Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt - kernel/quantenna - Git at Google

 Samsung GPIO and Pin Mux/Config controller

 Samsung's ARM based SoC's integrates a GPIO and Pin mux/config hardware
 controller. It controls the input/output settings on the available pads/pins
 and also provides ability to multiplex and configure the output of various
 on-chip controllers onto these pads.

 Required Properties:
 - compatible: should be one of the following.
   - "samsung,s3c2412-pinctrl": for S3C2412-compatible pin-controller,
   - "samsung,s3c2416-pinctrl": for S3C2416-compatible pin-controller,
   - "samsung,s3c2440-pinctrl": for S3C2440-compatible pin-controller,
   - "samsung,s3c2450-pinctrl": for S3C2450-compatible pin-controller,
   - "samsung,s3c64xx-pinctrl": for S3C64xx-compatible pin-controller,
   - "samsung,s5pv210-pinctrl": for S5PV210-compatible pin-controller,
   - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller.
   - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller.
   - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller.
   - "samsung,exynos5260-pinctrl": for Exynos5260 compatible pin-controller.
   - "samsung,exynos5410-pinctrl": for Exynos5410 compatible pin-controller.
   - "samsung,exynos5420-pinctrl": for Exynos5420 compatible pin-controller.
   - "samsung,exynos7-pinctrl": for Exynos7 compatible pin-controller.

 - reg: Base address of the pin controller hardware module and length of
   the address space it occupies.

 - Pin banks as child nodes: Pin banks of the controller are represented by child
   nodes of the controller node. Bank name is taken from name of the node. Each
   bank node must contain following properties:

   - gpio-controller: identifies the node as a gpio controller and pin bank.
   - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
     binding is used, the amount of cells must be specified as 2. See the below
     mentioned gpio binding representation for description of particular cells.

 	Eg: <&gpx2 6 0>
 	<[phandle of the gpio controller node]
 	[pin number within the gpio controller]
 	[flags]>

 	Values for gpio specifier:
 	- Pin number: is a value between 0 to 7.
 	- Flags: 0 - Active High
 		 1 - Active Low

 - Pin mux/config groups as child nodes: The pin mux (selecting pin function
   mode) and pin config (pull up/down, driver strength) settings are represented
   as child nodes of the pin-controller node. There should be atleast one
   child node and there is no limit on the count of these child nodes. It is
   also possible for a child node to consist of several further child nodes
   to allow grouping multiple pinctrl groups into one. The format of second
   level child nodes is exactly the same as for first level ones and is
   described below.

   The child node should contain a list of pin(s) on which a particular pin
   function selection or pin configuration (or both) have to applied. This
   list of pins is specified using the property name "samsung,pins". There
   should be atleast one pin specfied for this property and there is no upper
   limit on the count of pins that can be specified. The pins are specified
   using pin names which are derived from the hardware manual of the SoC. As
   an example, the pins in GPA0 bank of the pin controller can be represented
   as "gpa0-0", "gpa0-1", "gpa0-2" and so on. The names should be in lower case.
   The format of the pin names should be (as per the hardware manual)
   "[pin bank name]-[pin number within the bank]".

   The pin function selection that should be applied on the pins listed in the
   child node is specified using the "samsung,pin-function" property. The value
   of this property that should be applied to each of the pins listed in the
   "samsung,pins" property should be picked from the hardware manual of the SoC
   for the specified pin group. This property is optional in the child node if
   no specific function selection is desired for the pins listed in the child
   node. The value of this property is used as-is to program the pin-controller
   function selector register of the pin-bank.

   The child node can also optionally specify one or more of the pin
   configuration that should be applied on all the pins listed in the
   "samsung,pins" property of the child node. The following pin configuration
   properties are supported.

   - samsung,pin-val: Initial value of pin output buffer.
   - samsung,pin-pud: Pull up/down configuration.
   - samsung,pin-drv: Drive strength configuration.
   - samsung,pin-pud-pdn: Pull up/down configuration in power down mode.
   - samsung,pin-drv-pdn: Drive strength configuration in power down mode.

   The values specified by these config properties should be derived from the
   hardware manual and these values are programmed as-is into the pin
   pull up/down and driver strength register of the pin-controller.

   Note: A child should include atleast a pin function selection property or
   pin configuration property (one or more) or both.

   The client nodes that require a particular pin function selection and/or
   pin configuration should use the bindings listed in the "pinctrl-bindings.txt"
   file.

 External GPIO and Wakeup Interrupts:

 The controller supports two types of external interrupts over gpio. The first
 is the external gpio interrupt and second is the external wakeup interrupts.
 The difference between the two is that the external wakeup interrupts can be
 used as system wakeup events.

 A. External GPIO Interrupts: For supporting external gpio interrupts, the
    following properties should be specified in the pin-controller device node.

    - interrupt-parent: phandle of the interrupt parent to which the external
      GPIO interrupts are forwarded to.
    - interrupts: interrupt specifier for the controller. The format and value of
      the interrupt specifier depends on the interrupt parent for the controller.

    In addition, following properties must be present in node of every bank
    of pins supporting GPIO interrupts:

    - interrupt-controller: identifies the controller node as interrupt-parent.
    - #interrupt-cells: the value of this property should be 2.
      - First Cell: represents the external gpio interrupt number local to the
        external gpio interrupt space of the controller.
      - Second Cell: flags to identify the type of the interrupt
        - 1 = rising edge triggered
        - 2 = falling edge triggered
        - 3 = rising and falling edge triggered
        - 4 = high level triggered
        - 8 = low level triggered

 B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
    child node representing the external wakeup interrupt controller should be
    included in the pin-controller device node. This child node should include
    the following properties.

    - compatible: identifies the type of the external wakeup interrupt controller
      The possible values are:
      - samsung,s3c2410-wakeup-eint: represents wakeup interrupt controller
        found on Samsung S3C24xx SoCs except S3C2412 and S3C2413,
      - samsung,s3c2412-wakeup-eint: represents wakeup interrupt controller
        found on Samsung S3C2412 and S3C2413 SoCs,
      - samsung,s3c64xx-wakeup-eint: represents wakeup interrupt controller
        found on Samsung S3C64xx SoCs,
      - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller
        found on Samsung Exynos4210 and S5PC110/S5PV210 SoCs.
      - samsung,exynos7-wakeup-eint: represents wakeup interrupt controller
        found on Samsung Exynos7 SoC.
    - interrupt-parent: phandle of the interrupt parent to which the external
      wakeup interrupts are forwarded to.
    - interrupts: interrupt used by multiplexed wakeup interrupts.

    In addition, following properties must be present in node of every bank
    of pins supporting wake-up interrupts:

    - interrupt-controller: identifies the node as interrupt-parent.
    - #interrupt-cells: the value of this property should be 2
      - First Cell: represents the external wakeup interrupt number local to
        the external wakeup interrupt space of the controller.
      - Second Cell: flags to identify the type of the interrupt
        - 1 = rising edge triggered
        - 2 = falling edge triggered
        - 3 = rising and falling edge triggered
        - 4 = high level triggered
        - 8 = low level triggered

    Node of every bank of pins supporting direct wake-up interrupts (without
    multiplexing) must contain following properties:

    - interrupt-parent: phandle of the interrupt parent to which the external
      wakeup interrupts are forwarded to.
    - interrupts: interrupts of the interrupt parent which are used for external
      wakeup interrupts from pins of the bank, must contain interrupts for all
      pins of the bank.

 Aliases:

 All the pin controller nodes should be represented in the aliases node using
 the following format 'pinctrl{n}' where n is a unique number for the alias.

 Aliases for controllers compatible with "samsung,exynos7-pinctrl":
 - pinctrl0: pin controller of ALIVE block,
 - pinctrl1: pin controller of BUS0 block,
 - pinctrl2: pin controller of NFC block,
 - pinctrl3: pin controller of TOUCH block,
 - pinctrl4: pin controller of FF block,
 - pinctrl5: pin controller of ESE block,
 - pinctrl6: pin controller of FSYS0 block,
 - pinctrl7: pin controller of FSYS1 block,
 - pinctrl8: pin controller of BUS1 block,
 - pinctrl9: pin controller of AUDIO block,

 Example: A pin-controller node with pin banks:

 	pinctrl_0: pinctrl@11400000 {
 		compatible = "samsung,exynos4210-pinctrl";
 		reg = <0x11400000 0x1000>;
 		interrupts = <0 47 0>;

 		/* ... */

 		/* Pin bank without external interrupts */
 		gpy0: gpy0 {
 			gpio-controller;
 			#gpio-cells = <2>;
 		};

 		/* ... */

 		/* Pin bank with external GPIO or muxed wake-up interrupts */
 		gpj0: gpj0 {
 			gpio-controller;
 			#gpio-cells = <2>;

 			interrupt-controller;
 			#interrupt-cells = <2>;
 		};

 		/* ... */

 		/* Pin bank with external direct wake-up interrupts */
 		gpx0: gpx0 {
 			gpio-controller;
 			#gpio-cells = <2>;

 			interrupt-controller;
 			interrupt-parent = <&gic>;
 			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
 				     <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>;
 			#interrupt-cells = <2>;
 		};

 		/* ... */
 	};

 Example 1: A pin-controller node with pin groups.

 	pinctrl_0: pinctrl@11400000 {
 		compatible = "samsung,exynos4210-pinctrl";
 		reg = <0x11400000 0x1000>;
 		interrupts = <0 47 0>;

 		/* ... */

 		uart0_data: uart0-data {
 			samsung,pins = "gpa0-0", "gpa0-1";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <0>;
 			samsung,pin-drv = <0>;
 		};

 		uart0_fctl: uart0-fctl {
 			samsung,pins = "gpa0-2", "gpa0-3";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <0>;
 			samsung,pin-drv = <0>;
 		};

 		uart1_data: uart1-data {
 			samsung,pins = "gpa0-4", "gpa0-5";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <0>;
 			samsung,pin-drv = <0>;
 		};

 		uart1_fctl: uart1-fctl {
 			samsung,pins = "gpa0-6", "gpa0-7";
 			samsung,pin-function = <2>;
 			samsung,pin-pud = <0>;
 			samsung,pin-drv = <0>;
 		};

 		i2c2_bus: i2c2-bus {
 			samsung,pins = "gpa0-6", "gpa0-7";
 			samsung,pin-function = <3>;
 			samsung,pin-pud = <3>;
 			samsung,pin-drv = <0>;
 		};

 		sd4_bus8: sd4-bus-width8 {
 			part-1 {
 				samsung,pins = "gpk0-3", "gpk0-4",
 						"gpk0-5", "gpk0-6";
 				samsung,pin-function = <3>;
 				samsung,pin-pud = <3>;
 				samsung,pin-drv = <3>;
 			};
 			part-2 {
 				samsung,pins = "gpk1-3", "gpk1-4",
 						"gpk1-5", "gpk1-6";
 				samsung,pin-function = <4>;
 				samsung,pin-pud = <4>;
 				samsung,pin-drv = <3>;
 			};
 		};
 	};

 Example 2: A pin-controller node with external wakeup interrupt controller node.

 	pinctrl_1: pinctrl@11000000 {
 		compatible = "samsung,exynos4210-pinctrl";
 		reg = <0x11000000 0x1000>;
 		interrupts = <0 46 0>

 		/* ... */

 		wakeup-interrupt-controller {
 			compatible = "samsung,exynos4210-wakeup-eint";
 			interrupt-parent = <&gic>;
 			interrupts = <0 32 0>;
 		};
 	};

 Example 3: A uart client node that supports 'default' and 'flow-control' states.

 	uart@13800000 {
 		compatible = "samsung,exynos4210-uart";
 		reg = <0x13800000 0x100>;
 		interrupts = <0 52 0>;
 		pinctrl-names = "default", "flow-control;
 		pinctrl-0 = <&uart0_data>;
 		pinctrl-1 = <&uart0_data &uart0_fctl>;
 	};

 Example 4: Set up the default pin state for uart controller.

 	static int s3c24xx_serial_probe(struct platform_device *pdev) {
 		struct pinctrl *pinctrl;

 		/* ... */

 		pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
 	}

 Example 5: A display port client node that supports 'default' pinctrl state
 	   and gpio binding.

 	display-port-controller {
 		/* ... */

 		samsung,hpd-gpio = <&gpx2 6 0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&dp_hpd>;
 	};

 Example 6: Request the gpio for display port controller

 	static int exynos_dp_probe(struct platform_device *pdev)
 	{
 		int hpd_gpio, ret;
 		struct device *dev = &pdev->dev;
 		struct device_node *dp_node = dev->of_node;

 		/* ... */

 		hpd_gpio = of_get_named_gpio(dp_node, "samsung,hpd-gpio", 0);

 		/* ... */

 		ret = devm_gpio_request_one(&pdev->dev, hpd_gpio, GPIOF_IN,
 					    "hpd_gpio");
 		/* ... */
 	}
	Samsung GPIO and Pin Mux/Config controller

	Samsung's ARM based SoC's integrates a GPIO and Pin mux/config hardware
	controller. It controls the input/output settings on the available pads/pins
	and also provides ability to multiplex and configure the output of various
	on-chip controllers onto these pads.

	Required Properties:
	- compatible: should be one of the following.
	- "samsung,s3c2412-pinctrl": for S3C2412-compatible pin-controller,
	- "samsung,s3c2416-pinctrl": for S3C2416-compatible pin-controller,
	- "samsung,s3c2440-pinctrl": for S3C2440-compatible pin-controller,
	- "samsung,s3c2450-pinctrl": for S3C2450-compatible pin-controller,
	- "samsung,s3c64xx-pinctrl": for S3C64xx-compatible pin-controller,
	- "samsung,s5pv210-pinctrl": for S5PV210-compatible pin-controller,
	- "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller.
	- "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller.
	- "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller.
	- "samsung,exynos5260-pinctrl": for Exynos5260 compatible pin-controller.
	- "samsung,exynos5410-pinctrl": for Exynos5410 compatible pin-controller.
	- "samsung,exynos5420-pinctrl": for Exynos5420 compatible pin-controller.
	- "samsung,exynos7-pinctrl": for Exynos7 compatible pin-controller.

	- reg: Base address of the pin controller hardware module and length of
	the address space it occupies.

	- Pin banks as child nodes: Pin banks of the controller are represented by child
	nodes of the controller node. Bank name is taken from name of the node. Each
	bank node must contain following properties:

	- gpio-controller: identifies the node as a gpio controller and pin bank.
	- #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
	binding is used, the amount of cells must be specified as 2. See the below
	mentioned gpio binding representation for description of particular cells.

	Eg: <&gpx2 6 0>
	<[phandle of the gpio controller node]
	[pin number within the gpio controller]
	[flags]>

	Values for gpio specifier:
	- Pin number: is a value between 0 to 7.
	- Flags: 0 - Active High
	1 - Active Low

	- Pin mux/config groups as child nodes: The pin mux (selecting pin function
	mode) and pin config (pull up/down, driver strength) settings are represented
	as child nodes of the pin-controller node. There should be atleast one
	child node and there is no limit on the count of these child nodes. It is
	also possible for a child node to consist of several further child nodes
	to allow grouping multiple pinctrl groups into one. The format of second
	level child nodes is exactly the same as for first level ones and is
	described below.

	The child node should contain a list of pin(s) on which a particular pin
	function selection or pin configuration (or both) have to applied. This
	list of pins is specified using the property name "samsung,pins". There
	should be atleast one pin specfied for this property and there is no upper
	limit on the count of pins that can be specified. The pins are specified
	using pin names which are derived from the hardware manual of the SoC. As
	an example, the pins in GPA0 bank of the pin controller can be represented
	as "gpa0-0", "gpa0-1", "gpa0-2" and so on. The names should be in lower case.
	The format of the pin names should be (as per the hardware manual)
	"[pin bank name]-[pin number within the bank]".

	The pin function selection that should be applied on the pins listed in the
	child node is specified using the "samsung,pin-function" property. The value
	of this property that should be applied to each of the pins listed in the
	"samsung,pins" property should be picked from the hardware manual of the SoC
	for the specified pin group. This property is optional in the child node if
	no specific function selection is desired for the pins listed in the child
	node. The value of this property is used as-is to program the pin-controller
	function selector register of the pin-bank.

	The child node can also optionally specify one or more of the pin
	configuration that should be applied on all the pins listed in the
	"samsung,pins" property of the child node. The following pin configuration
	properties are supported.

	- samsung,pin-val: Initial value of pin output buffer.
	- samsung,pin-pud: Pull up/down configuration.
	- samsung,pin-drv: Drive strength configuration.
	- samsung,pin-pud-pdn: Pull up/down configuration in power down mode.
	- samsung,pin-drv-pdn: Drive strength configuration in power down mode.

	The values specified by these config properties should be derived from the
	hardware manual and these values are programmed as-is into the pin
	pull up/down and driver strength register of the pin-controller.

	Note: A child should include atleast a pin function selection property or
	pin configuration property (one or more) or both.

	The client nodes that require a particular pin function selection and/or
	pin configuration should use the bindings listed in the "pinctrl-bindings.txt"
	file.

	External GPIO and Wakeup Interrupts:

	The controller supports two types of external interrupts over gpio. The first
	is the external gpio interrupt and second is the external wakeup interrupts.
	The difference between the two is that the external wakeup interrupts can be
	used as system wakeup events.

	A. External GPIO Interrupts: For supporting external gpio interrupts, the
	following properties should be specified in the pin-controller device node.

	- interrupt-parent: phandle of the interrupt parent to which the external
	GPIO interrupts are forwarded to.
	- interrupts: interrupt specifier for the controller. The format and value of
	the interrupt specifier depends on the interrupt parent for the controller.

	In addition, following properties must be present in node of every bank
	of pins supporting GPIO interrupts:

	- interrupt-controller: identifies the controller node as interrupt-parent.
	- #interrupt-cells: the value of this property should be 2.
	- First Cell: represents the external gpio interrupt number local to the
	external gpio interrupt space of the controller.
	- Second Cell: flags to identify the type of the interrupt
	- 1 = rising edge triggered
	- 2 = falling edge triggered
	- 3 = rising and falling edge triggered
	- 4 = high level triggered
	- 8 = low level triggered

	B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
	child node representing the external wakeup interrupt controller should be
	included in the pin-controller device node. This child node should include
	the following properties.

	- compatible: identifies the type of the external wakeup interrupt controller
	The possible values are:
	- samsung,s3c2410-wakeup-eint: represents wakeup interrupt controller
	found on Samsung S3C24xx SoCs except S3C2412 and S3C2413,
	- samsung,s3c2412-wakeup-eint: represents wakeup interrupt controller
	found on Samsung S3C2412 and S3C2413 SoCs,
	- samsung,s3c64xx-wakeup-eint: represents wakeup interrupt controller
	found on Samsung S3C64xx SoCs,
	- samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller
	found on Samsung Exynos4210 and S5PC110/S5PV210 SoCs.
	- samsung,exynos7-wakeup-eint: represents wakeup interrupt controller
	found on Samsung Exynos7 SoC.
	- interrupt-parent: phandle of the interrupt parent to which the external
	wakeup interrupts are forwarded to.
	- interrupts: interrupt used by multiplexed wakeup interrupts.

	In addition, following properties must be present in node of every bank
	of pins supporting wake-up interrupts:

	- interrupt-controller: identifies the node as interrupt-parent.
	- #interrupt-cells: the value of this property should be 2
	- First Cell: represents the external wakeup interrupt number local to
	the external wakeup interrupt space of the controller.
	- Second Cell: flags to identify the type of the interrupt
	- 1 = rising edge triggered
	- 2 = falling edge triggered
	- 3 = rising and falling edge triggered
	- 4 = high level triggered
	- 8 = low level triggered

	Node of every bank of pins supporting direct wake-up interrupts (without
	multiplexing) must contain following properties:

	- interrupt-parent: phandle of the interrupt parent to which the external
	wakeup interrupts are forwarded to.
	- interrupts: interrupts of the interrupt parent which are used for external
	wakeup interrupts from pins of the bank, must contain interrupts for all
	pins of the bank.

	Aliases:

	All the pin controller nodes should be represented in the aliases node using
	the following format 'pinctrl{n}' where n is a unique number for the alias.

	Aliases for controllers compatible with "samsung,exynos7-pinctrl":
	- pinctrl0: pin controller of ALIVE block,
	- pinctrl1: pin controller of BUS0 block,
	- pinctrl2: pin controller of NFC block,
	- pinctrl3: pin controller of TOUCH block,
	- pinctrl4: pin controller of FF block,
	- pinctrl5: pin controller of ESE block,
	- pinctrl6: pin controller of FSYS0 block,
	- pinctrl7: pin controller of FSYS1 block,
	- pinctrl8: pin controller of BUS1 block,
	- pinctrl9: pin controller of AUDIO block,

	Example: A pin-controller node with pin banks:

	pinctrl_0: pinctrl@11400000 {
	compatible = "samsung,exynos4210-pinctrl";
	reg = <0x11400000 0x1000>;
	interrupts = <0 47 0>;

	/* ... */

	/* Pin bank without external interrupts */
	gpy0: gpy0 {
	gpio-controller;
	#gpio-cells = <2>;
	};

	/* ... */

	/* Pin bank with external GPIO or muxed wake-up interrupts */
	gpj0: gpj0 {
	gpio-controller;
	#gpio-cells = <2>;

	interrupt-controller;
	#interrupt-cells = <2>;
	};

	/* ... */

	/* Pin bank with external direct wake-up interrupts */
	gpx0: gpx0 {
	gpio-controller;
	#gpio-cells = <2>;

	interrupt-controller;
	interrupt-parent = <&gic>;
	interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
	<0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>;
	#interrupt-cells = <2>;
	};

	/* ... */
	};

	Example 1: A pin-controller node with pin groups.

	pinctrl_0: pinctrl@11400000 {
	compatible = "samsung,exynos4210-pinctrl";
	reg = <0x11400000 0x1000>;
	interrupts = <0 47 0>;

	/* ... */

	uart0_data: uart0-data {
	samsung,pins = "gpa0-0", "gpa0-1";
	samsung,pin-function = <2>;
	samsung,pin-pud = <0>;
	samsung,pin-drv = <0>;
	};

	uart0_fctl: uart0-fctl {
	samsung,pins = "gpa0-2", "gpa0-3";
	samsung,pin-function = <2>;
	samsung,pin-pud = <0>;
	samsung,pin-drv = <0>;
	};

	uart1_data: uart1-data {
	samsung,pins = "gpa0-4", "gpa0-5";
	samsung,pin-function = <2>;
	samsung,pin-pud = <0>;
	samsung,pin-drv = <0>;
	};

	uart1_fctl: uart1-fctl {
	samsung,pins = "gpa0-6", "gpa0-7";
	samsung,pin-function = <2>;
	samsung,pin-pud = <0>;
	samsung,pin-drv = <0>;
	};

	i2c2_bus: i2c2-bus {
	samsung,pins = "gpa0-6", "gpa0-7";
	samsung,pin-function = <3>;
	samsung,pin-pud = <3>;
	samsung,pin-drv = <0>;
	};

	sd4_bus8: sd4-bus-width8 {
	part-1 {
	samsung,pins = "gpk0-3", "gpk0-4",
	"gpk0-5", "gpk0-6";
	samsung,pin-function = <3>;
	samsung,pin-pud = <3>;
	samsung,pin-drv = <3>;
	};
	part-2 {
	samsung,pins = "gpk1-3", "gpk1-4",
	"gpk1-5", "gpk1-6";
	samsung,pin-function = <4>;
	samsung,pin-pud = <4>;
	samsung,pin-drv = <3>;
	};
	};
	};

	Example 2: A pin-controller node with external wakeup interrupt controller node.

	pinctrl_1: pinctrl@11000000 {
	compatible = "samsung,exynos4210-pinctrl";
	reg = <0x11000000 0x1000>;
	interrupts = <0 46 0>

	/* ... */

	wakeup-interrupt-controller {
	compatible = "samsung,exynos4210-wakeup-eint";
	interrupt-parent = <&gic>;
	interrupts = <0 32 0>;
	};
	};

	Example 3: A uart client node that supports 'default' and 'flow-control' states.

	uart@13800000 {
	compatible = "samsung,exynos4210-uart";
	reg = <0x13800000 0x100>;
	interrupts = <0 52 0>;
	pinctrl-names = "default", "flow-control;
	pinctrl-0 = <&uart0_data>;
	pinctrl-1 = <&uart0_data &uart0_fctl>;
	};

	Example 4: Set up the default pin state for uart controller.

	static int s3c24xx_serial_probe(struct platform_device *pdev) {
	struct pinctrl *pinctrl;

	/* ... */

	pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
	}

	Example 5: A display port client node that supports 'default' pinctrl state
	and gpio binding.

	display-port-controller {
	/* ... */

	samsung,hpd-gpio = <&gpx2 6 0>;
	pinctrl-names = "default";
	pinctrl-0 = <&dp_hpd>;
	};

	Example 6: Request the gpio for display port controller

	static int exynos_dp_probe(struct platform_device *pdev)
	{
	int hpd_gpio, ret;
	struct device *dev = &pdev->dev;
	struct device_node *dp_node = dev->of_node;

	/* ... */

	hpd_gpio = of_get_named_gpio(dp_node, "samsung,hpd-gpio", 0);

	/* ... */

	ret = devm_gpio_request_one(&pdev->dev, hpd_gpio, GPIOF_IN,
	"hpd_gpio");
	/* ... */
	}