| /* |
| * Copyright (C) 2006 Freescale Semiconductor, Inc. |
| * Dave Liu <daveliu@freescale.com> |
| * |
| * Copyright (C) 2007 Logic Product Development, Inc. |
| * Peter Barada <peterb@logicpd.com> |
| * |
| * Copyright (C) 2007 MontaVista Software, Inc. |
| * Anton Vorontsov <avorontsov@ru.mvista.com> |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| */ |
| #define CONFIG_E300 1 /* E300 family */ |
| #define CONFIG_QE 1 /* Has QE */ |
| #define CONFIG_MPC83xx 1 /* MPC83xx family */ |
| #define CONFIG_MPC8360 1 /* MPC8360 CPU specific */ |
| #define CONFIG_MPC8360ERDK 1 /* MPC8360ERDK board specific */ |
| |
| /* |
| * System Clock Setup |
| */ |
| #ifdef CONFIG_CLKIN_33MHZ |
| #define CONFIG_83XX_CLKIN 33333333 |
| #define CONFIG_SYS_CLK_FREQ 33333333 |
| #define PCI_33M 1 |
| #define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_10X1 |
| #else |
| #define CONFIG_83XX_CLKIN 66000000 |
| #define CONFIG_SYS_CLK_FREQ 66000000 |
| #define PCI_66M 1 |
| #define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_5X1 |
| #endif /* CONFIG_CLKIN_33MHZ */ |
| |
| /* |
| * Hardware Reset Configuration Word |
| */ |
| #define CONFIG_SYS_HRCW_LOW (\ |
| HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ |
| HRCWL_DDR_TO_SCB_CLK_1X1 |\ |
| HRCWL_CSB_TO_CLKIN_MPC8360ERDK |\ |
| HRCWL_CORE_TO_CSB_2X1 |\ |
| HRCWL_CE_TO_PLL_1X15) |
| |
| #define CONFIG_SYS_HRCW_HIGH (\ |
| HRCWH_PCI_HOST |\ |
| HRCWH_PCI1_ARBITER_ENABLE |\ |
| HRCWH_PCICKDRV_ENABLE |\ |
| HRCWH_CORE_ENABLE |\ |
| HRCWH_FROM_0X00000100 |\ |
| HRCWH_BOOTSEQ_DISABLE |\ |
| HRCWH_SW_WATCHDOG_DISABLE |\ |
| HRCWH_ROM_LOC_LOCAL_16BIT |\ |
| HRCWH_SECONDARY_DDR_DISABLE |\ |
| HRCWH_BIG_ENDIAN |\ |
| HRCWH_LALE_EARLY) |
| |
| /* |
| * System IO Config |
| */ |
| #define CONFIG_SYS_SICRH 0x00000000 |
| #define CONFIG_SYS_SICRL 0x40000000 |
| |
| #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ |
| #define CONFIG_BOARD_EARLY_INIT_R |
| |
| /* |
| * IMMR new address |
| */ |
| #define CONFIG_SYS_IMMR 0xE0000000 |
| |
| /* |
| * DDR Setup |
| */ |
| #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE |
| #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE |
| #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ |
| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) |
| |
| #define CONFIG_SYS_83XX_DDR_USES_CS0 |
| |
| #define CONFIG_DDR_ECC /* support DDR ECC function */ |
| #define CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ |
| |
| /* |
| * DDRCDR - DDR Control Driver Register |
| */ |
| #define CONFIG_SYS_DDRCDR_VALUE 0x80080001 |
| |
| #undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup */ |
| |
| /* |
| * Manually set up DDR parameters |
| */ |
| #define CONFIG_DDR_II |
| #define CONFIG_SYS_DDR_SIZE 256 /* MB */ |
| #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f |
| #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | \ |
| CSCONFIG_COL_BIT_10 | CSCONFIG_ODT_WR_ACS) |
| #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | SDRAM_CFG_ECC_EN) |
| #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 |
| #define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) |
| #define CONFIG_SYS_DDR_INTERVAL ((256 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ |
| (1115 << SDRAM_INTERVAL_REFINT_SHIFT)) |
| #define CONFIG_SYS_DDR_MODE 0x47800432 |
| #define CONFIG_SYS_DDR_MODE2 0x8000c000 |
| |
| #define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ |
| (9 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ |
| (3 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ |
| (3 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ |
| (0 << TIMING_CFG0_WWT_SHIFT) | \ |
| (0 << TIMING_CFG0_RRT_SHIFT) | \ |
| (0 << TIMING_CFG0_WRT_SHIFT) | \ |
| (0 << TIMING_CFG0_RWT_SHIFT)) |
| |
| #define CONFIG_SYS_DDR_TIMING_1 (( TIMING_CFG1_CASLAT_30) | \ |
| ( 2 << TIMING_CFG1_WRTORD_SHIFT) | \ |
| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ |
| ( 3 << TIMING_CFG1_WRREC_SHIFT) | \ |
| (10 << TIMING_CFG1_REFREC_SHIFT) | \ |
| ( 3 << TIMING_CFG1_ACTTORW_SHIFT) | \ |
| ( 8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ |
| ( 3 << TIMING_CFG1_PRETOACT_SHIFT)) |
| |
| #define CONFIG_SYS_DDR_TIMING_2 ((9 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ |
| (4 << TIMING_CFG2_CKE_PLS_SHIFT) | \ |
| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ |
| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ |
| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ |
| (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ |
| (0 << TIMING_CFG2_CPO_SHIFT)) |
| |
| #define CONFIG_SYS_DDR_TIMING_3 0x00000000 |
| |
| /* |
| * Memory test |
| */ |
| #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ |
| #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ |
| #define CONFIG_SYS_MEMTEST_END 0x00100000 |
| |
| /* |
| * The reserved memory |
| */ |
| #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ |
| #define CONFIG_SYS_FLASH_BASE 0xFF800000 /* FLASH base address */ |
| |
| #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) |
| #define CONFIG_SYS_RAMBOOT |
| #else |
| #undef CONFIG_SYS_RAMBOOT |
| #endif |
| |
| #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ |
| #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ |
| |
| /* |
| * Initial RAM Base Address Setup |
| */ |
| #define CONFIG_SYS_INIT_RAM_LOCK 1 |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ |
| #define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */ |
| #define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) |
| |
| /* |
| * Local Bus Configuration & Clock Setup |
| */ |
| #define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4) |
| #define CONFIG_SYS_LBC_LBCR 0x00000000 |
| |
| /* |
| * FLASH on the Local Bus |
| */ |
| #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ |
| #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ |
| #define CONFIG_SYS_FLASH_SIZE 8 /* max FLASH size is 32M */ |
| #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use intel Flash protection. */ |
| |
| #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */ |
| #define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ |
| |
| #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | /* Flash Base address */ \ |
| (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ |
| BR_V) /* valid */ |
| #define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \ |
| OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ |
| OR_GPCM_XACS | OR_GPCM_SCY_15 | \ |
| OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ |
| |
| #undef CONFIG_SYS_FLASH_CHECKSUM |
| |
| /* |
| * NAND flash on the local bus |
| */ |
| #define CONFIG_SYS_NAND_BASE 0x60000000 |
| #define CONFIG_CMD_NAND 1 |
| #define CONFIG_NAND_FSL_UPM 1 |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_MTD_NAND_VERIFY_WRITE |
| #define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ |
| |
| #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE |
| #define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000001b /* Access window size 4K */ |
| |
| /* Port size 8 bit, UPMA */ |
| #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE | 0x00000881) |
| #define CONFIG_SYS_OR1_PRELIM 0xfc000001 |
| |
| /* |
| * Fujitsu MB86277 (MINT) graphics controller |
| */ |
| #define CONFIG_SYS_VIDEO_BASE 0x70000000 |
| |
| #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VIDEO_BASE |
| #define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000019 /* Access window size 64MB */ |
| |
| /* Port size 32 bit, UPMB */ |
| #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_VIDEO_BASE | 0x000018a1) /* PS=11, UPMB */ |
| #define CONFIG_SYS_OR2_PRELIM 0xfc000001 /* (64MB, EAD=1) */ |
| |
| /* |
| * Serial Port |
| */ |
| #define CONFIG_CONS_INDEX 1 |
| #undef CONFIG_SERIAL_SOFTWARE_FIFO |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200,} |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) |
| |
| #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ |
| /* Use the HUSH parser */ |
| #define CONFIG_SYS_HUSH_PARSER |
| #ifdef CONFIG_SYS_HUSH_PARSER |
| #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " |
| #endif |
| |
| /* Pass open firmware flat tree */ |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_OF_BOARD_SETUP 1 |
| #define CONFIG_OF_STDOUT_VIA_ALIAS |
| |
| /* I2C */ |
| #define CONFIG_HARD_I2C /* I2C with hardware support */ |
| #undef CONFIG_SOFT_I2C /* I2C bit-banged */ |
| #define CONFIG_FSL_I2C |
| #define CONFIG_I2C_MULTI_BUS |
| #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ |
| #define CONFIG_SYS_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_I2C_NOPROBES {{0x52}} /* Don't probe these addrs */ |
| #define CONFIG_SYS_I2C_OFFSET 0x3000 |
| #define CONFIG_SYS_I2C2_OFFSET 0x3100 |
| |
| /* |
| * General PCI |
| * Addresses are mapped 1-1. |
| */ |
| #define CONFIG_PCI |
| |
| #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 |
| #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE |
| #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ |
| #define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 |
| #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE |
| #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ |
| #define CONFIG_SYS_PCI1_IO_BASE 0xE0300000 |
| #define CONFIG_SYS_PCI1_IO_PHYS 0xE0300000 |
| #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ |
| |
| #ifdef CONFIG_PCI |
| |
| #define CONFIG_NET_MULTI |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| |
| #undef CONFIG_EEPRO100 |
| #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ |
| |
| #endif /* CONFIG_PCI */ |
| |
| |
| #ifndef CONFIG_NET_MULTI |
| #define CONFIG_NET_MULTI 1 |
| #endif |
| |
| /* |
| * QE UEC ethernet configuration |
| */ |
| #define CONFIG_UEC_ETH |
| #define CONFIG_ETHPRIME "FSL UEC0" |
| |
| #define CONFIG_UEC_ETH1 /* GETH1 */ |
| |
| #ifdef CONFIG_UEC_ETH1 |
| #define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ |
| #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE |
| #define CONFIG_SYS_UEC1_TX_CLK QE_CLK9 |
| #define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH |
| #define CONFIG_SYS_UEC1_PHY_ADDR 2 |
| #define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_1000_RGMII_RXID |
| #endif |
| |
| #define CONFIG_UEC_ETH2 /* GETH2 */ |
| |
| #ifdef CONFIG_UEC_ETH2 |
| #define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */ |
| #define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE |
| #define CONFIG_SYS_UEC2_TX_CLK QE_CLK4 |
| #define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH |
| #define CONFIG_SYS_UEC2_PHY_ADDR 4 |
| #define CONFIG_SYS_UEC2_INTERFACE_MODE ENET_1000_RGMII_RXID |
| #endif |
| |
| /* |
| * Environment |
| */ |
| |
| #ifndef CONFIG_SYS_RAMBOOT |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ |
| #define CONFIG_ENV_SIZE 0x20000 |
| #else /* CONFIG_SYS_RAMBOOT */ |
| #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ |
| #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) |
| #define CONFIG_ENV_SIZE 0x2000 |
| #endif /* CONFIG_SYS_RAMBOOT */ |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_DHCP |
| |
| #if defined(CONFIG_PCI) |
| #define CONFIG_CMD_PCI |
| #endif |
| |
| #if defined(CONFIG_SYS_RAMBOOT) |
| #undef CONFIG_CMD_SAVEENV |
| #undef CONFIG_CMD_LOADS |
| #endif |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /* |
| * Core HID Setup |
| */ |
| #define CONFIG_SYS_HID0_INIT 0x000000000 |
| #define CONFIG_SYS_HID0_FINAL HID0_ENABLE_MACHINE_CHECK |
| #define CONFIG_SYS_HID2 HID2_HBE |
| |
| /* |
| * MMU Setup |
| */ |
| |
| #define CONFIG_HIGH_BATS 1 /* High BATs supported */ |
| |
| /* DDR: cache cacheable */ |
| #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L |
| #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U |
| |
| /* IMMRBAR & PCI IO: cache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L |
| #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U |
| |
| /* NAND: cache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT2L (CONFIG_SYS_NAND_BASE | BATL_PP_10 | BATL_CACHEINHIBIT |\ |
| BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT2U (CONFIG_SYS_NAND_BASE | BATU_BL_64M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L |
| #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U |
| |
| /* FLASH: icache cacheable, but dcache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U |
| |
| /* Stack in dcache: cacheable, no memory coherence */ |
| #define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10) |
| #define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L |
| #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U |
| |
| #define CONFIG_SYS_IBAT5L (CONFIG_SYS_VIDEO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | \ |
| BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT5U (CONFIG_SYS_VIDEO_BASE | BATU_BL_64M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L |
| #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U |
| |
| #ifdef CONFIG_PCI |
| /* PCI MEM space: cacheable */ |
| #define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L |
| #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U |
| /* PCI MMIO space: cache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI1_MMIO_PHYS | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L |
| #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U |
| #else /* CONFIG_PCI */ |
| #define CONFIG_SYS_IBAT6L (0) |
| #define CONFIG_SYS_IBAT6U (0) |
| #define CONFIG_SYS_IBAT7L (0) |
| #define CONFIG_SYS_IBAT7U (0) |
| #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L |
| #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U |
| #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L |
| #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U |
| #endif /* CONFIG_PCI */ |
| |
| /* |
| * Internal Definitions |
| * |
| * Boot Flags |
| */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| #endif |
| |
| /* |
| * Environment Configuration |
| */ |
| #define CONFIG_ENV_OVERWRITE |
| |
| #if defined(CONFIG_UEC_ETH) |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_HAS_ETH2 |
| #define CONFIG_HAS_ETH3 |
| #define CONFIG_ETHADDR 00:04:9f:ef:01:01 |
| #define CONFIG_ETH1ADDR 00:04:9f:ef:01:02 |
| #define CONFIG_ETH2ADDR 00:04:9f:ef:01:03 |
| #define CONFIG_ETH3ADDR 00:04:9f:ef:01:04 |
| #endif |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_LOADADDR a00000 |
| #define CONFIG_HOSTNAME mpc8360erdk |
| #define CONFIG_BOOTFILE uImage |
| |
| #define CONFIG_IPADDR 10.0.0.99 |
| #define CONFIG_SERVERIP 10.0.0.2 |
| #define CONFIG_GATEWAYIP 10.0.0.2 |
| #define CONFIG_NETMASK 255.255.255.0 |
| #define CONFIG_ROOTPATH /nfsroot/ |
| |
| #define CONFIG_BOOTDELAY 2 /* -1 disables auto-boot */ |
| #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0"\ |
| "consoledev=ttyS0\0"\ |
| "loadaddr=a00000\0"\ |
| "fdtaddr=900000\0"\ |
| "fdtfile=mpc836x_rdk.dtb\0"\ |
| "fsfile=fs\0"\ |
| "ubootfile=u-boot.bin\0"\ |
| "mtdparts=mtdparts=60000000.nand-flash:4096k(kernel),128k(dtb),-(rootfs)\0"\ |
| "setbootargs=setenv bootargs console=$consoledev,$baudrate "\ |
| "$mtdparts panic=1\0"\ |
| "adddhcpargs=setenv bootargs $bootargs ip=on\0"\ |
| "addnfsargs=setenv bootargs $bootargs ip=$ipaddr:$serverip:"\ |
| "$gatewayip:$netmask:$hostname:$netdev:off "\ |
| "root=/dev/nfs rw nfsroot=$serverip:$rootpath\0"\ |
| "addnandargs=setenv bootargs $bootargs root=/dev/mtdblock3 "\ |
| "rootfstype=jffs2 rw\0"\ |
| "tftp_get_uboot=tftp 100000 $ubootfile\0"\ |
| "tftp_get_kernel=tftp $loadaddr $bootfile\0"\ |
| "tftp_get_dtb=tftp $fdtaddr $fdtfile\0"\ |
| "tftp_get_fs=tftp c00000 $fsfile\0"\ |
| "nand_erase_kernel=nand erase 0 400000\0"\ |
| "nand_erase_dtb=nand erase 400000 20000\0"\ |
| "nand_erase_fs=nand erase 420000 3be0000\0"\ |
| "nand_write_kernel=nand write.jffs2 $loadaddr 0 400000\0"\ |
| "nand_write_dtb=nand write.jffs2 $fdtaddr 400000 20000\0"\ |
| "nand_write_fs=nand write.jffs2 c00000 420000 $filesize\0"\ |
| "nand_read_kernel=nand read.jffs2 $loadaddr 0 400000\0"\ |
| "nand_read_dtb=nand read.jffs2 $fdtaddr 400000 20000\0"\ |
| "nor_reflash=protect off ff800000 ff87ffff ; erase ff800000 ff87ffff ; "\ |
| "cp.b 100000 ff800000 $filesize\0"\ |
| "nand_reflash_kernel=run tftp_get_kernel nand_erase_kernel "\ |
| "nand_write_kernel\0"\ |
| "nand_reflash_dtb=run tftp_get_dtb nand_erase_dtb nand_write_dtb\0"\ |
| "nand_reflash_fs=run tftp_get_fs nand_erase_fs nand_write_fs\0"\ |
| "nand_reflash=run nand_reflash_kernel nand_reflash_dtb "\ |
| "nand_reflash_fs\0"\ |
| "boot_m=bootm $loadaddr - $fdtaddr\0"\ |
| "dhcpboot=dhcp ; run setbootargs adddhcpargs tftp_get_dtb boot_m\0"\ |
| "nfsboot=run setbootargs addnfsargs tftp_get_kernel tftp_get_dtb "\ |
| "boot_m\0"\ |
| "nandboot=run setbootargs addnandargs nand_read_kernel nand_read_dtb "\ |
| "boot_m\0"\ |
| "" |
| |
| #define CONFIG_BOOTCOMMAND "run dhcpboot" |
| |
| #endif /* __CONFIG_H */ |
