| /* |
| * Copyright 2014 Freescale Semiconductor, Inc. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include <dt-bindings/clock/imx6sx-clock.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include "imx6sx-pinfunc.h" |
| #include "skeleton.dtsi" |
| |
| / { |
| aliases { |
| can0 = &flexcan1; |
| can1 = &flexcan2; |
| ethernet0 = &fec1; |
| ethernet1 = &fec2; |
| gpio0 = &gpio1; |
| gpio1 = &gpio2; |
| gpio2 = &gpio3; |
| gpio3 = &gpio4; |
| gpio4 = &gpio5; |
| gpio5 = &gpio6; |
| gpio6 = &gpio7; |
| i2c0 = &i2c1; |
| i2c1 = &i2c2; |
| i2c2 = &i2c3; |
| i2c3 = &i2c4; |
| mmc0 = &usdhc1; |
| mmc1 = &usdhc2; |
| mmc2 = &usdhc3; |
| mmc3 = &usdhc4; |
| serial0 = &uart1; |
| serial1 = &uart2; |
| serial2 = &uart3; |
| serial3 = &uart4; |
| serial4 = &uart5; |
| serial5 = &uart6; |
| spi0 = &ecspi1; |
| spi1 = &ecspi2; |
| spi2 = &ecspi3; |
| spi3 = &ecspi4; |
| spi4 = &ecspi5; |
| usbphy0 = &usbphy1; |
| usbphy1 = &usbphy2; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@0 { |
| compatible = "arm,cortex-a9"; |
| device_type = "cpu"; |
| reg = <0>; |
| next-level-cache = <&L2>; |
| operating-points = < |
| /* kHz uV */ |
| 996000 1250000 |
| 792000 1175000 |
| 396000 1075000 |
| 198000 975000 |
| >; |
| fsl,soc-operating-points = < |
| /* ARM kHz SOC uV */ |
| 996000 1175000 |
| 792000 1175000 |
| 396000 1175000 |
| 198000 1175000 |
| >; |
| clock-latency = <61036>; /* two CLK32 periods */ |
| clocks = <&clks IMX6SX_CLK_ARM>, |
| <&clks IMX6SX_CLK_PLL2_PFD2>, |
| <&clks IMX6SX_CLK_STEP>, |
| <&clks IMX6SX_CLK_PLL1_SW>, |
| <&clks IMX6SX_CLK_PLL1_SYS>; |
| clock-names = "arm", "pll2_pfd2_396m", "step", |
| "pll1_sw", "pll1_sys"; |
| arm-supply = <®_arm>; |
| soc-supply = <®_soc>; |
| }; |
| }; |
| |
| intc: interrupt-controller@00a01000 { |
| compatible = "arm,cortex-a9-gic"; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| reg = <0x00a01000 0x1000>, |
| <0x00a00100 0x100>; |
| interrupt-parent = <&intc>; |
| }; |
| |
| clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ckil: clock@0 { |
| compatible = "fixed-clock"; |
| reg = <0>; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| clock-output-names = "ckil"; |
| }; |
| |
| osc: clock@1 { |
| compatible = "fixed-clock"; |
| reg = <1>; |
| #clock-cells = <0>; |
| clock-frequency = <24000000>; |
| clock-output-names = "osc"; |
| }; |
| |
| ipp_di0: clock@2 { |
| compatible = "fixed-clock"; |
| reg = <2>; |
| #clock-cells = <0>; |
| clock-frequency = <0>; |
| clock-output-names = "ipp_di0"; |
| }; |
| |
| ipp_di1: clock@3 { |
| compatible = "fixed-clock"; |
| reg = <3>; |
| #clock-cells = <0>; |
| clock-frequency = <0>; |
| clock-output-names = "ipp_di1"; |
| }; |
| }; |
| |
| soc { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "simple-bus"; |
| interrupt-parent = <&gpc>; |
| ranges; |
| |
| pmu { |
| compatible = "arm,cortex-a9-pmu"; |
| interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| ocram: sram@00900000 { |
| compatible = "mmio-sram"; |
| reg = <0x00900000 0x20000>; |
| clocks = <&clks IMX6SX_CLK_OCRAM>; |
| }; |
| |
| L2: l2-cache@00a02000 { |
| compatible = "arm,pl310-cache"; |
| reg = <0x00a02000 0x1000>; |
| interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; |
| cache-unified; |
| cache-level = <2>; |
| arm,tag-latency = <4 2 3>; |
| arm,data-latency = <4 2 3>; |
| }; |
| |
| dma_apbh: dma-apbh@01804000 { |
| compatible = "fsl,imx6sx-dma-apbh", "fsl,imx28-dma-apbh"; |
| reg = <0x01804000 0x2000>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3"; |
| #dma-cells = <1>; |
| dma-channels = <4>; |
| clocks = <&clks IMX6SX_CLK_APBH_DMA>; |
| }; |
| |
| gpmi: gpmi-nand@01806000{ |
| compatible = "fsl,imx6sx-gpmi-nand"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x01806000 0x2000>, <0x01808000 0x4000>; |
| reg-names = "gpmi-nand", "bch"; |
| interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "bch"; |
| clocks = <&clks IMX6SX_CLK_GPMI_IO>, |
| <&clks IMX6SX_CLK_GPMI_APB>, |
| <&clks IMX6SX_CLK_GPMI_BCH>, |
| <&clks IMX6SX_CLK_GPMI_BCH_APB>, |
| <&clks IMX6SX_CLK_PER1_BCH>; |
| clock-names = "gpmi_io", "gpmi_apb", "gpmi_bch", |
| "gpmi_bch_apb", "per1_bch"; |
| dmas = <&dma_apbh 0>; |
| dma-names = "rx-tx"; |
| status = "disabled"; |
| }; |
| |
| aips1: aips-bus@02000000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x02000000 0x100000>; |
| ranges; |
| |
| spba-bus@02000000 { |
| compatible = "fsl,spba-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x02000000 0x40000>; |
| ranges; |
| |
| spdif: spdif@02004000 { |
| compatible = "fsl,imx6sx-spdif", "fsl,imx35-spdif"; |
| reg = <0x02004000 0x4000>; |
| interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&sdma 14 18 0>, |
| <&sdma 15 18 0>; |
| dma-names = "rx", "tx"; |
| clocks = <&clks IMX6SX_CLK_SPDIF_GCLK>, |
| <&clks IMX6SX_CLK_OSC>, |
| <&clks IMX6SX_CLK_SPDIF>, |
| <&clks 0>, <&clks 0>, <&clks 0>, |
| <&clks IMX6SX_CLK_IPG>, |
| <&clks 0>, <&clks 0>, |
| <&clks IMX6SX_CLK_SPBA>; |
| clock-names = "core", "rxtx0", |
| "rxtx1", "rxtx2", |
| "rxtx3", "rxtx4", |
| "rxtx5", "rxtx6", |
| "rxtx7", "spba"; |
| status = "disabled"; |
| }; |
| |
| ecspi1: ecspi@02008000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x02008000 0x4000>; |
| interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ECSPI1>, |
| <&clks IMX6SX_CLK_ECSPI1>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| ecspi2: ecspi@0200c000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x0200c000 0x4000>; |
| interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ECSPI2>, |
| <&clks IMX6SX_CLK_ECSPI2>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| ecspi3: ecspi@02010000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x02010000 0x4000>; |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ECSPI3>, |
| <&clks IMX6SX_CLK_ECSPI3>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| ecspi4: ecspi@02014000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x02014000 0x4000>; |
| interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ECSPI4>, |
| <&clks IMX6SX_CLK_ECSPI4>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| uart1: serial@02020000 { |
| compatible = "fsl,imx6sx-uart", "fsl,imx21-uart"; |
| reg = <0x02020000 0x4000>; |
| interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_UART_IPG>, |
| <&clks IMX6SX_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 25 4 0>, <&sdma 26 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| esai: esai@02024000 { |
| reg = <0x02024000 0x4000>; |
| interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ESAI_IPG>, |
| <&clks IMX6SX_CLK_ESAI_MEM>, |
| <&clks IMX6SX_CLK_ESAI_EXTAL>, |
| <&clks IMX6SX_CLK_ESAI_IPG>, |
| <&clks IMX6SX_CLK_SPBA>; |
| clock-names = "core", "mem", "extal", |
| "fsys", "spba"; |
| status = "disabled"; |
| }; |
| |
| ssi1: ssi@02028000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx6sx-ssi", "fsl,imx51-ssi"; |
| reg = <0x02028000 0x4000>; |
| interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_SSI1_IPG>, |
| <&clks IMX6SX_CLK_SSI1>; |
| clock-names = "ipg", "baud"; |
| dmas = <&sdma 37 1 0>, <&sdma 38 1 0>; |
| dma-names = "rx", "tx"; |
| fsl,fifo-depth = <15>; |
| status = "disabled"; |
| }; |
| |
| ssi2: ssi@0202c000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx6sx-ssi", "fsl,imx51-ssi"; |
| reg = <0x0202c000 0x4000>; |
| interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_SSI2_IPG>, |
| <&clks IMX6SX_CLK_SSI2>; |
| clock-names = "ipg", "baud"; |
| dmas = <&sdma 41 1 0>, <&sdma 42 1 0>; |
| dma-names = "rx", "tx"; |
| fsl,fifo-depth = <15>; |
| status = "disabled"; |
| }; |
| |
| ssi3: ssi@02030000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx6sx-ssi", "fsl,imx51-ssi"; |
| reg = <0x02030000 0x4000>; |
| interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_SSI3_IPG>, |
| <&clks IMX6SX_CLK_SSI3>; |
| clock-names = "ipg", "baud"; |
| dmas = <&sdma 45 1 0>, <&sdma 46 1 0>; |
| dma-names = "rx", "tx"; |
| fsl,fifo-depth = <15>; |
| status = "disabled"; |
| }; |
| |
| asrc: asrc@02034000 { |
| reg = <0x02034000 0x4000>; |
| interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ASRC_MEM>, |
| <&clks IMX6SX_CLK_ASRC_IPG>, |
| <&clks IMX6SX_CLK_SPDIF>, |
| <&clks IMX6SX_CLK_SPBA>; |
| clock-names = "mem", "ipg", "asrck", "spba"; |
| dmas = <&sdma 17 20 1>, <&sdma 18 20 1>, |
| <&sdma 19 20 1>, <&sdma 20 20 1>, |
| <&sdma 21 20 1>, <&sdma 22 20 1>; |
| dma-names = "rxa", "rxb", "rxc", |
| "txa", "txb", "txc"; |
| status = "okay"; |
| }; |
| }; |
| |
| pwm1: pwm@02080000 { |
| compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm"; |
| reg = <0x02080000 0x4000>; |
| interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PWM1>, |
| <&clks IMX6SX_CLK_PWM1>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <2>; |
| }; |
| |
| pwm2: pwm@02084000 { |
| compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm"; |
| reg = <0x02084000 0x4000>; |
| interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PWM2>, |
| <&clks IMX6SX_CLK_PWM2>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <2>; |
| }; |
| |
| pwm3: pwm@02088000 { |
| compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm"; |
| reg = <0x02088000 0x4000>; |
| interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PWM3>, |
| <&clks IMX6SX_CLK_PWM3>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <2>; |
| }; |
| |
| pwm4: pwm@0208c000 { |
| compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm"; |
| reg = <0x0208c000 0x4000>; |
| interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PWM4>, |
| <&clks IMX6SX_CLK_PWM4>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <2>; |
| }; |
| |
| flexcan1: can@02090000 { |
| compatible = "fsl,imx6sx-flexcan", "fsl,imx6q-flexcan"; |
| reg = <0x02090000 0x4000>; |
| interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_CAN1_IPG>, |
| <&clks IMX6SX_CLK_CAN1_SERIAL>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| flexcan2: can@02094000 { |
| compatible = "fsl,imx6sx-flexcan", "fsl,imx6q-flexcan"; |
| reg = <0x02094000 0x4000>; |
| interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_CAN2_IPG>, |
| <&clks IMX6SX_CLK_CAN2_SERIAL>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| gpt: gpt@02098000 { |
| compatible = "fsl,imx6sx-gpt", "fsl,imx31-gpt"; |
| reg = <0x02098000 0x4000>; |
| interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_GPT_BUS>, |
| <&clks IMX6SX_CLK_GPT_3M>; |
| clock-names = "ipg", "per"; |
| }; |
| |
| gpio1: gpio@0209c000 { |
| compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio"; |
| reg = <0x0209c000 0x4000>; |
| interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio2: gpio@020a0000 { |
| compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio"; |
| reg = <0x020a0000 0x4000>; |
| interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio3: gpio@020a4000 { |
| compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio"; |
| reg = <0x020a4000 0x4000>; |
| interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio4: gpio@020a8000 { |
| compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio"; |
| reg = <0x020a8000 0x4000>; |
| interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio5: gpio@020ac000 { |
| compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio"; |
| reg = <0x020ac000 0x4000>; |
| interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio6: gpio@020b0000 { |
| compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio"; |
| reg = <0x020b0000 0x4000>; |
| interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio7: gpio@020b4000 { |
| compatible = "fsl,imx6sx-gpio", "fsl,imx35-gpio"; |
| reg = <0x020b4000 0x4000>; |
| interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| kpp: kpp@020b8000 { |
| compatible = "fsl,imx6sx-kpp", "fsl,imx21-kpp"; |
| reg = <0x020b8000 0x4000>; |
| interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_DUMMY>; |
| status = "disabled"; |
| }; |
| |
| wdog1: wdog@020bc000 { |
| compatible = "fsl,imx6sx-wdt", "fsl,imx21-wdt"; |
| reg = <0x020bc000 0x4000>; |
| interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_DUMMY>; |
| }; |
| |
| wdog2: wdog@020c0000 { |
| compatible = "fsl,imx6sx-wdt", "fsl,imx21-wdt"; |
| reg = <0x020c0000 0x4000>; |
| interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_DUMMY>; |
| status = "disabled"; |
| }; |
| |
| clks: ccm@020c4000 { |
| compatible = "fsl,imx6sx-ccm"; |
| reg = <0x020c4000 0x4000>; |
| interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; |
| #clock-cells = <1>; |
| clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>; |
| clock-names = "ckil", "osc", "ipp_di0", "ipp_di1"; |
| }; |
| |
| anatop: anatop@020c8000 { |
| compatible = "fsl,imx6sx-anatop", "fsl,imx6q-anatop", |
| "syscon", "simple-bus"; |
| reg = <0x020c8000 0x1000>; |
| interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; |
| |
| regulator-1p1@110 { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vdd1p1"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1375000>; |
| regulator-always-on; |
| anatop-reg-offset = <0x110>; |
| anatop-vol-bit-shift = <8>; |
| anatop-vol-bit-width = <5>; |
| anatop-min-bit-val = <4>; |
| anatop-min-voltage = <800000>; |
| anatop-max-voltage = <1375000>; |
| }; |
| |
| regulator-3p0@120 { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vdd3p0"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <3150000>; |
| regulator-always-on; |
| anatop-reg-offset = <0x120>; |
| anatop-vol-bit-shift = <8>; |
| anatop-vol-bit-width = <5>; |
| anatop-min-bit-val = <0>; |
| anatop-min-voltage = <2625000>; |
| anatop-max-voltage = <3400000>; |
| }; |
| |
| regulator-2p5@130 { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vdd2p5"; |
| regulator-min-microvolt = <2100000>; |
| regulator-max-microvolt = <2875000>; |
| regulator-always-on; |
| anatop-reg-offset = <0x130>; |
| anatop-vol-bit-shift = <8>; |
| anatop-vol-bit-width = <5>; |
| anatop-min-bit-val = <0>; |
| anatop-min-voltage = <2100000>; |
| anatop-max-voltage = <2875000>; |
| }; |
| |
| reg_arm: regulator-vddcore@140 { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vddarm"; |
| regulator-min-microvolt = <725000>; |
| regulator-max-microvolt = <1450000>; |
| regulator-always-on; |
| anatop-reg-offset = <0x140>; |
| anatop-vol-bit-shift = <0>; |
| anatop-vol-bit-width = <5>; |
| anatop-delay-reg-offset = <0x170>; |
| anatop-delay-bit-shift = <24>; |
| anatop-delay-bit-width = <2>; |
| anatop-min-bit-val = <1>; |
| anatop-min-voltage = <725000>; |
| anatop-max-voltage = <1450000>; |
| }; |
| |
| reg_pcie: regulator-vddpcie@140 { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vddpcie"; |
| regulator-min-microvolt = <725000>; |
| regulator-max-microvolt = <1450000>; |
| anatop-reg-offset = <0x140>; |
| anatop-vol-bit-shift = <9>; |
| anatop-vol-bit-width = <5>; |
| anatop-delay-reg-offset = <0x170>; |
| anatop-delay-bit-shift = <26>; |
| anatop-delay-bit-width = <2>; |
| anatop-min-bit-val = <1>; |
| anatop-min-voltage = <725000>; |
| anatop-max-voltage = <1450000>; |
| }; |
| |
| reg_soc: regulator-vddsoc@140 { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vddsoc"; |
| regulator-min-microvolt = <725000>; |
| regulator-max-microvolt = <1450000>; |
| regulator-always-on; |
| anatop-reg-offset = <0x140>; |
| anatop-vol-bit-shift = <18>; |
| anatop-vol-bit-width = <5>; |
| anatop-delay-reg-offset = <0x170>; |
| anatop-delay-bit-shift = <28>; |
| anatop-delay-bit-width = <2>; |
| anatop-min-bit-val = <1>; |
| anatop-min-voltage = <725000>; |
| anatop-max-voltage = <1450000>; |
| }; |
| }; |
| |
| tempmon: tempmon { |
| compatible = "fsl,imx6sx-tempmon", "fsl,imx6q-tempmon"; |
| interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; |
| fsl,tempmon = <&anatop>; |
| fsl,tempmon-data = <&ocotp>; |
| clocks = <&clks IMX6SX_CLK_PLL3_USB_OTG>; |
| }; |
| |
| usbphy1: usbphy@020c9000 { |
| compatible = "fsl,imx6sx-usbphy", "fsl,imx23-usbphy"; |
| reg = <0x020c9000 0x1000>; |
| interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USBPHY1>; |
| fsl,anatop = <&anatop>; |
| }; |
| |
| usbphy2: usbphy@020ca000 { |
| compatible = "fsl,imx6sx-usbphy", "fsl,imx23-usbphy"; |
| reg = <0x020ca000 0x1000>; |
| interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USBPHY2>; |
| fsl,anatop = <&anatop>; |
| }; |
| |
| snvs: snvs@020cc000 { |
| compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd"; |
| reg = <0x020cc000 0x4000>; |
| |
| snvs_rtc: snvs-rtc-lp { |
| compatible = "fsl,sec-v4.0-mon-rtc-lp"; |
| regmap = <&snvs>; |
| offset = <0x34>; |
| interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| snvs_poweroff: snvs-poweroff { |
| compatible = "syscon-poweroff"; |
| regmap = <&snvs>; |
| offset = <0x38>; |
| mask = <0x60>; |
| status = "disabled"; |
| }; |
| |
| snvs_pwrkey: snvs-powerkey { |
| compatible = "fsl,sec-v4.0-pwrkey"; |
| regmap = <&snvs>; |
| interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; |
| linux,keycode = <KEY_POWER>; |
| wakeup-source; |
| }; |
| }; |
| |
| epit1: epit@020d0000 { |
| reg = <0x020d0000 0x4000>; |
| interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| epit2: epit@020d4000 { |
| reg = <0x020d4000 0x4000>; |
| interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| src: src@020d8000 { |
| compatible = "fsl,imx6sx-src", "fsl,imx51-src"; |
| reg = <0x020d8000 0x4000>; |
| interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| #reset-cells = <1>; |
| }; |
| |
| gpc: gpc@020dc000 { |
| compatible = "fsl,imx6sx-gpc", "fsl,imx6q-gpc"; |
| reg = <0x020dc000 0x4000>; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-parent = <&intc>; |
| }; |
| |
| iomuxc: iomuxc@020e0000 { |
| compatible = "fsl,imx6sx-iomuxc"; |
| reg = <0x020e0000 0x4000>; |
| }; |
| |
| gpr: iomuxc-gpr@020e4000 { |
| compatible = "fsl,imx6sx-iomuxc-gpr", |
| "fsl,imx6q-iomuxc-gpr", "syscon"; |
| reg = <0x020e4000 0x4000>; |
| }; |
| |
| sdma: sdma@020ec000 { |
| compatible = "fsl,imx6sx-sdma", "fsl,imx6q-sdma"; |
| reg = <0x020ec000 0x4000>; |
| interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_SDMA>, |
| <&clks IMX6SX_CLK_SDMA>; |
| clock-names = "ipg", "ahb"; |
| #dma-cells = <3>; |
| /* imx6sx reuses imx6q sdma firmware */ |
| fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6q.bin"; |
| }; |
| }; |
| |
| aips2: aips-bus@02100000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x02100000 0x100000>; |
| ranges; |
| |
| crypto: caam@2100000 { |
| compatible = "fsl,sec-v4.0"; |
| fsl,sec-era = <4>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x2100000 0x10000>; |
| ranges = <0 0x2100000 0x10000>; |
| interrupt-parent = <&intc>; |
| clocks = <&clks IMX6SX_CLK_CAAM_MEM>, |
| <&clks IMX6SX_CLK_CAAM_ACLK>, |
| <&clks IMX6SX_CLK_CAAM_IPG>, |
| <&clks IMX6SX_CLK_EIM_SLOW>; |
| clock-names = "mem", "aclk", "ipg", "emi_slow"; |
| |
| sec_jr0: jr0@1000 { |
| compatible = "fsl,sec-v4.0-job-ring"; |
| reg = <0x1000 0x1000>; |
| interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| sec_jr1: jr1@2000 { |
| compatible = "fsl,sec-v4.0-job-ring"; |
| reg = <0x2000 0x1000>; |
| interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| usbotg1: usb@02184000 { |
| compatible = "fsl,imx6sx-usb", "fsl,imx27-usb"; |
| reg = <0x02184000 0x200>; |
| interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USBOH3>; |
| fsl,usbphy = <&usbphy1>; |
| fsl,usbmisc = <&usbmisc 0>; |
| fsl,anatop = <&anatop>; |
| ahb-burst-config = <0x0>; |
| tx-burst-size-dword = <0x10>; |
| rx-burst-size-dword = <0x10>; |
| status = "disabled"; |
| }; |
| |
| usbotg2: usb@02184200 { |
| compatible = "fsl,imx6sx-usb", "fsl,imx27-usb"; |
| reg = <0x02184200 0x200>; |
| interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USBOH3>; |
| fsl,usbphy = <&usbphy2>; |
| fsl,usbmisc = <&usbmisc 1>; |
| ahb-burst-config = <0x0>; |
| tx-burst-size-dword = <0x10>; |
| rx-burst-size-dword = <0x10>; |
| status = "disabled"; |
| }; |
| |
| usbh: usb@02184400 { |
| compatible = "fsl,imx6sx-usb", "fsl,imx27-usb"; |
| reg = <0x02184400 0x200>; |
| interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USBOH3>; |
| fsl,usbmisc = <&usbmisc 2>; |
| phy_type = "hsic"; |
| fsl,anatop = <&anatop>; |
| dr_mode = "host"; |
| ahb-burst-config = <0x0>; |
| tx-burst-size-dword = <0x10>; |
| rx-burst-size-dword = <0x10>; |
| status = "disabled"; |
| }; |
| |
| usbmisc: usbmisc@02184800 { |
| #index-cells = <1>; |
| compatible = "fsl,imx6sx-usbmisc", "fsl,imx6q-usbmisc"; |
| reg = <0x02184800 0x200>; |
| clocks = <&clks IMX6SX_CLK_USBOH3>; |
| }; |
| |
| fec1: ethernet@02188000 { |
| compatible = "fsl,imx6sx-fec", "fsl,imx6q-fec"; |
| reg = <0x02188000 0x4000>; |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ENET>, |
| <&clks IMX6SX_CLK_ENET_AHB>, |
| <&clks IMX6SX_CLK_ENET_PTP>, |
| <&clks IMX6SX_CLK_ENET_REF>, |
| <&clks IMX6SX_CLK_ENET_PTP>; |
| clock-names = "ipg", "ahb", "ptp", |
| "enet_clk_ref", "enet_out"; |
| fsl,num-tx-queues=<3>; |
| fsl,num-rx-queues=<3>; |
| status = "disabled"; |
| }; |
| |
| mlb: mlb@0218c000 { |
| reg = <0x0218c000 0x4000>; |
| interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_MLB>; |
| status = "disabled"; |
| }; |
| |
| usdhc1: usdhc@02190000 { |
| compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc"; |
| reg = <0x02190000 0x4000>; |
| interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USDHC1>, |
| <&clks IMX6SX_CLK_USDHC1>, |
| <&clks IMX6SX_CLK_USDHC1>; |
| clock-names = "ipg", "ahb", "per"; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| usdhc2: usdhc@02194000 { |
| compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc"; |
| reg = <0x02194000 0x4000>; |
| interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USDHC2>, |
| <&clks IMX6SX_CLK_USDHC2>, |
| <&clks IMX6SX_CLK_USDHC2>; |
| clock-names = "ipg", "ahb", "per"; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| usdhc3: usdhc@02198000 { |
| compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc"; |
| reg = <0x02198000 0x4000>; |
| interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USDHC3>, |
| <&clks IMX6SX_CLK_USDHC3>, |
| <&clks IMX6SX_CLK_USDHC3>; |
| clock-names = "ipg", "ahb", "per"; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| usdhc4: usdhc@0219c000 { |
| compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc"; |
| reg = <0x0219c000 0x4000>; |
| interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_USDHC4>, |
| <&clks IMX6SX_CLK_USDHC4>, |
| <&clks IMX6SX_CLK_USDHC4>; |
| clock-names = "ipg", "ahb", "per"; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@021a0000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-i2c", "fsl,imx21-i2c"; |
| reg = <0x021a0000 0x4000>; |
| interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_I2C1>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@021a4000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-i2c", "fsl,imx21-i2c"; |
| reg = <0x021a4000 0x4000>; |
| interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_I2C2>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@021a8000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-i2c", "fsl,imx21-i2c"; |
| reg = <0x021a8000 0x4000>; |
| interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_I2C3>; |
| status = "disabled"; |
| }; |
| |
| mmdc: mmdc@021b0000 { |
| compatible = "fsl,imx6sx-mmdc", "fsl,imx6q-mmdc"; |
| reg = <0x021b0000 0x4000>; |
| }; |
| |
| fec2: ethernet@021b4000 { |
| compatible = "fsl,imx6sx-fec", "fsl,imx6q-fec"; |
| reg = <0x021b4000 0x4000>; |
| interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ENET>, |
| <&clks IMX6SX_CLK_ENET_AHB>, |
| <&clks IMX6SX_CLK_ENET_PTP>, |
| <&clks IMX6SX_CLK_ENET2_REF_125M>, |
| <&clks IMX6SX_CLK_ENET_PTP>; |
| clock-names = "ipg", "ahb", "ptp", |
| "enet_clk_ref", "enet_out"; |
| status = "disabled"; |
| }; |
| |
| weim: weim@021b8000 { |
| compatible = "fsl,imx6sx-weim", "fsl,imx6q-weim"; |
| reg = <0x021b8000 0x4000>; |
| interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_EIM_SLOW>; |
| }; |
| |
| ocotp: ocotp@021bc000 { |
| compatible = "fsl,imx6sx-ocotp", "syscon"; |
| reg = <0x021bc000 0x4000>; |
| clocks = <&clks IMX6SX_CLK_OCOTP>; |
| }; |
| |
| sai1: sai@021d4000 { |
| compatible = "fsl,imx6sx-sai"; |
| reg = <0x021d4000 0x4000>; |
| interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_SAI1_IPG>, |
| <&clks IMX6SX_CLK_SAI1>, |
| <&clks 0>, <&clks 0>; |
| clock-names = "bus", "mclk1", "mclk2", "mclk3"; |
| dma-names = "rx", "tx"; |
| dmas = <&sdma 31 24 0>, <&sdma 32 24 0>; |
| status = "disabled"; |
| }; |
| |
| audmux: audmux@021d8000 { |
| compatible = "fsl,imx6sx-audmux", "fsl,imx31-audmux"; |
| reg = <0x021d8000 0x4000>; |
| status = "disabled"; |
| }; |
| |
| sai2: sai@021dc000 { |
| compatible = "fsl,imx6sx-sai"; |
| reg = <0x021dc000 0x4000>; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_SAI2_IPG>, |
| <&clks IMX6SX_CLK_SAI2>, |
| <&clks 0>, <&clks 0>; |
| clock-names = "bus", "mclk1", "mclk2", "mclk3"; |
| dma-names = "rx", "tx"; |
| dmas = <&sdma 33 24 0>, <&sdma 34 24 0>; |
| status = "disabled"; |
| }; |
| |
| qspi1: qspi@021e0000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-qspi"; |
| reg = <0x021e0000 0x4000>, <0x60000000 0x10000000>; |
| reg-names = "QuadSPI", "QuadSPI-memory"; |
| interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_QSPI1>, |
| <&clks IMX6SX_CLK_QSPI1>; |
| clock-names = "qspi_en", "qspi"; |
| status = "disabled"; |
| }; |
| |
| qspi2: qspi@021e4000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-qspi"; |
| reg = <0x021e4000 0x4000>, <0x70000000 0x10000000>; |
| reg-names = "QuadSPI", "QuadSPI-memory"; |
| interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_QSPI2>, |
| <&clks IMX6SX_CLK_QSPI2>; |
| clock-names = "qspi_en", "qspi"; |
| status = "disabled"; |
| }; |
| |
| uart2: serial@021e8000 { |
| compatible = "fsl,imx6sx-uart", "fsl,imx21-uart"; |
| reg = <0x021e8000 0x4000>; |
| interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_UART_IPG>, |
| <&clks IMX6SX_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 27 4 0>, <&sdma 28 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart3: serial@021ec000 { |
| compatible = "fsl,imx6sx-uart", "fsl,imx21-uart"; |
| reg = <0x021ec000 0x4000>; |
| interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_UART_IPG>, |
| <&clks IMX6SX_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 29 4 0>, <&sdma 30 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@021f0000 { |
| compatible = "fsl,imx6sx-uart", "fsl,imx21-uart"; |
| reg = <0x021f0000 0x4000>; |
| interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_UART_IPG>, |
| <&clks IMX6SX_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 31 4 0>, <&sdma 32 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart5: serial@021f4000 { |
| compatible = "fsl,imx6sx-uart", "fsl,imx21-uart"; |
| reg = <0x021f4000 0x4000>; |
| interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_UART_IPG>, |
| <&clks IMX6SX_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 33 4 0>, <&sdma 34 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@021f8000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-i2c", "fsl,imx21-i2c"; |
| reg = <0x021f8000 0x4000>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_I2C4>; |
| status = "disabled"; |
| }; |
| }; |
| |
| aips3: aips-bus@02200000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x02200000 0x100000>; |
| ranges; |
| |
| spba-bus@02200000 { |
| compatible = "fsl,spba-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x02240000 0x40000>; |
| ranges; |
| |
| csi1: csi@02214000 { |
| reg = <0x02214000 0x4000>; |
| interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_DISPLAY_AXI>, |
| <&clks IMX6SX_CLK_CSI>, |
| <&clks IMX6SX_CLK_DCIC1>; |
| clock-names = "disp-axi", "csi_mclk", "dcic"; |
| status = "disabled"; |
| }; |
| |
| pxp: pxp@02218000 { |
| reg = <0x02218000 0x4000>; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PXP_AXI>, |
| <&clks IMX6SX_CLK_DISPLAY_AXI>; |
| clock-names = "pxp-axi", "disp-axi"; |
| status = "disabled"; |
| }; |
| |
| csi2: csi@0221c000 { |
| reg = <0x0221c000 0x4000>; |
| interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_DISPLAY_AXI>, |
| <&clks IMX6SX_CLK_CSI>, |
| <&clks IMX6SX_CLK_DCIC2>; |
| clock-names = "disp-axi", "csi_mclk", "dcic"; |
| status = "disabled"; |
| }; |
| |
| lcdif1: lcdif@02220000 { |
| compatible = "fsl,imx6sx-lcdif", "fsl,imx28-lcdif"; |
| reg = <0x02220000 0x4000>; |
| interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_LCDIF1_PIX>, |
| <&clks IMX6SX_CLK_LCDIF_APB>, |
| <&clks IMX6SX_CLK_DISPLAY_AXI>; |
| clock-names = "pix", "axi", "disp_axi"; |
| status = "disabled"; |
| }; |
| |
| lcdif2: lcdif@02224000 { |
| compatible = "fsl,imx6sx-lcdif", "fsl,imx28-lcdif"; |
| reg = <0x02224000 0x4000>; |
| interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_LCDIF2_PIX>, |
| <&clks IMX6SX_CLK_LCDIF_APB>, |
| <&clks IMX6SX_CLK_DISPLAY_AXI>; |
| clock-names = "pix", "axi", "disp_axi"; |
| status = "disabled"; |
| }; |
| |
| vadc: vadc@02228000 { |
| reg = <0x02228000 0x4000>, <0x0222c000 0x4000>; |
| reg-names = "vadc-vafe", "vadc-vdec"; |
| clocks = <&clks IMX6SX_CLK_VADC>, |
| <&clks IMX6SX_CLK_CSI>; |
| clock-names = "vadc", "csi"; |
| status = "disabled"; |
| }; |
| }; |
| |
| adc1: adc@02280000 { |
| compatible = "fsl,imx6sx-adc", "fsl,vf610-adc"; |
| reg = <0x02280000 0x4000>; |
| interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_IPG>; |
| clock-names = "adc"; |
| fsl,adck-max-frequency = <30000000>, <40000000>, |
| <20000000>; |
| status = "disabled"; |
| }; |
| |
| adc2: adc@02284000 { |
| compatible = "fsl,imx6sx-adc", "fsl,vf610-adc"; |
| reg = <0x02284000 0x4000>; |
| interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_IPG>; |
| clock-names = "adc"; |
| fsl,adck-max-frequency = <30000000>, <40000000>, |
| <20000000>; |
| status = "disabled"; |
| }; |
| |
| wdog3: wdog@02288000 { |
| compatible = "fsl,imx6sx-wdt", "fsl,imx21-wdt"; |
| reg = <0x02288000 0x4000>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_DUMMY>; |
| status = "disabled"; |
| }; |
| |
| ecspi5: ecspi@0228c000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6sx-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x0228c000 0x4000>; |
| interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_ECSPI5>, |
| <&clks IMX6SX_CLK_ECSPI5>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| uart6: serial@022a0000 { |
| compatible = "fsl,imx6sx-uart", "fsl,imx21-uart"; |
| reg = <0x022a0000 0x4000>; |
| interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_UART_IPG>, |
| <&clks IMX6SX_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 0 4 0>, <&sdma 47 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| pwm5: pwm@022a4000 { |
| compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm"; |
| reg = <0x022a4000 0x4000>; |
| interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PWM5>, |
| <&clks IMX6SX_CLK_PWM5>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <2>; |
| }; |
| |
| pwm6: pwm@022a8000 { |
| compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm"; |
| reg = <0x022a8000 0x4000>; |
| interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PWM6>, |
| <&clks IMX6SX_CLK_PWM6>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <2>; |
| }; |
| |
| pwm7: pwm@022ac000 { |
| compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm"; |
| reg = <0x022ac000 0x4000>; |
| interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PWM7>, |
| <&clks IMX6SX_CLK_PWM7>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <2>; |
| }; |
| |
| pwm8: pwm@0022b0000 { |
| compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm"; |
| reg = <0x0022b0000 0x4000>; |
| interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PWM8>, |
| <&clks IMX6SX_CLK_PWM8>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <2>; |
| }; |
| }; |
| |
| pcie: pcie@0x08000000 { |
| compatible = "fsl,imx6sx-pcie", "snps,dw-pcie"; |
| reg = <0x08ffc000 0x4000>; /* DBI */ |
| #address-cells = <3>; |
| #size-cells = <2>; |
| device_type = "pci"; |
| /* configuration space */ |
| ranges = <0x00000800 0 0x08f00000 0x08f00000 0 0x00080000 |
| /* downstream I/O */ |
| 0x81000000 0 0 0x08f80000 0 0x00010000 |
| /* non-prefetchable memory */ |
| 0x82000000 0 0x08000000 0x08000000 0 0x00f00000>; |
| num-lanes = <1>; |
| interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6SX_CLK_PCIE_REF_125M>, |
| <&clks IMX6SX_CLK_PCIE_AXI>, |
| <&clks IMX6SX_CLK_LVDS1_OUT>, |
| <&clks IMX6SX_CLK_DISPLAY_AXI>; |
| clock-names = "pcie_ref_125m", "pcie_axi", |
| "lvds_gate", "display_axi"; |
| status = "disabled"; |
| }; |
| }; |
| }; |
