| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| |
| #include "skeleton.dtsi" |
| |
| / { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| model = "Broadcom STB (bcm7445)"; |
| compatible = "brcm,bcm7445", "brcm,brcmstb"; |
| interrupt-parent = <&gic>; |
| |
| chosen { |
| bootargs = "console=ttyS0,115200 earlyprintk"; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu@0 { |
| compatible = "brcm,brahma-b15"; |
| device_type = "cpu"; |
| enable-method = "brcm,brahma-b15"; |
| reg = <0>; |
| }; |
| |
| cpu@1 { |
| compatible = "brcm,brahma-b15"; |
| device_type = "cpu"; |
| enable-method = "brcm,brahma-b15"; |
| reg = <1>; |
| }; |
| |
| cpu@2 { |
| compatible = "brcm,brahma-b15"; |
| device_type = "cpu"; |
| enable-method = "brcm,brahma-b15"; |
| reg = <2>; |
| }; |
| |
| cpu@3 { |
| compatible = "brcm,brahma-b15"; |
| device_type = "cpu"; |
| enable-method = "brcm,brahma-b15"; |
| reg = <3>; |
| }; |
| }; |
| |
| gic: interrupt-controller@ffd00000 { |
| compatible = "brcm,brahma-b15-gic", "arm,cortex-a15-gic"; |
| reg = <0x00 0xffd01000 0x00 0x1000>, |
| <0x00 0xffd02000 0x00 0x2000>, |
| <0x00 0xffd04000 0x00 0x2000>, |
| <0x00 0xffd06000 0x00 0x2000>; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| }; |
| |
| timer { |
| compatible = "arm,armv7-timer"; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 14 (GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 11 (GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 10 (GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>; |
| }; |
| |
| rdb { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "simple-bus"; |
| ranges = <0 0x00 0xf0000000 0x1000000>; |
| |
| serial@40ab00 { |
| compatible = "ns16550a"; |
| reg = <0x40ab00 0x20>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; |
| clock-frequency = <81000000>; |
| }; |
| |
| sun_top_ctrl: syscon@404000 { |
| compatible = "brcm,bcm7445-sun-top-ctrl", |
| "syscon"; |
| reg = <0x404000 0x51c>; |
| }; |
| |
| hif_cpubiuctrl: syscon@3e2400 { |
| compatible = "brcm,bcm7445-hif-cpubiuctrl", |
| "syscon"; |
| reg = <0x3e2400 0x5b4>; |
| }; |
| |
| hif_continuation: syscon@452000 { |
| compatible = "brcm,bcm7445-hif-continuation", |
| "syscon"; |
| reg = <0x452000 0x100>; |
| }; |
| |
| irq0_intc: interrupt-controller@40a780 { |
| compatible = "brcm,bcm7120-l2-intc"; |
| interrupt-parent = <&gic>; |
| #interrupt-cells = <1>; |
| reg = <0x40a780 0x8>; |
| interrupt-controller; |
| interrupts = <GIC_SPI 0x45 0x0>, |
| <GIC_SPI 0x43 0x0>; |
| brcm,int-map-mask = <0x25c>, <0x7000000>; |
| brcm,int-fwd-mask = <0x70000>; |
| }; |
| |
| irq0_aon_intc: interrupt-controller@417280 { |
| compatible = "brcm,bcm7120-l2-intc"; |
| reg = <0x417280 0x8>; |
| interrupt-parent = <&gic>; |
| #interrupt-cells = <1>; |
| interrupt-controller; |
| interrupts = <GIC_SPI 0x46 0x0>, |
| <GIC_SPI 0x44 0x0>, |
| <GIC_SPI 0x49 0x0>; |
| brcm,int-map-mask = <0x1e3 0x18000000 0x100000>; |
| brcm,int-fwd-mask = <0x0>; |
| brcm,irq-can-wake; |
| }; |
| |
| hif_intr2_intc: interrupt-controller@3e1000 { |
| compatible = "brcm,l2-intc"; |
| reg = <0x3e1000 0x30>; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| interrupts = <GIC_SPI 0x20 0x0>; |
| interrupt-parent = <&gic>; |
| interrupt-names = "hif"; |
| }; |
| |
| aon_pm_l2_intc: interrupt-controller@410640 { |
| compatible = "brcm,l2-intc"; |
| reg = <0x410640 0x30>; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| interrupts = <GIC_SPI 0x40 0x0>; |
| interrupt-parent = <&gic>; |
| brcm,irq-can-wake; |
| }; |
| |
| aon-ctrl@410000 { |
| compatible = "brcm,brcmstb-aon-ctrl"; |
| reg = <0x410000 0x200>, <0x410200 0x400>; |
| reg-names = "aon-ctrl", "aon-sram"; |
| }; |
| |
| nand: nand@3e2800 { |
| status = "disabled"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "brcm,brcmnand-v7.1", "brcm,brcmnand"; |
| reg-names = "nand", "flash-dma"; |
| reg = <0x3e2800 0x600>, <0x3e3000 0x2c>; |
| interrupt-parent = <&hif_intr2_intc>; |
| interrupts = <24>, <4>; |
| interrupt-names = "nand_ctlrdy", "flash_dma_done"; |
| }; |
| |
| sata@45a000 { |
| compatible = "brcm,bcm7445-ahci", "brcm,sata3-ahci"; |
| reg-names = "ahci", "top-ctrl"; |
| reg = <0x45a000 0xa9c>, <0x458040 0x24>; |
| interrupts = <GIC_SPI 30 0>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| sata0: sata-port@0 { |
| reg = <0>; |
| phys = <&sata_phy0>; |
| }; |
| |
| sata1: sata-port@1 { |
| reg = <1>; |
| phys = <&sata_phy1>; |
| }; |
| }; |
| |
| sata_phy: sata-phy@458100 { |
| compatible = "brcm,bcm7445-sata-phy", "brcm,phy-sata3"; |
| reg = <0x458100 0x1f00>; |
| reg-names = "phy"; |
| #address-cells = <0x1>; |
| #size-cells = <0x0>; |
| |
| sata_phy0: sata-phy@0 { |
| reg = <0>; |
| #phy-cells = <0>; |
| }; |
| |
| sata_phy1: sata-phy@1 { |
| reg = <1>; |
| #phy-cells = <0>; |
| }; |
| }; |
| |
| upg_gio: gpio@40a700 { |
| compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio"; |
| reg = <0x40a700 0x80>; |
| #gpio-cells = <2>; |
| #interrupt-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| interrupt-parent = <&irq0_intc>; |
| interrupts = <6>; |
| brcm,gpio-bank-widths = <32 32 32 24>; |
| }; |
| |
| upg_gio_aon: gpio@4172c0 { |
| compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio"; |
| reg = <0x4172c0 0x40>; |
| #gpio-cells = <2>; |
| #interrupt-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| interrupts-extended = <&irq0_aon_intc 0x6>, |
| <&aon_pm_l2_intc 0x5>; |
| wakeup-source; |
| brcm,gpio-bank-widths = <18 4>; |
| }; |
| |
| }; |
| |
| memory_controllers { |
| compatible = "simple-bus"; |
| ranges = <0x0 0x0 0xf1100000 0x200000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| memc@0 { |
| compatible = "brcm,brcmstb-memc", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x0 0x80000>; |
| |
| memc-ddr@2000 { |
| compatible = "brcm,brcmstb-memc-ddr"; |
| reg = <0x2000 0x800>; |
| }; |
| |
| ddr-phy@6000 { |
| compatible = "brcm,brcmstb-ddr-phy-v240.1"; |
| reg = <0x6000 0x21c>; |
| }; |
| |
| shimphy@8000 { |
| compatible = "brcm,brcmstb-ddr-shimphy-v1.0"; |
| reg = <0x8000 0xe4>; |
| }; |
| }; |
| |
| memc@1 { |
| compatible = "brcm,brcmstb-memc", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x80000 0x80000>; |
| |
| memc-ddr@2000 { |
| compatible = "brcm,brcmstb-memc-ddr"; |
| reg = <0x2000 0x800>; |
| }; |
| |
| ddr-phy@6000 { |
| compatible = "brcm,brcmstb-ddr-phy-v240.1"; |
| reg = <0x6000 0x21c>; |
| }; |
| |
| shimphy@8000 { |
| compatible = "brcm,brcmstb-ddr-shimphy-v1.0"; |
| reg = <0x8000 0xe4>; |
| }; |
| }; |
| |
| memc@2 { |
| compatible = "brcm,brcmstb-memc", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x100000 0x80000>; |
| |
| memc-ddr@2000 { |
| compatible = "brcm,brcmstb-memc-ddr"; |
| reg = <0x2000 0x800>; |
| }; |
| |
| ddr-phy@6000 { |
| compatible = "brcm,brcmstb-ddr-phy-v240.1"; |
| reg = <0x6000 0x21c>; |
| }; |
| |
| shimphy@8000 { |
| compatible = "brcm,brcmstb-ddr-shimphy-v1.0"; |
| reg = <0x8000 0xe4>; |
| }; |
| }; |
| }; |
| |
| sram@ffe00000 { |
| compatible = "brcm,boot-sram", "mmio-sram"; |
| reg = <0x0 0xffe00000 0x0 0x10000>; |
| }; |
| |
| smpboot { |
| compatible = "brcm,brcmstb-smpboot"; |
| syscon-cpu = <&hif_cpubiuctrl 0x88 0x178>; |
| syscon-cont = <&hif_continuation>; |
| }; |
| |
| reboot { |
| compatible = "brcm,brcmstb-reboot"; |
| syscon = <&sun_top_ctrl 0x304 0x308>; |
| }; |
| }; |
