| /* |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| /dts-v1/; |
| |
| #include "dm816x.dtsi" |
| #include <dt-bindings/interrupt-controller/irq.h> |
| |
| / { |
| model = "DM8168 EVM"; |
| compatible = "ti,dm8168-evm", "ti,dm8168"; |
| |
| memory { |
| device_type = "memory"; |
| reg = <0x80000000 0x40000000 /* 1 GB */ |
| 0xc0000000 0x40000000>; /* 1 GB */ |
| }; |
| |
| /* FDC6331L controlled by SD_POW pin */ |
| vmmcsd_fixed: fixedregulator@0 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vmmcsd_fixed"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| }; |
| |
| &dm816x_pinmux { |
| mcspi1_pins: pinmux_mcspi1_pins { |
| pinctrl-single,pins = < |
| DM816X_IOPAD(0x0a94, MUX_MODE0) /* SPI_SCLK */ |
| DM816X_IOPAD(0x0a98, MUX_MODE0) /* SPI_SCS0 */ |
| DM816X_IOPAD(0x0aa8, MUX_MODE0) /* SPI_D0 */ |
| DM816X_IOPAD(0x0aac, MUX_MODE0) /* SPI_D1 */ |
| >; |
| }; |
| |
| mmc_pins: pinmux_mmc_pins { |
| pinctrl-single,pins = < |
| DM816X_IOPAD(0x0a70, MUX_MODE0) /* SD_POW */ |
| DM816X_IOPAD(0x0a74, MUX_MODE0) /* SD_CLK */ |
| DM816X_IOPAD(0x0a78, MUX_MODE0) /* SD_CMD */ |
| DM816X_IOPAD(0x0a7C, MUX_MODE0) /* SD_DAT0 */ |
| DM816X_IOPAD(0x0a80, MUX_MODE0) /* SD_DAT1 */ |
| DM816X_IOPAD(0x0a84, MUX_MODE0) /* SD_DAT2 */ |
| DM816X_IOPAD(0x0a88, MUX_MODE0) /* SD_DAT2 */ |
| DM816X_IOPAD(0x0a8c, MUX_MODE2) /* GP1[7] */ |
| DM816X_IOPAD(0x0a90, MUX_MODE2) /* GP1[8] */ |
| >; |
| }; |
| |
| usb0_pins: pinmux_usb0_pins { |
| pinctrl-single,pins = < |
| DM816X_IOPAD(0x0d04, MUX_MODE0) /* USB0_DRVVBUS */ |
| >; |
| }; |
| |
| usb1_pins: pinmux_usb1_pins { |
| pinctrl-single,pins = < |
| DM816X_IOPAD(0x0d08, MUX_MODE0) /* USB1_DRVVBUS */ |
| >; |
| }; |
| }; |
| |
| &i2c1 { |
| extgpio0: pcf8575@20 { |
| compatible = "nxp,pcf8575"; |
| reg = <0x20>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| }; |
| |
| &i2c2 { |
| extgpio1: pcf8575@20 { |
| compatible = "nxp,pcf8575"; |
| reg = <0x20>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| }; |
| |
| &gpmc { |
| ranges = <0 0 0x04000000 0x01000000>; /* CS0: 16MB for NAND */ |
| |
| nand@0,0 { |
| compatible = "ti,omap2-nand"; |
| linux,mtd-name= "micron,mt29f2g16aadwp"; |
| reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ |
| interrupt-parent = <&gpmc>; |
| interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ |
| <1 IRQ_TYPE_NONE>; /* termcount */ |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ti,nand-ecc-opt = "bch8"; |
| nand-bus-width = <16>; |
| gpmc,device-width = <2>; |
| gpmc,sync-clk-ps = <0>; |
| gpmc,cs-on-ns = <0>; |
| gpmc,cs-rd-off-ns = <44>; |
| gpmc,cs-wr-off-ns = <44>; |
| gpmc,adv-on-ns = <6>; |
| gpmc,adv-rd-off-ns = <34>; |
| gpmc,adv-wr-off-ns = <44>; |
| gpmc,we-on-ns = <0>; |
| gpmc,we-off-ns = <40>; |
| gpmc,oe-on-ns = <0>; |
| gpmc,oe-off-ns = <54>; |
| gpmc,access-ns = <64>; |
| gpmc,rd-cycle-ns = <82>; |
| gpmc,wr-cycle-ns = <82>; |
| gpmc,bus-turnaround-ns = <0>; |
| gpmc,cycle2cycle-delay-ns = <0>; |
| gpmc,clk-activation-ns = <0>; |
| gpmc,wr-access-ns = <40>; |
| gpmc,wr-data-mux-bus-ns = <0>; |
| partition@0 { |
| label = "X-Loader"; |
| reg = <0 0x80000>; |
| }; |
| partition@0x80000 { |
| label = "U-Boot"; |
| reg = <0x80000 0x1c0000>; |
| }; |
| partition@0x1c0000 { |
| label = "Environment"; |
| reg = <0x240000 0x40000>; |
| }; |
| partition@0x280000 { |
| label = "Kernel"; |
| reg = <0x280000 0x500000>; |
| }; |
| partition@0x780000 { |
| label = "Filesystem"; |
| reg = <0x780000 0xf880000>; |
| }; |
| }; |
| }; |
| |
| &mcspi1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcspi1_pins>; |
| |
| m25p80@0 { |
| compatible = "w25x32"; |
| spi-max-frequency = <48000000>; |
| reg = <0>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| }; |
| }; |
| |
| &mmc1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc_pins>; |
| vmmc-supply = <&vmmcsd_fixed>; |
| bus-width = <4>; |
| cd-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>; |
| wp-gpios = <&gpio2 8 GPIO_ACTIVE_LOW>; |
| }; |
| |
| /* At least dm8168-evm rev c won't support multipoint, later may */ |
| &usb0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb0_pins>; |
| mentor,multipoint = <0>; |
| }; |
| |
| &usb1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb1_pins>; |
| mentor,multipoint = <0>; |
| }; |