drivers/staging/et131x/et1310_mac.c

/*
 * Agere Systems Inc.
 * 10/100/1000 Base-T Ethernet Driver for the ET1301 and ET131x series MACs
 *
 * Copyright © 2005 Agere Systems Inc.
 * All rights reserved.
 *   http://www.agere.com
 *
 *------------------------------------------------------------------------------
 *
 * et1310_mac.c - All code and routines pertaining to the MAC
 *
 *------------------------------------------------------------------------------
 *
 * SOFTWARE LICENSE
 *
 * This software is provided subject to the following terms and conditions,
 * which you should read carefully before using the software.  Using this
 * software indicates your acceptance of these terms and conditions.  If you do
 * not agree with these terms and conditions, do not use the software.
 *
 * Copyright © 2005 Agere Systems Inc.
 * All rights reserved.
 *
 * Redistribution and use in source or binary forms, with or without
 * modifications, are permitted provided that the following conditions are met:
 *
 * . Redistributions of source code must retain the above copyright notice, this
 *    list of conditions and the following Disclaimer as comments in the code as
 *    well as in the documentation and/or other materials provided with the
 *    distribution.
 *
 * . Redistributions in binary form must reproduce the above copyright notice,
 *    this list of conditions and the following Disclaimer in the documentation
 *    and/or other materials provided with the distribution.
 *
 * . Neither the name of Agere Systems Inc. nor the names of the contributors
 *    may be used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * Disclaimer
 *
 * THIS SOFTWARE IS PROVIDED “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
 * INCLUDING, BUT NOT LIMITED TO, INFRINGEMENT AND THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  ANY
 * USE, MODIFICATION OR DISTRIBUTION OF THIS SOFTWARE IS SOLELY AT THE USERS OWN
 * RISK. IN NO EVENT SHALL AGERE SYSTEMS INC. OR CONTRIBUTORS BE LIABLE FOR ANY
 * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
 * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
 * ON ANY THEORY OF LIABILITY, INCLUDING, BUT NOT LIMITED TO, CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
 * OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
 * DAMAGE.
 *
 */

#include "et131x_version.h"
#include "et131x_debug.h"
#include "et131x_defs.h"

#include <linux/init.h>
#include <linux/module.h>
#include <linux/types.h>
#include <linux/kernel.h>

#include <linux/sched.h>
#include <linux/ptrace.h>
#include <linux/slab.h>
#include <linux/ctype.h>
#include <linux/string.h>
#include <linux/timer.h>
#include <linux/interrupt.h>
#include <linux/in.h>
#include <linux/delay.h>
#include <asm/io.h>
#include <asm/system.h>
#include <asm/bitops.h>

#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
#include <linux/if_arp.h>
#include <linux/ioport.h>
#include <linux/crc32.h>

#include "et1310_phy.h"
#include "et1310_pm.h"
#include "et1310_jagcore.h"
#include "et1310_mac.h"

#include "et131x_adapter.h"
#include "et131x_initpci.h"

/* Data for debugging facilities */
#ifdef CONFIG_ET131X_DEBUG
extern dbg_info_t *et131x_dbginfo;
#endif /* CONFIG_ET131X_DEBUG */

/**
 * ConfigMacRegs1 - Initialize the first part of MAC regs
 * @pAdpater: pointer to our adapter structure
 */
void ConfigMACRegs1(struct et131x_adapter *pAdapter)
{
	struct _MAC_t __iomem *pMac = &pAdapter->CSRAddress->mac;
	MAC_STATION_ADDR1_t station1;
	MAC_STATION_ADDR2_t station2;
	MAC_IPG_t ipg;
	MAC_HFDP_t hfdp;
	MII_MGMT_CFG_t mii_mgmt_cfg;

	DBG_ENTER(et131x_dbginfo);

	/* First we need to reset everything.  Write to MAC configuration
	 * register 1 to perform reset.
	 */
	writel(0xC00F0000, &pMac->cfg1.value);

	/* Next lets configure the MAC Inter-packet gap register */
	ipg.bits.non_B2B_ipg_1 = 0x38;		// 58d
	ipg.bits.non_B2B_ipg_2 = 0x58;		// 88d
	ipg.bits.min_ifg_enforce = 0x50;	// 80d
	ipg.bits.B2B_ipg = 0x60;		// 96d
	writel(ipg.value, &pMac->ipg.value);

	/* Next lets configure the MAC Half Duplex register */
	hfdp.bits.alt_beb_trunc = 0xA;
	hfdp.bits.alt_beb_enable = 0x0;
	hfdp.bits.bp_no_backoff = 0x0;
	hfdp.bits.no_backoff = 0x0;
	hfdp.bits.excess_defer = 0x1;
	hfdp.bits.rexmit_max = 0xF;
	hfdp.bits.coll_window = 0x37;		// 55d
	writel(hfdp.value, &pMac->hfdp.value);

	/* Next lets configure the MAC Interface Control register */
	writel(0, &pMac->if_ctrl.value);

	/* Let's move on to setting up the mii managment configuration */
	mii_mgmt_cfg.bits.reset_mii_mgmt = 0;
	mii_mgmt_cfg.bits.scan_auto_incremt = 0;
	mii_mgmt_cfg.bits.preamble_suppress = 0;
	mii_mgmt_cfg.bits.mgmt_clk_reset = 0x7;
	writel(mii_mgmt_cfg.value, &pMac->mii_mgmt_cfg.value);

	/* Next lets configure the MAC Station Address register.  These
	 * values are read from the EEPROM during initialization and stored
	 * in the adapter structure.  We write what is stored in the adapter
	 * structure to the MAC Station Address registers high and low.  This
	 * station address is used for generating and checking pause control
	 * packets.
	 */
	station2.bits.Octet1 = pAdapter->CurrentAddress[0];
	station2.bits.Octet2 = pAdapter->CurrentAddress[1];
	station1.bits.Octet3 = pAdapter->CurrentAddress[2];
	station1.bits.Octet4 = pAdapter->CurrentAddress[3];
	station1.bits.Octet5 = pAdapter->CurrentAddress[4];
	station1.bits.Octet6 = pAdapter->CurrentAddress[5];
	writel(station1.value, &pMac->station_addr_1.value);
	writel(station2.value, &pMac->station_addr_2.value);

	/* Max ethernet packet in bytes that will passed by the mac without
	 * being truncated.  Allow the MAC to pass 4 more than our max packet
	 * size.  This is 4 for the Ethernet CRC.
	 *
	 * Packets larger than (RegistryJumboPacket) that do not contain a
	 * VLAN ID will be dropped by the Rx function.
	 */
	writel(pAdapter->RegistryJumboPacket + 4, &pMac->max_fm_len.value);

	/* clear out MAC config reset */
	writel(0, &pMac->cfg1.value);

	DBG_LEAVE(et131x_dbginfo);
}

/**
 * ConfigMacRegs2 - Initialize the second part of MAC regs
 * @pAdpater: pointer to our adapter structure
 */
void ConfigMACRegs2(struct et131x_adapter *pAdapter)
{
	int32_t delay = 0;
	struct _MAC_t __iomem *pMac = &pAdapter->CSRAddress->mac;
	MAC_CFG1_t cfg1;
	MAC_CFG2_t cfg2;
	MAC_IF_CTRL_t ifctrl;
	TXMAC_CTL_t ctl;

	DBG_ENTER(et131x_dbginfo);

	ctl.value = readl(&pAdapter->CSRAddress->txmac.ctl.value);
	cfg1.value = readl(&pMac->cfg1.value);
	cfg2.value = readl(&pMac->cfg2.value);
	ifctrl.value = readl(&pMac->if_ctrl.value);

	if (pAdapter->uiLinkSpeed == TRUEPHY_SPEED_1000MBPS) {
		cfg2.bits.if_mode = 0x2;
		ifctrl.bits.phy_mode = 0x0;
	} else {
		cfg2.bits.if_mode = 0x1;
		ifctrl.bits.phy_mode = 0x1;
	}

	/* We need to enable Rx/Tx */
	cfg1.bits.rx_enable = 0x1;
	cfg1.bits.tx_enable = 0x1;

	/* Set up flow control */
	cfg1.bits.tx_flow = 0x1;

	if ((pAdapter->FlowControl == RxOnly) ||
	    (pAdapter->FlowControl == Both)) {
		cfg1.bits.rx_flow = 0x1;
	} else {
		cfg1.bits.rx_flow = 0x0;
	}

	/* Initialize loop back to off */
	cfg1.bits.loop_back = 0;

	writel(cfg1.value, &pMac->cfg1.value);

	/* Now we need to initialize the MAC Configuration 2 register */
	cfg2.bits.preamble_len = 0x7;
	cfg2.bits.huge_frame = 0x0;
	/* LENGTH FIELD CHECKING bit4: Set this bit to cause the MAC to check
	 * the frame's length field to ensure it matches the actual data
	 * field length. Clear this bit if no length field checking is
	 * desired. Its default is 0.
	 */
	cfg2.bits.len_check = 0x1;

	if (pAdapter->RegistryPhyLoopbk == false) {
		cfg2.bits.pad_crc = 0x1;
		cfg2.bits.crc_enable = 0x1;
	} else {
		cfg2.bits.pad_crc = 0;
		cfg2.bits.crc_enable = 0;
	}

	/* 1 - full duplex, 0 - half-duplex */
	cfg2.bits.full_duplex = pAdapter->uiDuplexMode;
	ifctrl.bits.ghd_mode = !pAdapter->uiDuplexMode;

	writel(ifctrl.value, &pMac->if_ctrl.value);
	writel(cfg2.value, &pMac->cfg2.value);

	do {
		udelay(10);
		delay++;
		cfg1.value = readl(&pMac->cfg1.value);
	} while ((!cfg1.bits.syncd_rx_en ||
		  !cfg1.bits.syncd_tx_en) &&
		 delay < 100);

	if (delay == 100) {
		DBG_ERROR(et131x_dbginfo,
			  "Syncd bits did not respond correctly cfg1 word 0x%08x\n",
			  cfg1.value);
	}

	DBG_TRACE(et131x_dbginfo,
		  "Speed %d, Dup %d, CFG1 0x%08x, CFG2 0x%08x, if_ctrl 0x%08x\n",
		  pAdapter->uiLinkSpeed, pAdapter->uiDuplexMode,
		  readl(&pMac->cfg1.value), readl(&pMac->cfg2.value),
		  readl(&pMac->if_ctrl.value));

	/* Enable TXMAC */
	ctl.bits.txmac_en = 0x1;
	ctl.bits.fc_disable = 0x1;
	writel(ctl.value, &pAdapter->CSRAddress->txmac.ctl.value);

	/* Ready to start the RXDMA/TXDMA engine */
	if (!MP_TEST_FLAG(pAdapter, fMP_ADAPTER_LOWER_POWER)) {
		et131x_rx_dma_enable(pAdapter);
		et131x_tx_dma_enable(pAdapter);
	} else {
		DBG_WARNING(et131x_dbginfo,
			    "Didn't enable Rx/Tx due to low-power mode\n");
	}

	DBG_LEAVE(et131x_dbginfo);
}

void ConfigRxMacRegs(struct et131x_adapter *pAdapter)
{
	struct _RXMAC_t __iomem *pRxMac = &pAdapter->CSRAddress->rxmac;
	RXMAC_WOL_SA_LO_t sa_lo;
	RXMAC_WOL_SA_HI_t sa_hi;
	RXMAC_PF_CTRL_t pf_ctrl = { 0 };

	DBG_ENTER(et131x_dbginfo);

	/* Disable the MAC while it is being configured (also disable WOL) */
	writel(0x8, &pRxMac->ctrl.value);

	/* Initialize WOL to disabled. */
	writel(0, &pRxMac->crc0.value);
	writel(0, &pRxMac->crc12.value);
	writel(0, &pRxMac->crc34.value);

	/* We need to set the WOL mask0 - mask4 next.  We initialize it to
	 * its default Values of 0x00000000 because there are not WOL masks
	 * as of this time.
	 */
	writel(0, &pRxMac->mask0_word0);
	writel(0, &pRxMac->mask0_word1);
	writel(0, &pRxMac->mask0_word2);
	writel(0, &pRxMac->mask0_word3);

	writel(0, &pRxMac->mask1_word0);
	writel(0, &pRxMac->mask1_word1);
	writel(0, &pRxMac->mask1_word2);
	writel(0, &pRxMac->mask1_word3);

	writel(0, &pRxMac->mask2_word0);
	writel(0, &pRxMac->mask2_word1);
	writel(0, &pRxMac->mask2_word2);
	writel(0, &pRxMac->mask2_word3);

	writel(0, &pRxMac->mask3_word0);
	writel(0, &pRxMac->mask3_word1);
	writel(0, &pRxMac->mask3_word2);
	writel(0, &pRxMac->mask3_word3);

	writel(0, &pRxMac->mask4_word0);
	writel(0, &pRxMac->mask4_word1);
	writel(0, &pRxMac->mask4_word2);
	writel(0, &pRxMac->mask4_word3);

	/* Lets setup the WOL Source Address */
	sa_lo.bits.sa3 = pAdapter->CurrentAddress[2];
	sa_lo.bits.sa4 = pAdapter->CurrentAddress[3];
	sa_lo.bits.sa5 = pAdapter->CurrentAddress[4];
	sa_lo.bits.sa6 = pAdapter->CurrentAddress[5];
	writel(sa_lo.value, &pRxMac->sa_lo.value);

	sa_hi.bits.sa1 = pAdapter->CurrentAddress[0];
	sa_hi.bits.sa2 = pAdapter->CurrentAddress[1];
	writel(sa_hi.value, &pRxMac->sa_hi.value);

	/* Disable all Packet Filtering */
	writel(0, &pRxMac->pf_ctrl.value);

	/* Let's initialize the Unicast Packet filtering address */
	if (pAdapter->PacketFilter & ET131X_PACKET_TYPE_DIRECTED) {
		SetupDeviceForUnicast(pAdapter);
		pf_ctrl.bits.filter_uni_en = 1;
	} else {
		writel(0, &pRxMac->uni_pf_addr1.value);
		writel(0, &pRxMac->uni_pf_addr2.value);
		writel(0, &pRxMac->uni_pf_addr3.value);
	}

	/* Let's initialize the Multicast hash */
	if (pAdapter->PacketFilter & ET131X_PACKET_TYPE_ALL_MULTICAST) {
		pf_ctrl.bits.filter_multi_en = 0;
	} else {
		pf_ctrl.bits.filter_multi_en = 1;
		SetupDeviceForMulticast(pAdapter);
	}

	/* Runt packet filtering.  Didn't work in version A silicon. */
	pf_ctrl.bits.min_pkt_size = NIC_MIN_PACKET_SIZE + 4;
	pf_ctrl.bits.filter_frag_en = 1;

	if (pAdapter->RegistryJumboPacket > 8192) {
		RXMAC_MCIF_CTRL_MAX_SEG_t mcif_ctrl_max_seg;

		/* In order to transmit jumbo packets greater than 8k, the
		 * FIFO between RxMAC and RxDMA needs to be reduced in size
		 * to (16k - Jumbo packet size).  In order to implement this,
		 * we must use "cut through" mode in the RxMAC, which chops
		 * packets down into segments which are (max_size * 16).  In
		 * this case we selected 256 bytes, since this is the size of
		 * the PCI-Express TLP's that the 1310 uses.
		 */
		mcif_ctrl_max_seg.bits.seg_en = 0x1;
		mcif_ctrl_max_seg.bits.fc_en = 0x0;
		mcif_ctrl_max_seg.bits.max_size = 0x10;

		writel(mcif_ctrl_max_seg.value,
		       &pRxMac->mcif_ctrl_max_seg.value);
	} else {
		writel(0, &pRxMac->mcif_ctrl_max_seg.value);
	}

	/* Initialize the MCIF water marks */
	writel(0, &pRxMac->mcif_water_mark.value);

	/*  Initialize the MIF control */
	writel(0, &pRxMac->mif_ctrl.value);

	/* Initialize the Space Available Register */
	writel(0, &pRxMac->space_avail.value);

	/* Initialize the the mif_ctrl register
	 * bit 3:  Receive code error. One or more nibbles were signaled as
	 *	   errors  during the reception of the packet.  Clear this
	 *	   bit in Gigabit, set it in 100Mbit.  This was derived
	 *	   experimentally at UNH.
	 * bit 4:  Receive CRC error. The packet's CRC did not match the
	 *	   internally generated CRC.
	 * bit 5:  Receive length check error. Indicates that frame length
	 *	   field value in the packet does not match the actual data
	 *	   byte length and is not a type field.
	 * bit 16: Receive frame truncated.
	 * bit 17: Drop packet enable
	 */
	if (pAdapter->uiLinkSpeed == TRUEPHY_SPEED_100MBPS) {
		writel(0x30038, &pRxMac->mif_ctrl.value);
	} else {
		writel(0x30030, &pRxMac->mif_ctrl.value);
	}

	/* Finally we initialize RxMac to be enabled & WOL disabled.  Packet
	 * filter is always enabled since it is where the runt packets are
	 * supposed to be dropped.  For version A silicon, runt packet
	 * dropping doesn't work, so it is disabled in the pf_ctrl register,
	 * but we still leave the packet filter on.
	 */
	writel(pf_ctrl.value, &pRxMac->pf_ctrl.value);
	writel(0x9, &pRxMac->ctrl.value);

	DBG_LEAVE(et131x_dbginfo);
}

void ConfigTxMacRegs(struct et131x_adapter *pAdapter)
{
	struct _TXMAC_t __iomem *pTxMac = &pAdapter->CSRAddress->txmac;
	TXMAC_CF_PARAM_t Local;

	DBG_ENTER(et131x_dbginfo);

	/* We need to update the Control Frame Parameters
	 * cfpt - control frame pause timer set to 64 (0x40)
	 * cfep - control frame extended pause timer set to 0x0
	 */
	if (pAdapter->FlowControl == None) {
		writel(0, &pTxMac->cf_param.value);
	} else {
		Local.bits.cfpt = 0x40;
		Local.bits.cfep = 0x0;
		writel(Local.value, &pTxMac->cf_param.value);
	}

	DBG_LEAVE(et131x_dbginfo);
}

void ConfigMacStatRegs(struct et131x_adapter *pAdapter)
{
	struct _MAC_STAT_t __iomem *pDevMacStat =
		&pAdapter->CSRAddress->macStat;

	DBG_ENTER(et131x_dbginfo);

	/* Next we need to initialize all the MAC_STAT registers to zero on
	 * the device.
	 */
	writel(0, &pDevMacStat->RFcs);
	writel(0, &pDevMacStat->RAln);
	writel(0, &pDevMacStat->RFlr);
	writel(0, &pDevMacStat->RDrp);
	writel(0, &pDevMacStat->RCde);
	writel(0, &pDevMacStat->ROvr);
	writel(0, &pDevMacStat->RFrg);

	writel(0, &pDevMacStat->TScl);
	writel(0, &pDevMacStat->TDfr);
	writel(0, &pDevMacStat->TMcl);
	writel(0, &pDevMacStat->TLcl);
	writel(0, &pDevMacStat->TNcl);
	writel(0, &pDevMacStat->TOvr);
	writel(0, &pDevMacStat->TUnd);

	/* Unmask any counters that we want to track the overflow of.
	 * Initially this will be all counters.  It may become clear later
	 * that we do not need to track all counters.
	 */
	{
		MAC_STAT_REG_1_t Carry1M = { 0xffffffff };

		Carry1M.bits.rdrp = 0;
		Carry1M.bits.rjbr = 1;
		Carry1M.bits.rfrg = 0;
		Carry1M.bits.rovr = 0;
		Carry1M.bits.rund = 1;
		Carry1M.bits.rcse = 1;
		Carry1M.bits.rcde = 0;
		Carry1M.bits.rflr = 0;
		Carry1M.bits.raln = 0;
		Carry1M.bits.rxuo = 1;
		Carry1M.bits.rxpf = 1;
		Carry1M.bits.rxcf = 1;
		Carry1M.bits.rbca = 1;
		Carry1M.bits.rmca = 1;
		Carry1M.bits.rfcs = 0;
		Carry1M.bits.rpkt = 1;
		Carry1M.bits.rbyt = 1;
		Carry1M.bits.trmgv = 1;
		Carry1M.bits.trmax = 1;
		Carry1M.bits.tr1k = 1;
		Carry1M.bits.tr511 = 1;
		Carry1M.bits.tr255 = 1;
		Carry1M.bits.tr127 = 1;
		Carry1M.bits.tr64 = 1;

		writel(Carry1M.value, &pDevMacStat->Carry1M.value);
	}

	{
		MAC_STAT_REG_2_t Carry2M = { 0xffffffff };

		Carry2M.bits.tdrp = 1;
		Carry2M.bits.tpfh = 1;
		Carry2M.bits.tncl = 0;
		Carry2M.bits.txcl = 1;
		Carry2M.bits.tlcl = 0;
		Carry2M.bits.tmcl = 0;
		Carry2M.bits.tscl = 0;
		Carry2M.bits.tedf = 1;
		Carry2M.bits.tdfr = 0;
		Carry2M.bits.txpf = 1;
		Carry2M.bits.tbca = 1;
		Carry2M.bits.tmca = 1;
		Carry2M.bits.tpkt = 1;
		Carry2M.bits.tbyt = 1;
		Carry2M.bits.tfrg = 1;
		Carry2M.bits.tund = 0;
		Carry2M.bits.tovr = 0;
		Carry2M.bits.txcf = 1;
		Carry2M.bits.tfcs = 1;
		Carry2M.bits.tjbr = 1;

		writel(Carry2M.value, &pDevMacStat->Carry2M.value);
	}

	DBG_LEAVE(et131x_dbginfo);
}

void ConfigFlowControl(struct et131x_adapter * pAdapter)
{
	if (pAdapter->uiDuplexMode == 0) {
		pAdapter->FlowControl = None;
	} else {
		char RemotePause, RemoteAsyncPause;

		ET1310_PhyAccessMiBit(pAdapter,
				      TRUEPHY_BIT_READ, 5, 10, &RemotePause);
		ET1310_PhyAccessMiBit(pAdapter,
				      TRUEPHY_BIT_READ, 5, 11,
				      &RemoteAsyncPause);

		if ((RemotePause == TRUEPHY_BIT_SET) &&
		    (RemoteAsyncPause == TRUEPHY_BIT_SET)) {
			pAdapter->FlowControl = pAdapter->RegistryFlowControl;
		} else if ((RemotePause == TRUEPHY_BIT_SET) &&
			   (RemoteAsyncPause == TRUEPHY_BIT_CLEAR)) {
			if (pAdapter->RegistryFlowControl == Both) {
				pAdapter->FlowControl = Both;
			} else {
				pAdapter->FlowControl = None;
			}
		} else if ((RemotePause == TRUEPHY_BIT_CLEAR) &&
			   (RemoteAsyncPause == TRUEPHY_BIT_CLEAR)) {
			pAdapter->FlowControl = None;
		} else {/* if (RemotePause == TRUEPHY_CLEAR_BIT &&
			       RemoteAsyncPause == TRUEPHY_SET_BIT) */
			if (pAdapter->RegistryFlowControl == Both) {
				pAdapter->FlowControl = RxOnly;
			} else {
				pAdapter->FlowControl = None;
			}
		}
	}
}

/**
 * UpdateMacStatHostCounters - Update the local copy of the statistics
 * @pAdapter: pointer to the adapter structure
 */
void UpdateMacStatHostCounters(struct et131x_adapter *pAdapter)
{
	struct _ce_stats_t *stats = &pAdapter->Stats;
	struct _MAC_STAT_t __iomem *pDevMacStat =
		&pAdapter->CSRAddress->macStat;

	stats->collisions += readl(&pDevMacStat->TNcl);
	stats->first_collision += readl(&pDevMacStat->TScl);
	stats->tx_deferred += readl(&pDevMacStat->TDfr);
	stats->excessive_collisions += readl(&pDevMacStat->TMcl);
	stats->late_collisions += readl(&pDevMacStat->TLcl);
	stats->tx_uflo += readl(&pDevMacStat->TUnd);
	stats->max_pkt_error += readl(&pDevMacStat->TOvr);

	stats->alignment_err += readl(&pDevMacStat->RAln);
	stats->crc_err += readl(&pDevMacStat->RCde);
	stats->norcvbuf += readl(&pDevMacStat->RDrp);
	stats->rx_ov_flow += readl(&pDevMacStat->ROvr);
	stats->code_violations += readl(&pDevMacStat->RFcs);
	stats->length_err += readl(&pDevMacStat->RFlr);

	stats->other_errors += readl(&pDevMacStat->RFrg);
}

/**
 * HandleMacStatInterrupt
 * @pAdapter: pointer to the adapter structure
 *
 * One of the MACSTAT counters has wrapped.  Update the local copy of
 * the statistics held in the adapter structure, checking the "wrap"
 * bit for each counter.
 */
void HandleMacStatInterrupt(struct et131x_adapter *pAdapter)
{
	MAC_STAT_REG_1_t Carry1;
	MAC_STAT_REG_2_t Carry2;

	DBG_ENTER(et131x_dbginfo);

	/* Read the interrupt bits from the register(s).  These are Clear On
	 * Write.
	 */
	Carry1.value = readl(&pAdapter->CSRAddress->macStat.Carry1.value);
	Carry2.value = readl(&pAdapter->CSRAddress->macStat.Carry2.value);

	writel(Carry1.value, &pAdapter->CSRAddress->macStat.Carry1.value);
	writel(Carry2.value, &pAdapter->CSRAddress->macStat.Carry2.value);

	/* We need to do update the host copy of all the MAC_STAT counters.
	 * For each counter, check it's overflow bit.  If the overflow bit is
	 * set, then increment the host version of the count by one complete
	 * revolution of the counter.  This routine is called when the counter
	 * block indicates that one of the counters has wrapped.
	 */
	if (Carry1.bits.rfcs) {
		pAdapter->Stats.code_violations += COUNTER_WRAP_16_BIT;
	}
	if (Carry1.bits.raln) {
		pAdapter->Stats.alignment_err += COUNTER_WRAP_12_BIT;
	}
	if (Carry1.bits.rflr) {
		pAdapter->Stats.length_err += COUNTER_WRAP_16_BIT;
	}
	if (Carry1.bits.rfrg) {
		pAdapter->Stats.other_errors += COUNTER_WRAP_16_BIT;
	}
	if (Carry1.bits.rcde) {
		pAdapter->Stats.crc_err += COUNTER_WRAP_16_BIT;
	}
	if (Carry1.bits.rovr) {
		pAdapter->Stats.rx_ov_flow += COUNTER_WRAP_16_BIT;
	}
	if (Carry1.bits.rdrp) {
		pAdapter->Stats.norcvbuf += COUNTER_WRAP_16_BIT;
	}
	if (Carry2.bits.tovr) {
		pAdapter->Stats.max_pkt_error += COUNTER_WRAP_12_BIT;
	}
	if (Carry2.bits.tund) {
		pAdapter->Stats.tx_uflo += COUNTER_WRAP_12_BIT;
	}
	if (Carry2.bits.tscl) {
		pAdapter->Stats.first_collision += COUNTER_WRAP_12_BIT;
	}
	if (Carry2.bits.tdfr) {
		pAdapter->Stats.tx_deferred += COUNTER_WRAP_12_BIT;
	}
	if (Carry2.bits.tmcl) {
		pAdapter->Stats.excessive_collisions += COUNTER_WRAP_12_BIT;
	}
	if (Carry2.bits.tlcl) {
		pAdapter->Stats.late_collisions += COUNTER_WRAP_12_BIT;
	}
	if (Carry2.bits.tncl) {
		pAdapter->Stats.collisions += COUNTER_WRAP_12_BIT;
	}

	DBG_LEAVE(et131x_dbginfo);
}

void SetupDeviceForMulticast(struct et131x_adapter *pAdapter)
{
	struct _RXMAC_t __iomem *rxmac = &pAdapter->CSRAddress->rxmac;
	uint32_t nIndex;
	uint32_t result;
	uint32_t hash1 = 0;
	uint32_t hash2 = 0;
	uint32_t hash3 = 0;
	uint32_t hash4 = 0;
	PM_CSR_t pm_csr;

	DBG_ENTER(et131x_dbginfo);

	/* If ET131X_PACKET_TYPE_MULTICAST is specified, then we provision
	 * the multi-cast LIST.  If it is NOT specified, (and "ALL" is not
	 * specified) then we should pass NO multi-cast addresses to the
	 * driver.
	 */
	if (pAdapter->PacketFilter & ET131X_PACKET_TYPE_MULTICAST) {
		DBG_VERBOSE(et131x_dbginfo,
			    "MULTICAST flag is set, MCCount: %d\n",
			    pAdapter->MCAddressCount);

		/* Loop through our multicast array and set up the device */
		for (nIndex = 0; nIndex < pAdapter->MCAddressCount; nIndex++) {
			DBG_VERBOSE(et131x_dbginfo,
				    "MCList[%d]: %02x:%02x:%02x:%02x:%02x:%02x\n",
				    nIndex,
				    pAdapter->MCList[nIndex][0],
				    pAdapter->MCList[nIndex][1],
				    pAdapter->MCList[nIndex][2],
				    pAdapter->MCList[nIndex][3],
				    pAdapter->MCList[nIndex][4],
				    pAdapter->MCList[nIndex][5]);

			result = ether_crc(6, pAdapter->MCList[nIndex]);

			result = (result & 0x3F800000) >> 23;

			if (result < 32) {
				hash1 |= (1 << result);
			} else if ((31 < result) && (result < 64)) {
				result -= 32;
				hash2 |= (1 << result);
			} else if ((63 < result) && (result < 96)) {
				result -= 64;
				hash3 |= (1 << result);
			} else {
				result -= 96;
				hash4 |= (1 << result);
			}
		}
	}

	/* Write out the new hash to the device */
	pm_csr.value = readl(&pAdapter->CSRAddress->global.pm_csr.value);
	if (pm_csr.bits.pm_phy_sw_coma == 0) {
		writel(hash1, &rxmac->multi_hash1);
		writel(hash2, &rxmac->multi_hash2);
		writel(hash3, &rxmac->multi_hash3);
		writel(hash4, &rxmac->multi_hash4);
	}

	DBG_LEAVE(et131x_dbginfo);
}

void SetupDeviceForUnicast(struct et131x_adapter *pAdapter)
{
	struct _RXMAC_t __iomem *rxmac = &pAdapter->CSRAddress->rxmac;
	RXMAC_UNI_PF_ADDR1_t uni_pf1;
	RXMAC_UNI_PF_ADDR2_t uni_pf2;
	RXMAC_UNI_PF_ADDR3_t uni_pf3;
	PM_CSR_t pm_csr;

	DBG_ENTER(et131x_dbginfo);

	/* Set up unicast packet filter reg 3 to be the first two octets of
	 * the MAC address for both address
	 *
	 * Set up unicast packet filter reg 2 to be the octets 2 - 5 of the
	 * MAC address for second address
	 *
	 * Set up unicast packet filter reg 3 to be the octets 2 - 5 of the
	 * MAC address for first address
	 */
	uni_pf3.bits.addr1_1 = pAdapter->CurrentAddress[0];
	uni_pf3.bits.addr1_2 = pAdapter->CurrentAddress[1];
	uni_pf3.bits.addr2_1 = pAdapter->CurrentAddress[0];
	uni_pf3.bits.addr2_2 = pAdapter->CurrentAddress[1];

	uni_pf2.bits.addr2_3 = pAdapter->CurrentAddress[2];
	uni_pf2.bits.addr2_4 = pAdapter->CurrentAddress[3];
	uni_pf2.bits.addr2_5 = pAdapter->CurrentAddress[4];
	uni_pf2.bits.addr2_6 = pAdapter->CurrentAddress[5];

	uni_pf1.bits.addr1_3 = pAdapter->CurrentAddress[2];
	uni_pf1.bits.addr1_4 = pAdapter->CurrentAddress[3];
	uni_pf1.bits.addr1_5 = pAdapter->CurrentAddress[4];
	uni_pf1.bits.addr1_6 = pAdapter->CurrentAddress[5];

	pm_csr.value = readl(&pAdapter->CSRAddress->global.pm_csr.value);
	if (pm_csr.bits.pm_phy_sw_coma == 0) {
		writel(uni_pf1.value, &rxmac->uni_pf_addr1.value);
		writel(uni_pf2.value, &rxmac->uni_pf_addr2.value);
		writel(uni_pf3.value, &rxmac->uni_pf_addr3.value);
	}

	DBG_LEAVE(et131x_dbginfo);
}