| /* |
| * Setup code for AT91SAM Evaluation Kits with Device Tree support |
| * |
| * Covers: * AT91SAM9G45-EKES board |
| * * AT91SAM9M10-EKES board |
| * * AT91SAM9M10G45-EK board |
| * |
| * Copyright (C) 2011 Atmel, |
| * 2011 Nicolas Ferre <nicolas.ferre@atmel.com> |
| * |
| * Licensed under GPLv2 or later. |
| */ |
| |
| #include <linux/types.h> |
| #include <linux/init.h> |
| #include <linux/module.h> |
| #include <linux/gpio.h> |
| #include <linux/irqdomain.h> |
| #include <linux/of_irq.h> |
| #include <linux/of_platform.h> |
| |
| #include <mach/hardware.h> |
| #include <mach/board.h> |
| #include <mach/system_rev.h> |
| #include <mach/at91sam9_smc.h> |
| |
| #include <asm/setup.h> |
| #include <asm/irq.h> |
| #include <asm/mach/arch.h> |
| #include <asm/mach/map.h> |
| #include <asm/mach/irq.h> |
| |
| #include "sam9_smc.h" |
| #include "generic.h" |
| |
| |
| static void __init ek_init_early(void) |
| { |
| /* Initialize processor: 12.000 MHz crystal */ |
| at91_initialize(12000000); |
| |
| /* DGBU on ttyS0. (Rx & Tx only) */ |
| at91_register_uart(0, 0, 0); |
| |
| /* set serial console to ttyS0 (ie, DBGU) */ |
| at91_set_serial_console(0); |
| } |
| |
| /* det_pin is not connected */ |
| static struct atmel_nand_data __initdata ek_nand_data = { |
| .ale = 21, |
| .cle = 22, |
| .det_pin = -EINVAL, |
| .rdy_pin = AT91_PIN_PC8, |
| .enable_pin = AT91_PIN_PC14, |
| }; |
| |
| static struct sam9_smc_config __initdata ek_nand_smc_config = { |
| .ncs_read_setup = 0, |
| .nrd_setup = 2, |
| .ncs_write_setup = 0, |
| .nwe_setup = 2, |
| |
| .ncs_read_pulse = 4, |
| .nrd_pulse = 4, |
| .ncs_write_pulse = 4, |
| .nwe_pulse = 4, |
| |
| .read_cycle = 7, |
| .write_cycle = 7, |
| |
| .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE, |
| .tdf_cycles = 3, |
| }; |
| |
| static void __init ek_add_device_nand(void) |
| { |
| ek_nand_data.bus_width_16 = board_have_nand_16bit(); |
| /* setup bus-width (8 or 16) */ |
| if (ek_nand_data.bus_width_16) |
| ek_nand_smc_config.mode |= AT91_SMC_DBW_16; |
| else |
| ek_nand_smc_config.mode |= AT91_SMC_DBW_8; |
| |
| /* configure chip-select 3 (NAND) */ |
| sam9_smc_configure(0, 3, &ek_nand_smc_config); |
| |
| at91_add_device_nand(&ek_nand_data); |
| } |
| |
| static const struct of_device_id aic_of_match[] __initconst = { |
| { .compatible = "atmel,at91rm9200-aic", }, |
| {}, |
| }; |
| |
| static void __init at91_dt_init_irq(void) |
| { |
| irq_domain_generate_simple(aic_of_match, 0xfffff000, 0); |
| at91_init_irq_default(); |
| } |
| |
| static void __init at91_dt_device_init(void) |
| { |
| of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); |
| |
| /* NAND */ |
| ek_add_device_nand(); |
| } |
| |
| static const char *at91_dt_board_compat[] __initdata = { |
| "atmel,at91sam9m10g45ek", |
| "calao,usb-a9g20", |
| NULL |
| }; |
| |
| DT_MACHINE_START(at91sam_dt, "Atmel AT91SAM (Device Tree)") |
| /* Maintainer: Atmel */ |
| .timer = &at91sam926x_timer, |
| .map_io = at91_map_io, |
| .init_early = ek_init_early, |
| .init_irq = at91_dt_init_irq, |
| .init_machine = at91_dt_device_init, |
| .dt_compat = at91_dt_board_compat, |
| MACHINE_END |
