| /* |
| * (C) Copyright 2005 2N TELEKOMUNIKACE, Ladislav Michl |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #include <common.h> |
| #include <i2c.h> |
| #include <flash.h> |
| #include <nand.h> |
| |
| #include <asm/io.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| int board_init(void) |
| { |
| /* arch number of NetStar board */ |
| gd->bd->bi_arch_number = MACH_TYPE_NETSTAR; |
| |
| /* adress of boot parameters */ |
| gd->bd->bi_boot_params = 0x10000100; |
| |
| return 0; |
| } |
| |
| int dram_init(void) |
| { |
| gd->bd->bi_dram[0].start = PHYS_SDRAM_1; |
| gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; |
| |
| /* Take the Ethernet controller out of reset and wait |
| * for the EEPROM load to complete. */ |
| *((volatile unsigned short *) GPIO_DATA_OUTPUT_REG) |= 0x80; |
| udelay(10); /* doesn't work before interrupt_init call */ |
| *((volatile unsigned short *) GPIO_DATA_OUTPUT_REG) &= ~0x80; |
| udelay(500); |
| |
| return 0; |
| } |
| |
| int misc_init_r(void) |
| { |
| #if defined(CONFIG_RTC_DS1307) |
| /* enable trickle charge */ |
| i2c_reg_write(CONFIG_SYS_I2C_RTC_ADDR, 0x10, 0xaa); |
| #endif |
| return 0; |
| } |
| |
| int board_late_init(void) |
| { |
| return 0; |
| } |
| |
| #if defined(CONFIG_CMD_FLASH) |
| ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t * info) |
| { |
| if (banknum == 0) { /* AM29LV800 boot flash */ |
| info->portwidth = FLASH_CFI_16BIT; |
| info->chipwidth = FLASH_CFI_BY16; |
| info->interface = FLASH_CFI_X16; |
| return 1; |
| } |
| |
| return 0; |
| } |
| #endif |
| |
| #if defined(CONFIG_CMD_NAND) |
| /* |
| * hardware specific access to control-lines |
| * |
| * NAND_NCE: bit 0 - don't care |
| * NAND_CLE: bit 1 -> bit 1 (0x0002) |
| * NAND_ALE: bit 2 -> bit 2 (0x0004) |
| */ |
| static void netstar_nand_hwcontrol(struct mtd_info *mtd, int cmd, |
| unsigned int ctrl) |
| { |
| struct nand_chip *chip = mtd->priv; |
| unsigned long mask; |
| |
| if (cmd == NAND_CMD_NONE) |
| return; |
| |
| mask = (ctrl & NAND_CLE) ? 0x02 : 0; |
| if (ctrl & NAND_ALE) |
| mask |= 0x04; |
| writeb(cmd, (unsigned long)chip->IO_ADDR_W | mask); |
| } |
| |
| int board_nand_init(struct nand_chip *nand) |
| { |
| nand->options = NAND_SAMSUNG_LP_OPTIONS; |
| nand->ecc.mode = NAND_ECC_SOFT; |
| nand->cmd_ctrl = netstar_nand_hwcontrol; |
| nand->chip_delay = 400; |
| return 0; |
| } |
| #endif |