 interface." |
| AUGMENTS { ipv6IfEntry } |
| ::= { ipv6IfStatsTable 1 } |
| |
| Ipv6IfStatsEntry ::= SEQUENCE { |
| ipv6IfStatsInReceives |
| Counter32, |
| ipv6IfStatsInHdrErrors |
| Counter32, |
| ipv6IfStatsInTooBigErrors |
| Counter32, |
| ipv6IfStatsInNoRoutes |
| Counter32, |
| ipv6IfStatsInAddrErrors |
| Counter32, |
| ipv6IfStatsInUnknownProtos |
| Counter32, |
| ipv6IfStatsInTruncatedPkts |
| Counter32, |
| ipv6IfStatsInDiscards |
| Counter32, |
| ipv6IfStatsInDelivers |
| Counter32, |
| ipv6IfStatsOutForwDatagrams |
| Counter32, |
| ipv6IfStatsOutRequests |
| Counter32, |
| ipv6IfStatsOutDiscards |
| |
| Counter32, |
| ipv6IfStatsOutFragOKs |
| Counter32, |
| ipv6IfStatsOutFragFails |
| Counter32, |
| ipv6IfStatsOutFragCreates |
| Counter32, |
| ipv6IfStatsReasmReqds |
| Counter32, |
| ipv6IfStatsReasmOKs |
| Counter32, |
| ipv6IfStatsReasmFails |
| Counter32, |
| ipv6IfStatsInMcastPkts |
| Counter32, |
| ipv6IfStatsOutMcastPkts |
| Counter32 |
| } |
| |
| ipv6IfStatsInReceives OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The total number of input datagrams received by |
| the interface, including those received in error." |
| ::= { ipv6IfStatsEntry 1 } |
| |
| ipv6IfStatsInHdrErrors OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of input datagrams discarded due to |
| errors in their IPv6 headers, including version |
| number mismatch, other format errors, hop count |
| exceeded, errors discovered in processing their |
| IPv6 options, etc." |
| ::= { ipv6IfStatsEntry 2 } |
| |
| ipv6IfStatsInTooBigErrors OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of input datagrams that could not be |
| forwarded because their size exceeded the link MTU |
| of outgoing interface." |
| ::= { ipv6IfStatsEntry 3 } |
| |
| ipv6IfStatsInNoRoutes OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of input datagrams discarded because no |
| route could be found to transmit them to their |
| destination." |
| ::= { ipv6IfStatsEntry 4 } |
| |
| ipv6IfStatsInAddrErrors OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of input datagrams discarded because |
| the IPv6 address in their IPv6 header's destination |
| field was not a valid address to be received at |
| this entity. This count includes invalid |
| addresses (e.g., ::0) and unsupported addresses |
| (e.g., addresses with unallocated prefixes). For |
| entities which are not IPv6 routers and therefore |
| do not forward datagrams, this counter includes |
| datagrams discarded because the destination address |
| was not a local address." |
| ::= { ipv6IfStatsEntry 5 } |
| |
| ipv6IfStatsInUnknownProtos OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of locally-addressed datagrams |
| received successfully but discarded because of an |
| unknown or unsupported protocol. This counter is |
| incremented at the interface to which these |
| datagrams were addressed which might not be |
| necessarily the input interface for some of |
| the datagrams." |
| ::= { ipv6IfStatsEntry 6 } |
| |
| ipv6IfStatsInTruncatedPkts OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of input datagrams discarded because |
| datagram frame didn't carry enough data." |
| ::= { ipv6IfStatsEntry 7 } |
| |
| ipv6IfStatsInDiscards OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of input IPv6 datagrams for which no |
| problems were encountered to prevent their |
| continued processing, but which were discarded |
| (e.g., for lack of buffer space). Note that this |
| counter does not include any datagrams discarded |
| while awaiting re-assembly." |
| ::= { ipv6IfStatsEntry 8 } |
| |
| ipv6IfStatsInDelivers OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The total number of datagrams successfully |
| delivered to IPv6 user-protocols (including ICMP). |
| This counter is incremented at the interface to |
| which these datagrams were addressed which might |
| not be necessarily the input interface for some of |
| the datagrams." |
| ::= { ipv6IfStatsEntry 9 } |
| |
| ipv6IfStatsOutForwDatagrams OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of output datagrams which this |
| entity received and forwarded to their final |
| destinations. In entities which do not act |
| as IPv6 routers, this counter will include |
| only those packets which were Source-Routed |
| via this entity, and the Source-Route |
| processing was successful. Note that for |
| a successfully forwarded datagram the counter |
| of the outgoing interface is incremented." |
| ::= { ipv6IfStatsEntry 10 } |
| |
| ipv6IfStatsOutRequests OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The total number of IPv6 datagrams which local IPv6 |
| user-protocols (including ICMP) supplied to IPv6 in |
| requests for transmission. Note that this counter |
| does not include any datagrams counted in |
| ipv6IfStatsOutForwDatagrams." |
| ::= { ipv6IfStatsEntry 11 } |
| |
| ipv6IfStatsOutDiscards OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of output IPv6 datagrams for which no |
| problem was encountered to prevent their |
| transmission to their destination, but which were |
| discarded (e.g., for lack of buffer space). Note |
| that this counter would include datagrams counted |
| in ipv6IfStatsOutForwDatagrams if any such packets |
| met this (discretionary) discard criterion." |
| ::= { ipv6IfStatsEntry 12 } |
| |
| ipv6IfStatsOutFragOKs OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of IPv6 datagrams that have been |
| successfully fragmented at this output interface." |
| ::= { ipv6IfStatsEntry 13 } |
| |
| ipv6IfStatsOutFragFails OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of IPv6 datagrams that have been |
| discarded because they needed to be fragmented |
| at this output interface but could not be." |
| ::= { ipv6IfStatsEntry 14 } |
| |
| ipv6IfStatsOutFragCreates OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of output datagram fragments that have |
| been generated as a result of fragmentation at |
| this output interface." |
| ::= { ipv6IfStatsEntry 15 } |
| |
| ipv6IfStatsReasmReqds OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of IPv6 fragments received which needed |
| to be reassembled at this interface. Note that this |
| counter is incremented at the interface to which |
| these fragments were addressed which might not |
| be necessarily the input interface for some of |
| the fragments." |
| ::= { ipv6IfStatsEntry 16 } |
| |
| ipv6IfStatsReasmOKs OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of IPv6 datagrams successfully |
| reassembled. Note that this counter is incremented |
| at the interface to which these datagrams were |
| addressed which might not be necessarily the input |
| interface for some of the fragments." |
| ::= { ipv6IfStatsEntry 17 } |
| |
| ipv6IfStatsReasmFails OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of failures detected by the IPv6 re- |
| assembly algorithm (for whatever reason: timed |
| out, errors, etc.). Note that this is not |
| necessarily a count of discarded IPv6 fragments |
| since some algorithms (notably the algorithm in |
| RFC 815) can lose track of the number of fragments |
| by combining them as they are received. |
| This counter is incremented at the interface to which |
| these fragments were addressed which might not be |
| necessarily the input interface for some of the |
| fragments." |
| ::= { ipv6IfStatsEntry 18 } |
| |
| ipv6IfStatsInMcastPkts OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of multicast packets received |
| by the interface" |
| ::= { ipv6IfStatsEntry 19 } |
| |
| ipv6IfStatsOutMcastPkts OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of multicast packets transmitted |
| by the interface" |
| ::= { ipv6IfStatsEntry 20 } |
| |
| -- Address Prefix table |
| |
| -- The IPv6 Address Prefix table contains information on |
| -- the entity's IPv6 Address Prefixes that are associated |
| -- with IPv6 interfaces. |
| |
| ipv6AddrPrefixTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF Ipv6AddrPrefixEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The list of IPv6 address prefixes of |
| IPv6 interfaces." |
| ::= { ipv6MIBObjects 7 } |
| |
| ipv6AddrPrefixEntry OBJECT-TYPE |
| SYNTAX Ipv6AddrPrefixEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "An interface entry containing objects of |
| a particular IPv6 address prefix." |
| INDEX { ipv6IfIndex, |
| ipv6AddrPrefix, |
| ipv6AddrPrefixLength } |
| ::= { ipv6AddrPrefixTable 1 } |
| |
| Ipv6AddrPrefixEntry ::= SEQUENCE { |
| |
| ipv6AddrPrefix Ipv6AddressPrefix, |
| ipv6AddrPrefixLength INTEGER (0..128), |
| ipv6AddrPrefixOnLinkFlag TruthValue, |
| ipv6AddrPrefixAutonomousFlag TruthValue, |
| ipv6AddrPrefixAdvPreferredLifetime Unsigned32, |
| ipv6AddrPrefixAdvValidLifetime Unsigned32 |
| } |
| |
| ipv6AddrPrefix OBJECT-TYPE |
| SYNTAX Ipv6AddressPrefix |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The prefix associated with the this interface." |
| ::= { ipv6AddrPrefixEntry 1 } |
| |
| ipv6AddrPrefixLength OBJECT-TYPE |
| SYNTAX INTEGER (0..128) |
| UNITS "bits" |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The length of the prefix (in bits)." |
| ::= { ipv6AddrPrefixEntry 2 } |
| |
| ipv6AddrPrefixOnLinkFlag OBJECT-TYPE |
| SYNTAX TruthValue |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "This object has the value 'true(1)', if this |
| prefix can be used for on-link determination |
| and the value 'false(2)' otherwise." |
| ::= { ipv6AddrPrefixEntry 3 } |
| |
| ipv6AddrPrefixAutonomousFlag OBJECT-TYPE |
| SYNTAX TruthValue |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "Autonomous address configuration flag. When |
| true(1), indicates that this prefix can be used |
| for autonomous address configuration (i.e. can |
| be used to form a local interface address). |
| If false(2), it is not used to autoconfigure |
| a local interface address." |
| ::= { ipv6AddrPrefixEntry 4 } |
| |
| ipv6AddrPrefixAdvPreferredLifetime OBJECT-TYPE |
| SYNTAX Unsigned32 |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "It is the length of time in seconds that this |
| prefix will remain preferred, i.e. time until |
| deprecation. A value of 4,294,967,295 represents |
| infinity. |
| |
| The address generated from a deprecated prefix |
| should no longer be used as a source address in |
| new communications, but packets received on such |
| an interface are processed as expected." |
| ::= { ipv6AddrPrefixEntry 5 } |
| |
| ipv6AddrPrefixAdvValidLifetime OBJECT-TYPE |
| SYNTAX Unsigned32 |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "It is the length of time in seconds that this |
| prefix will remain valid, i.e. time until |
| invalidation. A value of 4,294,967,295 represents |
| infinity. |
| |
| The address generated from an invalidated prefix |
| should not appear as the destination or source |
| address of a packet." |
| ::= { ipv6AddrPrefixEntry 6 } |
| |
| -- the IPv6 Address table |
| |
| -- The IPv6 address table contains this node's IPv6 |
| -- addressing information. |
| |
| ipv6AddrTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF Ipv6AddrEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The table of addressing information relevant to |
| this node's interface addresses." |
| ::= { ipv6MIBObjects 8 } |
| |
| ipv6AddrEntry OBJECT-TYPE |
| SYNTAX Ipv6AddrEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The addressing information for one of this |
| node's interface addresses." |
| INDEX { ipv6IfIndex, ipv6AddrAddress } |
| ::= { ipv6AddrTable 1 } |
| |
| Ipv6AddrEntry ::= |
| SEQUENCE { |
| ipv6AddrAddress Ipv6Address, |
| ipv6AddrPfxLength INTEGER, |
| ipv6AddrType INTEGER, |
| ipv6AddrAnycastFlag TruthValue, |
| ipv6AddrStatus INTEGER |
| } |
| |
| ipv6AddrAddress OBJECT-TYPE |
| SYNTAX Ipv6Address |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The IPv6 address to which this entry's addressing |
| information pertains." |
| ::= { ipv6AddrEntry 1 } |
| |
| ipv6AddrPfxLength OBJECT-TYPE |
| SYNTAX INTEGER(0..128) |
| UNITS "bits" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The length of the prefix (in bits) associated with |
| the IPv6 address of this entry." |
| ::= { ipv6AddrEntry 2 } |
| |
| ipv6AddrType OBJECT-TYPE |
| SYNTAX INTEGER { |
| -- address has been formed |
| -- using stateless |
| stateless(1), -- autoconfiguration |
| |
| -- address has been acquired |
| -- by stateful means |
| -- (e.g. DHCPv6, manual |
| stateful(2), -- configuration) |
| |
| -- type can not be determined |
| unknown(3) -- for some reason. |
| } |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The type of address. Note that 'stateless(1)' |
| refers to an address that was statelessly |
| autoconfigured; 'stateful(2)' refers to a address |
| which was acquired by via a stateful protocol |
| (e.g. DHCPv6, manual configuration)." |
| ::= { ipv6AddrEntry 3 } |
| |
| ipv6AddrAnycastFlag OBJECT-TYPE |
| SYNTAX TruthValue |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "This object has the value 'true(1)', if this |
| address is an anycast address and the value |
| 'false(2)' otherwise." |
| ::= { ipv6AddrEntry 4 } |
| |
| ipv6AddrStatus OBJECT-TYPE |
| SYNTAX INTEGER { |
| preferred(1), |
| deprecated(2), |
| invalid(3), |
| inaccessible(4), |
| unknown(5) -- status can not be determined |
| -- for some reason. |
| } |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "Address status. The preferred(1) state indicates |
| that this is a valid address that can appear as |
| the destination or source address of a packet. |
| The deprecated(2) state indicates that this is |
| a valid but deprecated address that should no longer |
| be used as a source address in new communications, |
| but packets addressed to such an address are |
| processed as expected. The invalid(3) state indicates |
| that this is not valid address which should not |
| |
| appear as the destination or source address of |
| a packet. The inaccessible(4) state indicates that |
| the address is not accessible because the interface |
| to which this address is assigned is not operational." |
| ::= { ipv6AddrEntry 5 } |
| |
| -- IPv6 Routing objects |
| |
| ipv6RouteNumber OBJECT-TYPE |
| SYNTAX Gauge32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of current ipv6RouteTable entries. |
| This is primarily to avoid having to read |
| the table in order to determine this number." |
| ::= { ipv6MIBObjects 9 } |
| |
| ipv6DiscardedRoutes OBJECT-TYPE |
| SYNTAX Counter32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of routing entries which were chosen |
| to be discarded even though they are valid. One |
| possible reason for discarding such an entry could |
| be to free-up buffer space for other routing |
| entries." |
| ::= { ipv6MIBObjects 10 } |
| |
| -- IPv6 Routing table |
| |
| ipv6RouteTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF Ipv6RouteEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "IPv6 Routing table. This table contains |
| an entry for each valid IPv6 unicast route |
| that can be used for packet forwarding |
| determination." |
| ::= { ipv6MIBObjects 11 } |
| |
| ipv6RouteEntry OBJECT-TYPE |
| SYNTAX Ipv6RouteEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "A routing entry." |
| INDEX { ipv6RouteDest, |
| ipv6RoutePfxLength, |
| ipv6RouteIndex } |
| ::= { ipv6RouteTable 1 } |
| |
| Ipv6RouteEntry ::= SEQUENCE { |
| ipv6RouteDest Ipv6Address, |
| ipv6RoutePfxLength INTEGER, |
| ipv6RouteIndex Unsigned32, |
| ipv6RouteIfIndex Ipv6IfIndexOrZero, |
| ipv6RouteNextHop Ipv6Address, |
| ipv6RouteType INTEGER, |
| ipv6RouteProtocol INTEGER, |
| ipv6RoutePolicy Integer32, |
| ipv6RouteAge Unsigned32, |
| ipv6RouteNextHopRDI Unsigned32, |
| ipv6RouteMetric Unsigned32, |
| ipv6RouteWeight Unsigned32, |
| ipv6RouteInfo RowPointer, |
| ipv6RouteValid TruthValue |
| } |
| |
| ipv6RouteDest OBJECT-TYPE |
| SYNTAX Ipv6Address |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The destination IPv6 address of this route. |
| This object may not take a Multicast address |
| value." |
| ::= { ipv6RouteEntry 1 } |
| |
| ipv6RoutePfxLength OBJECT-TYPE |
| SYNTAX INTEGER(0..128) |
| UNITS "bits" |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "Indicates the prefix length of the destination |
| address." |
| ::= { ipv6RouteEntry 2 } |
| |
| ipv6RouteIndex OBJECT-TYPE |
| SYNTAX Unsigned32 |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The value which uniquely identifies the route |
| among the routes to the same network layer |
| destination. The way this value is chosen is |
| implementation specific but it must be unique for |
| ipv6RouteDest/ipv6RoutePfxLength pair and remain |
| constant for the life of the route." |
| ::= { ipv6RouteEntry 3 } |
| |
| ipv6RouteIfIndex OBJECT-TYPE |
| SYNTAX Ipv6IfIndexOrZero |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The index value which uniquely identifies the local |
| interface through which the next hop of this |
| route should be reached. The interface identified |
| by a particular value of this index is the same |
| interface as identified by the same value of |
| ipv6IfIndex. For routes of the discard type this |
| value can be zero." |
| ::= { ipv6RouteEntry 4 } |
| |
| ipv6RouteNextHop OBJECT-TYPE |
| SYNTAX Ipv6Address |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "On remote routes, the address of the next |
| system en route; otherwise, ::0 |
| ('00000000000000000000000000000000'H in ASN.1 |
| string representation)." |
| ::= { ipv6RouteEntry 5 } |
| |
| ipv6RouteType OBJECT-TYPE |
| SYNTAX INTEGER { |
| other(1), -- none of the following |
| |
| -- an route indicating that |
| -- packets to destinations |
| -- matching this route are |
| discard(2), -- to be discarded |
| |
| -- route to directly |
| local(3), -- connected (sub-)network |
| |
| -- route to a remote |
| |
| remote(4) -- destination |
| |
| } |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The type of route. Note that 'local(3)' refers |
| to a route for which the next hop is the final |
| destination; 'remote(4)' refers to a route for |
| which the next hop is not the final |
| destination; 'discard(2)' refers to a route |
| indicating that packets to destinations matching |
| this route are to be discarded (sometimes called |
| black-hole route)." |
| ::= { ipv6RouteEntry 6 } |
| |
| ipv6RouteProtocol OBJECT-TYPE |
| SYNTAX INTEGER { |
| other(1), -- none of the following |
| |
| -- non-protocol information, |
| -- e.g., manually configured |
| local(2), -- entries |
| |
| netmgmt(3), -- static route |
| |
| -- obtained via Neighbor |
| -- Discovery protocol, |
| ndisc(4), -- e.g., result of Redirect |
| |
| -- the following are all |
| -- dynamic routing protocols |
| rip(5), -- RIPng |
| ospf(6), -- Open Shortest Path First |
| bgp(7), -- Border Gateway Protocol |
| idrp(8), -- InterDomain Routing Protocol |
| igrp(9) -- InterGateway Routing Protocol |
| } |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The routing mechanism via which this route was |
| learned." |
| ::= { ipv6RouteEntry 7 } |
| |
| ipv6RoutePolicy OBJECT-TYPE |
| SYNTAX Integer32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The general set of conditions that would cause the |
| selection of one multipath route (set of next hops |
| for a given destination) is referred to as 'policy'. |
| Unless the mechanism indicated by ipv6RouteProtocol |
| specified otherwise, the policy specifier is the |
| 8-bit Traffic Class field of the IPv6 packet header |
| that is zero extended at the left to a 32-bit value. |
| |
| Protocols defining 'policy' otherwise must either |
| define a set of values which are valid for |
| this object or must implement an integer- |
| instanced policy table for which this object's |
| value acts as an index." |
| ::= { ipv6RouteEntry 8 } |
| |
| ipv6RouteAge OBJECT-TYPE |
| SYNTAX Unsigned32 |
| UNITS "seconds" |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The number of seconds since this route was last |
| updated or otherwise determined to be correct. |
| Note that no semantics of `too old' can be implied |
| except through knowledge of the routing protocol |
| by which the route was learned." |
| ::= { ipv6RouteEntry 9 } |
| |
| ipv6RouteNextHopRDI OBJECT-TYPE |
| SYNTAX Unsigned32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The Routing Domain ID of the Next Hop. |
| The semantics of this object are determined by |
| the routing-protocol specified in the route's |
| ipv6RouteProtocol value. When this object is |
| unknown or not relevant its value should be set |
| to zero." |
| ::= { ipv6RouteEntry 10 } |
| |
| ipv6RouteMetric OBJECT-TYPE |
| SYNTAX Unsigned32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The routing metric for this route. The |
| semantics of this metric are determined by the |
| routing protocol specified in the route's |
| ipv6RouteProtocol value. When this is unknown |
| or not relevant to the protocol indicated by |
| ipv6RouteProtocol, the object value should be |
| set to its maximum value (4,294,967,295)." |
| ::= { ipv6RouteEntry 11 } |
| |
| ipv6RouteWeight OBJECT-TYPE |
| SYNTAX Unsigned32 |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The system internal weight value for this route. |
| The semantics of this value are determined by |
| the implementation specific rules. Generally, |
| within routes with the same ipv6RoutePolicy value, |
| the lower the weight value the more preferred is |
| the route." |
| ::= { ipv6RouteEntry 12 } |
| |
| ipv6RouteInfo OBJECT-TYPE |
| SYNTAX RowPointer |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "A reference to MIB definitions specific to the |
| particular routing protocol which is responsible |
| for this route, as determined by the value |
| specified in the route's ipv6RouteProto value. |
| If this information is not present, its value |
| should be set to the OBJECT ID { 0 0 }, |
| which is a syntactically valid object identifier, |
| and any implementation conforming to ASN.1 |
| and the Basic Encoding Rules must be able to |
| generate and recognize this value." |
| ::= { ipv6RouteEntry 13 } |
| |
| ipv6RouteValid OBJECT-TYPE |
| SYNTAX TruthValue |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "Setting this object to the value 'false(2)' has |
| the effect of invalidating the corresponding entry |
| in the ipv6RouteTable object. That is, it |
| effectively disassociates the destination |
| |
| identified with said entry from the route |
| identified with said entry. It is an |
| implementation-specific matter as to whether the |
| agent removes an invalidated entry from the table. |
| Accordingly, management stations must be prepared |
| to receive tabular information from agents that |
| corresponds to entries not currently in use. |
| Proper interpretation of such entries requires |
| examination of the relevant ipv6RouteValid |
| object." |
| DEFVAL { true } |
| ::= { ipv6RouteEntry 14 } |
| |
| -- IPv6 Address Translation table |
| |
| ipv6NetToMediaTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF Ipv6NetToMediaEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The IPv6 Address Translation table used for |
| mapping from IPv6 addresses to physical addresses. |
| |
| The IPv6 address translation table contain the |
| Ipv6Address to `physical' address equivalencies. |
| Some interfaces do not use translation tables |
| for determining address equivalencies; if all |
| interfaces are of this type, then the Address |
| Translation table is empty, i.e., has zero |
| entries." |
| ::= { ipv6MIBObjects 12 } |
| |
| ipv6NetToMediaEntry OBJECT-TYPE |
| SYNTAX Ipv6NetToMediaEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "Each entry contains one IPv6 address to `physical' |
| address equivalence." |
| INDEX { ipv6IfIndex, |
| ipv6NetToMediaNetAddress } |
| ::= { ipv6NetToMediaTable 1 } |
| |
| Ipv6NetToMediaEntry ::= SEQUENCE { |
| ipv6NetToMediaNetAddress |
| Ipv6Address, |
| ipv6NetToMediaPhysAddress |
| |
| PhysAddress, |
| ipv6NetToMediaType |
| INTEGER, |
| ipv6IfNetToMediaState |
| INTEGER, |
| ipv6IfNetToMediaLastUpdated |
| TimeStamp, |
| ipv6NetToMediaValid |
| TruthValue |
| } |
| |
| ipv6NetToMediaNetAddress OBJECT-TYPE |
| SYNTAX Ipv6Address |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The IPv6 Address corresponding to |
| the media-dependent `physical' address." |
| ::= { ipv6NetToMediaEntry 1 } |
| |
| ipv6NetToMediaPhysAddress OBJECT-TYPE |
| SYNTAX PhysAddress |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The media-dependent `physical' address." |
| ::= { ipv6NetToMediaEntry 2 } |
| |
| ipv6NetToMediaType OBJECT-TYPE |
| SYNTAX INTEGER { |
| other(1), -- none of the following |
| dynamic(2), -- dynamically resolved |
| static(3), -- statically configured |
| local(4) -- local interface |
| } |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The type of the mapping. The 'dynamic(2)' type |
| indicates that the IPv6 address to physical |
| addresses mapping has been dynamically |
| resolved using the IPv6 Neighbor Discovery |
| protocol. The static(3)' types indicates that |
| the mapping has been statically configured. |
| The local(4) indicates that the mapping is |
| provided for an entity's own interface address." |
| ::= { ipv6NetToMediaEntry 3 } |
| |
| ipv6IfNetToMediaState OBJECT-TYPE |
| SYNTAX INTEGER { |
| reachable(1), -- confirmed reachability |
| |
| stale(2), -- unconfirmed reachability |
| |
| delay(3), -- waiting for reachability |
| -- confirmation before entering |
| -- the probe state |
| |
| probe(4), -- actively probing |
| |
| invalid(5), -- an invalidated mapping |
| |
| unknown(6) -- state can not be determined |
| -- for some reason. |
| } |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The Neighbor Unreachability Detection [8] state |
| for the interface when the address mapping in |
| this entry is used." |
| ::= { ipv6NetToMediaEntry 4 } |
| |
| ipv6IfNetToMediaLastUpdated OBJECT-TYPE |
| SYNTAX TimeStamp |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The value of sysUpTime at the time this entry |
| was last updated. If this entry was updated prior |
| to the last re-initialization of the local network |
| management subsystem, then this object contains |
| a zero value." |
| ::= { ipv6NetToMediaEntry 5 } |
| |
| ipv6NetToMediaValid OBJECT-TYPE |
| SYNTAX TruthValue |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "Setting this object to the value 'false(2)' has |
| the effect of invalidating the corresponding entry |
| in the ipv6NetToMediaTable. That is, it effectively |
| disassociates the interface identified with said |
| entry from the mapping identified with said entry. |
| It is an implementation-specific matter as to |
| |
| whether the agent removes an invalidated entry |
| from the table. Accordingly, management stations |
| must be prepared to receive tabular information |
| from agents that corresponds to entries not |
| currently in use. Proper interpretation of such |
| entries requires examination of the relevant |
| ipv6NetToMediaValid object." |
| DEFVAL { true } |
| ::= { ipv6NetToMediaEntry 6 } |
| |
| -- definition of IPv6-related notifications. |
| -- Note that we need ipv6NotificationPrefix with the 0 |
| -- sub-identifier to make this MIB to translate to |
| -- an SNMPv1 format in a reversible way. For example |
| -- it is needed for proxies that convert SNMPv1 traps |
| -- to SNMPv2 notifications without MIB knowledge. |
| |
| ipv6Notifications OBJECT IDENTIFIER |
| ::= { ipv6MIB 2 } |
| ipv6NotificationPrefix OBJECT IDENTIFIER |
| ::= { ipv6Notifications 0 } |
| |
| ipv6IfStateChange NOTIFICATION-TYPE |
| OBJECTS { |
| ipv6IfDescr, |
| ipv6IfOperStatus -- the new state of the If. |
| } |
| STATUS current |
| DESCRIPTION |
| "An ipv6IfStateChange notification signifies |
| that there has been a change in the state of |
| an ipv6 interface. This notification should |
| be generated when the interface's operational |
| status transitions to or from the up(1) state." |
| ::= { ipv6NotificationPrefix 1 } |
| |
| -- conformance information |
| |
| ipv6Conformance OBJECT IDENTIFIER ::= { ipv6MIB 3 } |
| |
| ipv6Compliances OBJECT IDENTIFIER ::= { ipv6Conformance 1 } |
| ipv6Groups OBJECT IDENTIFIER ::= { ipv6Conformance 2 } |
| |
| -- compliance statements |
| |
| ipv6Compliance MODULE-COMPLIANCE |
| STATUS current |
| DESCRIPTION |
| "The compliance statement for SNMPv2 entities which |
| implement ipv6 MIB." |
| MODULE -- this module |
| MANDATORY-GROUPS { ipv6GeneralGroup, |
| ipv6NotificationGroup } |
| OBJECT ipv6Forwarding |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "An agent is not required to provide write |
| access to this object" |
| OBJECT ipv6DefaultHopLimit |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "An agent is not required to provide write |
| access to this object" |
| OBJECT ipv6IfDescr |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "An agent is not required to provide write |
| access to this object" |
| OBJECT ipv6IfIdentifier |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "An agent is not required to provide write |
| access to this object" |
| OBJECT ipv6IfIdentifierLength |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "An agent is not required to provide write |
| access to this object" |
| |
| OBJECT ipv6IfAdminStatus |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "An agent is not required to provide write |
| access to this object" |
| OBJECT ipv6RouteValid |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "An agent is not required to provide write |
| access to this object" |
| OBJECT ipv6NetToMediaValid |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "An agent is not required to provide write |
| |
| access to this object" |
| ::= { ipv6Compliances 1 } |
| |
| ipv6GeneralGroup OBJECT-GROUP |
| OBJECTS { ipv6Forwarding, |
| ipv6DefaultHopLimit, |
| ipv6Interfaces, |
| ipv6IfTableLastChange, |
| ipv6IfDescr, |
| ipv6IfLowerLayer, |
| ipv6IfEffectiveMtu, |
| ipv6IfReasmMaxSize, |
| ipv6IfIdentifier, |
| ipv6IfIdentifierLength, |
| ipv6IfPhysicalAddress, |
| ipv6IfAdminStatus, |
| ipv6IfOperStatus, |
| ipv6IfLastChange, |
| ipv6IfStatsInReceives, |
| ipv6IfStatsInHdrErrors, |
| ipv6IfStatsInTooBigErrors, |
| ipv6IfStatsInNoRoutes, |
| ipv6IfStatsInAddrErrors, |
| ipv6IfStatsInUnknownProtos, |
| ipv6IfStatsInTruncatedPkts, |
| ipv6IfStatsInDiscards, |
| ipv6IfStatsInDelivers, |
| ipv6IfStatsOutForwDatagrams, |
| ipv6IfStatsOutRequests, |
| ipv6IfStatsOutDiscards, |
| ipv6IfStatsOutFragOKs, |
| ipv6IfStatsOutFragFails, |
| ipv6IfStatsOutFragCreates, |
| ipv6IfStatsReasmReqds, |
| ipv6IfStatsReasmOKs, |
| ipv6IfStatsReasmFails, |
| ipv6IfStatsInMcastPkts, |
| ipv6IfStatsOutMcastPkts, |
| ipv6AddrPrefixOnLinkFlag, |
| ipv6AddrPrefixAutonomousFlag, |
| ipv6AddrPrefixAdvPreferredLifetime, |
| ipv6AddrPrefixAdvValidLifetime, |
| ipv6AddrPfxLength, |
| ipv6AddrType, |
| ipv6AddrAnycastFlag, |
| ipv6AddrStatus, |
| ipv6RouteNumber, |
| ipv6DiscardedRoutes, |
| ipv6RouteIfIndex, |
| ipv6RouteNextHop, |
| ipv6RouteType, |
| ipv6RouteProtocol, |
| ipv6RoutePolicy, |
| ipv6RouteAge, |
| ipv6RouteNextHopRDI, |
| ipv6RouteMetric, |
| ipv6RouteWeight, |
| ipv6RouteInfo, |
| ipv6RouteValid, |
| ipv6NetToMediaPhysAddress, |
| ipv6NetToMediaType, |
| ipv6IfNetToMediaState, |
| ipv6IfNetToMediaLastUpdated, |
| ipv6NetToMediaValid } |
| STATUS current |
| DESCRIPTION |
| "The IPv6 group of objects providing for basic |
| management of IPv6 entities." |
| ::= { ipv6Groups 1 } |
| |
| ipv6NotificationGroup NOTIFICATION-GROUP |
| NOTIFICATIONS { ipv6IfStateChange } |
| STATUS current |
| DESCRIPTION |
| "The notification that an IPv6 entity is required |
| to implement." |
| ::= { ipv6Groups 2 } |
| |
| END |
