| /* |
| * ethtool.h: Defines for Linux ethtool. |
| * |
| * Copyright (C) 1998 David S. Miller (davem@redhat.com) |
| * Copyright 2001 Jeff Garzik <jgarzik@pobox.com> |
| * Portions Copyright 2001 Sun Microsystems (thockin@sun.com) |
| * Portions Copyright 2002 Intel (eli.kupermann@intel.com, |
| * christopher.leech@intel.com, |
| * scott.feldman@intel.com) |
| * Portions Copyright (C) Sun Microsystems 2008 |
| */ |
| |
| #ifndef _LINUX_ETHTOOL_H |
| #define _LINUX_ETHTOOL_H |
| |
| #include <linux/types.h> |
| #include <linux/if_ether.h> |
| |
| /* This should work for both 32 and 64 bit userland. */ |
| struct ethtool_cmd { |
| __u32 cmd; |
| __u32 supported; /* Features this interface supports */ |
| __u32 advertising; /* Features this interface advertises */ |
| __u16 speed; /* The forced speed, 10Mb, 100Mb, gigabit */ |
| __u8 duplex; /* Duplex, half or full */ |
| __u8 port; /* Which connector port */ |
| __u8 phy_address; |
| __u8 transceiver; /* Which transceiver to use */ |
| __u8 autoneg; /* Enable or disable autonegotiation */ |
| __u8 mdio_support; |
| __u32 maxtxpkt; /* Tx pkts before generating tx int */ |
| __u32 maxrxpkt; /* Rx pkts before generating rx int */ |
| __u16 speed_hi; |
| __u8 eth_tp_mdix; |
| __u8 reserved2; |
| __u32 lp_advertising; /* Features the link partner advertises */ |
| __u32 reserved[2]; |
| }; |
| |
| static __inline__ void ethtool_cmd_speed_set(struct ethtool_cmd *ep, |
| __u32 speed) |
| { |
| |
| ep->speed = (__u16)speed; |
| ep->speed_hi = (__u16)(speed >> 16); |
| } |
| |
| static __inline__ __u32 ethtool_cmd_speed(struct ethtool_cmd *ep) |
| { |
| return (ep->speed_hi << 16) | ep->speed; |
| } |
| |
| #define ETHTOOL_FWVERS_LEN 32 |
| #define ETHTOOL_BUSINFO_LEN 32 |
| /* these strings are set to whatever the driver author decides... */ |
| struct ethtool_drvinfo { |
| __u32 cmd; |
| char driver[32]; /* driver short name, "tulip", "eepro100" */ |
| char version[32]; /* driver version string */ |
| char fw_version[ETHTOOL_FWVERS_LEN]; /* firmware version string */ |
| char bus_info[ETHTOOL_BUSINFO_LEN]; /* Bus info for this IF. */ |
| /* For PCI devices, use pci_name(pci_dev). */ |
| char reserved1[32]; |
| char reserved2[12]; |
| /* |
| * Some struct members below are filled in |
| * using ops->get_sset_count(). Obtaining |
| * this info from ethtool_drvinfo is now |
| * deprecated; Use ETHTOOL_GSSET_INFO |
| * instead. |
| */ |
| __u32 n_priv_flags; /* number of flags valid in ETHTOOL_GPFLAGS */ |
| __u32 n_stats; /* number of u64's from ETHTOOL_GSTATS */ |
| __u32 testinfo_len; |
| __u32 eedump_len; /* Size of data from ETHTOOL_GEEPROM (bytes) */ |
| __u32 regdump_len; /* Size of data from ETHTOOL_GREGS (bytes) */ |
| }; |
| |
| #define SOPASS_MAX 6 |
| /* wake-on-lan settings */ |
| struct ethtool_wolinfo { |
| __u32 cmd; |
| __u32 supported; |
| __u32 wolopts; |
| __u8 sopass[SOPASS_MAX]; /* SecureOn(tm) password */ |
| }; |
| |
| /* for passing single values */ |
| struct ethtool_value { |
| __u32 cmd; |
| __u32 data; |
| }; |
| |
| /* for passing big chunks of data */ |
| struct ethtool_regs { |
| __u32 cmd; |
| __u32 version; /* driver-specific, indicates different chips/revs */ |
| __u32 len; /* bytes */ |
| __u8 data[0]; |
| }; |
| |
| /* for passing EEPROM chunks */ |
| struct ethtool_eeprom { |
| __u32 cmd; |
| __u32 magic; |
| __u32 offset; /* in bytes */ |
| __u32 len; /* in bytes */ |
| __u8 data[0]; |
| }; |
| |
| /* for configuring coalescing parameters of chip */ |
| struct ethtool_coalesce { |
| __u32 cmd; /* ETHTOOL_{G,S}COALESCE */ |
| |
| /* How many usecs to delay an RX interrupt after |
| * a packet arrives. If 0, only rx_max_coalesced_frames |
| * is used. |
| */ |
| __u32 rx_coalesce_usecs; |
| |
| /* How many packets to delay an RX interrupt after |
| * a packet arrives. If 0, only rx_coalesce_usecs is |
| * used. It is illegal to set both usecs and max frames |
| * to zero as this would cause RX interrupts to never be |
| * generated. |
| */ |
| __u32 rx_max_coalesced_frames; |
| |
| /* Same as above two parameters, except that these values |
| * apply while an IRQ is being serviced by the host. Not |
| * all cards support this feature and the values are ignored |
| * in that case. |
| */ |
| __u32 rx_coalesce_usecs_irq; |
| __u32 rx_max_coalesced_frames_irq; |
| |
| /* How many usecs to delay a TX interrupt after |
| * a packet is sent. If 0, only tx_max_coalesced_frames |
| * is used. |
| */ |
| __u32 tx_coalesce_usecs; |
| |
| /* How many packets to delay a TX interrupt after |
| * a packet is sent. If 0, only tx_coalesce_usecs is |
| * used. It is illegal to set both usecs and max frames |
| * to zero as this would cause TX interrupts to never be |
| * generated. |
| */ |
| __u32 tx_max_coalesced_frames; |
| |
| /* Same as above two parameters, except that these values |
| * apply while an IRQ is being serviced by the host. Not |
| * all cards support this feature and the values are ignored |
| * in that case. |
| */ |
| __u32 tx_coalesce_usecs_irq; |
| __u32 tx_max_coalesced_frames_irq; |
| |
| /* How many usecs to delay in-memory statistics |
| * block updates. Some drivers do not have an in-memory |
| * statistic block, and in such cases this value is ignored. |
| * This value must not be zero. |
| */ |
| __u32 stats_block_coalesce_usecs; |
| |
| /* Adaptive RX/TX coalescing is an algorithm implemented by |
| * some drivers to improve latency under low packet rates and |
| * improve throughput under high packet rates. Some drivers |
| * only implement one of RX or TX adaptive coalescing. Anything |
| * not implemented by the driver causes these values to be |
| * silently ignored. |
| */ |
| __u32 use_adaptive_rx_coalesce; |
| __u32 use_adaptive_tx_coalesce; |
| |
| /* When the packet rate (measured in packets per second) |
| * is below pkt_rate_low, the {rx,tx}_*_low parameters are |
| * used. |
| */ |
| __u32 pkt_rate_low; |
| __u32 rx_coalesce_usecs_low; |
| __u32 rx_max_coalesced_frames_low; |
| __u32 tx_coalesce_usecs_low; |
| __u32 tx_max_coalesced_frames_low; |
| |
| /* When the packet rate is below pkt_rate_high but above |
| * pkt_rate_low (both measured in packets per second) the |
| * normal {rx,tx}_* coalescing parameters are used. |
| */ |
| |
| /* When the packet rate is (measured in packets per second) |
| * is above pkt_rate_high, the {rx,tx}_*_high parameters are |
| * used. |
| */ |
| __u32 pkt_rate_high; |
| __u32 rx_coalesce_usecs_high; |
| __u32 rx_max_coalesced_frames_high; |
| __u32 tx_coalesce_usecs_high; |
| __u32 tx_max_coalesced_frames_high; |
| |
| /* How often to do adaptive coalescing packet rate sampling, |
| * measured in seconds. Must not be zero. |
| */ |
| __u32 rate_sample_interval; |
| }; |
| |
| /* for configuring RX/TX ring parameters */ |
| struct ethtool_ringparam { |
| __u32 cmd; /* ETHTOOL_{G,S}RINGPARAM */ |
| |
| /* Read only attributes. These indicate the maximum number |
| * of pending RX/TX ring entries the driver will allow the |
| * user to set. |
| */ |
| __u32 rx_max_pending; |
| __u32 rx_mini_max_pending; |
| __u32 rx_jumbo_max_pending; |
| __u32 tx_max_pending; |
| |
| /* Values changeable by the user. The valid values are |
| * in the range 1 to the "*_max_pending" counterpart above. |
| */ |
| __u32 rx_pending; |
| __u32 rx_mini_pending; |
| __u32 rx_jumbo_pending; |
| __u32 tx_pending; |
| }; |
| |
| /* for configuring link flow control parameters */ |
| struct ethtool_pauseparam { |
| __u32 cmd; /* ETHTOOL_{G,S}PAUSEPARAM */ |
| |
| /* If the link is being auto-negotiated (via ethtool_cmd.autoneg |
| * being true) the user may set 'autonet' here non-zero to have the |
| * pause parameters be auto-negotiated too. In such a case, the |
| * {rx,tx}_pause values below determine what capabilities are |
| * advertised. |
| * |
| * If 'autoneg' is zero or the link is not being auto-negotiated, |
| * then {rx,tx}_pause force the driver to use/not-use pause |
| * flow control. |
| */ |
| __u32 autoneg; |
| __u32 rx_pause; |
| __u32 tx_pause; |
| }; |
| |
| #define ETH_GSTRING_LEN 32 |
| enum ethtool_stringset { |
| ETH_SS_TEST = 0, |
| ETH_SS_STATS, |
| ETH_SS_PRIV_FLAGS, |
| ETH_SS_NTUPLE_FILTERS, |
| }; |
| |
| /* for passing string sets for data tagging */ |
| struct ethtool_gstrings { |
| __u32 cmd; /* ETHTOOL_GSTRINGS */ |
| __u32 string_set; /* string set id e.c. ETH_SS_TEST, etc*/ |
| __u32 len; /* number of strings in the string set */ |
| __u8 data[0]; |
| }; |
| |
| struct ethtool_sset_info { |
| __u32 cmd; /* ETHTOOL_GSSET_INFO */ |
| __u32 reserved; |
| __u64 sset_mask; /* input: each bit selects an sset to query */ |
| /* output: each bit a returned sset */ |
| __u32 data[0]; /* ETH_SS_xxx count, in order, based on bits |
| in sset_mask. One bit implies one |
| __u32, two bits implies two |
| __u32's, etc. */ |
| }; |
| |
| enum ethtool_test_flags { |
| ETH_TEST_FL_OFFLINE = (1 << 0), /* online / offline */ |
| ETH_TEST_FL_FAILED = (1 << 1), /* test passed / failed */ |
| }; |
| |
| /* for requesting NIC test and getting results*/ |
| struct ethtool_test { |
| __u32 cmd; /* ETHTOOL_TEST */ |
| __u32 flags; /* ETH_TEST_FL_xxx */ |
| __u32 reserved; |
| __u32 len; /* result length, in number of u64 elements */ |
| __u64 data[0]; |
| }; |
| |
| /* for dumping NIC-specific statistics */ |
| struct ethtool_stats { |
| __u32 cmd; /* ETHTOOL_GSTATS */ |
| __u32 n_stats; /* number of u64's being returned */ |
| __u64 data[0]; |
| }; |
| |
| struct ethtool_perm_addr { |
| __u32 cmd; /* ETHTOOL_GPERMADDR */ |
| __u32 size; |
| __u8 data[0]; |
| }; |
| |
| /* boolean flags controlling per-interface behavior characteristics. |
| * When reading, the flag indicates whether or not a certain behavior |
| * is enabled/present. When writing, the flag indicates whether |
| * or not the driver should turn on (set) or off (clear) a behavior. |
| * |
| * Some behaviors may read-only (unconditionally absent or present). |
| * If such is the case, return EINVAL in the set-flags operation if the |
| * flag differs from the read-only value. |
| */ |
| enum ethtool_flags { |
| ETH_FLAG_TXVLAN = (1 << 7), /* TX VLAN offload enabled */ |
| ETH_FLAG_RXVLAN = (1 << 8), /* RX VLAN offload enabled */ |
| ETH_FLAG_LRO = (1 << 15), /* LRO is enabled */ |
| ETH_FLAG_NTUPLE = (1 << 27), /* N-tuple filters enabled */ |
| ETH_FLAG_RXHASH = (1 << 28), |
| }; |
| |
| /* The following structures are for supporting RX network flow |
| * classification and RX n-tuple configuration. Note, all multibyte |
| * fields, e.g., ip4src, ip4dst, psrc, pdst, spi, etc. are expected to |
| * be in network byte order. |
| */ |
| |
| /** |
| * struct ethtool_tcpip4_spec - flow specification for TCP/IPv4 etc. |
| * @ip4src: Source host |
| * @ip4dst: Destination host |
| * @psrc: Source port |
| * @pdst: Destination port |
| * @tos: Type-of-service |
| * |
| * This can be used to specify a TCP/IPv4, UDP/IPv4 or SCTP/IPv4 flow. |
| */ |
| struct ethtool_tcpip4_spec { |
| __be32 ip4src; |
| __be32 ip4dst; |
| __be16 psrc; |
| __be16 pdst; |
| __u8 tos; |
| }; |
| |
| /** |
| * struct ethtool_ah_espip4_spec - flow specification for IPsec/IPv4 |
| * @ip4src: Source host |
| * @ip4dst: Destination host |
| * @spi: Security parameters index |
| * @tos: Type-of-service |
| * |
| * This can be used to specify an IPsec transport or tunnel over IPv4. |
| */ |
| struct ethtool_ah_espip4_spec { |
| __be32 ip4src; |
| __be32 ip4dst; |
| __be32 spi; |
| __u8 tos; |
| }; |
| |
| #define ETH_RX_NFC_IP4 1 |
| |
| /** |
| * struct ethtool_usrip4_spec - general flow specification for IPv4 |
| * @ip4src: Source host |
| * @ip4dst: Destination host |
| * @l4_4_bytes: First 4 bytes of transport (layer 4) header |
| * @tos: Type-of-service |
| * @ip_ver: Value must be %ETH_RX_NFC_IP4; mask must be 0 |
| * @proto: Transport protocol number; mask must be 0 |
| */ |
| struct ethtool_usrip4_spec { |
| __be32 ip4src; |
| __be32 ip4dst; |
| __be32 l4_4_bytes; |
| __u8 tos; |
| __u8 ip_ver; |
| __u8 proto; |
| }; |
| |
| /** |
| * struct ethtool_rx_flow_spec - specification for RX flow filter |
| * @flow_type: Type of match to perform, e.g. %TCP_V4_FLOW |
| * @h_u: Flow fields to match (dependent on @flow_type) |
| * @m_u: Masks for flow field bits to be ignored |
| * @ring_cookie: RX ring/queue index to deliver to, or %RX_CLS_FLOW_DISC |
| * if packets should be discarded |
| * @location: Index of filter in hardware table |
| */ |
| struct ethtool_rx_flow_spec { |
| __u32 flow_type; |
| union { |
| struct ethtool_tcpip4_spec tcp_ip4_spec; |
| struct ethtool_tcpip4_spec udp_ip4_spec; |
| struct ethtool_tcpip4_spec sctp_ip4_spec; |
| struct ethtool_ah_espip4_spec ah_ip4_spec; |
| struct ethtool_ah_espip4_spec esp_ip4_spec; |
| struct ethtool_usrip4_spec usr_ip4_spec; |
| struct ethhdr ether_spec; |
| __u8 hdata[72]; |
| } h_u, m_u; |
| __u64 ring_cookie; |
| __u32 location; |
| }; |
| |
| /** |
| * struct ethtool_rxnfc - command to get or set RX flow classification rules |
| * @cmd: Specific command number - %ETHTOOL_GRXFH, %ETHTOOL_SRXFH, |
| * %ETHTOOL_GRXRINGS, %ETHTOOL_GRXCLSRLCNT, %ETHTOOL_GRXCLSRULE, |
| * %ETHTOOL_GRXCLSRLALL, %ETHTOOL_SRXCLSRLDEL or %ETHTOOL_SRXCLSRLINS |
| * @flow_type: Type of flow to be affected, e.g. %TCP_V4_FLOW |
| * @data: Command-dependent value |
| * @fs: Flow filter specification |
| * @rule_cnt: Number of rules to be affected |
| * @rule_locs: Array of valid rule indices |
| * |
| * For %ETHTOOL_GRXFH and %ETHTOOL_SRXFH, @data is a bitmask indicating |
| * the fields included in the flow hash, e.g. %RXH_IP_SRC. The following |
| * structure fields must not be used. |
| * |
| * For %ETHTOOL_GRXRINGS, @data is set to the number of RX rings/queues |
| * on return. |
| * |
| * For %ETHTOOL_GRXCLSRLCNT, @rule_cnt is set to the number of defined |
| * rules on return. |
| * |
| * For %ETHTOOL_GRXCLSRULE, @fs.@location specifies the index of an |
| * existing filter rule on entry and @fs contains the rule on return. |
| * |
| * For %ETHTOOL_GRXCLSRLALL, @rule_cnt specifies the array size of the |
| * user buffer for @rule_locs on entry. On return, @data is the size |
| * of the filter table and @rule_locs contains the indices of the |
| * defined rules. |
| * |
| * For %ETHTOOL_SRXCLSRLINS, @fs specifies the filter rule to add or |
| * update. @fs.@location specifies the index to use and must not be |
| * ignored. |
| * |
| * For %ETHTOOL_SRXCLSRLDEL, @fs.@location specifies the index of an |
| * existing filter rule on entry. |
| * |
| * Implementation of indexed classification rules generally requires a |
| * TCAM. |
| */ |
| struct ethtool_rxnfc { |
| __u32 cmd; |
| __u32 flow_type; |
| __u64 data; |
| struct ethtool_rx_flow_spec fs; |
| __u32 rule_cnt; |
| __u32 rule_locs[0]; |
| }; |
| |
| /** |
| * struct ethtool_rxfh_indir - command to get or set RX flow hash indirection |
| * @cmd: Specific command number - %ETHTOOL_GRXFHINDIR or %ETHTOOL_SRXFHINDIR |
| * @size: On entry, the array size of the user buffer. On return from |
| * %ETHTOOL_GRXFHINDIR, the array size of the hardware indirection table. |
| * @ring_index: RX ring/queue index for each hash value |
| */ |
| struct ethtool_rxfh_indir { |
| __u32 cmd; |
| __u32 size; |
| __u32 ring_index[0]; |
| }; |
| |
| /** |
| * struct ethtool_rx_ntuple_flow_spec - specification for RX flow filter |
| * @flow_type: Type of match to perform, e.g. %TCP_V4_FLOW |
| * @h_u: Flow field values to match (dependent on @flow_type) |
| * @m_u: Masks for flow field value bits to be ignored |
| * @vlan_tag: VLAN tag to match |
| * @vlan_tag_mask: Mask for VLAN tag bits to be ignored |
| * @data: Driver-dependent data to match |
| * @data_mask: Mask for driver-dependent data bits to be ignored |
| * @action: RX ring/queue index to deliver to (non-negative) or other action |
| * (negative, e.g. %ETHTOOL_RXNTUPLE_ACTION_DROP) |
| * |
| * For flow types %TCP_V4_FLOW, %UDP_V4_FLOW and %SCTP_V4_FLOW, where |
| * a field value and mask are both zero this is treated as if all mask |
| * bits are set i.e. the field is ignored. |
| */ |
| struct ethtool_rx_ntuple_flow_spec { |
| __u32 flow_type; |
| union { |
| struct ethtool_tcpip4_spec tcp_ip4_spec; |
| struct ethtool_tcpip4_spec udp_ip4_spec; |
| struct ethtool_tcpip4_spec sctp_ip4_spec; |
| struct ethtool_ah_espip4_spec ah_ip4_spec; |
| struct ethtool_ah_espip4_spec esp_ip4_spec; |
| struct ethtool_usrip4_spec usr_ip4_spec; |
| struct ethhdr ether_spec; |
| __u8 hdata[72]; |
| } h_u, m_u; |
| |
| __u16 vlan_tag; |
| __u16 vlan_tag_mask; |
| __u64 data; |
| __u64 data_mask; |
| |
| __s32 action; |
| #define ETHTOOL_RXNTUPLE_ACTION_DROP (-1) /* drop packet */ |
| #define ETHTOOL_RXNTUPLE_ACTION_CLEAR (-2) /* clear filter */ |
| }; |
| |
| /** |
| * struct ethtool_rx_ntuple - command to set or clear RX flow filter |
| * @cmd: Command number - %ETHTOOL_SRXNTUPLE |
| * @fs: Flow filter specification |
| */ |
| struct ethtool_rx_ntuple { |
| __u32 cmd; |
| struct ethtool_rx_ntuple_flow_spec fs; |
| }; |
| |
| #define ETHTOOL_FLASH_MAX_FILENAME 128 |
| enum ethtool_flash_op_type { |
| ETHTOOL_FLASH_ALL_REGIONS = 0, |
| }; |
| |
| /* for passing firmware flashing related parameters */ |
| struct ethtool_flash { |
| __u32 cmd; |
| __u32 region; |
| char data[ETHTOOL_FLASH_MAX_FILENAME]; |
| }; |
| |
| |
| /* CMDs currently supported */ |
| #define ETHTOOL_GSET 0x00000001 /* Get settings. */ |
| #define ETHTOOL_SSET 0x00000002 /* Set settings. */ |
| #define ETHTOOL_GDRVINFO 0x00000003 /* Get driver info. */ |
| #define ETHTOOL_GREGS 0x00000004 /* Get NIC registers. */ |
| #define ETHTOOL_GWOL 0x00000005 /* Get wake-on-lan options. */ |
| #define ETHTOOL_SWOL 0x00000006 /* Set wake-on-lan options. */ |
| #define ETHTOOL_GMSGLVL 0x00000007 /* Get driver message level */ |
| #define ETHTOOL_SMSGLVL 0x00000008 /* Set driver msg level. */ |
| #define ETHTOOL_NWAY_RST 0x00000009 /* Restart autonegotiation. */ |
| #define ETHTOOL_GLINK 0x0000000a /* Get link status (ethtool_value) */ |
| #define ETHTOOL_GEEPROM 0x0000000b /* Get EEPROM data */ |
| #define ETHTOOL_SEEPROM 0x0000000c /* Set EEPROM data. */ |
| #define ETHTOOL_GCOALESCE 0x0000000e /* Get coalesce config */ |
| #define ETHTOOL_SCOALESCE 0x0000000f /* Set coalesce config. */ |
| #define ETHTOOL_GRINGPARAM 0x00000010 /* Get ring parameters */ |
| #define ETHTOOL_SRINGPARAM 0x00000011 /* Set ring parameters. */ |
| #define ETHTOOL_GPAUSEPARAM 0x00000012 /* Get pause parameters */ |
| #define ETHTOOL_SPAUSEPARAM 0x00000013 /* Set pause parameters. */ |
| #define ETHTOOL_GRXCSUM 0x00000014 /* Get RX hw csum enable (ethtool_value) */ |
| #define ETHTOOL_SRXCSUM 0x00000015 /* Set RX hw csum enable (ethtool_value) */ |
| #define ETHTOOL_GTXCSUM 0x00000016 /* Get TX hw csum enable (ethtool_value) */ |
| #define ETHTOOL_STXCSUM 0x00000017 /* Set TX hw csum enable (ethtool_value) */ |
| #define ETHTOOL_GSG 0x00000018 /* Get scatter-gather enable |
| * (ethtool_value) */ |
| #define ETHTOOL_SSG 0x00000019 /* Set scatter-gather enable |
| * (ethtool_value). */ |
| #define ETHTOOL_TEST 0x0000001a /* execute NIC self-test. */ |
| #define ETHTOOL_GSTRINGS 0x0000001b /* get specified string set */ |
| #define ETHTOOL_PHYS_ID 0x0000001c /* identify the NIC */ |
| #define ETHTOOL_GSTATS 0x0000001d /* get NIC-specific statistics */ |
| #define ETHTOOL_GTSO 0x0000001e /* Get TSO enable (ethtool_value) */ |
| #define ETHTOOL_STSO 0x0000001f /* Set TSO enable (ethtool_value) */ |
| #define ETHTOOL_GPERMADDR 0x00000020 /* Get permanent hardware address */ |
| #define ETHTOOL_GUFO 0x00000021 /* Get UFO enable (ethtool_value) */ |
| #define ETHTOOL_SUFO 0x00000022 /* Set UFO enable (ethtool_value) */ |
| #define ETHTOOL_GGSO 0x00000023 /* Get GSO enable (ethtool_value) */ |
| #define ETHTOOL_SGSO 0x00000024 /* Set GSO enable (ethtool_value) */ |
| #define ETHTOOL_GFLAGS 0x00000025 /* Get flags bitmap(ethtool_value) */ |
| #define ETHTOOL_SFLAGS 0x00000026 /* Set flags bitmap(ethtool_value) */ |
| #define ETHTOOL_GPFLAGS 0x00000027 /* Get driver-private flags bitmap */ |
| #define ETHTOOL_SPFLAGS 0x00000028 /* Set driver-private flags bitmap */ |
| |
| #define ETHTOOL_GRXFH 0x00000029 /* Get RX flow hash configuration */ |
| #define ETHTOOL_SRXFH 0x0000002a /* Set RX flow hash configuration */ |
| #define ETHTOOL_GGRO 0x0000002b /* Get GRO enable (ethtool_value) */ |
| #define ETHTOOL_SGRO 0x0000002c /* Set GRO enable (ethtool_value) */ |
| #define ETHTOOL_GRXRINGS 0x0000002d /* Get RX rings available for LB */ |
| #define ETHTOOL_GRXCLSRLCNT 0x0000002e /* Get RX class rule count */ |
| #define ETHTOOL_GRXCLSRULE 0x0000002f /* Get RX classification rule */ |
| #define ETHTOOL_GRXCLSRLALL 0x00000030 /* Get all RX classification rule */ |
| #define ETHTOOL_SRXCLSRLDEL 0x00000031 /* Delete RX classification rule */ |
| #define ETHTOOL_SRXCLSRLINS 0x00000032 /* Insert RX classification rule */ |
| #define ETHTOOL_FLASHDEV 0x00000033 /* Flash firmware to device */ |
| #define ETHTOOL_RESET 0x00000034 /* Reset hardware */ |
| #define ETHTOOL_SRXNTUPLE 0x00000035 /* Add an n-tuple filter to device */ |
| #define ETHTOOL_GRXNTUPLE 0x00000036 /* Get n-tuple filters from device */ |
| #define ETHTOOL_GSSET_INFO 0x00000037 /* Get string set info */ |
| #define ETHTOOL_GRXFHINDIR 0x00000038 /* Get RX flow hash indir'n table */ |
| #define ETHTOOL_SRXFHINDIR 0x00000039 /* Set RX flow hash indir'n table */ |
| |
| /* compatibility with older code */ |
| #define SPARC_ETH_GSET ETHTOOL_GSET |
| #define SPARC_ETH_SSET ETHTOOL_SSET |
| |
| /* Indicates what features are supported by the interface. */ |
| #define SUPPORTED_10baseT_Half (1 << 0) |
| #define SUPPORTED_10baseT_Full (1 << 1) |
| #define SUPPORTED_100baseT_Half (1 << 2) |
| #define SUPPORTED_100baseT_Full (1 << 3) |
| #define SUPPORTED_1000baseT_Half (1 << 4) |
| #define SUPPORTED_1000baseT_Full (1 << 5) |
| #define SUPPORTED_Autoneg (1 << 6) |
| #define SUPPORTED_TP (1 << 7) |
| #define SUPPORTED_AUI (1 << 8) |
| #define SUPPORTED_MII (1 << 9) |
| #define SUPPORTED_FIBRE (1 << 10) |
| #define SUPPORTED_BNC (1 << 11) |
| #define SUPPORTED_10000baseT_Full (1 << 12) |
| #define SUPPORTED_Pause (1 << 13) |
| #define SUPPORTED_Asym_Pause (1 << 14) |
| #define SUPPORTED_2500baseX_Full (1 << 15) |
| #define SUPPORTED_Backplane (1 << 16) |
| #define SUPPORTED_1000baseKX_Full (1 << 17) |
| #define SUPPORTED_10000baseKX4_Full (1 << 18) |
| #define SUPPORTED_10000baseKR_Full (1 << 19) |
| #define SUPPORTED_10000baseR_FEC (1 << 20) |
| |
| /* Indicates what features are advertised by the interface. */ |
| #define ADVERTISED_10baseT_Half (1 << 0) |
| #define ADVERTISED_10baseT_Full (1 << 1) |
| #define ADVERTISED_100baseT_Half (1 << 2) |
| #define ADVERTISED_100baseT_Full (1 << 3) |
| #define ADVERTISED_1000baseT_Half (1 << 4) |
| #define ADVERTISED_1000baseT_Full (1 << 5) |
| #define ADVERTISED_Autoneg (1 << 6) |
| #define ADVERTISED_TP (1 << 7) |
| #define ADVERTISED_AUI (1 << 8) |
| #define ADVERTISED_MII (1 << 9) |
| #define ADVERTISED_FIBRE (1 << 10) |
| #define ADVERTISED_BNC (1 << 11) |
| #define ADVERTISED_10000baseT_Full (1 << 12) |
| #define ADVERTISED_Pause (1 << 13) |
| #define ADVERTISED_Asym_Pause (1 << 14) |
| #define ADVERTISED_2500baseX_Full (1 << 15) |
| #define ADVERTISED_Backplane (1 << 16) |
| #define ADVERTISED_1000baseKX_Full (1 << 17) |
| #define ADVERTISED_10000baseKX4_Full (1 << 18) |
| #define ADVERTISED_10000baseKR_Full (1 << 19) |
| #define ADVERTISED_10000baseR_FEC (1 << 20) |
| |
| /* The following are all involved in forcing a particular link |
| * mode for the device for setting things. When getting the |
| * devices settings, these indicate the current mode and whether |
| * it was foced up into this mode or autonegotiated. |
| */ |
| |
| /* The forced speed, 10Mb, 100Mb, gigabit, 2.5Gb, 10GbE. */ |
| #define SPEED_10 10 |
| #define SPEED_100 100 |
| #define SPEED_1000 1000 |
| #define SPEED_2500 2500 |
| #define SPEED_10000 10000 |
| |
| /* Duplex, half or full. */ |
| #define DUPLEX_HALF 0x00 |
| #define DUPLEX_FULL 0x01 |
| |
| /* Which connector port. */ |
| #define PORT_TP 0x00 |
| #define PORT_AUI 0x01 |
| #define PORT_MII 0x02 |
| #define PORT_FIBRE 0x03 |
| #define PORT_BNC 0x04 |
| #define PORT_DA 0x05 |
| #define PORT_NONE 0xef |
| #define PORT_OTHER 0xff |
| |
| /* Which transceiver to use. */ |
| #define XCVR_INTERNAL 0x00 |
| #define XCVR_EXTERNAL 0x01 |
| #define XCVR_DUMMY1 0x02 |
| #define XCVR_DUMMY2 0x03 |
| #define XCVR_DUMMY3 0x04 |
| |
| /* Enable or disable autonegotiation. If this is set to enable, |
| * the forced link modes above are completely ignored. |
| */ |
| #define AUTONEG_DISABLE 0x00 |
| #define AUTONEG_ENABLE 0x01 |
| |
| /* Mode MDI or MDI-X */ |
| #define ETH_TP_MDI_INVALID 0x00 |
| #define ETH_TP_MDI 0x01 |
| #define ETH_TP_MDI_X 0x02 |
| |
| /* Wake-On-Lan options. */ |
| #define WAKE_PHY (1 << 0) |
| #define WAKE_UCAST (1 << 1) |
| #define WAKE_MCAST (1 << 2) |
| #define WAKE_BCAST (1 << 3) |
| #define WAKE_ARP (1 << 4) |
| #define WAKE_MAGIC (1 << 5) |
| #define WAKE_MAGICSECURE (1 << 6) /* only meaningful if WAKE_MAGIC */ |
| |
| /* L2-L4 network traffic flow types */ |
| #define TCP_V4_FLOW 0x01 /* hash or spec (tcp_ip4_spec) */ |
| #define UDP_V4_FLOW 0x02 /* hash or spec (udp_ip4_spec) */ |
| #define SCTP_V4_FLOW 0x03 /* hash or spec (sctp_ip4_spec) */ |
| #define AH_ESP_V4_FLOW 0x04 /* hash only */ |
| #define TCP_V6_FLOW 0x05 /* hash only */ |
| #define UDP_V6_FLOW 0x06 /* hash only */ |
| #define SCTP_V6_FLOW 0x07 /* hash only */ |
| #define AH_ESP_V6_FLOW 0x08 /* hash only */ |
| #define AH_V4_FLOW 0x09 /* hash or spec (ah_ip4_spec) */ |
| #define ESP_V4_FLOW 0x0a /* hash or spec (esp_ip4_spec) */ |
| #define AH_V6_FLOW 0x0b /* hash only */ |
| #define ESP_V6_FLOW 0x0c /* hash only */ |
| #define IP_USER_FLOW 0x0d /* spec only (usr_ip4_spec) */ |
| #define IPV4_FLOW 0x10 /* hash only */ |
| #define IPV6_FLOW 0x11 /* hash only */ |
| #define ETHER_FLOW 0x12 /* spec only (ether_spec) */ |
| |
| /* L3-L4 network traffic flow hash options */ |
| #define RXH_L2DA (1 << 1) |
| #define RXH_VLAN (1 << 2) |
| #define RXH_L3_PROTO (1 << 3) |
| #define RXH_IP_SRC (1 << 4) |
| #define RXH_IP_DST (1 << 5) |
| #define RXH_L4_B_0_1 (1 << 6) /* src port in case of TCP/UDP/SCTP */ |
| #define RXH_L4_B_2_3 (1 << 7) /* dst port in case of TCP/UDP/SCTP */ |
| #define RXH_DISCARD (1 << 31) |
| |
| #define RX_CLS_FLOW_DISC 0xffffffffffffffffULL |
| |
| /* Reset flags */ |
| /* The reset() operation must clear the flags for the components which |
| * were actually reset. On successful return, the flags indicate the |
| * components which were not reset, either because they do not exist |
| * in the hardware or because they cannot be reset independently. The |
| * driver must never reset any components that were not requested. |
| */ |
| enum ethtool_reset_flags { |
| /* These flags represent components dedicated to the interface |
| * the command is addressed to. Shift any flag left by |
| * ETH_RESET_SHARED_SHIFT to reset a shared component of the |
| * same type. |
| */ |
| ETH_RESET_MGMT = 1 << 0, /* Management processor */ |
| ETH_RESET_IRQ = 1 << 1, /* Interrupt requester */ |
| ETH_RESET_DMA = 1 << 2, /* DMA engine */ |
| ETH_RESET_FILTER = 1 << 3, /* Filtering/flow direction */ |
| ETH_RESET_OFFLOAD = 1 << 4, /* Protocol offload */ |
| ETH_RESET_MAC = 1 << 5, /* Media access controller */ |
| ETH_RESET_PHY = 1 << 6, /* Transceiver/PHY */ |
| ETH_RESET_RAM = 1 << 7, /* RAM shared between |
| * multiple components */ |
| |
| ETH_RESET_DEDICATED = 0x0000ffff, /* All components dedicated to |
| * this interface */ |
| ETH_RESET_ALL = 0xffffffff, /* All components used by this |
| * interface, even if shared */ |
| }; |
| #define ETH_RESET_SHARED_SHIFT 16 |
| |
| #endif /* _LINUX_ETHTOOL_H */ |