| /* |
| * Copyright (c) 2009-2013, The Linux Foundation. All rights reserved. |
| * Copyright (c) 2014, Sony Mobile Communications AB. |
| * |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| */ |
| |
| #include <linux/atomic.h> |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/dmaengine.h> |
| #include <linux/dmapool.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/err.h> |
| #include <linux/i2c.h> |
| #include <linux/interrupt.h> |
| #include <linux/io.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/platform_device.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/scatterlist.h> |
| |
| /* QUP Registers */ |
| #define QUP_CONFIG 0x000 |
| #define QUP_STATE 0x004 |
| #define QUP_IO_MODE 0x008 |
| #define QUP_SW_RESET 0x00c |
| #define QUP_OPERATIONAL 0x018 |
| #define QUP_ERROR_FLAGS 0x01c |
| #define QUP_ERROR_FLAGS_EN 0x020 |
| #define QUP_OPERATIONAL_MASK 0x028 |
| #define QUP_HW_VERSION 0x030 |
| #define QUP_MX_OUTPUT_CNT 0x100 |
| #define QUP_OUT_FIFO_BASE 0x110 |
| #define QUP_MX_WRITE_CNT 0x150 |
| #define QUP_MX_INPUT_CNT 0x200 |
| #define QUP_MX_READ_CNT 0x208 |
| #define QUP_IN_FIFO_BASE 0x218 |
| #define QUP_I2C_CLK_CTL 0x400 |
| #define QUP_I2C_STATUS 0x404 |
| #define QUP_I2C_MASTER_GEN 0x408 |
| |
| /* QUP States and reset values */ |
| #define QUP_RESET_STATE 0 |
| #define QUP_RUN_STATE 1 |
| #define QUP_PAUSE_STATE 3 |
| #define QUP_STATE_MASK 3 |
| |
| #define QUP_STATE_VALID BIT(2) |
| #define QUP_I2C_MAST_GEN BIT(4) |
| #define QUP_I2C_FLUSH BIT(6) |
| |
| #define QUP_OPERATIONAL_RESET 0x000ff0 |
| #define QUP_I2C_STATUS_RESET 0xfffffc |
| |
| /* QUP OPERATIONAL FLAGS */ |
| #define QUP_I2C_NACK_FLAG BIT(3) |
| #define QUP_OUT_NOT_EMPTY BIT(4) |
| #define QUP_IN_NOT_EMPTY BIT(5) |
| #define QUP_OUT_FULL BIT(6) |
| #define QUP_OUT_SVC_FLAG BIT(8) |
| #define QUP_IN_SVC_FLAG BIT(9) |
| #define QUP_MX_OUTPUT_DONE BIT(10) |
| #define QUP_MX_INPUT_DONE BIT(11) |
| |
| /* I2C mini core related values */ |
| #define QUP_CLOCK_AUTO_GATE BIT(13) |
| #define I2C_MINI_CORE (2 << 8) |
| #define I2C_N_VAL 15 |
| #define I2C_N_VAL_V2 7 |
| |
| /* Most significant word offset in FIFO port */ |
| #define QUP_MSW_SHIFT (I2C_N_VAL + 1) |
| |
| /* Packing/Unpacking words in FIFOs, and IO modes */ |
| #define QUP_OUTPUT_BLK_MODE (1 << 10) |
| #define QUP_OUTPUT_BAM_MODE (3 << 10) |
| #define QUP_INPUT_BLK_MODE (1 << 12) |
| #define QUP_INPUT_BAM_MODE (3 << 12) |
| #define QUP_BAM_MODE (QUP_OUTPUT_BAM_MODE | QUP_INPUT_BAM_MODE) |
| #define QUP_UNPACK_EN BIT(14) |
| #define QUP_PACK_EN BIT(15) |
| |
| #define QUP_REPACK_EN (QUP_UNPACK_EN | QUP_PACK_EN) |
| #define QUP_V2_TAGS_EN 1 |
| |
| #define QUP_OUTPUT_BLOCK_SIZE(x)(((x) >> 0) & 0x03) |
| #define QUP_OUTPUT_FIFO_SIZE(x) (((x) >> 2) & 0x07) |
| #define QUP_INPUT_BLOCK_SIZE(x) (((x) >> 5) & 0x03) |
| #define QUP_INPUT_FIFO_SIZE(x) (((x) >> 7) & 0x07) |
| |
| /* QUP tags */ |
| #define QUP_TAG_START (1 << 8) |
| #define QUP_TAG_DATA (2 << 8) |
| #define QUP_TAG_STOP (3 << 8) |
| #define QUP_TAG_REC (4 << 8) |
| #define QUP_BAM_INPUT_EOT 0x93 |
| #define QUP_BAM_FLUSH_STOP 0x96 |
| |
| /* QUP v2 tags */ |
| #define QUP_TAG_V2_START 0x81 |
| #define QUP_TAG_V2_DATAWR 0x82 |
| #define QUP_TAG_V2_DATAWR_STOP 0x83 |
| #define QUP_TAG_V2_DATARD 0x85 |
| #define QUP_TAG_V2_DATARD_STOP 0x87 |
| |
| /* Status, Error flags */ |
| #define I2C_STATUS_WR_BUFFER_FULL BIT(0) |
| #define I2C_STATUS_BUS_ACTIVE BIT(8) |
| #define I2C_STATUS_ERROR_MASK 0x38000fc |
| #define QUP_STATUS_ERROR_FLAGS 0x7c |
| |
| #define QUP_READ_LIMIT 256 |
| #define SET_BIT 0x1 |
| #define RESET_BIT 0x0 |
| #define ONE_BYTE 0x1 |
| #define QUP_I2C_MX_CONFIG_DURING_RUN BIT(31) |
| |
| #define MX_TX_RX_LEN SZ_64K |
| #define MX_BLOCKS (MX_TX_RX_LEN / QUP_READ_LIMIT) |
| |
| /* Max timeout in ms for 32k bytes */ |
| #define TOUT_MAX 300 |
| |
| struct qup_i2c_block { |
| int count; |
| int pos; |
| int tx_tag_len; |
| int rx_tag_len; |
| int data_len; |
| u8 tags[6]; |
| }; |
| |
| struct qup_i2c_tag { |
| u8 *start; |
| dma_addr_t addr; |
| }; |
| |
| struct qup_i2c_bam { |
| struct qup_i2c_tag tag; |
| struct dma_chan *dma; |
| struct scatterlist *sg; |
| }; |
| |
| struct qup_i2c_dev { |
| struct device *dev; |
| void __iomem *base; |
| int irq; |
| struct clk *clk; |
| struct clk *pclk; |
| struct i2c_adapter adap; |
| |
| int clk_ctl; |
| int out_fifo_sz; |
| int in_fifo_sz; |
| int out_blk_sz; |
| int in_blk_sz; |
| |
| unsigned long one_byte_t; |
| struct qup_i2c_block blk; |
| |
| struct i2c_msg *msg; |
| /* Current posion in user message buffer */ |
| int pos; |
| /* I2C protocol errors */ |
| u32 bus_err; |
| /* QUP core errors */ |
| u32 qup_err; |
| |
| /* To check if this is the last msg */ |
| bool is_last; |
| |
| /* To configure when bus is in run state */ |
| int config_run; |
| |
| /* dma parameters */ |
| bool is_dma; |
| struct dma_pool *dpool; |
| struct qup_i2c_tag start_tag; |
| struct qup_i2c_bam brx; |
| struct qup_i2c_bam btx; |
| |
| struct completion xfer; |
| }; |
| |
| static irqreturn_t qup_i2c_interrupt(int irq, void *dev) |
| { |
| struct qup_i2c_dev *qup = dev; |
| u32 bus_err; |
| u32 qup_err; |
| u32 opflags; |
| |
| bus_err = readl(qup->base + QUP_I2C_STATUS); |
| qup_err = readl(qup->base + QUP_ERROR_FLAGS); |
| opflags = readl(qup->base + QUP_OPERATIONAL); |
| |
| if (!qup->msg) { |
| /* Clear Error interrupt */ |
| writel(QUP_RESET_STATE, qup->base + QUP_STATE); |
| return IRQ_HANDLED; |
| } |
| |
| bus_err &= I2C_STATUS_ERROR_MASK; |
| qup_err &= QUP_STATUS_ERROR_FLAGS; |
| |
| if (qup_err) { |
| /* Clear Error interrupt */ |
| writel(qup_err, qup->base + QUP_ERROR_FLAGS); |
| goto done; |
| } |
| |
| if (bus_err) { |
| /* Clear Error interrupt */ |
| writel(QUP_RESET_STATE, qup->base + QUP_STATE); |
| goto done; |
| } |
| |
| if (opflags & QUP_IN_SVC_FLAG) |
| writel(QUP_IN_SVC_FLAG, qup->base + QUP_OPERATIONAL); |
| |
| if (opflags & QUP_OUT_SVC_FLAG) |
| writel(QUP_OUT_SVC_FLAG, qup->base + QUP_OPERATIONAL); |
| |
| done: |
| qup->qup_err = qup_err; |
| qup->bus_err = bus_err; |
| complete(&qup->xfer); |
| return IRQ_HANDLED; |
| } |
| |
| static int qup_i2c_poll_state_mask(struct qup_i2c_dev *qup, |
| u32 req_state, u32 req_mask) |
| { |
| int retries = 1; |
| u32 state; |
| |
| /* |
| * State transition takes 3 AHB clocks cycles + 3 I2C master clock |
| * cycles. So retry once after a 1uS delay. |
| */ |
| do { |
| state = readl(qup->base + QUP_STATE); |
| |
| if (state & QUP_STATE_VALID && |
| (state & req_mask) == req_state) |
| return 0; |
| |
| udelay(1); |
| } while (retries--); |
| |
| return -ETIMEDOUT; |
| } |
| |
| static int qup_i2c_poll_state(struct qup_i2c_dev *qup, u32 req_state) |
| { |
| return qup_i2c_poll_state_mask(qup, req_state, QUP_STATE_MASK); |
| } |
| |
| static void qup_i2c_flush(struct qup_i2c_dev *qup) |
| { |
| u32 val = readl(qup->base + QUP_STATE); |
| |
| val |= QUP_I2C_FLUSH; |
| writel(val, qup->base + QUP_STATE); |
| } |
| |
| static int qup_i2c_poll_state_valid(struct qup_i2c_dev *qup) |
| { |
| return qup_i2c_poll_state_mask(qup, 0, 0); |
| } |
| |
| static int qup_i2c_poll_state_i2c_master(struct qup_i2c_dev *qup) |
| { |
| return qup_i2c_poll_state_mask(qup, QUP_I2C_MAST_GEN, QUP_I2C_MAST_GEN); |
| } |
| |
| static int qup_i2c_change_state(struct qup_i2c_dev *qup, u32 state) |
| { |
| if (qup_i2c_poll_state_valid(qup) != 0) |
| return -EIO; |
| |
| writel(state, qup->base + QUP_STATE); |
| |
| if (qup_i2c_poll_state(qup, state) != 0) |
| return -EIO; |
| return 0; |
| } |
| |
| /** |
| * qup_i2c_wait_ready - wait for a give number of bytes in tx/rx path |
| * @qup: The qup_i2c_dev device |
| * @op: The bit/event to wait on |
| * @val: value of the bit to wait on, 0 or 1 |
| * @len: The length the bytes to be transferred |
| */ |
| static int qup_i2c_wait_ready(struct qup_i2c_dev *qup, int op, bool val, |
| int len) |
| { |
| unsigned long timeout; |
| u32 opflags; |
| u32 status; |
| u32 shift = __ffs(op); |
| |
| len *= qup->one_byte_t; |
| /* timeout after a wait of twice the max time */ |
| timeout = jiffies + len * 4; |
| |
| for (;;) { |
| opflags = readl(qup->base + QUP_OPERATIONAL); |
| status = readl(qup->base + QUP_I2C_STATUS); |
| |
| if (((opflags & op) >> shift) == val) { |
| if ((op == QUP_OUT_NOT_EMPTY) && qup->is_last) { |
| if (!(status & I2C_STATUS_BUS_ACTIVE)) |
| return 0; |
| } else { |
| return 0; |
| } |
| } |
| |
| if (time_after(jiffies, timeout)) |
| return -ETIMEDOUT; |
| |
| usleep_range(len, len * 2); |
| } |
| } |
| |
| static void qup_i2c_set_write_mode_v2(struct qup_i2c_dev *qup, |
| struct i2c_msg *msg) |
| { |
| /* Number of entries to shift out, including the tags */ |
| int total = msg->len + qup->blk.tx_tag_len; |
| |
| total |= qup->config_run; |
| |
| if (total < qup->out_fifo_sz) { |
| /* FIFO mode */ |
| writel(QUP_REPACK_EN, qup->base + QUP_IO_MODE); |
| writel(total, qup->base + QUP_MX_WRITE_CNT); |
| } else { |
| /* BLOCK mode (transfer data on chunks) */ |
| writel(QUP_OUTPUT_BLK_MODE | QUP_REPACK_EN, |
| qup->base + QUP_IO_MODE); |
| writel(total, qup->base + QUP_MX_OUTPUT_CNT); |
| } |
| } |
| |
| static void qup_i2c_set_write_mode(struct qup_i2c_dev *qup, struct i2c_msg *msg) |
| { |
| /* Number of entries to shift out, including the start */ |
| int total = msg->len + 1; |
| |
| if (total < qup->out_fifo_sz) { |
| /* FIFO mode */ |
| writel(QUP_REPACK_EN, qup->base + QUP_IO_MODE); |
| writel(total, qup->base + QUP_MX_WRITE_CNT); |
| } else { |
| /* BLOCK mode (transfer data on chunks) */ |
| writel(QUP_OUTPUT_BLK_MODE | QUP_REPACK_EN, |
| qup->base + QUP_IO_MODE); |
| writel(total, qup->base + QUP_MX_OUTPUT_CNT); |
| } |
| } |
| |
| static int check_for_fifo_space(struct qup_i2c_dev *qup) |
| { |
| int ret; |
| |
| ret = qup_i2c_change_state(qup, QUP_PAUSE_STATE); |
| if (ret) |
| goto out; |
| |
| ret = qup_i2c_wait_ready(qup, QUP_OUT_FULL, |
| RESET_BIT, 4 * ONE_BYTE); |
| if (ret) { |
| /* Fifo is full. Drain out the fifo */ |
| ret = qup_i2c_change_state(qup, QUP_RUN_STATE); |
| if (ret) |
| goto out; |
| |
| ret = qup_i2c_wait_ready(qup, QUP_OUT_NOT_EMPTY, |
| RESET_BIT, 256 * ONE_BYTE); |
| if (ret) { |
| dev_err(qup->dev, "timeout for fifo out full"); |
| goto out; |
| } |
| |
| ret = qup_i2c_change_state(qup, QUP_PAUSE_STATE); |
| if (ret) |
| goto out; |
| } |
| |
| out: |
| return ret; |
| } |
| |
| static int qup_i2c_issue_write(struct qup_i2c_dev *qup, struct i2c_msg *msg) |
| { |
| u32 addr = msg->addr << 1; |
| u32 qup_tag; |
| int idx; |
| u32 val; |
| int ret = 0; |
| |
| if (qup->pos == 0) { |
| val = QUP_TAG_START | addr; |
| idx = 1; |
| } else { |
| val = 0; |
| idx = 0; |
| } |
| |
| while (qup->pos < msg->len) { |
| /* Check that there's space in the FIFO for our pair */ |
| ret = check_for_fifo_space(qup); |
| if (ret) |
| return ret; |
| |
| if (qup->pos == msg->len - 1) |
| qup_tag = QUP_TAG_STOP; |
| else |
| qup_tag = QUP_TAG_DATA; |
| |
| if (idx & 1) |
| val |= (qup_tag | msg->buf[qup->pos]) << QUP_MSW_SHIFT; |
| else |
| val = qup_tag | msg->buf[qup->pos]; |
| |
| /* Write out the pair and the last odd value */ |
| if (idx & 1 || qup->pos == msg->len - 1) |
| writel(val, qup->base + QUP_OUT_FIFO_BASE); |
| |
| qup->pos++; |
| idx++; |
| } |
| |
| ret = qup_i2c_change_state(qup, QUP_RUN_STATE); |
| |
| return ret; |
| } |
| |
| static void qup_i2c_set_blk_data(struct qup_i2c_dev *qup, |
| struct i2c_msg *msg) |
| { |
| memset(&qup->blk, 0, sizeof(qup->blk)); |
| |
| qup->blk.data_len = msg->len; |
| qup->blk.count = (msg->len + QUP_READ_LIMIT - 1) / QUP_READ_LIMIT; |
| |
| /* 4 bytes for first block and 2 writes for rest */ |
| qup->blk.tx_tag_len = 4 + (qup->blk.count - 1) * 2; |
| |
| /* There are 2 tag bytes that are read in to fifo for every block */ |
| if (msg->flags & I2C_M_RD) |
| qup->blk.rx_tag_len = qup->blk.count * 2; |
| } |
| |
| static int qup_i2c_send_data(struct qup_i2c_dev *qup, int tlen, u8 *tbuf, |
| int dlen, u8 *dbuf) |
| { |
| u32 val = 0, idx = 0, pos = 0, i = 0, t; |
| int len = tlen + dlen; |
| u8 *buf = tbuf; |
| int ret = 0; |
| |
| while (len > 0) { |
| ret = check_for_fifo_space(qup); |
| if (ret) |
| return ret; |
| |
| t = (len >= 4) ? 4 : len; |
| |
| while (idx < t) { |
| if (!i && (pos >= tlen)) { |
| buf = dbuf; |
| pos = 0; |
| i = 1; |
| } |
| val |= buf[pos++] << (idx++ * 8); |
| } |
| |
| writel(val, qup->base + QUP_OUT_FIFO_BASE); |
| idx = 0; |
| val = 0; |
| len -= 4; |
| } |
| |
| ret = qup_i2c_change_state(qup, QUP_RUN_STATE); |
| |
| return ret; |
| } |
| |
| static int qup_i2c_get_data_len(struct qup_i2c_dev *qup) |
| { |
| int data_len; |
| |
| if (qup->blk.data_len > QUP_READ_LIMIT) |
| data_len = QUP_READ_LIMIT; |
| else |
| data_len = qup->blk.data_len; |
| |
| return data_len; |
| } |
| |
| static int qup_i2c_set_tags(u8 *tags, struct qup_i2c_dev *qup, |
| struct i2c_msg *msg, int is_dma) |
| { |
| u16 addr = i2c_8bit_addr_from_msg(msg); |
| int len = 0; |
| int data_len; |
| |
| int last = (qup->blk.pos == (qup->blk.count - 1)) && (qup->is_last); |
| |
| if (qup->blk.pos == 0) { |
| tags[len++] = QUP_TAG_V2_START; |
| tags[len++] = addr & 0xff; |
| |
| if (msg->flags & I2C_M_TEN) |
| tags[len++] = addr >> 8; |
| } |
| |
| /* Send _STOP commands for the last block */ |
| if (last) { |
| if (msg->flags & I2C_M_RD) |
| tags[len++] = QUP_TAG_V2_DATARD_STOP; |
| else |
| tags[len++] = QUP_TAG_V2_DATAWR_STOP; |
| } else { |
| if (msg->flags & I2C_M_RD) |
| tags[len++] = QUP_TAG_V2_DATARD; |
| else |
| tags[len++] = QUP_TAG_V2_DATAWR; |
| } |
| |
| data_len = qup_i2c_get_data_len(qup); |
| |
| /* 0 implies 256 bytes */ |
| if (data_len == QUP_READ_LIMIT) |
| tags[len++] = 0; |
| else |
| tags[len++] = data_len; |
| |
| if ((msg->flags & I2C_M_RD) && last && is_dma) { |
| tags[len++] = QUP_BAM_INPUT_EOT; |
| tags[len++] = QUP_BAM_FLUSH_STOP; |
| } |
| |
| return len; |
| } |
| |
| static int qup_i2c_issue_xfer_v2(struct qup_i2c_dev *qup, struct i2c_msg *msg) |
| { |
| int data_len = 0, tag_len, index; |
| int ret; |
| |
| tag_len = qup_i2c_set_tags(qup->blk.tags, qup, msg, 0); |
| index = msg->len - qup->blk.data_len; |
| |
| /* only tags are written for read */ |
| if (!(msg->flags & I2C_M_RD)) |
| data_len = qup_i2c_get_data_len(qup); |
| |
| ret = qup_i2c_send_data(qup, tag_len, qup->blk.tags, |
| data_len, &msg->buf[index]); |
| qup->blk.data_len -= data_len; |
| |
| return ret; |
| } |
| |
| static void qup_i2c_bam_cb(void *data) |
| { |
| struct qup_i2c_dev *qup = data; |
| |
| complete(&qup->xfer); |
| } |
| |
| static int qup_sg_set_buf(struct scatterlist *sg, void *buf, |
| struct qup_i2c_tag *tg, unsigned int buflen, |
| struct qup_i2c_dev *qup, int map, int dir) |
| { |
| int ret; |
| |
| sg_set_buf(sg, buf, buflen); |
| ret = dma_map_sg(qup->dev, sg, 1, dir); |
| if (!ret) |
| return -EINVAL; |
| |
| if (!map) |
| sg_dma_address(sg) = tg->addr + ((u8 *)buf - tg->start); |
| |
| return 0; |
| } |
| |
| static void qup_i2c_rel_dma(struct qup_i2c_dev *qup) |
| { |
| if (qup->btx.dma) |
| dma_release_channel(qup->btx.dma); |
| if (qup->brx.dma) |
| dma_release_channel(qup->brx.dma); |
| qup->btx.dma = NULL; |
| qup->brx.dma = NULL; |
| } |
| |
| static int qup_i2c_req_dma(struct qup_i2c_dev *qup) |
| { |
| int err; |
| |
| if (!qup->btx.dma) { |
| qup->btx.dma = dma_request_slave_channel_reason(qup->dev, "tx"); |
| if (IS_ERR(qup->btx.dma)) { |
| err = PTR_ERR(qup->btx.dma); |
| qup->btx.dma = NULL; |
| dev_err(qup->dev, "\n tx channel not available"); |
| return err; |
| } |
| } |
| |
| if (!qup->brx.dma) { |
| qup->brx.dma = dma_request_slave_channel_reason(qup->dev, "rx"); |
| if (IS_ERR(qup->brx.dma)) { |
| dev_err(qup->dev, "\n rx channel not available"); |
| err = PTR_ERR(qup->brx.dma); |
| qup->brx.dma = NULL; |
| qup_i2c_rel_dma(qup); |
| return err; |
| } |
| } |
| return 0; |
| } |
| |
| static int qup_i2c_bam_do_xfer(struct qup_i2c_dev *qup, struct i2c_msg *msg, |
| int num) |
| { |
| struct dma_async_tx_descriptor *txd, *rxd = NULL; |
| int ret = 0, idx = 0, limit = QUP_READ_LIMIT; |
| dma_cookie_t cookie_rx, cookie_tx; |
| u32 rx_nents = 0, tx_nents = 0, len, blocks, rem; |
| u32 i, tlen, tx_len, tx_buf = 0, rx_buf = 0, off = 0; |
| u8 *tags; |
| |
| while (idx < num) { |
| blocks = (msg->len + limit) / limit; |
| rem = msg->len % limit; |
| tx_len = 0, len = 0, i = 0; |
| |
| qup->is_last = (idx == (num - 1)); |
| |
| qup_i2c_set_blk_data(qup, msg); |
| |
| if (msg->flags & I2C_M_RD) { |
| rx_nents += (blocks * 2) + 1; |
| tx_nents += 1; |
| |
| while (qup->blk.pos < blocks) { |
| /* length set to '0' implies 256 bytes */ |
| tlen = (i == (blocks - 1)) ? rem : 0; |
| tags = &qup->start_tag.start[off + len]; |
| len += qup_i2c_set_tags(tags, qup, msg, 1); |
| |
| /* scratch buf to read the start and len tags */ |
| ret = qup_sg_set_buf(&qup->brx.sg[rx_buf++], |
| &qup->brx.tag.start[0], |
| &qup->brx.tag, |
| 2, qup, 0, 0); |
| |
| if (ret) |
| return ret; |
| |
| ret = qup_sg_set_buf(&qup->brx.sg[rx_buf++], |
| &msg->buf[limit * i], |
| NULL, tlen, qup, |
| 1, DMA_FROM_DEVICE); |
| if (ret) |
| return ret; |
| |
| i++; |
| qup->blk.pos = i; |
| } |
| ret = qup_sg_set_buf(&qup->btx.sg[tx_buf++], |
| &qup->start_tag.start[off], |
| &qup->start_tag, len, qup, 0, 0); |
| if (ret) |
| return ret; |
| |
| off += len; |
| /* scratch buf to read the BAM EOT and FLUSH tags */ |
| ret = qup_sg_set_buf(&qup->brx.sg[rx_buf++], |
| &qup->brx.tag.start[0], |
| &qup->brx.tag, 2, |
| qup, 0, 0); |
| if (ret) |
| return ret; |
| } else { |
| tx_nents += (blocks * 2); |
| |
| while (qup->blk.pos < blocks) { |
| tlen = (i == (blocks - 1)) ? rem : 0; |
| tags = &qup->start_tag.start[off + tx_len]; |
| len = qup_i2c_set_tags(tags, qup, msg, 1); |
| |
| ret = qup_sg_set_buf(&qup->btx.sg[tx_buf++], |
| tags, |
| &qup->start_tag, len, |
| qup, 0, 0); |
| if (ret) |
| return ret; |
| |
| tx_len += len; |
| ret = qup_sg_set_buf(&qup->btx.sg[tx_buf++], |
| &msg->buf[limit * i], |
| NULL, tlen, qup, 1, |
| DMA_TO_DEVICE); |
| if (ret) |
| return ret; |
| i++; |
| qup->blk.pos = i; |
| } |
| off += tx_len; |
| |
| if (idx == (num - 1)) { |
| len = 1; |
| if (rx_nents) { |
| qup->btx.tag.start[0] = |
| QUP_BAM_INPUT_EOT; |
| len++; |
| } |
| qup->btx.tag.start[len - 1] = |
| QUP_BAM_FLUSH_STOP; |
| ret = qup_sg_set_buf(&qup->btx.sg[tx_buf++], |
| &qup->btx.tag.start[0], |
| &qup->btx.tag, len, |
| qup, 0, 0); |
| if (ret) |
| return ret; |
| tx_nents += 1; |
| } |
| } |
| idx++; |
| msg++; |
| } |
| |
| txd = dmaengine_prep_slave_sg(qup->btx.dma, qup->btx.sg, tx_nents, |
| DMA_MEM_TO_DEV, |
| DMA_PREP_INTERRUPT | DMA_PREP_FENCE); |
| if (!txd) { |
| dev_err(qup->dev, "failed to get tx desc\n"); |
| ret = -EINVAL; |
| goto desc_err; |
| } |
| |
| if (!rx_nents) { |
| txd->callback = qup_i2c_bam_cb; |
| txd->callback_param = qup; |
| } |
| |
| cookie_tx = dmaengine_submit(txd); |
| if (dma_submit_error(cookie_tx)) { |
| ret = -EINVAL; |
| goto desc_err; |
| } |
| |
| dma_async_issue_pending(qup->btx.dma); |
| |
| if (rx_nents) { |
| rxd = dmaengine_prep_slave_sg(qup->brx.dma, qup->brx.sg, |
| rx_nents, DMA_DEV_TO_MEM, |
| DMA_PREP_INTERRUPT); |
| if (!rxd) { |
| dev_err(qup->dev, "failed to get rx desc\n"); |
| ret = -EINVAL; |
| |
| /* abort TX descriptors */ |
| dmaengine_terminate_all(qup->btx.dma); |
| goto desc_err; |
| } |
| |
| rxd->callback = qup_i2c_bam_cb; |
| rxd->callback_param = qup; |
| cookie_rx = dmaengine_submit(rxd); |
| if (dma_submit_error(cookie_rx)) { |
| ret = -EINVAL; |
| goto desc_err; |
| } |
| |
| dma_async_issue_pending(qup->brx.dma); |
| } |
| |
| if (!wait_for_completion_timeout(&qup->xfer, TOUT_MAX * HZ)) { |
| dev_err(qup->dev, "normal trans timed out\n"); |
| ret = -ETIMEDOUT; |
| } |
| |
| if (ret || qup->bus_err || qup->qup_err) { |
| if (qup->bus_err & QUP_I2C_NACK_FLAG) { |
| msg--; |
| dev_err(qup->dev, "NACK from %x\n", msg->addr); |
| ret = -EIO; |
| |
| if (qup_i2c_change_state(qup, QUP_RUN_STATE)) { |
| dev_err(qup->dev, "change to run state timed out"); |
| return ret; |
| } |
| |
| if (rx_nents) |
| writel(QUP_BAM_INPUT_EOT, |
| qup->base + QUP_OUT_FIFO_BASE); |
| |
| writel(QUP_BAM_FLUSH_STOP, |
| qup->base + QUP_OUT_FIFO_BASE); |
| |
| qup_i2c_flush(qup); |
| |
| /* wait for remaining interrupts to occur */ |
| if (!wait_for_completion_timeout(&qup->xfer, HZ)) |
| dev_err(qup->dev, "flush timed out\n"); |
| |
| qup_i2c_rel_dma(qup); |
| } |
| } |
| |
| dma_unmap_sg(qup->dev, qup->btx.sg, tx_nents, DMA_TO_DEVICE); |
| |
| if (rx_nents) |
| dma_unmap_sg(qup->dev, qup->brx.sg, rx_nents, |
| DMA_FROM_DEVICE); |
| desc_err: |
| return ret; |
| } |
| |
| static int qup_i2c_bam_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, |
| int num) |
| { |
| struct qup_i2c_dev *qup = i2c_get_adapdata(adap); |
| int ret = 0; |
| |
| enable_irq(qup->irq); |
| ret = qup_i2c_req_dma(qup); |
| |
| if (ret) |
| goto out; |
| |
| qup->bus_err = 0; |
| qup->qup_err = 0; |
| |
| writel(0, qup->base + QUP_MX_INPUT_CNT); |
| writel(0, qup->base + QUP_MX_OUTPUT_CNT); |
| |
| /* set BAM mode */ |
| writel(QUP_REPACK_EN | QUP_BAM_MODE, qup->base + QUP_IO_MODE); |
| |
| /* mask fifo irqs */ |
| writel((0x3 << 8), qup->base + QUP_OPERATIONAL_MASK); |
| |
| /* set RUN STATE */ |
| ret = qup_i2c_change_state(qup, QUP_RUN_STATE); |
| if (ret) |
| goto out; |
| |
| writel(qup->clk_ctl, qup->base + QUP_I2C_CLK_CTL); |
| |
| qup->msg = msg; |
| ret = qup_i2c_bam_do_xfer(qup, qup->msg, num); |
| out: |
| disable_irq(qup->irq); |
| |
| qup->msg = NULL; |
| return ret; |
| } |
| |
| static int qup_i2c_wait_for_complete(struct qup_i2c_dev *qup, |
| struct i2c_msg *msg) |
| { |
| unsigned long left; |
| int ret = 0; |
| |
| left = wait_for_completion_timeout(&qup->xfer, HZ); |
| if (!left) { |
| writel(1, qup->base + QUP_SW_RESET); |
| ret = -ETIMEDOUT; |
| } |
| |
| if (qup->bus_err || qup->qup_err) { |
| if (qup->bus_err & QUP_I2C_NACK_FLAG) { |
| dev_err(qup->dev, "NACK from %x\n", msg->addr); |
| ret = -EIO; |
| } |
| } |
| |
| return ret; |
| } |
| |
| static int qup_i2c_write_one_v2(struct qup_i2c_dev *qup, struct i2c_msg *msg) |
| { |
| int ret = 0; |
| |
| qup->msg = msg; |
| qup->pos = 0; |
| enable_irq(qup->irq); |
| qup_i2c_set_blk_data(qup, msg); |
| qup_i2c_set_write_mode_v2(qup, msg); |
| |
| ret = qup_i2c_change_state(qup, QUP_RUN_STATE); |
| if (ret) |
| goto err; |
| |
| writel(qup->clk_ctl, qup->base + QUP_I2C_CLK_CTL); |
| |
| do { |
| ret = qup_i2c_issue_xfer_v2(qup, msg); |
| if (ret) |
| goto err; |
| |
| ret = qup_i2c_wait_for_complete(qup, msg); |
| if (ret) |
| goto err; |
| |
| qup->blk.pos++; |
| } while (qup->blk.pos < qup->blk.count); |
| |
| ret = qup_i2c_wait_ready(qup, QUP_OUT_NOT_EMPTY, RESET_BIT, ONE_BYTE); |
| |
| err: |
| disable_irq(qup->irq); |
| qup->msg = NULL; |
| |
| return ret; |
| } |
| |
| static int qup_i2c_write_one(struct qup_i2c_dev *qup, struct i2c_msg *msg) |
| { |
| int ret; |
| |
| qup->msg = msg; |
| qup->pos = 0; |
| |
| enable_irq(qup->irq); |
| |
| qup_i2c_set_write_mode(qup, msg); |
| |
| ret = qup_i2c_change_state(qup, QUP_RUN_STATE); |
| if (ret) |
| goto err; |
| |
| writel(qup->clk_ctl, qup->base + QUP_I2C_CLK_CTL); |
| |
| do { |
| ret = qup_i2c_change_state(qup, QUP_PAUSE_STATE); |
| if (ret) |
| goto err; |
| |
| ret = qup_i2c_issue_write(qup, msg); |
| if (ret) |
| goto err; |
| |
| ret = qup_i2c_change_state(qup, QUP_RUN_STATE); |
| if (ret) |
| goto err; |
| |
| ret = qup_i2c_wait_for_complete(qup, msg); |
| if (ret) |
| goto err; |
| } while (qup->pos < msg->len); |
| |
| /* Wait for the outstanding data in the fifo to drain */ |
| ret = qup_i2c_wait_ready(qup, QUP_OUT_NOT_EMPTY, RESET_BIT, ONE_BYTE); |
| err: |
| disable_irq(qup->irq); |
| qup->msg = NULL; |
| |
| return ret; |
| } |
| |
| static void qup_i2c_set_read_mode(struct qup_i2c_dev *qup, int len) |
| { |
| if (len < qup->in_fifo_sz) { |
| /* FIFO mode */ |
| writel(QUP_REPACK_EN, qup->base + QUP_IO_MODE); |
| writel(len, qup->base + QUP_MX_READ_CNT); |
| } else { |
| /* BLOCK mode (transfer data on chunks) */ |
| writel(QUP_INPUT_BLK_MODE | QUP_REPACK_EN, |
| qup->base + QUP_IO_MODE); |
| writel(len, qup->base + QUP_MX_INPUT_CNT); |
| } |
| } |
| |
| static void qup_i2c_set_read_mode_v2(struct qup_i2c_dev *qup, int len) |
| { |
| int tx_len = qup->blk.tx_tag_len; |
| |
| len += qup->blk.rx_tag_len; |
| len |= qup->config_run; |
| tx_len |= qup->config_run; |
| |
| if (len < qup->in_fifo_sz) { |
| /* FIFO mode */ |
| writel(QUP_REPACK_EN, qup->base + QUP_IO_MODE); |
| writel(tx_len, qup->base + QUP_MX_WRITE_CNT); |
| writel(len, qup->base + QUP_MX_READ_CNT); |
| } else { |
| /* BLOCK mode (transfer data on chunks) */ |
| writel(QUP_INPUT_BLK_MODE | QUP_REPACK_EN, |
| qup->base + QUP_IO_MODE); |
| writel(tx_len, qup->base + QUP_MX_OUTPUT_CNT); |
| writel(len, qup->base + QUP_MX_INPUT_CNT); |
| } |
| } |
| |
| static void qup_i2c_issue_read(struct qup_i2c_dev *qup, struct i2c_msg *msg) |
| { |
| u32 addr, len, val; |
| |
| addr = (msg->addr << 1) | 1; |
| |
| /* 0 is used to specify a length 256 (QUP_READ_LIMIT) */ |
| len = (msg->len == QUP_READ_LIMIT) ? 0 : msg->len; |
| |
| val = ((QUP_TAG_REC | len) << QUP_MSW_SHIFT) | QUP_TAG_START | addr; |
| writel(val, qup->base + QUP_OUT_FIFO_BASE); |
| } |
| |
| |
| static int qup_i2c_read_fifo(struct qup_i2c_dev *qup, struct i2c_msg *msg) |
| { |
| u32 val = 0; |
| int idx; |
| int ret = 0; |
| |
| for (idx = 0; qup->pos < msg->len; idx++) { |
| if ((idx & 1) == 0) { |
| /* Check that FIFO have data */ |
| ret = qup_i2c_wait_ready(qup, QUP_IN_NOT_EMPTY, |
| SET_BIT, 4 * ONE_BYTE); |
| if (ret) |
| return ret; |
| |
| /* Reading 2 words at time */ |
| val = readl(qup->base + QUP_IN_FIFO_BASE); |
| |
| msg->buf[qup->pos++] = val & 0xFF; |
| } else { |
| msg->buf[qup->pos++] = val >> QUP_MSW_SHIFT; |
| } |
| } |
| |
| return ret; |
| } |
| |
| static int qup_i2c_read_fifo_v2(struct qup_i2c_dev *qup, |
| struct i2c_msg *msg) |
| { |
| u32 val; |
| int idx, pos = 0, ret = 0, total; |
| |
| total = qup_i2c_get_data_len(qup); |
| |
| /* 2 extra bytes for read tags */ |
| while (pos < (total + 2)) { |
| /* Check that FIFO have data */ |
| ret = qup_i2c_wait_ready(qup, QUP_IN_NOT_EMPTY, |
| SET_BIT, 4 * ONE_BYTE); |
| if (ret) { |
| dev_err(qup->dev, "timeout for fifo not empty"); |
| return ret; |
| } |
| val = readl(qup->base + QUP_IN_FIFO_BASE); |
| |
| for (idx = 0; idx < 4; idx++, val >>= 8, pos++) { |
| /* first 2 bytes are tag bytes */ |
| if (pos < 2) |
| continue; |
| |
| if (pos >= (total + 2)) |
| goto out; |
| |
| msg->buf[qup->pos++] = val & 0xff; |
| } |
| } |
| |
| out: |
| qup->blk.data_len -= total; |
| |
| return ret; |
| } |
| |
| static int qup_i2c_read_one_v2(struct qup_i2c_dev *qup, struct i2c_msg *msg) |
| { |
| int ret = 0; |
| |
| qup->msg = msg; |
| qup->pos = 0; |
| enable_irq(qup->irq); |
| qup_i2c_set_blk_data(qup, msg); |
| qup_i2c_set_read_mode_v2(qup, msg->len); |
| |
| ret = qup_i2c_change_state(qup, QUP_RUN_STATE); |
| if (ret) |
| goto err; |
| |
| writel(qup->clk_ctl, qup->base + QUP_I2C_CLK_CTL); |
| |
| do { |
| ret = qup_i2c_issue_xfer_v2(qup, msg); |
| if (ret) |
| goto err; |
| |
| ret = qup_i2c_wait_for_complete(qup, msg); |
| if (ret) |
| goto err; |
| |
| ret = qup_i2c_read_fifo_v2(qup, msg); |
| if (ret) |
| goto err; |
| |
| qup->blk.pos++; |
| } while (qup->blk.pos < qup->blk.count); |
| |
| err: |
| disable_irq(qup->irq); |
| qup->msg = NULL; |
| |
| return ret; |
| } |
| |
| static int qup_i2c_read_one(struct qup_i2c_dev *qup, struct i2c_msg *msg) |
| { |
| int ret; |
| |
| qup->msg = msg; |
| qup->pos = 0; |
| |
| enable_irq(qup->irq); |
| qup_i2c_set_read_mode(qup, msg->len); |
| |
| ret = qup_i2c_change_state(qup, QUP_RUN_STATE); |
| if (ret) |
| goto err; |
| |
| writel(qup->clk_ctl, qup->base + QUP_I2C_CLK_CTL); |
| |
| ret = qup_i2c_change_state(qup, QUP_PAUSE_STATE); |
| if (ret) |
| goto err; |
| |
| qup_i2c_issue_read(qup, msg); |
| |
| ret = qup_i2c_change_state(qup, QUP_RUN_STATE); |
| if (ret) |
| goto err; |
| |
| do { |
| ret = qup_i2c_wait_for_complete(qup, msg); |
| if (ret) |
| goto err; |
| |
| ret = qup_i2c_read_fifo(qup, msg); |
| if (ret) |
| goto err; |
| } while (qup->pos < msg->len); |
| |
| err: |
| disable_irq(qup->irq); |
| qup->msg = NULL; |
| |
| return ret; |
| } |
| |
| static int qup_i2c_xfer(struct i2c_adapter *adap, |
| struct i2c_msg msgs[], |
| int num) |
| { |
| struct qup_i2c_dev *qup = i2c_get_adapdata(adap); |
| int ret, idx; |
| |
| ret = pm_runtime_get_sync(qup->dev); |
| if (ret < 0) |
| goto out; |
| |
| writel(1, qup->base + QUP_SW_RESET); |
| ret = qup_i2c_poll_state(qup, QUP_RESET_STATE); |
| if (ret) |
| goto out; |
| |
| /* Configure QUP as I2C mini core */ |
| writel(I2C_MINI_CORE | I2C_N_VAL, qup->base + QUP_CONFIG); |
| |
| for (idx = 0; idx < num; idx++) { |
| if (msgs[idx].len == 0) { |
| ret = -EINVAL; |
| goto out; |
| } |
| |
| if (qup_i2c_poll_state_i2c_master(qup)) { |
| ret = -EIO; |
| goto out; |
| } |
| |
| if (msgs[idx].flags & I2C_M_RD) |
| ret = qup_i2c_read_one(qup, &msgs[idx]); |
| else |
| ret = qup_i2c_write_one(qup, &msgs[idx]); |
| |
| if (ret) |
| break; |
| |
| ret = qup_i2c_change_state(qup, QUP_RESET_STATE); |
| if (ret) |
| break; |
| } |
| |
| if (ret == 0) |
| ret = num; |
| out: |
| |
| pm_runtime_mark_last_busy(qup->dev); |
| pm_runtime_put_autosuspend(qup->dev); |
| |
| return ret; |
| } |
| |
| static int qup_i2c_xfer_v2(struct i2c_adapter *adap, |
| struct i2c_msg msgs[], |
| int num) |
| { |
| struct qup_i2c_dev *qup = i2c_get_adapdata(adap); |
| int ret, len, idx = 0, use_dma = 0; |
| |
| ret = pm_runtime_get_sync(qup->dev); |
| if (ret < 0) |
| goto out; |
| |
| writel(1, qup->base + QUP_SW_RESET); |
| ret = qup_i2c_poll_state(qup, QUP_RESET_STATE); |
| if (ret) |
| goto out; |
| |
| /* Configure QUP as I2C mini core */ |
| writel(I2C_MINI_CORE | I2C_N_VAL_V2, qup->base + QUP_CONFIG); |
| writel(QUP_V2_TAGS_EN, qup->base + QUP_I2C_MASTER_GEN); |
| |
| if ((qup->is_dma)) { |
| /* All i2c_msgs should be transferred using either dma or cpu */ |
| for (idx = 0; idx < num; idx++) { |
| if (msgs[idx].len == 0) { |
| ret = -EINVAL; |
| goto out; |
| } |
| |
| len = (msgs[idx].len > qup->out_fifo_sz) || |
| (msgs[idx].len > qup->in_fifo_sz); |
| |
| if ((!is_vmalloc_addr(msgs[idx].buf)) && len) { |
| use_dma = 1; |
| } else { |
| use_dma = 0; |
| break; |
| } |
| } |
| } |
| |
| do { |
| if (msgs[idx].len == 0) { |
| ret = -EINVAL; |
| goto out; |
| } |
| |
| if (qup_i2c_poll_state_i2c_master(qup)) { |
| ret = -EIO; |
| goto out; |
| } |
| |
| qup->is_last = (idx == (num - 1)); |
| if (idx) |
| qup->config_run = QUP_I2C_MX_CONFIG_DURING_RUN; |
| else |
| qup->config_run = 0; |
| |
| reinit_completion(&qup->xfer); |
| |
| if (use_dma) { |
| ret = qup_i2c_bam_xfer(adap, &msgs[idx], num); |
| } else { |
| if (msgs[idx].flags & I2C_M_RD) |
| ret = qup_i2c_read_one_v2(qup, &msgs[idx]); |
| else |
| ret = qup_i2c_write_one_v2(qup, &msgs[idx]); |
| } |
| } while ((idx++ < (num - 1)) && !use_dma && !ret); |
| |
| if (!ret) |
| ret = qup_i2c_change_state(qup, QUP_RESET_STATE); |
| |
| if (ret == 0) |
| ret = num; |
| out: |
| pm_runtime_mark_last_busy(qup->dev); |
| pm_runtime_put_autosuspend(qup->dev); |
| |
| return ret; |
| } |
| |
| static u32 qup_i2c_func(struct i2c_adapter *adap) |
| { |
| return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK); |
| } |
| |
| static const struct i2c_algorithm qup_i2c_algo = { |
| .master_xfer = qup_i2c_xfer, |
| .functionality = qup_i2c_func, |
| }; |
| |
| static const struct i2c_algorithm qup_i2c_algo_v2 = { |
| .master_xfer = qup_i2c_xfer_v2, |
| .functionality = qup_i2c_func, |
| }; |
| |
| /* |
| * The QUP block will issue a NACK and STOP on the bus when reaching |
| * the end of the read, the length of the read is specified as one byte |
| * which limits the possible read to 256 (QUP_READ_LIMIT) bytes. |
| */ |
| static struct i2c_adapter_quirks qup_i2c_quirks = { |
| .max_read_len = QUP_READ_LIMIT, |
| }; |
| |
| static void qup_i2c_enable_clocks(struct qup_i2c_dev *qup) |
| { |
| clk_prepare_enable(qup->clk); |
| clk_prepare_enable(qup->pclk); |
| } |
| |
| static void qup_i2c_disable_clocks(struct qup_i2c_dev *qup) |
| { |
| u32 config; |
| |
| qup_i2c_change_state(qup, QUP_RESET_STATE); |
| clk_disable_unprepare(qup->clk); |
| config = readl(qup->base + QUP_CONFIG); |
| config |= QUP_CLOCK_AUTO_GATE; |
| writel(config, qup->base + QUP_CONFIG); |
| clk_disable_unprepare(qup->pclk); |
| } |
| |
| static int qup_i2c_probe(struct platform_device *pdev) |
| { |
| static const int blk_sizes[] = {4, 16, 32}; |
| struct device_node *node = pdev->dev.of_node; |
| struct qup_i2c_dev *qup; |
| unsigned long one_bit_t; |
| struct resource *res; |
| u32 io_mode, hw_ver, size; |
| int ret, fs_div, hs_div; |
| int src_clk_freq; |
| u32 clk_freq = 100000; |
| int blocks; |
| |
| qup = devm_kzalloc(&pdev->dev, sizeof(*qup), GFP_KERNEL); |
| if (!qup) |
| return -ENOMEM; |
| |
| qup->dev = &pdev->dev; |
| init_completion(&qup->xfer); |
| platform_set_drvdata(pdev, qup); |
| |
| of_property_read_u32(node, "clock-frequency", &clk_freq); |
| |
| if (of_device_is_compatible(pdev->dev.of_node, "qcom,i2c-qup-v1.1.1")) { |
| qup->adap.algo = &qup_i2c_algo; |
| qup->adap.quirks = &qup_i2c_quirks; |
| } else { |
| qup->adap.algo = &qup_i2c_algo_v2; |
| ret = qup_i2c_req_dma(qup); |
| |
| if (ret == -EPROBE_DEFER) |
| goto fail_dma; |
| else if (ret != 0) |
| goto nodma; |
| |
| blocks = (MX_BLOCKS << 1) + 1; |
| qup->btx.sg = devm_kzalloc(&pdev->dev, |
| sizeof(*qup->btx.sg) * blocks, |
| GFP_KERNEL); |
| if (!qup->btx.sg) { |
| ret = -ENOMEM; |
| goto fail_dma; |
| } |
| sg_init_table(qup->btx.sg, blocks); |
| |
| qup->brx.sg = devm_kzalloc(&pdev->dev, |
| sizeof(*qup->brx.sg) * blocks, |
| GFP_KERNEL); |
| if (!qup->brx.sg) { |
| ret = -ENOMEM; |
| goto fail_dma; |
| } |
| sg_init_table(qup->brx.sg, blocks); |
| |
| /* 2 tag bytes for each block + 5 for start, stop tags */ |
| size = blocks * 2 + 5; |
| qup->dpool = dma_pool_create("qup_i2c-dma-pool", &pdev->dev, |
| size, 4, 0); |
| |
| qup->start_tag.start = dma_pool_alloc(qup->dpool, GFP_KERNEL, |
| &qup->start_tag.addr); |
| if (!qup->start_tag.start) { |
| ret = -ENOMEM; |
| goto fail_dma; |
| } |
| |
| qup->brx.tag.start = dma_pool_alloc(qup->dpool, |
| GFP_KERNEL, |
| &qup->brx.tag.addr); |
| if (!qup->brx.tag.start) { |
| ret = -ENOMEM; |
| goto fail_dma; |
| } |
| |
| qup->btx.tag.start = dma_pool_alloc(qup->dpool, |
| GFP_KERNEL, |
| &qup->btx.tag.addr); |
| if (!qup->btx.tag.start) { |
| ret = -ENOMEM; |
| goto fail_dma; |
| } |
| qup->is_dma = true; |
| } |
| |
| nodma: |
| /* We support frequencies up to FAST Mode (400KHz) */ |
| if (!clk_freq || clk_freq > 400000) { |
| dev_err(qup->dev, "clock frequency not supported %d\n", |
| clk_freq); |
| return -EINVAL; |
| } |
| |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| qup->base = devm_ioremap_resource(qup->dev, res); |
| if (IS_ERR(qup->base)) |
| return PTR_ERR(qup->base); |
| |
| qup->irq = platform_get_irq(pdev, 0); |
| if (qup->irq < 0) { |
| dev_err(qup->dev, "No IRQ defined\n"); |
| return qup->irq; |
| } |
| |
| qup->clk = devm_clk_get(qup->dev, "core"); |
| if (IS_ERR(qup->clk)) { |
| dev_err(qup->dev, "Could not get core clock\n"); |
| return PTR_ERR(qup->clk); |
| } |
| |
| qup->pclk = devm_clk_get(qup->dev, "iface"); |
| if (IS_ERR(qup->pclk)) { |
| dev_err(qup->dev, "Could not get iface clock\n"); |
| return PTR_ERR(qup->pclk); |
| } |
| |
| qup_i2c_enable_clocks(qup); |
| |
| /* |
| * Bootloaders might leave a pending interrupt on certain QUP's, |
| * so we reset the core before registering for interrupts. |
| */ |
| writel(1, qup->base + QUP_SW_RESET); |
| ret = qup_i2c_poll_state_valid(qup); |
| if (ret) |
| goto fail; |
| |
| ret = devm_request_irq(qup->dev, qup->irq, qup_i2c_interrupt, |
| IRQF_TRIGGER_HIGH, "i2c_qup", qup); |
| if (ret) { |
| dev_err(qup->dev, "Request %d IRQ failed\n", qup->irq); |
| goto fail; |
| } |
| disable_irq(qup->irq); |
| |
| hw_ver = readl(qup->base + QUP_HW_VERSION); |
| dev_dbg(qup->dev, "Revision %x\n", hw_ver); |
| |
| io_mode = readl(qup->base + QUP_IO_MODE); |
| |
| /* |
| * The block/fifo size w.r.t. 'actual data' is 1/2 due to 'tag' |
| * associated with each byte written/received |
| */ |
| size = QUP_OUTPUT_BLOCK_SIZE(io_mode); |
| if (size >= ARRAY_SIZE(blk_sizes)) { |
| ret = -EIO; |
| goto fail; |
| } |
| qup->out_blk_sz = blk_sizes[size] / 2; |
| |
| size = QUP_INPUT_BLOCK_SIZE(io_mode); |
| if (size >= ARRAY_SIZE(blk_sizes)) { |
| ret = -EIO; |
| goto fail; |
| } |
| qup->in_blk_sz = blk_sizes[size] / 2; |
| |
| size = QUP_OUTPUT_FIFO_SIZE(io_mode); |
| qup->out_fifo_sz = qup->out_blk_sz * (2 << size); |
| |
| size = QUP_INPUT_FIFO_SIZE(io_mode); |
| qup->in_fifo_sz = qup->in_blk_sz * (2 << size); |
| |
| src_clk_freq = clk_get_rate(qup->clk); |
| fs_div = ((src_clk_freq / clk_freq) / 2) - 3; |
| hs_div = 3; |
| qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff); |
| |
| /* |
| * Time it takes for a byte to be clocked out on the bus. |
| * Each byte takes 9 clock cycles (8 bits + 1 ack). |
| */ |
| one_bit_t = (USEC_PER_SEC / clk_freq) + 1; |
| qup->one_byte_t = one_bit_t * 9; |
| |
| dev_dbg(qup->dev, "IN:block:%d, fifo:%d, OUT:block:%d, fifo:%d\n", |
| qup->in_blk_sz, qup->in_fifo_sz, |
| qup->out_blk_sz, qup->out_fifo_sz); |
| |
| i2c_set_adapdata(&qup->adap, qup); |
| qup->adap.dev.parent = qup->dev; |
| qup->adap.dev.of_node = pdev->dev.of_node; |
| qup->is_last = true; |
| |
| strlcpy(qup->adap.name, "QUP I2C adapter", sizeof(qup->adap.name)); |
| |
| pm_runtime_set_autosuspend_delay(qup->dev, MSEC_PER_SEC); |
| pm_runtime_use_autosuspend(qup->dev); |
| pm_runtime_set_active(qup->dev); |
| pm_runtime_enable(qup->dev); |
| |
| ret = i2c_add_adapter(&qup->adap); |
| if (ret) |
| goto fail_runtime; |
| |
| return 0; |
| |
| fail_runtime: |
| pm_runtime_disable(qup->dev); |
| pm_runtime_set_suspended(qup->dev); |
| fail: |
| qup_i2c_disable_clocks(qup); |
| fail_dma: |
| if (qup->btx.dma) |
| dma_release_channel(qup->btx.dma); |
| if (qup->brx.dma) |
| dma_release_channel(qup->brx.dma); |
| return ret; |
| } |
| |
| static int qup_i2c_remove(struct platform_device *pdev) |
| { |
| struct qup_i2c_dev *qup = platform_get_drvdata(pdev); |
| |
| if (qup->is_dma) { |
| dma_pool_free(qup->dpool, qup->start_tag.start, |
| qup->start_tag.addr); |
| dma_pool_free(qup->dpool, qup->brx.tag.start, |
| qup->brx.tag.addr); |
| dma_pool_free(qup->dpool, qup->btx.tag.start, |
| qup->btx.tag.addr); |
| dma_pool_destroy(qup->dpool); |
| dma_release_channel(qup->btx.dma); |
| dma_release_channel(qup->brx.dma); |
| } |
| |
| disable_irq(qup->irq); |
| qup_i2c_disable_clocks(qup); |
| i2c_del_adapter(&qup->adap); |
| pm_runtime_disable(qup->dev); |
| pm_runtime_set_suspended(qup->dev); |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM |
| static int qup_i2c_pm_suspend_runtime(struct device *device) |
| { |
| struct qup_i2c_dev *qup = dev_get_drvdata(device); |
| |
| dev_dbg(device, "pm_runtime: suspending...\n"); |
| qup_i2c_disable_clocks(qup); |
| return 0; |
| } |
| |
| static int qup_i2c_pm_resume_runtime(struct device *device) |
| { |
| struct qup_i2c_dev *qup = dev_get_drvdata(device); |
| |
| dev_dbg(device, "pm_runtime: resuming...\n"); |
| qup_i2c_enable_clocks(qup); |
| return 0; |
| } |
| #endif |
| |
| #ifdef CONFIG_PM_SLEEP |
| static int qup_i2c_suspend(struct device *device) |
| { |
| qup_i2c_pm_suspend_runtime(device); |
| return 0; |
| } |
| |
| static int qup_i2c_resume(struct device *device) |
| { |
| qup_i2c_pm_resume_runtime(device); |
| pm_runtime_mark_last_busy(device); |
| pm_request_autosuspend(device); |
| return 0; |
| } |
| #endif |
| |
| static const struct dev_pm_ops qup_i2c_qup_pm_ops = { |
| SET_SYSTEM_SLEEP_PM_OPS( |
| qup_i2c_suspend, |
| qup_i2c_resume) |
| SET_RUNTIME_PM_OPS( |
| qup_i2c_pm_suspend_runtime, |
| qup_i2c_pm_resume_runtime, |
| NULL) |
| }; |
| |
| static const struct of_device_id qup_i2c_dt_match[] = { |
| { .compatible = "qcom,i2c-qup-v1.1.1" }, |
| { .compatible = "qcom,i2c-qup-v2.1.1" }, |
| { .compatible = "qcom,i2c-qup-v2.2.1" }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(of, qup_i2c_dt_match); |
| |
| static struct platform_driver qup_i2c_driver = { |
| .probe = qup_i2c_probe, |
| .remove = qup_i2c_remove, |
| .driver = { |
| .name = "i2c_qup", |
| .pm = &qup_i2c_qup_pm_ops, |
| .of_match_table = qup_i2c_dt_match, |
| }, |
| }; |
| |
| module_platform_driver(qup_i2c_driver); |
| |
| MODULE_LICENSE("GPL v2"); |
| MODULE_ALIAS("platform:i2c_qup"); |