| /* |
| * |
| * BRIEF MODULE DESCRIPTION |
| * OMAP hardware map |
| * |
| * Copyright (C) 2001 RidgeRun, Inc. (http://www.ridgerun.com) |
| * Author: RidgeRun, Inc. |
| * Greg Lonnon (glonnon@ridgerun.com) or info@ridgerun.com |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License as published by the |
| * Free Software Foundation; either version 2 of the License, or (at your |
| * option) any later version. |
| * |
| * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED |
| * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF |
| * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN |
| * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, |
| * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT |
| * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF |
| * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON |
| * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT |
| * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF |
| * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
| * |
| * You should have received a copy of the GNU General Public License along |
| * with this program; if not, write to the Free Software Foundation, Inc., |
| * 675 Mass Ave, Cambridge, MA 02139, USA. |
| */ |
| |
| #include <asm/arch/sizes.h> |
| |
| /* |
| There are 2 sets of general I/O --> |
| 1. GPIO (shared between ARM & DSP, configured by ARM) |
| 2. MPUIO which can be used only by the ARM. |
| |
| Base address FFFB:5000 is where the ARM accesses the MPUIO control registers |
| (see 7.2.2 of the TRM for MPUIO reg definitions). |
| |
| Base address E101:5000 is reserved for ARM access of the same MPUIO control |
| regs, but via the DSP I/O map. This address is unavailable on 1510. |
| |
| Base address FFFC:E000 is where the ARM accesses the GPIO config registers |
| directly via its own peripheral bus. |
| |
| Base address E101:E000 is where the ARM can access the same GPIO config |
| registers, but the access takes place through the ARM port interface (called |
| API or MPUI) via the DSP's peripheral bus (DSP I/O space). |
| |
| Therefore, the ARM should setup the GPIO regs thru the FFFC:E000 addresses |
| instead of the E101:E000 addresses. The DSP has only read access of the pin |
| control register, so this may explain the inability to write to E101:E018. |
| Try accessing pin control reg at FFFC:E018. |
| */ |
| #define OMAP1510_GPIO_BASE 0xfffce000 |
| #define OMAP1510_GPIO_START OMAP1510_GPIO_BASE |
| #define OMAP1510_GPIO_SIZE SZ_4K |
| |
| #define OMAP1510_MCBSP1_BASE 0xE1011000 |
| #define OMAP1510_MCBSP1_SIZE SZ_4K |
| #define OMAP1510_MCBSP1_START 0xE1011000 |
| |
| #define OMAP1510_MCBSP2_BASE 0xFFFB1000 |
| |
| #define OMAP1510_MCBSP3_BASE 0xE1017000 |
| #define OMAP1510_MCBSP3_SIZE SZ_4K |
| #define OMAP1510_MCBSP3_START 0xE1017000 |
| |
| /* |
| * Where's the flush address (for flushing D and I cache?) |
| */ |
| #define FLUSH_BASE 0xdf000000 |
| #define FLUSH_BASE_PHYS 0x00000000 |
| |
| #ifndef __ASSEMBLER__ |
| |
| #define PCIO_BASE 0 |
| |
| /* |
| * RAM definitions |
| */ |
| #define MAPTOPHYS(a) ((unsigned long)(a) - PAGE_OFFSET) |
| #define KERNTOPHYS(a) ((unsigned long)(&a)) |
| #define KERNEL_BASE (0x10008000) |
| #endif |
| |
| /* macro to get at IO space when running virtually */ |
| #define IO_ADDRESS(x) ((x)) |
| |
| /* ---------------------------------------------------------------------------- |
| * OMAP1510 system registers |
| * ---------------------------------------------------------------------------- |
| */ |
| |
| #define OMAP1510_UART1_BASE 0xfffb0000 /* "BLUETOOTH-UART" */ |
| #define OMAP1510_UART2_BASE 0xfffb0800 /* "MODEM-UART" */ |
| #define OMAP1510_RTC_BASE 0xfffb4800 /* RTC */ |
| #define OMAP1510_UART3_BASE 0xfffb9800 /* Shared MPU/DSP UART */ |
| #define OMAP1510_COM_MCBSP2_BASE 0xffff1000 /* Com McBSP2 */ |
| #define OMAP1510_AUDIO_MCBSP_BASE 0xffff1800 /* Audio McBSP2 */ |
| #define OMAP1510_ARMIO_BASE 0xfffb5000 /* keyboard/gpio */ |
| |
| /* |
| * OMAP1510 UART3 Registers |
| */ |
| |
| #define OMAP_MPU_UART3_BASE 0xFFFB9800 /* UART3 through MPU bus */ |
| |
| /* UART3 Registers Maping through MPU bus */ |
| |
| #define UART3_RHR (OMAP_MPU_UART3_BASE + 0) |
| #define UART3_THR (OMAP_MPU_UART3_BASE + 0) |
| #define UART3_DLL (OMAP_MPU_UART3_BASE + 0) |
| #define UART3_IER (OMAP_MPU_UART3_BASE + 4) |
| #define UART3_DLH (OMAP_MPU_UART3_BASE + 4) |
| #define UART3_IIR (OMAP_MPU_UART3_BASE + 8) |
| #define UART3_FCR (OMAP_MPU_UART3_BASE + 8) |
| #define UART3_EFR (OMAP_MPU_UART3_BASE + 8) |
| #define UART3_LCR (OMAP_MPU_UART3_BASE + 0x0C) |
| #define UART3_MCR (OMAP_MPU_UART3_BASE + 0x10) |
| #define UART3_XON1_ADDR1 (OMAP_MPU_UART3_BASE + 0x10) |
| #define UART3_XON2_ADDR2 (OMAP_MPU_UART3_BASE + 0x14) |
| #define UART3_LSR (OMAP_MPU_UART3_BASE + 0x14) |
| #define UART3_TCR (OMAP_MPU_UART3_BASE + 0x18) |
| #define UART3_MSR (OMAP_MPU_UART3_BASE + 0x18) |
| #define UART3_XOFF1 (OMAP_MPU_UART3_BASE + 0x18) |
| #define UART3_XOFF2 (OMAP_MPU_UART3_BASE + 0x1C) |
| #define UART3_SPR (OMAP_MPU_UART3_BASE + 0x1C) |
| #define UART3_TLR (OMAP_MPU_UART3_BASE + 0x1C) |
| #define UART3_MDR1 (OMAP_MPU_UART3_BASE + 0x20) |
| #define UART3_MDR2 (OMAP_MPU_UART3_BASE + 0x24) |
| #define UART3_SFLSR (OMAP_MPU_UART3_BASE + 0x28) |
| #define UART3_TXFLL (OMAP_MPU_UART3_BASE + 0x28) |
| #define UART3_RESUME (OMAP_MPU_UART3_BASE + 0x2C) |
| #define UART3_TXFLH (OMAP_MPU_UART3_BASE + 0x2C) |
| #define UART3_SFREGL (OMAP_MPU_UART3_BASE + 0x30) |
| #define UART3_RXFLL (OMAP_MPU_UART3_BASE + 0x30) |
| #define UART3_SFREGH (OMAP_MPU_UART3_BASE + 0x34) |
| #define UART3_RXFLH (OMAP_MPU_UART3_BASE + 0x34) |
| #define UART3_BLR (OMAP_MPU_UART3_BASE + 0x38) |
| #define UART3_ACREG (OMAP_MPU_UART3_BASE + 0x3C) |
| #define UART3_DIV16 (OMAP_MPU_UART3_BASE + 0x3C) |
| #define UART3_SCR (OMAP_MPU_UART3_BASE + 0x40) |
| #define UART3_SSR (OMAP_MPU_UART3_BASE + 0x44) |
| #define UART3_EBLR (OMAP_MPU_UART3_BASE + 0x48) |
| #define UART3_OSC_12M_SEL (OMAP_MPU_UART3_BASE + 0x4C) |
| #define UART3_MVR (OMAP_MPU_UART3_BASE + 0x50) |
| |
| /* |
| * Configuration Registers |
| */ |
| #define FUNC_MUX_CTRL_0 0xfffe1000 |
| #define FUNC_MUX_CTRL_1 0xfffe1004 |
| #define FUNC_MUX_CTRL_2 0xfffe1008 |
| #define COMP_MODE_CTRL_0 0xfffe100c |
| #define FUNC_MUX_CTRL_3 0xfffe1010 |
| #define FUNC_MUX_CTRL_4 0xfffe1014 |
| #define FUNC_MUX_CTRL_5 0xfffe1018 |
| #define FUNC_MUX_CTRL_6 0xfffe101C |
| #define FUNC_MUX_CTRL_7 0xfffe1020 |
| #define FUNC_MUX_CTRL_8 0xfffe1024 |
| #define FUNC_MUX_CTRL_9 0xfffe1028 |
| #define FUNC_MUX_CTRL_A 0xfffe102C |
| #define FUNC_MUX_CTRL_B 0xfffe1030 |
| #define FUNC_MUX_CTRL_C 0xfffe1034 |
| #define FUNC_MUX_CTRL_D 0xfffe1038 |
| #define PULL_DWN_CTRL_0 0xfffe1040 |
| #define PULL_DWN_CTRL_1 0xfffe1044 |
| #define PULL_DWN_CTRL_2 0xfffe1048 |
| #define PULL_DWN_CTRL_3 0xfffe104c |
| #define GATE_INH_CTRL_0 0xfffe1050 |
| #define VOLTAGE_CTRL_0 0xfffe1060 |
| #define TEST_DBG_CTRL_0 0xfffe1070 |
| |
| #define MOD_CONF_CTRL_0 0xfffe1080 |
| |
| #ifdef CONFIG_OMAP1610 /* 1610 Configuration Register */ |
| |
| #define USB_OTG_CTRL 0xFFFB040C |
| #define USB_TRANSCEIVER_CTRL 0xFFFE1064 |
| #define PULL_DWN_CTRL_4 0xFFFE10AC |
| #define PU_PD_SEL_0 0xFFFE10B4 |
| #define PU_PD_SEL_1 0xFFFE10B8 |
| #define PU_PD_SEL_2 0xFFFE10BC |
| #define PU_PD_SEL_3 0xFFFE10C0 |
| #define PU_PD_SEL_4 0xFFFE10C4 |
| |
| #endif |
| /* |
| * Traffic Controller Memory Interface Registers |
| */ |
| #define TCMIF_BASE 0xfffecc00 |
| #define IMIF_PRIO (TCMIF_BASE + 0x00) |
| #define EMIFS_PRIO_REG (TCMIF_BASE + 0x04) |
| #define EMIFF_PRIO_REG (TCMIF_BASE + 0x08) |
| #define EMIFS_CONFIG_REG (TCMIF_BASE + 0x0c) |
| #define EMIFS_CS0_CONFIG (TCMIF_BASE + 0x10) |
| #define EMIFS_CS1_CONFIG (TCMIF_BASE + 0x14) |
| #define EMIFS_CS2_CONFIG (TCMIF_BASE + 0x18) |
| #define EMIFS_CS3_CONFIG (TCMIF_BASE + 0x1c) |
| #define EMIFF_SDRAM_CONFIG (TCMIF_BASE + 0x20) |
| #define EMIFF_MRS (TCMIF_BASE + 0x24) |
| #define TC_TIMEOUT1 (TCMIF_BASE + 0x28) |
| #define TC_TIMEOUT2 (TCMIF_BASE + 0x2c) |
| #define TC_TIMEOUT3 (TCMIF_BASE + 0x30) |
| #define TC_ENDIANISM (TCMIF_BASE + 0x34) |
| #define EMIFF_SDRAM_CONFIG_2 (TCMIF_BASE + 0x3c) |
| #define EMIF_CFG_DYNAMIC_WS (TCMIF_BASE + 0x40) |
| |
| /* |
| * LCD Panel |
| */ |
| #define TI925_LCD_BASE 0xFFFEC000 |
| #define TI925_LCD_CONTROL (TI925_LCD_BASE) |
| #define TI925_LCD_TIMING0 (TI925_LCD_BASE+0x4) |
| #define TI925_LCD_TIMING1 (TI925_LCD_BASE+0x8) |
| #define TI925_LCD_TIMING2 (TI925_LCD_BASE+0xc) |
| #define TI925_LCD_STATUS (TI925_LCD_BASE+0x10) |
| #define TI925_LCD_SUBPANEL (TI925_LCD_BASE+0x14) |
| |
| #define OMAP_LCD_CONTROL TI925_LCD_CONTROL |
| |
| /* I2C Registers */ |
| |
| #define I2C_BASE 0xfffb3800 |
| |
| #define I2C_REV (I2C_BASE + 0x00) |
| #define I2C_IE (I2C_BASE + 0x04) |
| #define I2C_STAT (I2C_BASE + 0x08) |
| #define I2C_IV (I2C_BASE + 0x0c) |
| #define I2C_BUF (I2C_BASE + 0x14) |
| #define I2C_CNT (I2C_BASE + 0x18) |
| #define I2C_DATA (I2C_BASE + 0x1c) |
| #define I2C_CON (I2C_BASE + 0x24) |
| #define I2C_OA (I2C_BASE + 0x28) |
| #define I2C_SA (I2C_BASE + 0x2c) |
| #define I2C_PSC (I2C_BASE + 0x30) |
| #define I2C_SCLL (I2C_BASE + 0x34) |
| #define I2C_SCLH (I2C_BASE + 0x38) |
| #define I2C_SYSTEST (I2C_BASE + 0x3c) |
| |
| /* I2C masks */ |
| |
| /* I2C Interrupt Enable Register (I2C_IE): */ |
| |
| #define I2C_IE_XRDY_IE (1 << 4) /* Transmit data ready interrupt enable */ |
| #define I2C_IE_RRDY_IE (1 << 3) /* Receive data ready interrupt enable */ |
| #define I2C_IE_ARDY_IE (1 << 2) /* Register access ready interrupt enable */ |
| #define I2C_IE_NACK_IE (1 << 1) /* No acknowledgment interrupt enable */ |
| #define I2C_IE_AL_IE (1 << 0) /* Arbitration lost interrupt enable */ |
| |
| /* I2C Status Register (I2C_STAT): */ |
| |
| #define I2C_STAT_SBD (1 << 15) /* Single byte data */ |
| #define I2C_STAT_BB (1 << 12) /* Bus busy */ |
| #define I2C_STAT_ROVR (1 << 11) /* Receive overrun */ |
| #define I2C_STAT_XUDF (1 << 10) /* Transmit underflow */ |
| #define I2C_STAT_AAS (1 << 9) /* Address as slave */ |
| #define I2C_STAT_AD0 (1 << 8) /* Address zero */ |
| #define I2C_STAT_XRDY (1 << 4) /* Transmit data ready */ |
| #define I2C_STAT_RRDY (1 << 3) /* Receive data ready */ |
| #define I2C_STAT_ARDY (1 << 2) /* Register access ready */ |
| #define I2C_STAT_NACK (1 << 1) /* No acknowledgment interrupt enable */ |
| #define I2C_STAT_AL (1 << 0) /* Arbitration lost interrupt enable */ |
| |
| /* I2C Interrupt Vector Register (I2C_IV): */ |
| |
| /* I2C Interrupt Code Register (I2C_INTCODE): */ |
| |
| #define I2C_INTCODE_MASK 7 |
| #define I2C_INTCODE_NONE 0 |
| #define I2C_INTCODE_AL 1 /* Arbitration lost */ |
| #define I2C_INTCODE_NAK 2 /* No acknowledgement/general call */ |
| #define I2C_INTCODE_ARDY 3 /* Register access ready */ |
| #define I2C_INTCODE_RRDY 4 /* Rcv data ready */ |
| #define I2C_INTCODE_XRDY 5 /* Xmit data ready */ |
| |
| /* I2C Buffer Configuration Register (I2C_BUF): */ |
| |
| #define I2C_BUF_RDMA_EN (1 << 15) /* Receive DMA channel enable */ |
| #define I2C_BUF_XDMA_EN (1 << 7) /* Transmit DMA channel enable */ |
| |
| /* I2C Configuration Register (I2C_CON): */ |
| |
| #define I2C_CON_EN (1 << 15) /* I2C module enable */ |
| #define I2C_CON_BE (1 << 14) /* Big endian mode */ |
| #define I2C_CON_STB (1 << 11) /* Start byte mode (master mode only) */ |
| #define I2C_CON_MST (1 << 10) /* Master/slave mode */ |
| #define I2C_CON_TRX (1 << 9) /* Transmitter/receiver mode (master mode only) */ |
| #define I2C_CON_XA (1 << 8) /* Expand address */ |
| #define I2C_CON_RM (1 << 2) /* Repeat mode (master mode only) */ |
| #define I2C_CON_STP (1 << 1) /* Stop condition (master mode only) */ |
| #define I2C_CON_STT (1 << 0) /* Start condition (master mode only) */ |
| |
| /* I2C System Test Register (I2C_SYSTEST): */ |
| |
| #define I2C_SYSTEST_ST_EN (1 << 15) /* System test enable */ |
| #define I2C_SYSTEST_FREE (1 << 14) /* Free running mode (on breakpoint) */ |
| #define I2C_SYSTEST_TMODE_MASK (3 << 12) /* Test mode select */ |
| #define I2C_SYSTEST_TMODE_SHIFT (12) /* Test mode select */ |
| #define I2C_SYSTEST_SCL_I (1 << 3) /* SCL line sense input value */ |
| #define I2C_SYSTEST_SCL_O (1 << 2) /* SCL line drive output value */ |
| #define I2C_SYSTEST_SDA_I (1 << 1) /* SDA line sense input value */ |
| #define I2C_SYSTEST_SDA_O (1 << 0) /* SDA line drive output value */ |
| |
| /* |
| * MMC/SD Host Controller Registers |
| */ |
| |
| #define OMAP_MMC_CMD 0xFFFB7800 /* MMC Command */ |
| #define OMAP_MMC_ARGL 0xFFFB7804 /* MMC argument low */ |
| #define OMAP_MMC_ARGH 0xFFFB7808 /* MMC argument high */ |
| #define OMAP_MMC_CON 0xFFFB780C /* MMC system configuration */ |
| #define OMAP_MMC_STAT 0xFFFB7810 /* MMC status */ |
| #define OMAP_MMC_IE 0xFFFB7814 /* MMC system interrupt enable */ |
| #define OMAP_MMC_CTO 0xFFFB7818 /* MMC command time-out */ |
| #define OMAP_MMC_DTO 0xFFFB781C /* MMC data time-out */ |
| #define OMAP_MMC_DATA 0xFFFB7820 /* MMC TX/RX FIFO data */ |
| #define OMAP_MMC_BLEN 0xFFFB7824 /* MMC block length */ |
| #define OMAP_MMC_NBLK 0xFFFB7828 /* MMC number of blocks */ |
| #define OMAP_MMC_BUF 0xFFFB782C /* MMC buffer configuration */ |
| #define OMAP_MMC_SPI 0xFFFB7830 /* MMC serial port interface */ |
| #define OMAP_MMC_SDIO 0xFFFB7834 /* MMC SDIO mode configuration */ |
| #define OMAP_MMC_SYST 0xFFFB7838 /* MMC system test */ |
| #define OMAP_MMC_REV 0xFFFB783C /* MMC module version */ |
| #define OMAP_MMC_RSP0 0xFFFB7840 /* MMC command response 0 */ |
| #define OMAP_MMC_RSP1 0xFFFB7844 /* MMC command response 1 */ |
| #define OMAP_MMC_RSP2 0xFFFB7848 /* MMC command response 2 */ |
| #define OMAP_MMC_RSP3 0xFFFB784C /* MMC command response 3 */ |
| #define OMAP_MMC_RSP4 0xFFFB7850 /* MMC command response 4 */ |
| #define OMAP_MMC_RSP5 0xFFFB7854 /* MMC command response 5 */ |
| #define OMAP_MMC_RSP6 0xFFFB7858 /* MMC command response 6 */ |
| #define OMAP_MMC_RSP7 0xFFFB785C /* MMC command response 4 */ |
| |
| /* MMC masks */ |
| |
| #define OMAP_MMC_END_OF_CMD (1 << 0) /* End of command phase */ |
| #define OMAP_MMC_CARD_BUSY (1 << 2) /* Card enter busy state */ |
| #define OMAP_MMC_BLOCK_RS (1 << 3) /* Block received/sent */ |
| #define OMAP_MMC_EOF_BUSY (1 << 4) /* Card exit busy state */ |
| #define OMAP_MMC_DATA_TIMEOUT (1 << 5) /* Data response time-out */ |
| #define OMAP_MMC_DATA_CRC (1 << 6) /* Date CRC error */ |
| #define OMAP_MMC_CMD_TIMEOUT (1 << 7) /* Command response time-out */ |
| #define OMAP_MMC_CMD_CRC (1 << 8) /* Command CRC error */ |
| #define OMAP_MMC_A_FULL (1 << 10) /* Buffer almost full */ |
| #define OMAP_MMC_A_EMPTY (1 << 11) /* Buffer almost empty */ |
| #define OMAP_MMC_OCR_BUSY (1 << 12) /* OCR busy */ |
| #define OMAP_MMC_CARD_IRQ (1 << 13) /* Card IRQ received */ |
| #define OMAP_MMC_CARD_ERR (1 << 14) /* Card status error in response */ |
| |
| /* 2.9.2 MPUI Interface Registers FFFE:C900 */ |
| |
| #define MPUI_CTRL_REG (volatile __u32 *)(0xfffec900) |
| #define MPUI_DEBUG_ADDR (volatile __u32 *)(0xfffec904) |
| #define MPUI_DEBUG_DATA (volatile __u32 *)(0xfffec908) |
| #define MPUI_DEBUG_FLAG (volatile __u16 *)(0xfffec90c) |
| #define MPUI_STATUS_REG (volatile __u16 *)(0xfffec910) |
| #define MPUI_DSP_STATUS_REG (volatile __u16 *)(0xfffec914) |
| #define MPUI_DSP_BOOT_CONFIG (volatile __u16 *)(0xfffec918) |
| #define MPUI_DSP_API_CONFIG (volatile __u16 *)(0xfffec91c) |
| |
| /* 2.9.6 Traffic Controller Memory Interface Registers: */ |
| #define OMAP_IMIF_PRIO_REG 0xfffecc00 |
| #define OMAP_EMIFS_PRIO_REG 0xfffecc04 |
| #define OMAP_EMIFF_PRIO_REG 0xfffecc08 |
| #define OMAP_EMIFS_CONFIG_REG 0xfffecc0c |
| #define OMAP_EMIFS_CS0_CONFIG 0xfffecc10 |
| #define OMAP_EMIFS_CS1_CONFIG 0xfffecc14 |
| #define OMAP_EMIFS_CS2_CONFIG 0xfffecc18 |
| #define OMAP_EMIFS_CS3_CONFIG 0xfffecc1c |
| #define OMAP_EMIFF_SDRAM_CONFIG 0xfffecc20 |
| #define OMAP_EMIFF_MRS 0xfffecc24 |
| #define OMAP_TIMEOUT1 0xfffecc28 |
| #define OMAP_TIMEOUT2 0xfffecc2c |
| #define OMAP_TIMEOUT3 0xfffecc30 |
| #define OMAP_ENDIANISM 0xfffecc34 |
| |
| /* 2.9.10 EMIF Slow Interface Configuration Register (EMIFS_CONFIG_REG): */ |
| #define OMAP_EMIFS_CONFIG_FR (1 << 4) |
| #define OMAP_EMIFS_CONFIG_PDE (1 << 3) |
| #define OMAP_EMIFS_CONFIG_PWD_EN (1 << 2) |
| #define OMAP_EMIFS_CONFIG_BM (1 << 1) |
| #define OMAP_EMIFS_CONFIG_WP (1 << 0) |
| |
| /* |
| * Memory chunk set aside for the Framebuffer in SRAM |
| */ |
| #define SRAM_FRAMEBUFFER_MEMORY OMAP1510_SRAM_BASE |
| |
| |
| /* |
| * DMA |
| */ |
| |
| #define OMAP1510_DMA_BASE 0xFFFED800 |
| #define OMAP_DMA_BASE OMAP1510_DMA_BASE |
| |
| /* Global Register selection */ |
| #define NO_GLOBAL_DMA_ACCESS 0 |
| |
| /* Channel select field |
| * NOTE: all other channels are linear, chan0 is 0, chan1 is 1, etc... |
| */ |
| #define LCD_CHANNEL 0xc |
| |
| /* Register Select Field (LCD) */ |
| #define DMA_LCD_CTRL 0 |
| #define DMA_LCD_TOP_F1_L 1 |
| #define DMA_LCD_TOP_F1_U 2 |
| #define DMA_LCD_BOT_F1_L 3 |
| #define DMA_LCD_BOT_F1_U 4 |
| |
| #define LCD_FRAME_MODE (1<<0) |
| #define LCD_FRAME_IT_IE (1<<1) |
| #define LCD_BUS_ERROR_IT_IE (1<<2) |
| #define LCD_FRAME_1_IT_COND (1<<3) |
| #define LCD_FRAME_2_IT_COND (1<<4) |
| #define LCD_BUS_ERROR_IT_COND (1<<5) |
| #define LCD_SOURCE_IMIF (1<<6) |
| |
| /* |
| * Real-Time Clock |
| */ |
| |
| #define RTC_SECONDS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x00) |
| #define RTC_MINUTES (volatile __u8 *)(OMAP1510_RTC_BASE + 0x04) |
| #define RTC_HOURS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x08) |
| #define RTC_DAYS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x0C) |
| #define RTC_MONTHS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x10) |
| #define RTC_YEARS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x14) |
| #define RTC_CTRL (volatile __u8 *)(OMAP1510_RTC_BASE + 0x40) |
| |
| |
| /* --------------------------------------------------------------------------- |
| * OMAP1510 Interrupt Handlers |
| * --------------------------------------------------------------------------- |
| * |
| */ |
| #define OMAP_IH1_BASE 0xfffecb00 |
| #define OMAP_IH2_BASE 0xfffe0000 |
| #define OMAP1510_ITR 0x0 |
| #define OMAP1510_MASK 0x4 |
| |
| #define INTERRUPT_HANDLER_BASE OMAP_IH1_BASE |
| #define INTERRUPT_INPUT_REGISTER OMAP1510_ITR |
| #define INTERRUPT_MASK_REGISTER OMAP1510_MASK |
| |
| |
| /* --------------------------------------------------------------------------- |
| * OMAP1510 TIMERS |
| * --------------------------------------------------------------------------- |
| * |
| */ |
| |
| #define OMAP1510_32kHz_TIMER_BASE 0xfffb9000 |
| |
| /* 32k Timer Registers */ |
| #define TIMER32k_CR 0x08 |
| #define TIMER32k_TVR 0x00 |
| #define TIMER32k_TCR 0x04 |
| |
| /* 32k Timer Control Register definition */ |
| #define TIMER32k_TSS (1<<0) |
| #define TIMER32k_TRB (1<<1) |
| #define TIMER32k_INT (1<<2) |
| #define TIMER32k_ARL (1<<3) |
| |
| /* MPU Timer base addresses */ |
| #define OMAP1510_MPUTIMER_BASE 0xfffec500 |
| #define OMAP1510_MPUTIMER_OFF 0x00000100 |
| |
| #define OMAP1510_TIMER1_BASE 0xfffec500 |
| #define OMAP1510_TIMER2_BASE 0xfffec600 |
| #define OMAP1510_TIMER3_BASE 0xfffec700 |
| |
| /* MPU Timer Registers */ |
| #define CNTL_TIMER 0 |
| #define LOAD_TIM 4 |
| #define READ_TIM 8 |
| |
| /* CNTL_TIMER register bits */ |
| #define MPUTIM_FREE (1<<6) |
| #define MPUTIM_CLOCK_ENABLE (1<<5) |
| #define MPUTIM_PTV_MASK (0x7<<PTV_BIT) |
| #define MPUTIM_PTV_BIT 2 |
| #define MPUTIM_AR (1<<1) |
| #define MPUTIM_ST (1<<0) |
| |
| /* --------------------------------------------------------------------------- |
| * OMAP1510 GPIO (SHARED) |
| * --------------------------------------------------------------------------- |
| * |
| */ |
| #define GPIO_DATA_INPUT_REG (OMAP1510_GPIO_BASE + 0x0) |
| #define GPIO_DATA_OUTPUT_REG (OMAP1510_GPIO_BASE + 0x4) |
| #define GPIO_DIR_CONTROL_REG (OMAP1510_GPIO_BASE + 0x8) |
| #define GPIO_INT_CONTROL_REG (OMAP1510_GPIO_BASE + 0xc) |
| #define GPIO_INT_MASK_REG (OMAP1510_GPIO_BASE + 0x10) |
| #define GPIO_INT_STATUS_REG (OMAP1510_GPIO_BASE + 0x14) |
| #define GPIO_PIN_CONTROL_REG (OMAP1510_GPIO_BASE + 0x18) |
| |
| |
| /* --------------------------- |
| * OMAP1510 MPUIO (ARM only) |
| *---------------------------- |
| */ |
| #define OMAP1510_MPUIO_BASE 0xFFFB5000 |
| #define MPUIO_DATA_INPUT_REG (OMAP1510_MPUIO_BASE + 0x0) |
| #define MPUIO_DATA_OUTPUT_REG (OMAP1510_MPUIO_BASE + 0x4) |
| #define MPUIO_DIR_CONTROL_REG (OMAP1510_MPUIO_BASE + 0x8) |
| |
| /* --------------------------------------------------------------------------- |
| * OMAP1510 TIPB (only) |
| * --------------------------------------------------------------------------- |
| * |
| */ |
| #define TIPB_PUBLIC_CNTL_BASE 0xfffed300 |
| #define MPU_PUBLIC_TIPB_CNTL_REG (TIPB_PUBLIC_CNTL_BASE + 0x8) |
| #define TIPB_PRIVATE_CNTL_BASE 0xfffeca00 |
| #define MPU_PRIVATE_TIPB_CNTL_REG (TIPB_PRIVATE_CNTL_BASE + 0x8) |
| |
| /* |
| * --------------------------------------------------------------------------- |
| * OMAP1510 Camera Interface |
| * --------------------------------------------------------------------------- |
| */ |
| #define CAMERA_BASE (IO_BASE + 0x6800) |
| #define CAM_CTRLCLOCK_REG (CAMERA_BASE + 0x00) |
| #define CAM_IT_STATUS_REG (CAMERA_BASE + 0x04) |
| #define CAM_MODE_REG (CAMERA_BASE + 0x08) |
| #define CAM_STATUS_REG (CAMERA_BASE + 0x0C) |
| #define CAM_CAMDATA_REG (CAMERA_BASE + 0x10) |
| #define CAM_GPIO_REG (CAMERA_BASE + 0x14) |
| #define CAM_PEAK_CTR_REG (CAMERA_BASE + 0x18) |
| |
| #if 0 |
| #ifndef __ASSEMBLY__ |
| typedef struct { |
| __u32 ctrlclock; |
| __u32 it_status; |
| __u32 mode; |
| __u32 status; |
| __u32 camdata; |
| __u32 gpio; |
| __u32 peak_counter; |
| } camera_regs_t; |
| #endif |
| #endif |
| |
| /* CTRLCLOCK bit shifts */ |
| #define FOSCMOD_BIT 0 |
| #define FOSCMOD_MASK (0x7 << FOSCMOD_BIT) |
| #define FOSCMOD_12MHz 0x0 |
| #define FOSCMOD_6MHz 0x2 |
| #define FOSCMOD_9_6MHz 0x4 |
| #define FOSCMOD_24MHz 0x5 |
| #define FOSCMOD_8MHz 0x6 |
| #define POLCLK (1<<3) |
| #define CAMEXCLK_EN (1<<4) |
| #define MCLK_EN (1<<5) |
| #define DPLL_EN (1<<6) |
| #define LCLK_EN (1<<7) |
| |
| /* IT_STATUS bit shifts */ |
| #define V_UP (1<<0) |
| #define V_DOWN (1<<1) |
| #define H_UP (1<<2) |
| #define H_DOWN (1<<3) |
| #define FIFO_FULL (1<<4) |
| #define DATA_XFER (1<<5) |
| |
| /* MODE bit shifts */ |
| #define CAMOSC (1<<0) |
| #define IMGSIZE_BIT 1 |
| #define IMGSIZE_MASK (0x3 << IMGSIZE_BIT) |
| #define IMGSIZE_CIF (0x0 << IMGSIZE_BIT) /* 352x288 */ |
| #define IMGSIZE_QCIF (0x1 << IMGSIZE_BIT) /* 176x144 */ |
| #define IMGSIZE_VGA (0x2 << IMGSIZE_BIT) /* 640x480 */ |
| #define IMGSIZE_QVGA (0x3 << IMGSIZE_BIT) /* 320x240 */ |
| #define ORDERCAMD (1<<3) |
| #define EN_V_UP (1<<4) |
| #define EN_V_DOWN (1<<5) |
| #define EN_H_UP (1<<6) |
| #define EN_H_DOWN (1<<7) |
| #define EN_DMA (1<<8) |
| #define THRESHOLD (1<<9) |
| #define THRESHOLD_BIT 9 |
| #define THRESHOLD_MASK (0x7f<<9) |
| #define EN_NIRQ (1<<16) |
| #define EN_FIFO_FULL (1<<17) |
| #define RAZ_FIFO (1<<18) |
| |
| /* STATUS bit shifts */ |
| #define VSTATUS (1<<0) |
| #define HSTATUS (1<<1) |
| |
| /* GPIO bit shifts */ |
| #define CAM_RST (1<<0) |
| |
| |
| /********************* |
| * Watchdog timer. |
| *********************/ |
| #define WDTIM_BASE 0xfffec800 |
| #define WDTIM_CONTROL (WDTIM_BASE+0x00) |
| #define WDTIM_LOAD (WDTIM_BASE+0x04) |
| #define WDTIM_READ (WDTIM_BASE+0x04) |
| #define WDTIM_MODE (WDTIM_BASE+0x08) |
| |
| /* Values to write to mode register to disable the watchdog function. */ |
| #define DISABLE_SEQ1 0xF5 |
| #define DISABLE_SEQ2 0xA0 |
| |
| /* WDTIM_CONTROL bit definitions. */ |
| #define WDTIM_CONTROL_ST BIT7 |
| |
| |
| /* --------------------------------------------------------------------------- |
| * Differentiating processor versions for those who care. |
| * --------------------------------------------------------------------------- |
| * |
| */ |
| #define OMAP1509 0 |
| #define OMAP1510 1 |
| |
| #define OMAP1510_ID_CODE_REG 0xfffed404 |
| |
| #ifndef __ASSEMBLY__ |
| int cpu_type(void); |
| #endif |
| |
| /* |
| * EVM Implementation Specifics. |
| * |
| * *** NOTE *** |
| * Any definitions in these files should be prefixed by an identifier - |
| * eg. OMAP1510P1_FLASH0_BASE . |
| * |
| */ |
| #ifdef CONFIG_OMAP_INNOVATOR |
| #include "innovator.h" |
| #endif |
| |
| #ifdef CONFIG_OMAP_1510P1 |
| #include "omap1510p1.h" |
| #endif |
| |
| /*****************************************************************************/ |
| |
| #define CLKGEN_RESET_BASE (0xfffece00) |
| #define ARM_CKCTL (volatile __u16 *)(CLKGEN_RESET_BASE + 0x0) |
| #define ARM_IDLECT1 (volatile __u16 *)(CLKGEN_RESET_BASE + 0x4) |
| #define ARM_IDLECT2 (volatile __u16 *)(CLKGEN_RESET_BASE + 0x8) |
| #define ARM_EWUPCT (volatile __u16 *)(CLKGEN_RESET_BASE + 0xC) |
| #define ARM_RSTCT1 (volatile __u16 *)(CLKGEN_RESET_BASE + 0x10) |
| #define ARM_RSTCT2 (volatile __u16 *)(CLKGEN_RESET_BASE + 0x14) |
| #define ARM_SYSST (volatile __u16 *)(CLKGEN_RESET_BASE + 0x18) |
| |
| |
| #define CK_CLKIN 12 /* MHz */ |
| #define CK_RATEF 1 |
| #define CK_IDLEF 2 |
| #define CK_ENABLEF 4 |
| #define CK_SELECTF 8 |
| #ifndef __ASSEMBLER__ |
| #define CK_DPLL1 ((volatile __u16 *)0xfffecf00) |
| #else |
| #define CK_DPLL1 (0xfffecf00) |
| #endif |
| #define SETARM_IDLE_SHIFT |
| |
| /* ARM_CKCTL bit shifts */ |
| #define PERDIV 0 |
| #define LCDDIV 2 |
| #define ARMDIV 4 |
| #define DSPDIV 6 |
| #define TCDIV 8 |
| #define DSPMMUDIV 10 |
| #define ARM_TIMXO 12 |
| #define EN_DSPCK 13 |
| #define ARM_INTHCK_SEL 14 /* REVISIT -- where is this used? */ |
| |
| #define ARM_CKCTL_RSRVD_BIT15 (1 << 15) |
| #define ARM_CKCTL_ARM_INTHCK_SEL (1 << 14) |
| #define ARM_CKCTL_EN_DSPCK (1 << 13) |
| #define ARM_CKCTL_ARM_TIMXO (1 << 12) |
| #define ARM_CKCTL_DSPMMU_DIV1 (1 << 11) |
| #define ARM_CKCTL_DSPMMU_DIV2 (1 << 10) |
| #define ARM_CKCTL_TCDIV1 (1 << 9) |
| #define ARM_CKCTL_TCDIV2 (1 << 8) |
| #define ARM_CKCTL_DSPDIV1 (1 << 7) |
| #define ARM_CKCTL_DSPDIV0 (1 << 6) |
| #define ARM_CKCTL_ARMDIV1 (1 << 5) |
| #define ARM_CKCTL_ARMDIV0 (1 << 4) |
| #define ARM_CKCTL_LCDDIV1 (1 << 3) |
| #define ARM_CKCTL_LCDDIV0 (1 << 2) |
| #define ARM_CKCTL_PERDIV1 (1 << 1) |
| #define ARM_CKCTL_PERDIV0 (1 << 0) |
| |
| /* ARM_IDLECT1 bit shifts */ |
| #define IDLWDT_ARM 0 |
| #define IDLXORP_ARM 1 |
| #define IDLPER_ARM 2 |
| #define IDLLCD_ARM 3 |
| #define IDLLB_ARM 4 |
| #define IDLHSAB_ARM 5 |
| #define IDLIF_ARM 6 |
| #define IDLDPLL_ARM 7 |
| #define IDLAPI_ARM 8 |
| #define IDLTIM_ARM 9 |
| #define SETARM_IDLE 11 |
| |
| /* ARM_IDLECT2 bit shifts */ |
| #define EN_WDTCK 0 |
| #define EN_XORPCK 1 |
| #define EN_PERCK 2 |
| #define EN_LCDCK 3 |
| #define EN_LBCK 4 |
| #define EN_HSABCK 5 |
| #define EN_APICK 6 |
| #define EN_TIMCK 7 |
| #define DMACK_REQ 8 |
| #define EN_GPIOCK 9 |
| #define EN_LBFREECK 10 |
| |
| #define ARM_RSTCT1_SW_RST (1 << 3) |
| #define ARM_RSTCT1_DSP_RST (1 << 2) |
| #define ARM_RSTCT1_DSP_EN (1 << 1) |
| #define ARM_RSTCT1_ARM_RST (1 << 0) |
| |
| /* ARM_RSTCT2 bit shifts */ |
| #define EN_PER 0 |
| |
| #define ARM_SYSST_RSRVD_BIT15 (1 << 15) |
| #define ARM_SYSST_RSRVD_BIT14 (1 << 14) |
| #define ARM_SYSST_CLOCK_SELECT2 (1 << 13) |
| #define ARM_SYSST_CLOCK_SELECT1 (1 << 12) |
| #define ARM_SYSST_CLOCK_SELECT0 (1 << 11) |
| #define ARM_SYSST_RSRVD_BIT10 (1 << 10) |
| #define ARM_SYSST_RSRVD_BIT9 (1 << 9) |
| #define ARM_SYSST_RSRVD_BIT8 (1 << 8) |
| #define ARM_SYSST_RSRVD_BIT7 (1 << 7) |
| #define ARM_SYSST_IDLE_DSP (1 << 6) |
| #define ARM_SYSST_POR (1 << 5) |
| #define ARM_SYSST_EXT_RST (1 << 4) |
| #define ARM_SYSST_ARM_MCRST (1 << 3) |
| #define ARM_SYSST_ARM_WDRST (1 << 2) |
| #define ARM_SYSST_GLOB_SWRST (1 << 1) |
| #define ARM_SYSST_DSP_WDRST (1 << 0) |
| |
| /* Table 15-23. DPLL Control Registers: */ |
| #define DPLL_CTL_REG (volatile __u16 *)(0xfffecf00) |
| |
| /* Table 15-24. Control Register (CTL_REG): */ |
| |
| #define DPLL_CTL_REG_IOB (1 << 13) |
| #define DPLL_CTL_REG_PLL_MULT Fld(5,0) |
| |
| /*****************************************************************************/ |
| |
| /* OMAP INTERRUPT REGISTERS */ |
| #define IRQ_ITR 0x00 |
| #define IRQ_MIR 0x04 |
| #define IRQ_SIR_IRQ 0x10 |
| #define IRQ_SIR_FIQ 0x14 |
| #define IRQ_CONTROL_REG 0x18 |
| #define IRQ_ISR 0x9c |
| #define IRQ_ILR0 0x1c |
| |
| #define REG_IHL1_MIR (OMAP_IH1_BASE+IRQ_MIR) |
| #define REG_IHL2_MIR (OMAP_IH2_BASE+IRQ_MIR) |
| |
| /* INTERRUPT LEVEL REGISTER BITS */ |
| #define ILR_PRIORITY_MASK (0x3c) |
| #define ILR_PRIORITY_SHIFT (2) |
| #define ILR_LEVEL_TRIGGER (1<<1) |
| #define ILR_FIQ (1<<0) |
| |
| #define IRQ_LEVEL_INT 1 |
| #define IRQ_EDGE_INT 0 |
| |
| /* Macros to access registers */ |
| #define outb(v,p) *(volatile u8 *) (p) = v |
| #define outw(v,p) *(volatile u16 *) (p) = v |
| #define outl(v,p) *(volatile u32 *) (p) = v |
| |
| #define inb(p) *(volatile u8 *) (p) |
| #define inw(p) *(volatile u16 *) (p) |
| #define inl(p) *(volatile u32 *) (p) |
