blob: 8e659f3dde915ad40d2365b1fe1af36a5ca59d6a [file] [log] [blame]
Freescale Alaska MPC8220 board
==============================
TsiChung Liew(Tsi-Chung.Liew@freescale.com)
Created 9/21/04
===========================================
Changed files:
==============
- Makefile added MPC8220 and Alaska8220_config
- MAKEALL added MPC8220 and Alaska8220
- README added CONFIG_MPC8220, Alaska8220_config
- common/cmd_bdinfo.c added board information members for MPC8220
- common/cmd_bootm.c added clocks for MPC8220 in do_bootm_linux()
- include/common.h added CONFIG_MPC8220
- include/asm-ppc/u-boot.h added board information members for MPC8220
- include/asm-ppc/global_data.h added global variables - inp_clk, pci_clk,
vco_clk, pev_clk, flb_clk, and bExtUart
- lib_ppc/board.c added CONFIG_MPC8220 support
- net/eth.c added FEC support for MPC8220
Added files:
============
- board/alaska directory for Alaska MPC8220
- board/alaska/alaska.c Alaska dram and BATs setup
- board/alaska/extserial.c external serial (debug card serial) support
- board/alaska/flash.c Socket (AMD) and Onboard (INTEL) flash support
- board/alaska/serial.c to determine which int/ext serial to use
- board/alaska/Makefile Makefile
- board/alaska/config.mk config make
- board/alaska/u-boot.lds Linker description
- cpu/mpc8220/dma.h multi-channel dma header file
- cpu/mpc8220/dramSetup.h dram setup header file
- cpu/mpc8220/fec.h MPC8220 FEC header file
- cpu/mpc8220/cpu.c cpu specific code
- cpu/mpc8220/cpu_init.c Flexbus ChipSelect and Mux pins setup
- cpu/mpc8220/dramSetup.c MPC8220 DDR SDRAM setup
- cpu/mpc8220/fec.c MPC8220 FEC driver
- cpu/mpc8220/i2c.c MPC8220 I2C driver
- cpu/mpc8220/interrupts.c interrupt support (not enable)
- cpu/mpc8220/loadtask.c load dma
- cpu/mpc8220/speed.c system, pci, flexbus, pev, and cpu clock
- cpu/mpc8220/traps.c exception
- cpu/mpc8220/uart.c MPC8220 UART driver
- cpu/mpc8220/Makefile Makefile
- cpu/mpc8220/config.mk config make
- cpu/mpc8220/fec_dma_task.S MPC8220 FEC multi-channel dma program
- cpu/mpc8220/io.S io functions
- cpu/mpc8220/start.S start up
- include/mpc8220.h
- include/asm-ppc/immap_8220.h
- include/configs/Alaska8220.h
1. SWITCH SETTINGS
==================
1.1 SW1: 0 - Boot from Socket Flash (AMD) or 1 - Onboard Flash (INTEL)
SW2: 0 - Select MPC8220 UART or 1 - Debug Card UART
SW3: unsed
SW4: 0 - 1284 or 1 - FEC1
SW5: 0 - PEV or 1 - FEC2
2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL
===========================================
2.1. For the initial bringup, we adopted a consistent memory scheme between u-boot and
linux kernel, you can customize it based on your system requirements:
DDR: 0x00000000-0x1fffffff (max 512MB)
MBAR: 0xf0000000-0xf0027fff (128KB)
CPLD: 0xf1000000-0xf103ffff (256KB)
FPGA: 0xf2000000-0xf203ffff (256KB)
Flash: 0xfe000000-0xffffffff (max 32MB)
3. DEFINITIONS AND COMPILATION
==============================
3.1 Explanation on NEW definitions in include/configs/alaska8220.h
CONFIG_MPC8220 MPC8220 specific
CONFIG_ALASKA8220 Alaska board specific
CFG_MPC8220_CLKIN Define Alaska Input Clock
CONFIG_PSC_CONSOLE Enable MPC8220 UART
CONFIG_EXTUART_CONSOLE Enable External 16552 UART
CFG_AMD_BOOT To determine the u-boot is booted from AMD or Intel
CFG_MBAR MBAR base address
CFG_DEFAULT_MBAR Reset MBAR base address
3.2 Compilation
export CROSS_COMPILE=cross-compile-prefix
cd u-boot-1-1-x
make distclean
make Alaska8220_config
make
4. SCREEN DUMP
==============
4.1 Alaska MPC8220 board
Boot from AMD (NOTE: May not show exactly the same)
U-Boot 1.1.1 (Sep 22 2004 - 22:14:41)
CPU: MPC8220 (JTAG ID 1640301d) at 300 MHz
Bus 120 MHz, CPU 300 MHz, PCI 30 MHz, VCO 480 MHz
Board: Alaska MPC8220 Evaluation Board
I2C: 93 kHz, ready
DRAM: 256 MB
Reserving 167k for U-Boot at: 0ffd6000
FLASH: 16.5 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FEC ETHERNET
=> flinfo
Bank # 1: INTEL 28F128J3A
Size: 8 MB in 64 Sectors
Sector Start Addresses:
FE000000 FE020000 FE040000 FE060000 FE080000
FE0A0000 FE0C0000 FE0E0000 FE100000 FE120000
FE140000 FE160000 FE180000 FE1A0000 FE1C0000
FE1E0000 FE200000 FE220000 FE240000 FE260000
FE280000 FE2A0000 FE2C0000 FE2E0000 FE300000
FE320000 FE340000 FE360000 FE380000 FE3A0000
FE3C0000 FE3E0000 FE400000 FE420000 FE440000
FE460000 FE480000 FE4A0000 FE4C0000 FE4E0000
FE500000 FE520000 FE540000 FE560000 FE580000
FE5A0000 FE5C0000 FE5E0000 FE600000 FE620000
FE640000 FE660000 FE680000 FE6A0000 FE6C0000
FE6E0000 FE700000 FE720000 FE740000 FE760000
FE780000 FE7A0000 FE7C0000 FE7E0000
Bank # 2: INTEL 28F128J3A
Size: 8 MB in 64 Sectors
Sector Start Addresses:
FE800000 FE820000 FE840000 FE860000 FE880000
FE8A0000 FE8C0000 FE8E0000 FE900000 FE920000
FE940000 FE960000 FE980000 FE9A0000 FE9C0000
FE9E0000 FEA00000 FEA20000 FEA40000 FEA60000
FEA80000 FEAA0000 FEAC0000 FEAE0000 FEB00000
FEB20000 FEB40000 FEB60000 FEB80000 FEBA0000
FEBC0000 FEBE0000 FEC00000 FEC20000 FEC40000
FEC60000 FEC80000 FECA0000 FECC0000 FECE0000
FED00000 FED20000 FED40000 FED60000 FED80000
FEDA0000 FEDC0000 FEDE0000 FEE00000 FEE20000
FEE40000 FEE60000 FEE80000 FEEA0000 FEEC0000
FEEE0000 FEF00000 (RO) FEF20000 (RO) FEF40000 FEF60000
FEF80000 FEFA0000 FEFC0000 FEFE0000 (RO)
Bank # 3: AMD AMD29F040B
Size: 0 MB in 7 Sectors
Sector Start Addresses:
FFF00000 (RO) FFF10000 (RO) FFF20000 (RO) FFF30000 FFF40000
FFF50000 FFF60000
Bank # 4: AMD AMD29F040B
Size: 0 MB in 1 Sectors
Sector Start Addresses:
FFF70000 (RO)
=> bdinfo
memstart = 0xF0009800
memsize = 0x10000000
flashstart = 0xFFF00000
flashsize = 0x01080000
flashoffset = 0x00025000
sramstart = 0xF0020000
sramsize = 0x00008000
bootflags = 0x00000001
intfreq = 300 MHz
busfreq = 120 MHz
inpfreq = 30 MHz
flbfreq = 30 MHz
pcifreq = 30 MHz
vcofreq = 480 MHz
pevfreq = 81 MHz
ethaddr = 00:E0:0C:BC:E0:60
eth1addr = 00:E0:0C:BC:E0:61
IP addr = 192.162.1.2
baudrate = 115200 bps
=> printenv
bootargs=root=/dev/ram rw
bootdelay=5
baudrate=115200
ethaddr=00:e0:0c:bc:e0:60
eth1addr=00:e0:0c:bc:e0:61
ipaddr=192.162.1.2
serverip=192.162.1.1
gatewayip=192.162.1.1
netmask=255.255.255.0
hostname=Alaska
stdin=serial
stdout=serial
stderr=serial
ethact=FEC ETHERNET
Environment size: 268/65532 bytes
=> setenv ipaddr 192.160.1.2
=> setenv serverip 192.160.1.1
=> setenv gatewayip 192.160.1.1
=> saveenv
Saving Environment to Flash...
.
Un-Protected 1 sectors
Erasing Flash...
Erasing sector 0 ... done
Erased 1 sectors
Writing to Flash... done
.
Protected 1 sectors
=> tftp 0x10000 linux.elf
Using FEC ETHERNET device
TFTP from server 192.160.1.1; our IP address is 192.160.1.2; sending through gateway 192.160.1.1
Filename 'linux.elf'.
Load address: 0x10000
Loading: invalid RARP header
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##################################################
done
Bytes transferred = 2917494 (2c8476 hex)
=> bootelf
Loading .text @ 0x00a00000 (23820 bytes)
Loading .data @ 0x00a06000 (2752512 bytes)
Clearing .bss @ 0x00ca6000 (12764 bytes)
## Starting application at 0x00a00000 ...
Collect some entropy from RAM........done
loaded at: 00A00000 00CA91DC
zimage at: 00A06A93 00AD7756
initrd at: 00AD8000 00CA5565
avail ram: 00CAA000 014AA000
Linux/PPC load: ip=off console=ttyS0,115200
Uncompressing Linux...done.
Now booting the kernel
Total memory in system: 256 MB
Memory BAT mapping: BAT2=256Mb, BAT3=0Mb, residual: 0Mb
Linux version 2.4.21-rc1 (r61688@bluesocks.sps.mot.com) (gcc version 3.3.1) #17 Wed Sep 8 11:49:16 CDT 2004
Motorola Alaska port (C) 2003 Motorola, Inc.
CPLD rev 3
CPLD switches 0x1b
Set Pin Mux for FEC1
Set Pin Mux for FEC2
Alaska Pin Multiplexing:
Port Configuration Register 0 = 0
Port Configuration Register 1 = 0
Port Configuration Register 2 = 0
Port Configuration Register 3 = 50000000
Port Configuration Register 3 - PCI = 51400180
Setup Alaska FPGA PIC:
Interrupt Enable Register *(u32) = 0
Interrupt Status Register = 2f0000
Interrupt Enable Register in_be32 = 0
Interrupt Status Register = 2f0000
Interrupt Enable Register in_le32 = 0
Interrupt Status Register = 2f00
Interrupt Enable Register readl = 0
Interrupt Status Register = 2f00
Interrupt Enable Register = 0
Interrupt Status Register = 2f0000
Setup Alaska PCI Controller:
On node 0 totalpages: 65536
zone(0): 65536 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: ip=off console=ttyS0,115200
Using XLB clock (120.00 MHz) to set up decrementer
Calibrating delay loop... 199.88 BogoMIPS
Memory: 254792k available (1476k kernel code, 708k data, 228k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
PCI: (pcibios_init) Global-Hose = 0xc029d000
Scanning bus 00
Fixups for bus 00
Bus scan for 00 returning with max=00
PCI: (pcibios_init) finished pci_scan_bus(hose->first_busno = 0, hose->ops = c01a1a74, hose = c029d000)
PCI: (pcibios_init) PCI Bus Count = 0 =?= Next Bus# = 1
PCI: (pcibios_init@pci_fixup_irqs) finished machine dependent PCI interrupt routing!
PCI: bridge rsrc 81000000..81ffffff (100), parent c01a7f88
PCI: bridge rsrc 84000000..87ffffff (200), parent c01a7fa4
PCI: (pcibios_init) finished allocating and assigning resources!
initDma!
Using 90 DMA buffer descriptors
descUsed f0023600, descriptors f002360c freeSram f0024140
unmask SDMA tasks: 0xf0008018 = 0x6f000000
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
JFFS version 1.0, (C) 1999, 2000 Axis Communications AB
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
pty: 256 Unix98 ptys configured
tracek: Copyright (C) Motorola, 2003.
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xf1001008 (irq = 73) is a ST16650
ttyS01 at 0xf1001010 (irq = 74) is a ST16650
elp-fpanel: Copyright (C) Motorola, 2003.
fpanel: fpanelWait timeout
elp-engine: Copyright (C) Motorola, 2003.
Video disabled due to configuration switch 4
Alpine 1284 driver: Copyright (C) Motorola, 2003.
1284 disabled due to configuration switch 5
Alpine USB driver: Copyright (C) Motorola, 2003.
OK
USB: Descriptor download completed OK
enable_irq(41) unbalanced
enable_irq(75) unbalanced
elp-dmaram: Copyright (C) Motorola, 2003.
Total memory in system: 256 MB
elp_dmaram: offset is 0x10000000, size is 0
Xicor NVRAM driver: Copyright (C) Motorola, 2003.
elp-video: Copyright (C) Motorola, 2003.
Video disabled due to configuration switch 4
elp-pfm: Copyright (C) Motorola, 2003.
paddle: Copyright (C) Motorola, 2001, present.
RAMDISK driver initialized: 16 RAM disks of 12288K size 1024 blocksize
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
init_alaska_mtd: chip probing count 0
cfi_cmdset_0001: Erase suspend on write enabled
Using buffer write method
init_alaska_mtd: bank1, name:ALASKA0, size:16777216bytes
ALASKA flash0: Using Static image partition definition
Creating 3 MTD partitions on "ALASKA0":
0x00000000-0x00280000 : "kernel"
0x00280000-0x00fe0000 : "user"
0x00fe0000-0x01000000 : "signature"
mgt_fec_module_init
mgt_fec_init()
mgt_fec_init
mgt_init_fec_dev(0xc05f6000,0)
dev c05f6000 fec_priv c05f6160 fec f0009000
mgt_init_fec_dev(0xc05f6800,1)
dev c05f6800 fec_priv c05f6960 fec f0009800
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 1845k freed
JFFS: Trying to mount a non-mtd device.
VFS: Mounted root (romfs filesystem) readonly.
Freeing unused kernel memory: 228k init
INIT: version 2.78 booting
INIT: Entering runlevel: 1
"Space, a great big place of unknown stuff." -Dexter, for our MotD.
[01/Jan/1970:00:00:01 +0000] boa: server version Boa/0.94.8.3
[01/Jan/1970:00:00:01 +0000] boa: server built Sep 7 2004 at 17:40:55.
[01/Jan/1970:00:00:01 +0000] boa: starting server pid=28, port 80
Mounting flash filesystem, will take a minute...
/etc/rc: line 30: /dev/lp0: No such devish-2.05b#
sh-2.05b# ifup eth0
client (v0.9.9-pre) started
adapter index 2
adapter hardware address 00:e0:0c:bc:e0:60
execle'ing /usr/share/udhcpc/default.script
/sbin/ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:E0:0C:BC:E0:60
BROADCAST MULTICAST MTU:1500 Metric:1
mgt_fec_open
Rfec request irq
X fec_open: rcv_ring_size 8, xmt_ring_size 8
packmgt_fec_open(): call netif_start_queue()
ets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Base address:0x9000
/sbin/ifconfig eth0 up
entering raw listen mode
Opening raw socket on ifindex 2
adding option 0x35
adding option 0x3d
adding option 0x3c
Sending discover...
Waiting on select...
unrelated/bogus packet
Waiting on select...
oooooh!!! got some!
adding option 0x35
adding option 0x3d
adding option 0x3c
adding option 0x32
adding option 0x36
Sending select for 163.12.48.146...
Waiting on select...
oooooh!!! got some!
Waiting on select...
oooooh!!! got some!
Lease of 163.12.48.146 obtained, lease time 345600
execle'ing /usr/share/udhcpc/default.script
/sbin/ifconfig eth0 163.12.48.146 netmask 255.255.254.0
/sbin/ifconfig eth0 up
deleting routers
/sbin/route del default
/sbin/route add default gw 163.12.49.254 dev eth0
adding dns 163.12.252.230
adding dns 192.55.22.4
adding dns 192.5.249.4
entering none listen mode
sh-2.05b#
5. REPROGRAM U-BOOT
===================
5.1 Reprogram u-boot (boot from AMD)
1. Unprotect the boot sector
=> protect off bank 3
2. Download new u-boot binary file
=> tftp 0x10000 u-boot.bin
3. Erase bootsector (max 7 sectors)
=> erase 0xfff00000 0xfff6ffff
4. Program the u-boot to flash
=> cp.b 0x10000 0xfff00000
5. Reset for the new u-boot to take place
=> reset
5.2 Reprogram u-boot (boot from AMD program at INTEL)
1. Unprotect the boot sector
=> protect off bank 2
2. Download new u-boot binary file
=> tftp 0x10000 u-boot.bin
3. Erase bootsector (max 7 sectors)
=> erase 0xfef00000 0xfefdffff
4. Program the u-boot to flash
=> cp.b 0x10000 0xfef00000
5. Reset for the new u-boot to take place
=> reset
5.3 Reprogram u-boot (boot from INTEL)
1. Unprotect the boot sector
=> protect off bank 4
2. Download new u-boot binary file
=> tftp 0x10000 u-boot.bin
3. Erase bootsector (max 7 sectors)
=> erase 0xfff00000 0xfffdffff
4. Program the u-boot to flash
=> cp.b 0x10000 0xfff00000
5. Reset for the new u-boot to take place
=> reset
5.4 Reprogram u-boot (boot from INTEL program at AMD)
1. Unprotect the boot sector
=> protect off bank 1
2. Download new u-boot binary file
=> tftp 0x10000 u-boot.bin
3. Erase bootsector (max 7 sectors)
=> erase 0xfe080000 0xfe0effff
4. Program the u-boot to flash
=> cp.b 0x10000 0xfe080000
5. Reset for the new u-boot to take place
=> reset