blob: e854d5741c8889daad675ae230bef5848bdcf6fa [file] [log] [blame]
/*
* linux/arch/arm/mach-omap1/board-perseus2.c
*
* Modified from board-generic.c
*
* Original OMAP730 support by Jean Pihet <j-pihet@ti.com>
* Updated for 2.6 by Kevin Hilman <kjh@hilman.org>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <linux/input.h>
#include <linux/smc91x.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <plat/tc.h>
#include <mach/gpio.h>
#include <plat/mux.h>
#include <plat/fpga.h>
#include <plat/flash.h>
#include <plat/keypad.h>
#include <plat/common.h>
#include <plat/board.h>
static int p2_keymap[] = {
KEY(0,0,KEY_UP),
KEY(0,1,KEY_RIGHT),
KEY(0,2,KEY_LEFT),
KEY(0,3,KEY_DOWN),
KEY(0,4,KEY_ENTER),
KEY(1,0,KEY_F10),
KEY(1,1,KEY_SEND),
KEY(1,2,KEY_END),
KEY(1,3,KEY_VOLUMEDOWN),
KEY(1,4,KEY_VOLUMEUP),
KEY(1,5,KEY_RECORD),
KEY(2,0,KEY_F9),
KEY(2,1,KEY_3),
KEY(2,2,KEY_6),
KEY(2,3,KEY_9),
KEY(2,4,KEY_KPDOT),
KEY(3,0,KEY_BACK),
KEY(3,1,KEY_2),
KEY(3,2,KEY_5),
KEY(3,3,KEY_8),
KEY(3,4,KEY_0),
KEY(3,5,KEY_KPSLASH),
KEY(4,0,KEY_HOME),
KEY(4,1,KEY_1),
KEY(4,2,KEY_4),
KEY(4,3,KEY_7),
KEY(4,4,KEY_KPASTERISK),
KEY(4,5,KEY_POWER),
0
};
static struct smc91x_platdata smc91x_info = {
.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
.leda = RPC_LED_100_10,
.ledb = RPC_LED_TX_RX,
};
static struct resource smc91x_resources[] = {
[0] = {
.start = H2P2_DBG_FPGA_ETHR_START, /* Physical */
.end = H2P2_DBG_FPGA_ETHR_START + 0xf,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = INT_7XX_MPU_EXT_NIRQ,
.end = 0,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
},
};
static struct mtd_partition nor_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
.name = "bootloader",
.offset = 0,
.size = SZ_128K,
.mask_flags = MTD_WRITEABLE, /* force read-only */
},
/* bootloader params in the next sector */
{
.name = "params",
.offset = MTDPART_OFS_APPEND,
.size = SZ_128K,
.mask_flags = 0,
},
/* kernel */
{
.name = "kernel",
.offset = MTDPART_OFS_APPEND,
.size = SZ_2M,
.mask_flags = 0
},
/* rest of flash is a file system */
{
.name = "rootfs",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
.mask_flags = 0
},
};
static struct physmap_flash_data nor_data = {
.width = 2,
.set_vpp = omap1_set_vpp,
.parts = nor_partitions,
.nr_parts = ARRAY_SIZE(nor_partitions),
};
static struct resource nor_resource = {
.start = OMAP_CS0_PHYS,
.end = OMAP_CS0_PHYS + SZ_32M - 1,
.flags = IORESOURCE_MEM,
};
static struct platform_device nor_device = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &nor_data,
},
.num_resources = 1,
.resource = &nor_resource,
};
static void nand_cmd_ctl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
{
struct nand_chip *this = mtd->priv;
unsigned long mask;
if (cmd == NAND_CMD_NONE)
return;
mask = (ctrl & NAND_CLE) ? 0x02 : 0;
if (ctrl & NAND_ALE)
mask |= 0x04;
writeb(cmd, (unsigned long)this->IO_ADDR_W | mask);
}
#define P2_NAND_RB_GPIO_PIN 62
static int nand_dev_ready(struct mtd_info *mtd)
{
return gpio_get_value(P2_NAND_RB_GPIO_PIN);
}
static const char *part_probes[] = { "cmdlinepart", NULL };
static struct platform_nand_data nand_data = {
.chip = {
.nr_chips = 1,
.chip_offset = 0,
.options = NAND_SAMSUNG_LP_OPTIONS,
.part_probe_types = part_probes,
},
.ctrl = {
.cmd_ctrl = nand_cmd_ctl,
.dev_ready = nand_dev_ready,
},
};
static struct resource nand_resource = {
.start = OMAP_CS3_PHYS,
.end = OMAP_CS3_PHYS + SZ_4K - 1,
.flags = IORESOURCE_MEM,
};
static struct platform_device nand_device = {
.name = "gen_nand",
.id = 0,
.dev = {
.platform_data = &nand_data,
},
.num_resources = 1,
.resource = &nand_resource,
};
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = 0,
.dev = {
.platform_data = &smc91x_info,
},
.num_resources = ARRAY_SIZE(smc91x_resources),
.resource = smc91x_resources,
};
static struct resource kp_resources[] = {
[0] = {
.start = INT_7XX_MPUIO_KEYPAD,
.end = INT_7XX_MPUIO_KEYPAD,
.flags = IORESOURCE_IRQ,
},
};
static struct omap_kp_platform_data kp_data = {
.rows = 8,
.cols = 8,
.keymap = p2_keymap,
.keymapsize = ARRAY_SIZE(p2_keymap),
.delay = 4,
.dbounce = 1,
};
static struct platform_device kp_device = {
.name = "omap-keypad",
.id = -1,
.dev = {
.platform_data = &kp_data,
},
.num_resources = ARRAY_SIZE(kp_resources),
.resource = kp_resources,
};
static struct platform_device lcd_device = {
.name = "lcd_p2",
.id = -1,
};
static struct platform_device *devices[] __initdata = {
&nor_device,
&nand_device,
&smc91x_device,
&kp_device,
&lcd_device,
};
static struct omap_lcd_config perseus2_lcd_config __initdata = {
.ctrl_name = "internal",
};
static struct omap_board_config_kernel perseus2_config[] __initdata = {
{ OMAP_TAG_LCD, &perseus2_lcd_config },
};
static void __init omap_perseus2_init(void)
{
if (gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
BUG();
gpio_direction_input(P2_NAND_RB_GPIO_PIN);
omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
platform_add_devices(devices, ARRAY_SIZE(devices));
omap_board_config = perseus2_config;
omap_board_config_size = ARRAY_SIZE(perseus2_config);
omap_serial_init();
omap_register_i2c_bus(1, 100, NULL, 0);
}
static void __init perseus2_init_smc91x(void)
{
fpga_write(1, H2P2_DBG_FPGA_LAN_RESET);
mdelay(50);
fpga_write(fpga_read(H2P2_DBG_FPGA_LAN_RESET) & ~1,
H2P2_DBG_FPGA_LAN_RESET);
mdelay(50);
}
static void __init omap_perseus2_init_irq(void)
{
omap1_init_common_hw();
omap_init_irq();
omap_gpio_init();
perseus2_init_smc91x();
}
/* Only FPGA needs to be mapped here. All others are done with ioremap */
static struct map_desc omap_perseus2_io_desc[] __initdata = {
{
.virtual = H2P2_DBG_FPGA_BASE,
.pfn = __phys_to_pfn(H2P2_DBG_FPGA_START),
.length = H2P2_DBG_FPGA_SIZE,
.type = MT_DEVICE
}
};
static void __init omap_perseus2_map_io(void)
{
omap1_map_common_io();
iotable_init(omap_perseus2_io_desc,
ARRAY_SIZE(omap_perseus2_io_desc));
/* Early, board-dependent init */
/*
* Hold GSM Reset until needed
*/
omap_writew(omap_readw(OMAP7XX_DSP_M_CTL) & ~1, OMAP7XX_DSP_M_CTL);
/*
* UARTs -> done automagically by 8250 driver
*/
/*
* CSx timings, GPIO Mux ... setup
*/
/* Flash: CS0 timings setup */
omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_0);
omap_writel(0x00000088, OMAP7XX_FLASH_ACFG_0);
/*
* Ethernet support through the debug board
* CS1 timings setup
*/
omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_1);
omap_writel(0x00000000, OMAP7XX_FLASH_ACFG_1);
/*
* Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
* It is used as the Ethernet controller interrupt
*/
omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF, OMAP7XX_IO_CONF_9);
}
MACHINE_START(OMAP_PERSEUS2, "OMAP730 Perseus2")
/* Maintainer: Kevin Hilman <kjh@hilman.org> */
.phys_io = 0xfff00000,
.io_pg_offst = ((0xfef00000) >> 18) & 0xfffc,
.boot_params = 0x10000100,
.map_io = omap_perseus2_map_io,
.init_irq = omap_perseus2_init_irq,
.init_machine = omap_perseus2_init,
.timer = &omap_timer,
MACHINE_END