| /* |
| * Common Device Tree Source for IGEPv2 |
| * |
| * Copyright (C) 2014 Javier Martinez Canillas <javier@osg.samsung.com> |
| * Copyright (C) 2014 Enric Balletbo i Serra <eballetbo@gmail.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include "omap3-igep.dtsi" |
| #include "omap-gpmc-smsc9221.dtsi" |
| |
| / { |
| |
| leds { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&leds_pins>; |
| compatible = "gpio-leds"; |
| |
| boot { |
| label = "omap3:green:boot"; |
| gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>; |
| default-state = "on"; |
| }; |
| |
| user0 { |
| label = "omap3:red:user0"; |
| gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>; |
| default-state = "off"; |
| }; |
| |
| user1 { |
| label = "omap3:red:user1"; |
| gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; |
| default-state = "off"; |
| }; |
| |
| user2 { |
| label = "omap3:green:user1"; |
| gpios = <&twl_gpio 19 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| /* HS USB Port 1 Power */ |
| hsusb1_power: hsusb1_power_reg { |
| compatible = "regulator-fixed"; |
| regulator-name = "hsusb1_vbus"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* GPIO LEDA */ |
| startup-delay-us = <70000>; |
| }; |
| |
| /* HS USB Host PHY on PORT 1 */ |
| hsusb1_phy: hsusb1_phy { |
| compatible = "usb-nop-xceiv"; |
| reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; /* gpio_24 */ |
| vcc-supply = <&hsusb1_power>; |
| }; |
| |
| tfp410: encoder@0 { |
| compatible = "ti,tfp410"; |
| powerdown-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>; /* gpio_170 */ |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| tfp410_in: endpoint@0 { |
| remote-endpoint = <&dpi_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| tfp410_out: endpoint@0 { |
| remote-endpoint = <&dvi_connector_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| dvi0: connector@0 { |
| compatible = "dvi-connector"; |
| label = "dvi"; |
| |
| digital; |
| |
| ddc-i2c-bus = <&i2c3>; |
| |
| port { |
| dvi_connector_in: endpoint { |
| remote-endpoint = <&tfp410_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| &omap3_pmx_core { |
| pinctrl-names = "default"; |
| pinctrl-0 = < |
| &tfp410_pins |
| &dss_dpi_pins |
| >; |
| |
| tfp410_pins: pinmux_tfp410_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x21c6, PIN_OUTPUT | MUX_MODE4) /* hdq_sio.gpio_170 */ |
| >; |
| }; |
| |
| dss_dpi_pins: pinmux_dss_dpi_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ |
| OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ |
| OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ |
| OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ |
| OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ |
| OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ |
| OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ |
| OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ |
| OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ |
| OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ |
| OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ |
| OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ |
| OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ |
| OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ |
| OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ |
| OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ |
| OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ |
| OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ |
| OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ |
| OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ |
| OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ |
| OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ |
| OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */ |
| OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */ |
| OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */ |
| OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */ |
| OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */ |
| OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */ |
| >; |
| }; |
| |
| uart2_pins: pinmux_uart2_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */ |
| OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/ |
| OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ |
| OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */ |
| >; |
| }; |
| |
| smsc9221_pins: pinmux_smsc9221_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */ |
| >; |
| }; |
| }; |
| |
| &omap3_pmx_core2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = < |
| &hsusbb1_pins |
| >; |
| |
| hsusbb1_pins: pinmux_hsusbb1_pins { |
| pinctrl-single,pins = < |
| OMAP3630_CORE2_IOPAD(0x25da, PIN_OUTPUT | MUX_MODE3) /* etk_ctl.hsusb1_clk */ |
| OMAP3630_CORE2_IOPAD(0x25d8, PIN_OUTPUT | MUX_MODE3) /* etk_clk.hsusb1_stp */ |
| OMAP3630_CORE2_IOPAD(0x25ec, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d8.hsusb1_dir */ |
| OMAP3630_CORE2_IOPAD(0x25ee, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d9.hsusb1_nxt */ |
| OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d0.hsusb1_data0 */ |
| OMAP3630_CORE2_IOPAD(0x25de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d1.hsusb1_data1 */ |
| OMAP3630_CORE2_IOPAD(0x25e0, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d2.hsusb1_data2 */ |
| OMAP3630_CORE2_IOPAD(0x25e2, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d3.hsusb1_data7 */ |
| OMAP3630_CORE2_IOPAD(0x25e4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d4.hsusb1_data4 */ |
| OMAP3630_CORE2_IOPAD(0x25e6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d5.hsusb1_data5 */ |
| OMAP3630_CORE2_IOPAD(0x25e8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d6.hsusb1_data6 */ |
| OMAP3630_CORE2_IOPAD(0x25ea, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d7.hsusb1_data3 */ |
| >; |
| }; |
| |
| leds_pins: pinmux_leds_pins { |
| pinctrl-single,pins = < |
| OMAP3630_CORE2_IOPAD(0x25f4, PIN_OUTPUT | MUX_MODE4) /* etk_d12.gpio_26 */ |
| OMAP3630_CORE2_IOPAD(0x25f6, PIN_OUTPUT | MUX_MODE4) /* etk_d13.gpio_27 */ |
| OMAP3630_CORE2_IOPAD(0x25f8, PIN_OUTPUT | MUX_MODE4) /* etk_d14.gpio_28 */ |
| >; |
| }; |
| |
| mmc1_wp_pins: pinmux_mmc1_cd_pins { |
| pinctrl-single,pins = < |
| OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT | MUX_MODE4) /* etk_d15.gpio_29 */ |
| >; |
| }; |
| }; |
| |
| &i2c3 { |
| clock-frequency = <100000>; |
| |
| /* |
| * Display monitor features are burnt in the EEPROM |
| * as EDID data. |
| */ |
| eeprom@50 { |
| compatible = "ti,eeprom"; |
| reg = <0x50>; |
| }; |
| }; |
| |
| &gpmc { |
| ranges = <0 0 0x30000000 0x01000000>, /* CS0: 16MB for NAND */ |
| <5 0 0x2c000000 0x01000000>; /* CS5: 16MB for ethernet */ |
| |
| ethernet@gpmc { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&smsc9221_pins>; |
| reg = <5 0 0xff>; |
| interrupt-parent = <&gpio6>; |
| interrupts = <16 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| }; |
| |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart2_pins>; |
| }; |
| |
| &usbhshost { |
| port1-mode = "ehci-phy"; |
| }; |
| |
| &usbhsehci { |
| phys = <&hsusb1_phy>; |
| }; |
| |
| &vpll2 { |
| /* Needed for DSS */ |
| regulator-name = "vdds_dsi"; |
| }; |
| |
| &dss { |
| status = "ok"; |
| |
| port { |
| dpi_out: endpoint { |
| remote-endpoint = <&tfp410_in>; |
| data-lines = <24>; |
| }; |
| }; |
| }; |
| |
| &mmc1 { |
| pinctrl-0 = <&mmc1_pins &mmc1_wp_pins>; |
| wp-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>; /* gpio_29 */ |
| }; |
