blob: 315b8f8296ae5d3c329cb2bbc8dc7d007ae48f09 [file] [log] [blame]
#ifdef BROADCOM
#define _POSIX_C_SOURCE 199309L /* for clock_gettime */
#define _BSD_SOURCE /* for usleep */
#include <features.h>
#include <assert.h>
#include <fcntl.h>
#include <signal.h>
#include <stdio.h>
#include <stdlib.h>
#include <stdint.h>
#include <string.h>
#include <sys/select.h>
#include <sys/time.h>
#include <sys/uio.h>
#include <sys/wait.h>
#include <sys/mman.h>
#include <time.h>
#include <unistd.h>
#include <stacktrace.h>
#include "pin.h"
#define UNUSED __attribute__((unused))
#define DEVMEM "/dev/mem"
struct PinHandle_s {
int unused;
};
#define CHECK(x) do { \
int rv = (x); \
if (rv) { \
fprintf(stderr, "CHECK: %s returned %d\n", #x, rv); \
_exit(99); \
} \
} while (0)
static volatile void* mmap_addr = MAP_FAILED;
static size_t mmap_size = 0;
static int mmap_fd = -1;
struct Gpio {
int is_present;
unsigned int pinmux_offset;
unsigned int pinmux_mask;
unsigned int pinmux_value;
unsigned int offset_direction;
unsigned int offset_data;
/* for offset_direction and offset_data */
unsigned int mask; // eg, (*reg & mask) >> shift == on_value
unsigned int shift;
unsigned int off_value;
unsigned int on_value;
unsigned int direction_value; // 0 is output
int old_val;
};
struct Fan {
int is_present;
int open_drain;
unsigned int offset_data;
unsigned int channel;
int old_percent;
};
struct Temp {
int is_present;
unsigned int offset_data;
double (*get_temp)(struct Temp* t);
};
struct Voltage {
int is_present;
unsigned int offset_data;
double (*get_voltage)(struct Voltage* v);
};
struct platform_info {
const char *name;
off_t mmap_base;
size_t mmap_size;
void (*init)(struct platform_info* p);
struct Gpio led_red;
struct Gpio led_blue;
struct Gpio led_activity;
struct Gpio led_standby;
struct Gpio reset_button;
struct Gpio fan_tick;
struct Fan fan_control;
struct Temp temp_monitor;
struct Voltage voltage_monitor;
};
static void init_gfhd200(struct platform_info* p);
static void init_gfhd254(struct platform_info* p);
static double get_avs_temperature_74xx(struct Temp* t);
static double get_avs_temperature_7252(struct Temp* t);
static double get_avs_voltage_74xx(struct Voltage* v);
static double get_avs_voltage_7252(struct Voltage* v);
struct platform_info platforms[] = {
{
.name = "GFHD100",
.mmap_base = 0x10400000, // base of many brcm registers
.mmap_size = 0x40000,
.led_red = {
.is_present = 1, // GPIO 17
.offset_direction = 0x94c8, // GIO_AON_IODIR_LO
.offset_data = 0x94c4, // GIO_AON_DATA_LO
.mask = 0x00020000, // 1<<17
.shift = 17,
.off_value = 0,
.on_value = 1,
.direction_value = 0,
.old_val = -1,
},
.led_blue = {
.is_present = 1, // GPIO 12
.offset_direction = 0x94c8, // GIO_AON_IODIR_LO
.offset_data = 0x94c4, // GIO_AON_DATA_LO
.mask = 0x00001000, // 1<<12
.shift = 12,
.off_value = 0,
.on_value = 1,
.direction_value = 0,
.old_val = -1,
},
.led_activity = {
.is_present = 1, // GPIO 13
.offset_direction = 0x94c8, // GIO_AON_IODIR_LO
.offset_data = 0x94c4, // GIO_AON_DATA_LO
.mask = 0x00002000, // 1<<13
.shift = 13,
.off_value = 0,
.on_value = 1,
.direction_value = 0,
.old_val = -1,
},
.led_standby = {
.is_present = 1, // GPIO 10
.offset_direction = 0x94c8, // GIO_AON_IODIR_LO
.offset_data = 0x94c4, // GIO_AON_DATA_LO
.mask = 0x00000400, // 1<<10
.shift = 10,
.off_value = 0,
.on_value = 1,
.direction_value = 0,
.old_val = -1,
},
.reset_button = {
.is_present = 1, // GPIO 4
.offset_direction = 0x94c8, // GIO_AON_IODIR_LO
.offset_data = 0x94c4, // GIO_AON_DATA_LO
.mask = 0x00000010, // 1<<4
.shift = 4,
.off_value = 0,
.on_value = 1,
.direction_value = 1,
.old_val = -1,
},
.fan_tick = {
.is_present = 1, // GPIO 98
.offset_direction = 0x6768, // GIO_IODIR_EXT_HI
.offset_data = 0x6764, // GIO_DATA_EXT_HI
.mask = 0x00000100, // 1<<8
.shift = 8,
.off_value = 0,
.on_value = 1,
.direction_value = 1,
.old_val = -1,
},
.fan_control = {
.is_present = 1, // PWM 1
.offset_data = 0x6580, // PWM_CTRL ...
.channel = 0,
.open_drain = 1,
},
.temp_monitor = {
.is_present = 1, // 7425 AVS_RO_REGISTERS_0
.offset_data = 0x32b00, // BCHP_AVS_RO_REGISTERS_0_PVT_TEMPERATURE_MNTR_STATUS
.get_temp = get_avs_temperature_74xx,
},
.voltage_monitor = {
.is_present = 1, // 7425 AVS_RO_REGISTERS_0
.offset_data = 0x32b0c, // BCHP_AVS_RO_REGISTERS_0_PVT_1P10V_0_MNTR_STATUS
.get_voltage = get_avs_voltage_74xx,
},
},
{
.name = "GFMS100",
.mmap_base = 0x10400000, // base of many brcm registers
.mmap_size = 0x40000,
.led_red = {
.is_present = 1, // GPIO 17
.offset_direction = 0x94c8, // GIO_AON_IODIR_LO
.offset_data = 0x94c4, // GIO_AON_DATA_LO 0..17
.mask = 0x00020000, // 1<<17
.shift = 17,
.off_value = 0,
.on_value = 1,
.direction_value = 0,
.old_val = -1,
},
.led_blue = {
.is_present = 0,
},
.led_activity = {
.is_present = 1, // GPIO 13
.offset_direction = 0x94c8, // GIO_AON_IODIR_LO
.offset_data = 0x94c4, // GIO_AON_DATA_LO
.mask = 0x00002000, // 1<<13
.shift = 13,
.off_value = 0,
.on_value = 1,
.direction_value = 0,
.old_val = -1,
},
.led_standby = {
.is_present = 0,
},
.reset_button = {
.is_present = 1, // GPIO 4
.offset_direction = 0x94c8, // GIO_AON_IODIR_LO
.offset_data = 0x94c4, // GIO_AON_DATA_LO
.mask = 0x00000010, // 1<<4
.shift = 4,
.off_value = 0,
.on_value = 1,
.direction_value = 1,
.old_val = -1,
},
.fan_tick = {
.is_present = 1, // GPIO 98
.offset_direction = 0x6768, // GIO_IODIR_EXT_HI
.offset_data = 0x6764, // GIO_DATA_EXT_HI
.mask = 0x00000100, // 1<<8
.shift = 8,
.off_value = 0,
.on_value = 1,
.direction_value = 1,
.old_val = -1,
},
.fan_control = {
.is_present = 1, // PWM 1
.offset_data = 0x6580, // PWM_CTRL ...
.channel = 0,
.open_drain = 1,
},
.temp_monitor = {
.is_present = 1, // 7425 AVS_RO_REGISTERS_0
.offset_data = 0x32b00, // BCHP_AVS_RO_REGISTERS_0_PVT_TEMPERATURE_MNTR_STATUS
.get_temp = get_avs_temperature_74xx,
},
.voltage_monitor = {
.is_present = 1, // 7425 AVS_RO_REGISTERS_0
.offset_data = 0x32b0c, // BCHP_AVS_RO_REGISTERS_0_PVT_1P10V_0_MNTR_STATUS
.get_voltage = get_avs_voltage_74xx,
},
},
{
.name = "GFHD200",
.init = init_gfhd200,
.mmap_base = 0x10400000, // AON_PIN_CTRL ...
.mmap_size = 0x30000,
.led_red = {
.is_present = 1, // GPIO 5
.pinmux_offset = 0x8500, // PIN_MUX_CTRL_0
.pinmux_mask = 0xf0000000,
.pinmux_value = 0x10000000, // LED_LD1 (segment 1 on led digit1)
.offset_data = 0x9018, // GIO_AON_DATA_LO
.mask = 0x00000002, // 1<<1
.shift = 1,
.off_value =1,
.on_value = 0,
.old_val = -1,
},
.led_blue = {
.is_present = 0,
},
.led_activity = {
.is_present = 1, // GPIO 4
.pinmux_offset = 0x8500, // PIN_MUX_CTRL_0
.pinmux_mask = 0x0f000000,
.pinmux_value = 0x01000000, // LED_LD0 (segment 0 on led digit1)
.offset_data = 0x9018, // GIO_AON_DATA_LO
.mask = 0x00000001, // 1<<0
.shift = 0,
.off_value = 1,
.on_value = 0,
.old_val = -1,
},
.led_standby = {
.is_present = 0,
},
.reset_button = {
.is_present = 1, // GPIO 3
.offset_direction = 0x9808, // GIO_AON_IODIR_LO
.offset_data = 0x9804, // GIO_AON_DATA_LO
.mask = 0x00000008, // 1<<3
.shift = 3,
.off_value = 0,
.on_value = 1,
.direction_value = 1,
.old_val = -1,
},
.fan_control = {
.is_present = 0,
},
.temp_monitor = {
.is_present = 1, // 7429 AVS_RO_REGISTERS_0
.offset_data = 0x23300, // BCHP_AVS_RO_REGISTERS_0_PVT_TEMPERATURE_MNTR_STATUS
.get_temp = get_avs_temperature_74xx,
},
.voltage_monitor = {
.is_present = 1, // 7429 AVS_RO_REGISTERS_0
.offset_data = 0x2330c, // BCHP_AVS_RO_REGISTERS_0_PVT_1P10V_0_MNTR_STATUS
.get_voltage = get_avs_voltage_74xx,
},
},
{
.name = "GFHD254",
.init = init_gfhd254,
.mmap_base = 0xf0400000, // AON_PIN_CTRL ...
.mmap_size = 0xe0000,
.led_red = {
.is_present = 1, // AON_GPIO_05
.pinmux_offset = 0x10700, // PIN_MUX_CTRL_0
.pinmux_mask = 0x00f00000,
.pinmux_value = 0x00200000, // LED_LD_13
.offset_data = 0x1701c, // LDK_DIGIT1
.mask = 1<<13, // 1<<13
.shift = 13,
.off_value =1,
.on_value = 0,
.old_val = -1,
},
.led_blue = {
.is_present = 0,
},
.led_activity = {
.is_present = 1, // AON_GPIO_04
.pinmux_offset = 0x10700, // PIN_MUX_CTRL_0
.pinmux_mask = 0x000f0000,
.pinmux_value = 0x00020000, // LED_LD_12
.offset_data = 0x1701c, // LDK_DIGIT1
.mask = 1<<12, // 1<<12
.shift = 12,
.off_value = 1,
.on_value = 0,
.old_val = -1,
},
.led_standby = {
.is_present = 0,
},
.reset_button = {
.is_present = 1, // GPIO_009
.pinmux_offset = 0x4120, // SUN_TOP_CTRL_PIN_MUX_CTRL_8
.pinmux_mask = 0xf0000000,
.pinmux_value = 0x00000000, // GPIO_009
.offset_direction = 0xa608, // GIO_IODIR_LO
.offset_data = 0xa604, // GIO_DATA_LO
.mask = 0x00000200, // 1<<9
.shift = 9,
.off_value = 0,
.on_value = 1,
.direction_value = 1,
.old_val = -1,
},
.fan_tick = {
.is_present = 1, // GPIO 78
.offset_direction = 0xa648, // GIO_IODIR_EXT_HI
.offset_data = 0xa644, // GIO_DATA_EXT_HI
.mask = 1<<14,
.shift = 14,
.off_value = 0,
.on_value = 1,
.direction_value = 1,
.old_val = -1,
},
.fan_control = {
.is_present = 1, // PWM 3
.offset_data = 0x9000, // PWM_CTRL ...
.channel = 1,
.open_drain = 0,
},
.temp_monitor = {
.is_present = 1, // 7252 AVS_RO_REGISTERS_0
.offset_data = 0xd2200, // BCHP_AVS_RO_REGISTERS_0_PVT_TEMPERATURE_MNTR_STATUS
.get_temp = get_avs_temperature_7252,
},
.voltage_monitor = {
.is_present = 1, // 7252 AVS_RO_REGISTERS_0
.offset_data = 0xd220c, // BCHP_AVS_RO_REGISTERS_0_PVT_1V_0_MNTR_STATUS
.get_voltage = get_avs_voltage_7252,
},
}
};
struct platform_info *platform = NULL;
/* set LED/Keypad timings to control LED brightness */
static void init_gfhd200(UNUSED struct platform_info* p) {
volatile uint32_t* reg;
reg = mmap_addr + 0x9034; // LDK_CONTROL
*reg = 0x01; // reset
*reg = 0x18; // ver=1 inv_led=1
reg = mmap_addr + 0x9008; // LDK_PRESCHI, LO (clock divisor)
reg[0] = 0x00;
reg[1] = 0x10; // tick = clock / 0x0010, not sure what clock is
reg = mmap_addr + 0x9010; // LDK_DUTYOFF, ON
reg[0] = 0x40;
reg[1] = 0xc0; // 0x40 off ticks then 0xc0 on ticks == 75% brightness
}
/* set LED/Keypad timings to control LED brightness */
static void init_gfhd254(UNUSED struct platform_info* p) {
volatile uint32_t* reg;
// The led display controller works like this:
// - there are 16 gpios (we connect our leds to 2 of these)
// - the controller steps through digit1-4 and then status
// - bit0 in a register maps to a particular gpio
// when digit1 is being displayed the controller uses digit1_bit[15:0] to
// drive the gpios. When digit 2 is displayed digit2[15:0] and so forth.
// - duty_on controls how many clocks a digit is displayed
// - duty_off controls number of clocks of all off time when switching
// between digits
//
// To get 100% brightness you set all of digit1-4 and status to 1 for the led
// you are drivng, and set duty_off to 0.
//
// Here we also invert the values, so a 1 means off, and 0 means on, this is
// done because for unknown reasons the time between status and digit1 is on,
// so we can't get the brightness to 0 unless we invert.
//
// For simplicity we enable only one of the digits because the leds are
// already insanely bright, and then to disable an led we simply toggle the
// bit in that one digit register.
//
// The red led is attached to bit 13 and blue led is attached to bit 12.
reg = mmap_addr + 0x17034; // LDK_CONTROL
*reg = 0x01; // reset
*reg = 0x18; // ver=1
reg = mmap_addr + 0x17018;
reg[0] = 0xffff; // LDK_DIGIT2
reg[1] = 0xcfff; // LDK_DIGIT1
reg[2] = 0xffff; // LDK_DIGIT4
reg[3] = 0xffff; // LDK_DIGIT3
reg[5] = 0xffff; // LDK_STATUS
reg = mmap_addr + 0x17008; // LDK_PRESCHI, LO (clock divisor)
reg[0] = 0x00;
reg[1] = 0x10; // tick = clock / 0x0010, not sure what clock is
reg = mmap_addr + 0x17010; // LDK_DUTYOFF, ON
reg[0] = 0x40;
reg[1] = 0xc0; // 0x40 off ticks then 0xc0 on ticks to dim a bit more.
// The fan is connected to PWM3, the register PWM3_CWORD_LSB is set to 1,
// this is the frequency of the PWM, the other pwm register control
// the duty cycle.
reg = mmap_addr + 0x9014; // PWM3_CWORD_LSB
reg[0] = 1;
}
// Set the given PWM (pulse width modulator) to the given percent duty cycle.
static void set_pwm(struct Fan *f, int percent) {
volatile uint32_t* reg;
uint32_t mask0, val0, mask1, val1, on;
if (percent < 0) percent = 0;
if (percent > 100) percent = 100;
if (f->old_percent == percent) return;
f->old_percent = percent;
reg = mmap_addr + f->offset_data;
if (f->channel == 0) {
mask0 = 0xf0; // preserve other channel
val0 = 0x01; // open-drain|start
if (f->open_drain)
val0 |= 0x08;
mask1 = 0x10; // preserve
val1 = 0x01; // constant-freq
on = 6;
} else {
mask0 = 0x0f; // see above
val0 = 0x10;
if (f->open_drain)
val0 |= 0x80;
mask1 = 0x01;
val1 = 0x10;
on = 8;
}
reg[0] = (reg[0] & mask0) | val0;
reg[1] = (reg[1] & mask1) | val1;
reg[on] = 0x63 * percent/100; // 0x63 is what old code used
reg[on+1] = 0x63;
}
// Get the CPU temperature. I think it's in Celsius.
static double get_avs_temperature_74xx(struct Temp* t) {
volatile uint32_t* reg;
uint32_t value, valid, raw_data;
reg = mmap_addr + t->offset_data;
value = *reg;
// see 7425-PR500-RDS.pdf
valid = (value & 0x00000400) >> 10;
raw_data = value & 0x000003ff;
if (!valid) return -1.0;
return (418000 - (556 * raw_data)) / 1000.0;
}
static double get_avs_temperature_7252(struct Temp* t) {
volatile uint32_t* reg;
uint32_t value, valid, raw_data;
reg = mmap_addr + t->offset_data;
value = *reg;
valid = (value & 0x00000400) >> 10;
raw_data = value & 0x000003ff;
if (!valid) return -1.0;
return 410.04 - (0.48705 * raw_data);
}
static double get_avs_voltage_74xx(struct Voltage* v) {
volatile uint32_t* reg;
uint32_t value, valid, raw_data;
reg = mmap_addr + v->offset_data;
value = *reg;
// see 7425-PR500-RDS.pdf
valid = (value & 0x00000400) >> 10;
raw_data = value & 0x000003ff;
if (!valid) return -1.0;
return ((990 * raw_data * 8) / (7*1024)) / 1000.0;
}
static double get_avs_voltage_7252(struct Voltage* v) {
volatile uint32_t* reg;
uint32_t value, valid, raw_data;
reg = mmap_addr + v->offset_data;
value = *reg;
valid = (value & 0x00000400) >> 10;
raw_data = value & 0x000003ff;
if (!valid) return -1.0;
return ((880.0/1024.0)/(0.7)*raw_data) / 1000;
}
// Write the given GPIO pin.
static void set_gpio(struct Gpio *g, int level) {
volatile uint32_t* reg;
uint32_t value;
if (g->old_val == level) {
// If this is the same value as last time, don't do anything, for two
// reasons:
// 1) If you set the gpio too often, it seems to stay low (the led
// stays off).
// 2) If some process other than us is twiddling a led, this way we
// won't interfere with it.
return;
}
g->old_val = level;
reg = mmap_addr + g->offset_data;
value = *reg;
value &= ~g->mask;
value |= (level ? g->on_value : g->off_value) << g->shift;
*reg = value;
}
// Read the given GPIO pin
static int get_gpio(struct Gpio *g) {
volatile uint32_t* reg;
uint32_t value;
reg = mmap_addr + g->offset_data;
value = (*reg & g->mask) >> g->shift;
return (value == g->on_value);
}
// initialize GPIO to input or output
static void set_direction(struct Gpio *g)
{
volatile uint32_t* reg;
uint32_t value;
if (!g->is_present || g->offset_direction == 0)
return;
reg = mmap_addr + g->offset_direction;
value = *reg;
value &= ~g->mask;
value |= g->direction_value << g->shift;
*reg = value;
}
// initialize pin to LED or GPIO etc
static void set_pinmux(struct Gpio *g) {
volatile uint32_t* reg;
uint32_t value;
if (!g->is_present || g->pinmux_offset == 0)
return;
reg = mmap_addr + g->pinmux_offset;
value = *reg;
value &= ~g->pinmux_mask;
value |= g->pinmux_value;
*reg = value;
}
// Same as time(), but in monotonic clock milliseconds instead.
static long long msec_now(void) {
struct timespec ts;
CHECK(clock_gettime(CLOCK_MONOTONIC, &ts));
return ((long long)ts.tv_sec) * 1000 + (ts.tv_nsec / 1000000);
}
static void platform_cleanup(void) {
if (mmap_addr != MAP_FAILED) {
if (munmap((void*) mmap_addr, mmap_size) < 0) {
perror("munmap");
}
mmap_addr = MAP_FAILED;
mmap_size = 0;
}
if (mmap_fd >= 0) {
close(mmap_fd);
mmap_fd = -1;
}
}
static int platform_init(struct platform_info* p) {
platform_cleanup();
mmap_fd = open(DEVMEM, O_RDWR);
if (mmap_fd < 0) {
perror(DEVMEM);
return -1;
}
mmap_size = p->mmap_size;
mmap_addr = mmap(NULL, mmap_size, PROT_READ | PROT_WRITE, MAP_SHARED,
mmap_fd, p->mmap_base);
if (mmap_addr == MAP_FAILED) {
perror("mmap");
platform_cleanup();
return -1;
}
return 0;
}
static struct platform_info *get_platform_info(const char *platform_name) {
int lim = sizeof(platforms) / sizeof(platforms[0]);
for (int i = 0; i < lim; ++i) {
struct platform_info *p = &platforms[i];
if (0 == strncmp(platform_name, p->name, strlen(p->name))) {
return p;
}
}
fprintf(stderr, "No support for platform %s", platform_name);
exit(1);
}
// read a file containing a single short string.
// Returns a static buffer. Be careful!
static char *read_file(const char *filename) {
static char buf[1024];
int fd = open(filename, O_RDONLY);
if (fd >= 0) {
size_t got = read(fd, buf, sizeof(buf) - 1);
buf[got] = '\0';
close(fd);
return buf;
}
buf[0] = '\0';
return buf;
}
/* API follows */
int has_fan(void) {
return (platform->fan_control.is_present);
}
/*
* We're polling at a very high frequency, which is a pain. This would be
* slightly less gross inside the kernel (for less context switching and
* because it could more easily use the tick interrupt instead of polling).
*
* This setting isn't as bad as it sounds, though, because we don't poll
* 100% of the time; we only do it for a fraction of a second every now
* and then.
*
* Fans in CPE1.0 generate 2 pulses per revolution
*/
#define FAN_POLL_HZ 2000
#define FAN_USEC_PER_TICK (1000000 / (FAN_POLL_HZ))
#define PULSES_PER_REV 2
int get_fan(void) {
long long start = 0, end = 0;
int inner_loop_ticks = 0;
int reads = 0, fan_flips = 0;
long fan_loop_time = 0;
int divider = 20; // poll for 1/20th of a sec
int start_fan = get_gpio(&platform->fan_tick), last_fan = start_fan;
inner_loop_ticks = FAN_POLL_HZ / divider + 1;
for (int tick = 0; tick < inner_loop_ticks; tick++) {
int cur_fan = get_gpio(&platform->fan_tick);
if (last_fan != cur_fan && start_fan == cur_fan) {
if (!start) {
start = msec_now();
} else {
fan_flips++;
end = msec_now();
}
}
reads++;
last_fan = cur_fan;
usleep(FAN_USEC_PER_TICK);
}
fan_loop_time += end - start;
// return pulses/sec from the fan
// number of pulses/rotation varies with fan model, so this isn't rpm
return (fan_flips * 1000 / (fan_loop_time + 1) / PULSES_PER_REV);
}
void set_fan(int wantspeed) {
set_pwm(&platform->fan_control, wantspeed);
}
double get_cpu_temperature(void) {
if (platform->temp_monitor.get_temp)
return platform->temp_monitor.get_temp(&platform->temp_monitor);
return -1;
}
double get_cpu_voltage(void) {
if (platform->voltage_monitor.get_voltage)
return platform->voltage_monitor.get_voltage(&platform->voltage_monitor);
return -1;
}
int get_reset_button() {
return !get_gpio(&platform->reset_button); /* inverted */
}
int has_red_led(void) {
return (platform->led_red.is_present);
}
int has_blue_led(void) {
return (platform->led_blue.is_present);
}
int has_activity_led(void) {
return (platform->led_activity.is_present);
}
int has_standby_led(void) {
return (platform->led_standby.is_present);
}
int get_red_led(void) {
return get_gpio(&platform->led_red);
}
int get_blue_led(void) {
return get_gpio(&platform->led_blue);
}
int get_activity_led(void) {
return get_gpio(&platform->led_activity);
}
int get_standby_led(void) {
return get_gpio(&platform->led_standby);
}
void set_red_led(int level) {
set_gpio(&platform->led_red, level ? 1 : 0);
}
void set_blue_led(int level) {
set_gpio(&platform->led_blue, level ? 1 : 0);
}
void set_activity_led(int level) {
set_gpio(&platform->led_activity, level ? 1 : 0);
}
void set_standby_led(int level) {
set_gpio(&platform->led_standby, level ? 1 : 0);
}
static void init_platform(struct platform_info* p) {
if (p->init) {
(*p->init)(p);
}
}
static void initialize_gpios(void) {
init_platform(platform);
set_pinmux(&platform->led_red);
set_pinmux(&platform->led_blue);
set_pinmux(&platform->led_activity);
set_pinmux(&platform->led_standby);
set_direction(&platform->led_red);
set_direction(&platform->led_blue);
set_direction(&platform->led_activity);
set_direction(&platform->led_standby);
set_direction(&platform->reset_button);
set_direction(&platform->fan_tick);
}
/* standard API follows */
PinHandle PinCreate(void) {
PinHandle handle = (PinHandle) calloc(1, sizeof (*handle));
if (handle == NULL) {
perror("calloc(PinHandle)");
return NULL;
}
platform = get_platform_info(read_file("/etc/platform"));
if (platform_init(platform) < 0) {
fprintf(stderr, "platform_init failed\n");
PinDestroy(handle);
return NULL;
}
initialize_gpios();
return handle;
}
void PinDestroy(PinHandle handle) {
if (handle == NULL)
return;
platform_cleanup();
free(handle);
}
int PinIsPresent(PinHandle handle, PinId id) {
if (handle == NULL) return PIN_ERROR;
switch (id) {
case PIN_LED_RED:
return has_red_led();
case PIN_LED_BLUE:
return has_blue_led();
case PIN_LED_ACTIVITY:
return has_activity_led();
case PIN_LED_STANDBY:
return has_standby_led();
case PIN_FAN_CHASSIS:
return has_fan();
case PIN_BUTTON_RESET:
case PIN_TEMP_CPU:
case PIN_MVOLTS_CPU:
return 1;
case PIN_TEMP_EXTERNAL:
case PIN_NONE:
case PIN_MAX:
return 0;
}
return 0;
}
PinStatus PinValue(PinHandle handle, PinId id, int* valueP) {
if (handle == NULL) return PIN_ERROR;
switch (id) {
case PIN_LED_RED:
*valueP = get_red_led();
break;
case PIN_LED_BLUE:
*valueP = get_blue_led();
break;
case PIN_LED_ACTIVITY:
*valueP = get_activity_led();
break;
case PIN_LED_STANDBY:
*valueP = get_standby_led();
break;
case PIN_BUTTON_RESET:
*valueP = get_reset_button();
break;
case PIN_TEMP_CPU:
*valueP = (int)(get_cpu_temperature() * 1000);
break;
case PIN_MVOLTS_CPU:
*valueP = (int)(get_cpu_voltage() * 1000);
break;
case PIN_FAN_CHASSIS:
*valueP = get_fan();
break;
case PIN_TEMP_EXTERNAL:
case PIN_NONE:
case PIN_MAX:
*valueP = -1;
return PIN_ERROR;
}
return PIN_OKAY;
}
PinStatus PinSetValue(PinHandle handle, PinId id, int value) {
if (handle == NULL) return PIN_ERROR;
switch (id) {
case PIN_LED_RED:
set_red_led(value);
break;
case PIN_LED_BLUE:
set_blue_led(value);
break;
case PIN_LED_ACTIVITY:
set_activity_led(value);
break;
case PIN_LED_STANDBY:
set_standby_led(value);
break;
case PIN_FAN_CHASSIS:
set_fan(value);
break;
case PIN_BUTTON_RESET:
case PIN_MVOLTS_CPU:
case PIN_TEMP_CPU:
case PIN_TEMP_EXTERNAL:
case PIN_NONE:
case PIN_MAX:
return PIN_ERROR;
}
return PIN_OKAY;
}
#endif /* BROADCOM */