blob: 90eac51e3d4ece119a18c6e9e3593932291cb41b [file] [log] [blame]
'\"
'\" Copyright (c) 1993 The Regents of the University of California.
'\" Copyright (c) 1994-1996 Sun Microsystems, Inc.
'\"
'\" See the file "license.terms" for information on usage and redistribution
'\" of this file, and for a DISCLAIMER OF ALL WARRANTIES.
'\"
'\" RCS: @(#) $Id: AppInit.3,v 1.3 2000/04/14 23:01:48 hobbs Exp $
'\"
'\" The definitions below are for supplemental macros used in Tcl/Tk
'\" manual entries.
'\"
'\" .AP type name in/out ?indent?
'\" Start paragraph describing an argument to a library procedure.
'\" type is type of argument (int, etc.), in/out is either "in", "out",
'\" or "in/out" to describe whether procedure reads or modifies arg,
'\" and indent is equivalent to second arg of .IP (shouldn't ever be
'\" needed; use .AS below instead)
'\"
'\" .AS ?type? ?name?
'\" Give maximum sizes of arguments for setting tab stops. Type and
'\" name are examples of largest possible arguments that will be passed
'\" to .AP later. If args are omitted, default tab stops are used.
'\"
'\" .BS
'\" Start box enclosure. From here until next .BE, everything will be
'\" enclosed in one large box.
'\"
'\" .BE
'\" End of box enclosure.
'\"
'\" .CS
'\" Begin code excerpt.
'\"
'\" .CE
'\" End code excerpt.
'\"
'\" .VS ?version? ?br?
'\" Begin vertical sidebar, for use in marking newly-changed parts
'\" of man pages. The first argument is ignored and used for recording
'\" the version when the .VS was added, so that the sidebars can be
'\" found and removed when they reach a certain age. If another argument
'\" is present, then a line break is forced before starting the sidebar.
'\"
'\" .VE
'\" End of vertical sidebar.
'\"
'\" .DS
'\" Begin an indented unfilled display.
'\"
'\" .DE
'\" End of indented unfilled display.
'\"
'\" .SO
'\" Start of list of standard options for a Tk widget. The
'\" options follow on successive lines, in four columns separated
'\" by tabs.
'\"
'\" .SE
'\" End of list of standard options for a Tk widget.
'\"
'\" .OP cmdName dbName dbClass
'\" Start of description of a specific option. cmdName gives the
'\" option's name as specified in the class command, dbName gives
'\" the option's name in the option database, and dbClass gives
'\" the option's class in the option database.
'\"
'\" .UL arg1 arg2
'\" Print arg1 underlined, then print arg2 normally.
'\"
'\" RCS: @(#) $Id: man.macros,v 1.4 2000/08/25 06:18:32 ericm Exp $
'\"
'\" # Set up traps and other miscellaneous stuff for Tcl/Tk man pages.
.if t .wh -1.3i ^B
.nr ^l \n(.l
.ad b
'\" # Start an argument description
.de AP
.ie !"\\$4"" .TP \\$4
.el \{\
. ie !"\\$2"" .TP \\n()Cu
. el .TP 15
.\}
.ta \\n()Au \\n()Bu
.ie !"\\$3"" \{\
\&\\$1 \\fI\\$2\\fP (\\$3)
.\".b
.\}
.el \{\
.br
.ie !"\\$2"" \{\
\&\\$1 \\fI\\$2\\fP
.\}
.el \{\
\&\\fI\\$1\\fP
.\}
.\}
..
'\" # define tabbing values for .AP
.de AS
.nr )A 10n
.if !"\\$1"" .nr )A \\w'\\$1'u+3n
.nr )B \\n()Au+15n
.\"
.if !"\\$2"" .nr )B \\w'\\$2'u+\\n()Au+3n
.nr )C \\n()Bu+\\w'(in/out)'u+2n
..
.AS Tcl_Interp Tcl_CreateInterp in/out
'\" # BS - start boxed text
'\" # ^y = starting y location
'\" # ^b = 1
.de BS
.br
.mk ^y
.nr ^b 1u
.if n .nf
.if n .ti 0
.if n \l'\\n(.lu\(ul'
.if n .fi
..
'\" # BE - end boxed text (draw box now)
.de BE
.nf
.ti 0
.mk ^t
.ie n \l'\\n(^lu\(ul'
.el \{\
.\" Draw four-sided box normally, but don't draw top of
.\" box if the box started on an earlier page.
.ie !\\n(^b-1 \{\
\h'-1.5n'\L'|\\n(^yu-1v'\l'\\n(^lu+3n\(ul'\L'\\n(^tu+1v-\\n(^yu'\l'|0u-1.5n\(ul'
.\}
.el \}\
\h'-1.5n'\L'|\\n(^yu-1v'\h'\\n(^lu+3n'\L'\\n(^tu+1v-\\n(^yu'\l'|0u-1.5n\(ul'
.\}
.\}
.fi
.br
.nr ^b 0
..
'\" # VS - start vertical sidebar
'\" # ^Y = starting y location
'\" # ^v = 1 (for troff; for nroff this doesn't matter)
.de VS
.if !"\\$2"" .br
.mk ^Y
.ie n 'mc \s12\(br\s0
.el .nr ^v 1u
..
'\" # VE - end of vertical sidebar
.de VE
.ie n 'mc
.el \{\
.ev 2
.nf
.ti 0
.mk ^t
\h'|\\n(^lu+3n'\L'|\\n(^Yu-1v\(bv'\v'\\n(^tu+1v-\\n(^Yu'\h'-|\\n(^lu+3n'
.sp -1
.fi
.ev
.\}
.nr ^v 0
..
'\" # Special macro to handle page bottom: finish off current
'\" # box/sidebar if in box/sidebar mode, then invoked standard
'\" # page bottom macro.
.de ^B
.ev 2
'ti 0
'nf
.mk ^t
.if \\n(^b \{\
.\" Draw three-sided box if this is the box's first page,
.\" draw two sides but no top otherwise.
.ie !\\n(^b-1 \h'-1.5n'\L'|\\n(^yu-1v'\l'\\n(^lu+3n\(ul'\L'\\n(^tu+1v-\\n(^yu'\h'|0u'\c
.el \h'-1.5n'\L'|\\n(^yu-1v'\h'\\n(^lu+3n'\L'\\n(^tu+1v-\\n(^yu'\h'|0u'\c
.\}
.if \\n(^v \{\
.nr ^x \\n(^tu+1v-\\n(^Yu
\kx\h'-\\nxu'\h'|\\n(^lu+3n'\ky\L'-\\n(^xu'\v'\\n(^xu'\h'|0u'\c
.\}
.bp
'fi
.ev
.if \\n(^b \{\
.mk ^y
.nr ^b 2
.\}
.if \\n(^v \{\
.mk ^Y
.\}
..
'\" # DS - begin display
.de DS
.RS
.nf
.sp
..
'\" # DE - end display
.de DE
.fi
.RE
.sp
..
'\" # SO - start of list of standard options
.de SO
.SH "STANDARD OPTIONS"
.LP
.nf
.ta 5.5c 11c
.ft B
..
'\" # SE - end of list of standard options
.de SE
.fi
.ft R
.LP
See the \\fBoptions\\fR manual entry for details on the standard options.
..
'\" # OP - start of full description for a single option
.de OP
.LP
.nf
.ta 4c
Command-Line Name: \\fB\\$1\\fR
Database Name: \\fB\\$2\\fR
Database Class: \\fB\\$3\\fR
.fi
.IP
..
'\" # CS - begin code excerpt
.de CS
.RS
.nf
.ta .25i .5i .75i 1i
..
'\" # CE - end code excerpt
.de CE
.fi
.RE
..
.de UL
\\$1\l'|0\(ul'\\$2
..
.TH Tcl_AppInit 3 7.0 Tcl "Tcl Library Procedures"
.BS
.SH NAME
Tcl_AppInit \- perform application-specific initialization
.SH SYNOPSIS
.nf
\fB#include <tcl.h>\fR
.sp
int
\fBTcl_AppInit\fR(\fIinterp\fR)
.SH ARGUMENTS
.AS Tcl_Interp *interp
.AP Tcl_Interp *interp in
Interpreter for the application.
.BE
.SH DESCRIPTION
.PP
\fBTcl_AppInit\fR is a ``hook'' procedure that is invoked by
the main programs for Tcl applications such as \fBtclsh\fR and \fBwish\fR.
Its purpose is to allow new Tcl applications to be created without
modifying the main programs provided as part of Tcl and Tk.
To create a new application you write a new version of
\fBTcl_AppInit\fR to replace the default version provided by Tcl,
then link your new \fBTcl_AppInit\fR with the Tcl library.
.PP
\fBTcl_AppInit\fR is invoked after by \fBTcl_Main\fR and \fBTk_Main\fR
after their own initialization and before entering the main loop
to process commands.
Here are some examples of things that \fBTcl_AppInit\fR might do:
.IP [1]
Call initialization procedures for various packages used by
the application.
Each initialization procedure adds new commands to \fIinterp\fR
for its package and performs other package-specific initialization.
.IP [2]
Process command-line arguments, which can be accessed from the
Tcl variables \fBargv\fR and \fBargv0\fR in \fIinterp\fR.
.IP [3]
Invoke a startup script to initialize the application.
.LP
\fBTcl_AppInit\fR returns TCL_OK or TCL_ERROR.
If it returns TCL_ERROR then it must leave an error message in
for the interpreter's result; otherwise the result is ignored.
.PP
In addition to \fBTcl_AppInit\fR, your application should also contain
a procedure \fBmain\fR that calls \fBTcl_Main\fR as follows:
.CS
Tcl_Main(argc, argv, Tcl_AppInit);
.CE
The third argument to \fBTcl_Main\fR gives the address of the
application-specific initialization procedure to invoke.
This means that you don't have to use the name \fBTcl_AppInit\fR
for the procedure, but in practice the name is nearly always
\fBTcl_AppInit\fR (in versions before Tcl 7.4 the name \fBTcl_AppInit\fR
was implicit; there was no way to specify the procedure explicitly).
The best way to get started is to make a copy of the file
\fBtclAppInit.c\fR from the Tcl library or source directory.
It already contains a \fBmain\fR procedure and a template for
\fBTcl_AppInit\fR that you can modify for your application.
.SH KEYWORDS
application, argument, command, initialization, interpreter