blob: fa95e9a009729f41ddd1c39174e4f6908f515226 [file] [log] [blame]
/* linux/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
* Copyright (C) 2009 Samsung Electronics Ltd.
* Jaswinder Singh <>
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
#ifndef __S3C64XX_PLAT_SPI_H
#define __S3C64XX_PLAT_SPI_H
struct platform_device;
* struct s3c64xx_spi_csinfo - ChipSelect description
* @fb_delay: Slave specific feedback delay.
* Refer to FB_CLK_SEL register definition in SPI chapter.
* @line: Custom 'identity' of the CS line.
* @set_level: CS line control.
* This is per SPI-Slave Chipselect information.
* Allocate and initialize one in machine init code and make the
* spi_board_info.controller_data point to it.
struct s3c64xx_spi_csinfo {
u8 fb_delay;
unsigned line;
void (*set_level)(unsigned line_id, int lvl);
* struct s3c64xx_spi_info - SPI Controller defining structure
* @src_clk_nr: Clock source index for the CLK_CFG[SPI_CLKSEL] field.
* @clk_from_cmu: If the SPI clock/prescalar control block is present
* by the platform's clock-management-unit and not in SPI controller.
* @num_cs: Number of CS this controller emulates.
* @cfg_gpio: Configure pins for this SPI controller.
* @fifo_lvl_mask: All tx fifo_lvl fields start at offset-6
* @rx_lvl_offset: Depends on tx fifo_lvl field and bus number
* @high_speed: If the controller supports HIGH_SPEED_EN bit
* @tx_st_done: Depends on tx fifo_lvl field
struct s3c64xx_spi_info {
int src_clk_nr;
bool clk_from_cmu;
int num_cs;
int (*cfg_gpio)(struct platform_device *pdev);
/* Following two fields are for future compatibility */
int fifo_lvl_mask;
int rx_lvl_offset;
int high_speed;
int tx_st_done;
* s3c64xx_spi_set_platdata - SPI Controller configure callback by the board
* initialization code.
* @pd: SPI platform data to set.
* @src_clk_nr: Clock the SPI controller is to use to generate SPI clocks.
* @num_cs: Number of elements in the 'cs' array.
* Call this from machine init code for each SPI Controller that
* has some chips attached to it.
extern void s3c64xx_spi0_set_platdata(struct s3c64xx_spi_info *pd,
int src_clk_nr, int num_cs);
extern void s3c64xx_spi1_set_platdata(struct s3c64xx_spi_info *pd,
int src_clk_nr, int num_cs);
extern void s3c64xx_spi2_set_platdata(struct s3c64xx_spi_info *pd,
int src_clk_nr, int num_cs);
/* defined by architecture to configure gpio */
extern int s3c64xx_spi0_cfg_gpio(struct platform_device *dev);
extern int s3c64xx_spi1_cfg_gpio(struct platform_device *dev);
extern int s3c64xx_spi2_cfg_gpio(struct platform_device *dev);
extern struct s3c64xx_spi_info s3c64xx_spi0_pdata;
extern struct s3c64xx_spi_info s3c64xx_spi1_pdata;
extern struct s3c64xx_spi_info s3c64xx_spi2_pdata;
#endif /* __S3C64XX_PLAT_SPI_H */