| #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt |
| |
| #include <linux/kernel.h> |
| #include <linux/export.h> |
| #include <media/drv-intf/saa7146_vv.h> |
| |
| static void calculate_output_format_register(struct saa7146_dev* saa, u32 palette, u32* clip_format) |
| { |
| /* clear out the necessary bits */ |
| *clip_format &= 0x0000ffff; |
| /* set these bits new */ |
| *clip_format |= (( ((palette&0xf00)>>8) << 30) | ((palette&0x00f) << 24) | (((palette&0x0f0)>>4) << 16)); |
| } |
| |
| static void calculate_hps_source_and_sync(struct saa7146_dev *dev, int source, int sync, u32* hps_ctrl) |
| { |
| *hps_ctrl &= ~(MASK_30 | MASK_31 | MASK_28); |
| *hps_ctrl |= (source << 30) | (sync << 28); |
| } |
| |
| static void calculate_hxo_and_hyo(struct saa7146_vv *vv, u32* hps_h_scale, u32* hps_ctrl) |
| { |
| int hyo = 0, hxo = 0; |
| |
| hyo = vv->standard->v_offset; |
| hxo = vv->standard->h_offset; |
| |
| *hps_h_scale &= ~(MASK_B0 | 0xf00); |
| *hps_h_scale |= (hxo << 0); |
| |
| *hps_ctrl &= ~(MASK_W0 | MASK_B2); |
| *hps_ctrl |= (hyo << 12); |
| } |
| |
| /* helper functions for the calculation of the horizontal- and vertical |
| scaling registers, clip-format-register etc ... |
| these functions take pointers to the (most-likely read-out |
| original-values) and manipulate them according to the requested |
| changes. |
| */ |
| |
| /* hps_coeff used for CXY and CXUV; scale 1/1 -> scale 1/64 */ |
| static struct { |
| u16 hps_coeff; |
| u16 weight_sum; |
| } hps_h_coeff_tab [] = { |
| {0x00, 2}, {0x02, 4}, {0x00, 4}, {0x06, 8}, {0x02, 8}, |
| {0x08, 8}, {0x00, 8}, {0x1E, 16}, {0x0E, 8}, {0x26, 8}, |
| {0x06, 8}, {0x42, 8}, {0x02, 8}, {0x80, 8}, {0x00, 8}, |
| {0xFE, 16}, {0xFE, 8}, {0x7E, 8}, {0x7E, 8}, {0x3E, 8}, |
| {0x3E, 8}, {0x1E, 8}, {0x1E, 8}, {0x0E, 8}, {0x0E, 8}, |
| {0x06, 8}, {0x06, 8}, {0x02, 8}, {0x02, 8}, {0x00, 8}, |
| {0x00, 8}, {0xFE, 16}, {0xFE, 8}, {0xFE, 8}, {0xFE, 8}, |
| {0xFE, 8}, {0xFE, 8}, {0xFE, 8}, {0xFE, 8}, {0xFE, 8}, |
| {0xFE, 8}, {0xFE, 8}, {0xFE, 8}, {0xFE, 8}, {0xFE, 8}, |
| {0xFE, 8}, {0xFE, 8}, {0xFE, 8}, {0xFE, 8}, {0x7E, 8}, |
| {0x7E, 8}, {0x3E, 8}, {0x3E, 8}, {0x1E, 8}, {0x1E, 8}, |
| {0x0E, 8}, {0x0E, 8}, {0x06, 8}, {0x06, 8}, {0x02, 8}, |
| {0x02, 8}, {0x00, 8}, {0x00, 8}, {0xFE, 16} |
| }; |
| |
| /* table of attenuation values for horizontal scaling */ |
| static u8 h_attenuation[] = { 1, 2, 4, 8, 2, 4, 8, 16, 0}; |
| |
| /* calculate horizontal scale registers */ |
| static int calculate_h_scale_registers(struct saa7146_dev *dev, |
| int in_x, int out_x, int flip_lr, |
| u32* hps_ctrl, u32* hps_v_gain, u32* hps_h_prescale, u32* hps_h_scale) |
| { |
| /* horizontal prescaler */ |
| u32 dcgx = 0, xpsc = 0, xacm = 0, cxy = 0, cxuv = 0; |
| /* horizontal scaler */ |
| u32 xim = 0, xp = 0, xsci =0; |
| /* vertical scale & gain */ |
| u32 pfuv = 0; |
| |
| /* helper variables */ |
| u32 h_atten = 0, i = 0; |
| |
| if ( 0 == out_x ) { |
| return -EINVAL; |
| } |
| |
| /* mask out vanity-bit */ |
| *hps_ctrl &= ~MASK_29; |
| |
| /* calculate prescale-(xspc)-value: [n .. 1/2) : 1 |
| [1/2 .. 1/3) : 2 |
| [1/3 .. 1/4) : 3 |
| ... */ |
| if (in_x > out_x) { |
| xpsc = in_x / out_x; |
| } |
| else { |
| /* zooming */ |
| xpsc = 1; |
| } |
| |
| /* if flip_lr-bit is set, number of pixels after |
| horizontal prescaling must be < 384 */ |
| if ( 0 != flip_lr ) { |
| |
| /* set vanity bit */ |
| *hps_ctrl |= MASK_29; |
| |
| while (in_x / xpsc >= 384 ) |
| xpsc++; |
| } |
| /* if zooming is wanted, number of pixels after |
| horizontal prescaling must be < 768 */ |
| else { |
| while ( in_x / xpsc >= 768 ) |
| xpsc++; |
| } |
| |
| /* maximum prescale is 64 (p.69) */ |
| if ( xpsc > 64 ) |
| xpsc = 64; |
| |
| /* keep xacm clear*/ |
| xacm = 0; |
| |
| /* set horizontal filter parameters (CXY = CXUV) */ |
| cxy = hps_h_coeff_tab[( (xpsc - 1) < 63 ? (xpsc - 1) : 63 )].hps_coeff; |
| cxuv = cxy; |
| |
| /* calculate and set horizontal fine scale (xsci) */ |
| |
| /* bypass the horizontal scaler ? */ |
| if ( (in_x == out_x) && ( 1 == xpsc ) ) |
| xsci = 0x400; |
| else |
| xsci = ( (1024 * in_x) / (out_x * xpsc) ) + xpsc; |
| |
| /* set start phase for horizontal fine scale (xp) to 0 */ |
| xp = 0; |
| |
| /* set xim, if we bypass the horizontal scaler */ |
| if ( 0x400 == xsci ) |
| xim = 1; |
| else |
| xim = 0; |
| |
| /* if the prescaler is bypassed, enable horizontal |
| accumulation mode (xacm) and clear dcgx */ |
| if( 1 == xpsc ) { |
| xacm = 1; |
| dcgx = 0; |
| } else { |
| xacm = 0; |
| /* get best match in the table of attenuations |
| for horizontal scaling */ |
| h_atten = hps_h_coeff_tab[( (xpsc - 1) < 63 ? (xpsc - 1) : 63 )].weight_sum; |
| |
| for (i = 0; h_attenuation[i] != 0; i++) { |
| if (h_attenuation[i] >= h_atten) |
| break; |
| } |
| |
| dcgx = i; |
| } |
| |
| /* the horizontal scaling increment controls the UV filter |
| to reduce the bandwidth to improve the display quality, |
| so set it ... */ |
| if ( xsci == 0x400) |
| pfuv = 0x00; |
| else if ( xsci < 0x600) |
| pfuv = 0x01; |
| else if ( xsci < 0x680) |
| pfuv = 0x11; |
| else if ( xsci < 0x700) |
| pfuv = 0x22; |
| else |
| pfuv = 0x33; |
| |
| |
| *hps_v_gain &= MASK_W0|MASK_B2; |
| *hps_v_gain |= (pfuv << 24); |
| |
| *hps_h_scale &= ~(MASK_W1 | 0xf000); |
| *hps_h_scale |= (xim << 31) | (xp << 24) | (xsci << 12); |
| |
| *hps_h_prescale |= (dcgx << 27) | ((xpsc-1) << 18) | (xacm << 17) | (cxy << 8) | (cxuv << 0); |
| |
| return 0; |
| } |
| |
| static struct { |
| u16 hps_coeff; |
| u16 weight_sum; |
| } hps_v_coeff_tab [] = { |
| {0x0100, 2}, {0x0102, 4}, {0x0300, 4}, {0x0106, 8}, {0x0502, 8}, |
| {0x0708, 8}, {0x0F00, 8}, {0x011E, 16}, {0x110E, 16}, {0x1926, 16}, |
| {0x3906, 16}, {0x3D42, 16}, {0x7D02, 16}, {0x7F80, 16}, {0xFF00, 16}, |
| {0x01FE, 32}, {0x01FE, 32}, {0x817E, 32}, {0x817E, 32}, {0xC13E, 32}, |
| {0xC13E, 32}, {0xE11E, 32}, {0xE11E, 32}, {0xF10E, 32}, {0xF10E, 32}, |
| {0xF906, 32}, {0xF906, 32}, {0xFD02, 32}, {0xFD02, 32}, {0xFF00, 32}, |
| {0xFF00, 32}, {0x01FE, 64}, {0x01FE, 64}, {0x01FE, 64}, {0x01FE, 64}, |
| {0x01FE, 64}, {0x01FE, 64}, {0x01FE, 64}, {0x01FE, 64}, {0x01FE, 64}, |
| {0x01FE, 64}, {0x01FE, 64}, {0x01FE, 64}, {0x01FE, 64}, {0x01FE, 64}, |
| {0x01FE, 64}, {0x01FE, 64}, {0x01FE, 64}, {0x01FE, 64}, {0x817E, 64}, |
| {0x817E, 64}, {0xC13E, 64}, {0xC13E, 64}, {0xE11E, 64}, {0xE11E, 64}, |
| {0xF10E, 64}, {0xF10E, 64}, {0xF906, 64}, {0xF906, 64}, {0xFD02, 64}, |
| {0xFD02, 64}, {0xFF00, 64}, {0xFF00, 64}, {0x01FE, 128} |
| }; |
| |
| /* table of attenuation values for vertical scaling */ |
| static u16 v_attenuation[] = { 2, 4, 8, 16, 32, 64, 128, 256, 0}; |
| |
| /* calculate vertical scale registers */ |
| static int calculate_v_scale_registers(struct saa7146_dev *dev, enum v4l2_field field, |
| int in_y, int out_y, u32* hps_v_scale, u32* hps_v_gain) |
| { |
| int lpi = 0; |
| |
| /* vertical scaling */ |
| u32 yacm = 0, ysci = 0, yacl = 0, ypo = 0, ype = 0; |
| /* vertical scale & gain */ |
| u32 dcgy = 0, cya_cyb = 0; |
| |
| /* helper variables */ |
| u32 v_atten = 0, i = 0; |
| |
| /* error, if vertical zooming */ |
| if ( in_y < out_y ) { |
| return -EINVAL; |
| } |
| |
| /* linear phase interpolation may be used |
| if scaling is between 1 and 1/2 (both fields used) |
| or scaling is between 1/2 and 1/4 (if only one field is used) */ |
| |
| if (V4L2_FIELD_HAS_BOTH(field)) { |
| if( 2*out_y >= in_y) { |
| lpi = 1; |
| } |
| } else if (field == V4L2_FIELD_TOP |
| || field == V4L2_FIELD_ALTERNATE |
| || field == V4L2_FIELD_BOTTOM) { |
| if( 4*out_y >= in_y ) { |
| lpi = 1; |
| } |
| out_y *= 2; |
| } |
| if( 0 != lpi ) { |
| |
| yacm = 0; |
| yacl = 0; |
| cya_cyb = 0x00ff; |
| |
| /* calculate scaling increment */ |
| if ( in_y > out_y ) |
| ysci = ((1024 * in_y) / (out_y + 1)) - 1024; |
| else |
| ysci = 0; |
| |
| dcgy = 0; |
| |
| /* calculate ype and ypo */ |
| ype = ysci / 16; |
| ypo = ype + (ysci / 64); |
| |
| } else { |
| yacm = 1; |
| |
| /* calculate scaling increment */ |
| ysci = (((10 * 1024 * (in_y - out_y - 1)) / in_y) + 9) / 10; |
| |
| /* calculate ype and ypo */ |
| ypo = ype = ((ysci + 15) / 16); |
| |
| /* the sequence length interval (yacl) has to be set according |
| to the prescale value, e.g. [n .. 1/2) : 0 |
| [1/2 .. 1/3) : 1 |
| [1/3 .. 1/4) : 2 |
| ... */ |
| if ( ysci < 512) { |
| yacl = 0; |
| } else { |
| yacl = ( ysci / (1024 - ysci) ); |
| } |
| |
| /* get filter coefficients for cya, cyb from table hps_v_coeff_tab */ |
| cya_cyb = hps_v_coeff_tab[ (yacl < 63 ? yacl : 63 ) ].hps_coeff; |
| |
| /* get best match in the table of attenuations for vertical scaling */ |
| v_atten = hps_v_coeff_tab[ (yacl < 63 ? yacl : 63 ) ].weight_sum; |
| |
| for (i = 0; v_attenuation[i] != 0; i++) { |
| if (v_attenuation[i] >= v_atten) |
| break; |
| } |
| |
| dcgy = i; |
| } |
| |
| /* ypo and ype swapped in spec ? */ |
| *hps_v_scale |= (yacm << 31) | (ysci << 21) | (yacl << 15) | (ypo << 8 ) | (ype << 1); |
| |
| *hps_v_gain &= ~(MASK_W0|MASK_B2); |
| *hps_v_gain |= (dcgy << 16) | (cya_cyb << 0); |
| |
| return 0; |
| } |
| |
| /* simple bubble-sort algorithm with duplicate elimination */ |
| static int sort_and_eliminate(u32* values, int* count) |
| { |
| int low = 0, high = 0, top = 0; |
| int cur = 0, next = 0; |
| |
| /* sanity checks */ |
| if( (0 > *count) || (NULL == values) ) { |
| return -EINVAL; |
| } |
| |
| /* bubble sort the first @count items of the array @values */ |
| for( top = *count; top > 0; top--) { |
| for( low = 0, high = 1; high < top; low++, high++) { |
| if( values[low] > values[high] ) |
| swap(values[low], values[high]); |
| } |
| } |
| |
| /* remove duplicate items */ |
| for( cur = 0, next = 1; next < *count; next++) { |
| if( values[cur] != values[next]) |
| values[++cur] = values[next]; |
| } |
| |
| *count = cur + 1; |
| |
| return 0; |
| } |
| |
| static void calculate_clipping_registers_rect(struct saa7146_dev *dev, struct saa7146_fh *fh, |
| struct saa7146_video_dma *vdma2, u32* clip_format, u32* arbtr_ctrl, enum v4l2_field field) |
| { |
| struct saa7146_vv *vv = dev->vv_data; |
| __le32 *clipping = vv->d_clipping.cpu_addr; |
| |
| int width = vv->ov.win.w.width; |
| int height = vv->ov.win.w.height; |
| int clipcount = vv->ov.nclips; |
| |
| u32 line_list[32]; |
| u32 pixel_list[32]; |
| int numdwords = 0; |
| |
| int i = 0, j = 0; |
| int cnt_line = 0, cnt_pixel = 0; |
| |
| int x[32], y[32], w[32], h[32]; |
| |
| /* clear out memory */ |
| memset(&line_list[0], 0x00, sizeof(u32)*32); |
| memset(&pixel_list[0], 0x00, sizeof(u32)*32); |
| memset(clipping, 0x00, SAA7146_CLIPPING_MEM); |
| |
| /* fill the line and pixel-lists */ |
| for(i = 0; i < clipcount; i++) { |
| int l = 0, r = 0, t = 0, b = 0; |
| |
| x[i] = vv->ov.clips[i].c.left; |
| y[i] = vv->ov.clips[i].c.top; |
| w[i] = vv->ov.clips[i].c.width; |
| h[i] = vv->ov.clips[i].c.height; |
| |
| if( w[i] < 0) { |
| x[i] += w[i]; w[i] = -w[i]; |
| } |
| if( h[i] < 0) { |
| y[i] += h[i]; h[i] = -h[i]; |
| } |
| if( x[i] < 0) { |
| w[i] += x[i]; x[i] = 0; |
| } |
| if( y[i] < 0) { |
| h[i] += y[i]; y[i] = 0; |
| } |
| if( 0 != vv->vflip ) { |
| y[i] = height - y[i] - h[i]; |
| } |
| |
| l = x[i]; |
| r = x[i]+w[i]; |
| t = y[i]; |
| b = y[i]+h[i]; |
| |
| /* insert left/right coordinates */ |
| pixel_list[ 2*i ] = min_t(int, l, width); |
| pixel_list[(2*i)+1] = min_t(int, r, width); |
| /* insert top/bottom coordinates */ |
| line_list[ 2*i ] = min_t(int, t, height); |
| line_list[(2*i)+1] = min_t(int, b, height); |
| } |
| |
| /* sort and eliminate lists */ |
| cnt_line = cnt_pixel = 2*clipcount; |
| sort_and_eliminate( &pixel_list[0], &cnt_pixel ); |
| sort_and_eliminate( &line_list[0], &cnt_line ); |
| |
| /* calculate the number of used u32s */ |
| numdwords = max_t(int, (cnt_line+1), (cnt_pixel+1))*2; |
| numdwords = max_t(int, 4, numdwords); |
| numdwords = min_t(int, 64, numdwords); |
| |
| /* fill up cliptable */ |
| for(i = 0; i < cnt_pixel; i++) { |
| clipping[2*i] |= cpu_to_le32(pixel_list[i] << 16); |
| } |
| for(i = 0; i < cnt_line; i++) { |
| clipping[(2*i)+1] |= cpu_to_le32(line_list[i] << 16); |
| } |
| |
| /* fill up cliptable with the display infos */ |
| for(j = 0; j < clipcount; j++) { |
| |
| for(i = 0; i < cnt_pixel; i++) { |
| |
| if( x[j] < 0) |
| x[j] = 0; |
| |
| if( pixel_list[i] < (x[j] + w[j])) { |
| |
| if ( pixel_list[i] >= x[j] ) { |
| clipping[2*i] |= cpu_to_le32(1 << j); |
| } |
| } |
| } |
| for(i = 0; i < cnt_line; i++) { |
| |
| if( y[j] < 0) |
| y[j] = 0; |
| |
| if( line_list[i] < (y[j] + h[j]) ) { |
| |
| if( line_list[i] >= y[j] ) { |
| clipping[(2*i)+1] |= cpu_to_le32(1 << j); |
| } |
| } |
| } |
| } |
| |
| /* adjust arbitration control register */ |
| *arbtr_ctrl &= 0xffff00ff; |
| *arbtr_ctrl |= 0x00001c00; |
| |
| vdma2->base_even = vv->d_clipping.dma_handle; |
| vdma2->base_odd = vv->d_clipping.dma_handle; |
| vdma2->prot_addr = vv->d_clipping.dma_handle+((sizeof(u32))*(numdwords)); |
| vdma2->base_page = 0x04; |
| vdma2->pitch = 0x00; |
| vdma2->num_line_byte = (0 << 16 | (sizeof(u32))*(numdwords-1) ); |
| |
| /* set clipping-mode. this depends on the field(s) used */ |
| *clip_format &= 0xfffffff7; |
| if (V4L2_FIELD_HAS_BOTH(field)) { |
| *clip_format |= 0x00000008; |
| } else { |
| *clip_format |= 0x00000000; |
| } |
| } |
| |
| /* disable clipping */ |
| static void saa7146_disable_clipping(struct saa7146_dev *dev) |
| { |
| u32 clip_format = saa7146_read(dev, CLIP_FORMAT_CTRL); |
| |
| /* mask out relevant bits (=lower word)*/ |
| clip_format &= MASK_W1; |
| |
| /* upload clipping-registers*/ |
| saa7146_write(dev, CLIP_FORMAT_CTRL,clip_format); |
| saa7146_write(dev, MC2, (MASK_05 | MASK_21)); |
| |
| /* disable video dma2 */ |
| saa7146_write(dev, MC1, MASK_21); |
| } |
| |
| static void saa7146_set_clipping_rect(struct saa7146_fh *fh) |
| { |
| struct saa7146_dev *dev = fh->dev; |
| struct saa7146_vv *vv = dev->vv_data; |
| enum v4l2_field field = vv->ov.win.field; |
| struct saa7146_video_dma vdma2; |
| u32 clip_format; |
| u32 arbtr_ctrl; |
| |
| /* check clipcount, disable clipping if clipcount == 0*/ |
| if (vv->ov.nclips == 0) { |
| saa7146_disable_clipping(dev); |
| return; |
| } |
| |
| clip_format = saa7146_read(dev, CLIP_FORMAT_CTRL); |
| arbtr_ctrl = saa7146_read(dev, PCI_BT_V1); |
| |
| calculate_clipping_registers_rect(dev, fh, &vdma2, &clip_format, &arbtr_ctrl, field); |
| |
| /* set clipping format */ |
| clip_format &= 0xffff0008; |
| clip_format |= (SAA7146_CLIPPING_RECT << 4); |
| |
| /* prepare video dma2 */ |
| saa7146_write(dev, BASE_EVEN2, vdma2.base_even); |
| saa7146_write(dev, BASE_ODD2, vdma2.base_odd); |
| saa7146_write(dev, PROT_ADDR2, vdma2.prot_addr); |
| saa7146_write(dev, BASE_PAGE2, vdma2.base_page); |
| saa7146_write(dev, PITCH2, vdma2.pitch); |
| saa7146_write(dev, NUM_LINE_BYTE2, vdma2.num_line_byte); |
| |
| /* prepare the rest */ |
| saa7146_write(dev, CLIP_FORMAT_CTRL,clip_format); |
| saa7146_write(dev, PCI_BT_V1, arbtr_ctrl); |
| |
| /* upload clip_control-register, clipping-registers, enable video dma2 */ |
| saa7146_write(dev, MC2, (MASK_05 | MASK_21 | MASK_03 | MASK_19)); |
| saa7146_write(dev, MC1, (MASK_05 | MASK_21)); |
| } |
| |
| static void saa7146_set_window(struct saa7146_dev *dev, int width, int height, enum v4l2_field field) |
| { |
| struct saa7146_vv *vv = dev->vv_data; |
| |
| int source = vv->current_hps_source; |
| int sync = vv->current_hps_sync; |
| |
| u32 hps_v_scale = 0, hps_v_gain = 0, hps_ctrl = 0, hps_h_prescale = 0, hps_h_scale = 0; |
| |
| /* set vertical scale */ |
| hps_v_scale = 0; /* all bits get set by the function-call */ |
| hps_v_gain = 0; /* fixme: saa7146_read(dev, HPS_V_GAIN);*/ |
| calculate_v_scale_registers(dev, field, vv->standard->v_field*2, height, &hps_v_scale, &hps_v_gain); |
| |
| /* set horizontal scale */ |
| hps_ctrl = 0; |
| hps_h_prescale = 0; /* all bits get set in the function */ |
| hps_h_scale = 0; |
| calculate_h_scale_registers(dev, vv->standard->h_pixels, width, vv->hflip, &hps_ctrl, &hps_v_gain, &hps_h_prescale, &hps_h_scale); |
| |
| /* set hyo and hxo */ |
| calculate_hxo_and_hyo(vv, &hps_h_scale, &hps_ctrl); |
| calculate_hps_source_and_sync(dev, source, sync, &hps_ctrl); |
| |
| /* write out new register contents */ |
| saa7146_write(dev, HPS_V_SCALE, hps_v_scale); |
| saa7146_write(dev, HPS_V_GAIN, hps_v_gain); |
| saa7146_write(dev, HPS_CTRL, hps_ctrl); |
| saa7146_write(dev, HPS_H_PRESCALE,hps_h_prescale); |
| saa7146_write(dev, HPS_H_SCALE, hps_h_scale); |
| |
| /* upload shadow-ram registers */ |
| saa7146_write(dev, MC2, (MASK_05 | MASK_06 | MASK_21 | MASK_22) ); |
| } |
| |
| /* calculate the new memory offsets for a desired position */ |
| static void saa7146_set_position(struct saa7146_dev *dev, int w_x, int w_y, int w_height, enum v4l2_field field, u32 pixelformat) |
| { |
| struct saa7146_vv *vv = dev->vv_data; |
| struct saa7146_format *sfmt = saa7146_format_by_fourcc(dev, pixelformat); |
| |
| int b_depth = vv->ov_fmt->depth; |
| int b_bpl = vv->ov_fb.fmt.bytesperline; |
| /* The unsigned long cast is to remove a 64-bit compile warning since |
| it looks like a 64-bit address is cast to a 32-bit value, even |
| though the base pointer is really a 32-bit physical address that |
| goes into a 32-bit DMA register. |
| FIXME: might not work on some 64-bit platforms, but see the FIXME |
| in struct v4l2_framebuffer (videodev2.h) for that. |
| */ |
| u32 base = (u32)(unsigned long)vv->ov_fb.base; |
| |
| struct saa7146_video_dma vdma1; |
| |
| /* calculate memory offsets for picture, look if we shall top-down-flip */ |
| vdma1.pitch = 2*b_bpl; |
| if ( 0 == vv->vflip ) { |
| vdma1.base_even = base + (w_y * (vdma1.pitch/2)) + (w_x * (b_depth / 8)); |
| vdma1.base_odd = vdma1.base_even + (vdma1.pitch / 2); |
| vdma1.prot_addr = vdma1.base_even + (w_height * (vdma1.pitch / 2)); |
| } |
| else { |
| vdma1.base_even = base + ((w_y+w_height) * (vdma1.pitch/2)) + (w_x * (b_depth / 8)); |
| vdma1.base_odd = vdma1.base_even - (vdma1.pitch / 2); |
| vdma1.prot_addr = vdma1.base_odd - (w_height * (vdma1.pitch / 2)); |
| } |
| |
| if (V4L2_FIELD_HAS_BOTH(field)) { |
| } else if (field == V4L2_FIELD_ALTERNATE) { |
| /* fixme */ |
| vdma1.base_odd = vdma1.prot_addr; |
| vdma1.pitch /= 2; |
| } else if (field == V4L2_FIELD_TOP) { |
| vdma1.base_odd = vdma1.prot_addr; |
| vdma1.pitch /= 2; |
| } else if (field == V4L2_FIELD_BOTTOM) { |
| vdma1.base_odd = vdma1.base_even; |
| vdma1.base_even = vdma1.prot_addr; |
| vdma1.pitch /= 2; |
| } |
| |
| if ( 0 != vv->vflip ) { |
| vdma1.pitch *= -1; |
| } |
| |
| vdma1.base_page = sfmt->swap; |
| vdma1.num_line_byte = (vv->standard->v_field<<16)+vv->standard->h_pixels; |
| |
| saa7146_write_out_dma(dev, 1, &vdma1); |
| } |
| |
| static void saa7146_set_output_format(struct saa7146_dev *dev, unsigned long palette) |
| { |
| u32 clip_format = saa7146_read(dev, CLIP_FORMAT_CTRL); |
| |
| /* call helper function */ |
| calculate_output_format_register(dev,palette,&clip_format); |
| |
| /* update the hps registers */ |
| saa7146_write(dev, CLIP_FORMAT_CTRL, clip_format); |
| saa7146_write(dev, MC2, (MASK_05 | MASK_21)); |
| } |
| |
| /* select input-source */ |
| void saa7146_set_hps_source_and_sync(struct saa7146_dev *dev, int source, int sync) |
| { |
| struct saa7146_vv *vv = dev->vv_data; |
| u32 hps_ctrl = 0; |
| |
| /* read old state */ |
| hps_ctrl = saa7146_read(dev, HPS_CTRL); |
| |
| hps_ctrl &= ~( MASK_31 | MASK_30 | MASK_28 ); |
| hps_ctrl |= (source << 30) | (sync << 28); |
| |
| /* write back & upload register */ |
| saa7146_write(dev, HPS_CTRL, hps_ctrl); |
| saa7146_write(dev, MC2, (MASK_05 | MASK_21)); |
| |
| vv->current_hps_source = source; |
| vv->current_hps_sync = sync; |
| } |
| EXPORT_SYMBOL_GPL(saa7146_set_hps_source_and_sync); |
| |
| int saa7146_enable_overlay(struct saa7146_fh *fh) |
| { |
| struct saa7146_dev *dev = fh->dev; |
| struct saa7146_vv *vv = dev->vv_data; |
| |
| saa7146_set_window(dev, vv->ov.win.w.width, vv->ov.win.w.height, vv->ov.win.field); |
| saa7146_set_position(dev, vv->ov.win.w.left, vv->ov.win.w.top, vv->ov.win.w.height, vv->ov.win.field, vv->ov_fmt->pixelformat); |
| saa7146_set_output_format(dev, vv->ov_fmt->trans); |
| saa7146_set_clipping_rect(fh); |
| |
| /* enable video dma1 */ |
| saa7146_write(dev, MC1, (MASK_06 | MASK_22)); |
| return 0; |
| } |
| |
| void saa7146_disable_overlay(struct saa7146_fh *fh) |
| { |
| struct saa7146_dev *dev = fh->dev; |
| |
| /* disable clipping + video dma1 */ |
| saa7146_disable_clipping(dev); |
| saa7146_write(dev, MC1, MASK_22); |
| } |
| |
| void saa7146_write_out_dma(struct saa7146_dev* dev, int which, struct saa7146_video_dma* vdma) |
| { |
| int where = 0; |
| |
| if( which < 1 || which > 3) { |
| return; |
| } |
| |
| /* calculate starting address */ |
| where = (which-1)*0x18; |
| |
| saa7146_write(dev, where, vdma->base_odd); |
| saa7146_write(dev, where+0x04, vdma->base_even); |
| saa7146_write(dev, where+0x08, vdma->prot_addr); |
| saa7146_write(dev, where+0x0c, vdma->pitch); |
| saa7146_write(dev, where+0x10, vdma->base_page); |
| saa7146_write(dev, where+0x14, vdma->num_line_byte); |
| |
| /* upload */ |
| saa7146_write(dev, MC2, (MASK_02<<(which-1))|(MASK_18<<(which-1))); |
| /* |
| printk("vdma%d.base_even: 0x%08x\n", which,vdma->base_even); |
| printk("vdma%d.base_odd: 0x%08x\n", which,vdma->base_odd); |
| printk("vdma%d.prot_addr: 0x%08x\n", which,vdma->prot_addr); |
| printk("vdma%d.base_page: 0x%08x\n", which,vdma->base_page); |
| printk("vdma%d.pitch: 0x%08x\n", which,vdma->pitch); |
| printk("vdma%d.num_line_byte: 0x%08x\n", which,vdma->num_line_byte); |
| */ |
| } |
| |
| static int calculate_video_dma_grab_packed(struct saa7146_dev* dev, struct saa7146_buf *buf) |
| { |
| struct saa7146_vv *vv = dev->vv_data; |
| struct saa7146_video_dma vdma1; |
| |
| struct saa7146_format *sfmt = saa7146_format_by_fourcc(dev,buf->fmt->pixelformat); |
| |
| int width = buf->fmt->width; |
| int height = buf->fmt->height; |
| int bytesperline = buf->fmt->bytesperline; |
| enum v4l2_field field = buf->fmt->field; |
| |
| int depth = sfmt->depth; |
| |
| DEB_CAP("[size=%dx%d,fields=%s]\n", |
| width, height, v4l2_field_names[field]); |
| |
| if( bytesperline != 0) { |
| vdma1.pitch = bytesperline*2; |
| } else { |
| vdma1.pitch = (width*depth*2)/8; |
| } |
| vdma1.num_line_byte = ((vv->standard->v_field<<16) + vv->standard->h_pixels); |
| vdma1.base_page = buf->pt[0].dma | ME1 | sfmt->swap; |
| |
| if( 0 != vv->vflip ) { |
| vdma1.prot_addr = buf->pt[0].offset; |
| vdma1.base_even = buf->pt[0].offset+(vdma1.pitch/2)*height; |
| vdma1.base_odd = vdma1.base_even - (vdma1.pitch/2); |
| } else { |
| vdma1.base_even = buf->pt[0].offset; |
| vdma1.base_odd = vdma1.base_even + (vdma1.pitch/2); |
| vdma1.prot_addr = buf->pt[0].offset+(vdma1.pitch/2)*height; |
| } |
| |
| if (V4L2_FIELD_HAS_BOTH(field)) { |
| } else if (field == V4L2_FIELD_ALTERNATE) { |
| /* fixme */ |
| if ( vv->last_field == V4L2_FIELD_TOP ) { |
| vdma1.base_odd = vdma1.prot_addr; |
| vdma1.pitch /= 2; |
| } else if ( vv->last_field == V4L2_FIELD_BOTTOM ) { |
| vdma1.base_odd = vdma1.base_even; |
| vdma1.base_even = vdma1.prot_addr; |
| vdma1.pitch /= 2; |
| } |
| } else if (field == V4L2_FIELD_TOP) { |
| vdma1.base_odd = vdma1.prot_addr; |
| vdma1.pitch /= 2; |
| } else if (field == V4L2_FIELD_BOTTOM) { |
| vdma1.base_odd = vdma1.base_even; |
| vdma1.base_even = vdma1.prot_addr; |
| vdma1.pitch /= 2; |
| } |
| |
| if( 0 != vv->vflip ) { |
| vdma1.pitch *= -1; |
| } |
| |
| saa7146_write_out_dma(dev, 1, &vdma1); |
| return 0; |
| } |
| |
| static int calc_planar_422(struct saa7146_vv *vv, struct saa7146_buf *buf, struct saa7146_video_dma *vdma2, struct saa7146_video_dma *vdma3) |
| { |
| int height = buf->fmt->height; |
| int width = buf->fmt->width; |
| |
| vdma2->pitch = width; |
| vdma3->pitch = width; |
| |
| /* fixme: look at bytesperline! */ |
| |
| if( 0 != vv->vflip ) { |
| vdma2->prot_addr = buf->pt[1].offset; |
| vdma2->base_even = ((vdma2->pitch/2)*height)+buf->pt[1].offset; |
| vdma2->base_odd = vdma2->base_even - (vdma2->pitch/2); |
| |
| vdma3->prot_addr = buf->pt[2].offset; |
| vdma3->base_even = ((vdma3->pitch/2)*height)+buf->pt[2].offset; |
| vdma3->base_odd = vdma3->base_even - (vdma3->pitch/2); |
| } else { |
| vdma3->base_even = buf->pt[2].offset; |
| vdma3->base_odd = vdma3->base_even + (vdma3->pitch/2); |
| vdma3->prot_addr = (vdma3->pitch/2)*height+buf->pt[2].offset; |
| |
| vdma2->base_even = buf->pt[1].offset; |
| vdma2->base_odd = vdma2->base_even + (vdma2->pitch/2); |
| vdma2->prot_addr = (vdma2->pitch/2)*height+buf->pt[1].offset; |
| } |
| |
| return 0; |
| } |
| |
| static int calc_planar_420(struct saa7146_vv *vv, struct saa7146_buf *buf, struct saa7146_video_dma *vdma2, struct saa7146_video_dma *vdma3) |
| { |
| int height = buf->fmt->height; |
| int width = buf->fmt->width; |
| |
| vdma2->pitch = width/2; |
| vdma3->pitch = width/2; |
| |
| if( 0 != vv->vflip ) { |
| vdma2->prot_addr = buf->pt[2].offset; |
| vdma2->base_even = ((vdma2->pitch/2)*height)+buf->pt[2].offset; |
| vdma2->base_odd = vdma2->base_even - (vdma2->pitch/2); |
| |
| vdma3->prot_addr = buf->pt[1].offset; |
| vdma3->base_even = ((vdma3->pitch/2)*height)+buf->pt[1].offset; |
| vdma3->base_odd = vdma3->base_even - (vdma3->pitch/2); |
| |
| } else { |
| vdma3->base_even = buf->pt[2].offset; |
| vdma3->base_odd = vdma3->base_even + (vdma3->pitch); |
| vdma3->prot_addr = (vdma3->pitch/2)*height+buf->pt[2].offset; |
| |
| vdma2->base_even = buf->pt[1].offset; |
| vdma2->base_odd = vdma2->base_even + (vdma2->pitch); |
| vdma2->prot_addr = (vdma2->pitch/2)*height+buf->pt[1].offset; |
| } |
| return 0; |
| } |
| |
| static int calculate_video_dma_grab_planar(struct saa7146_dev* dev, struct saa7146_buf *buf) |
| { |
| struct saa7146_vv *vv = dev->vv_data; |
| struct saa7146_video_dma vdma1; |
| struct saa7146_video_dma vdma2; |
| struct saa7146_video_dma vdma3; |
| |
| struct saa7146_format *sfmt = saa7146_format_by_fourcc(dev,buf->fmt->pixelformat); |
| |
| int width = buf->fmt->width; |
| int height = buf->fmt->height; |
| enum v4l2_field field = buf->fmt->field; |
| |
| BUG_ON(0 == buf->pt[0].dma); |
| BUG_ON(0 == buf->pt[1].dma); |
| BUG_ON(0 == buf->pt[2].dma); |
| |
| DEB_CAP("[size=%dx%d,fields=%s]\n", |
| width, height, v4l2_field_names[field]); |
| |
| /* fixme: look at bytesperline! */ |
| |
| /* fixme: what happens for user space buffers here?. The offsets are |
| most likely wrong, this version here only works for page-aligned |
| buffers, modifications to the pagetable-functions are necessary...*/ |
| |
| vdma1.pitch = width*2; |
| vdma1.num_line_byte = ((vv->standard->v_field<<16) + vv->standard->h_pixels); |
| vdma1.base_page = buf->pt[0].dma | ME1; |
| |
| if( 0 != vv->vflip ) { |
| vdma1.prot_addr = buf->pt[0].offset; |
| vdma1.base_even = ((vdma1.pitch/2)*height)+buf->pt[0].offset; |
| vdma1.base_odd = vdma1.base_even - (vdma1.pitch/2); |
| } else { |
| vdma1.base_even = buf->pt[0].offset; |
| vdma1.base_odd = vdma1.base_even + (vdma1.pitch/2); |
| vdma1.prot_addr = (vdma1.pitch/2)*height+buf->pt[0].offset; |
| } |
| |
| vdma2.num_line_byte = 0; /* unused */ |
| vdma2.base_page = buf->pt[1].dma | ME1; |
| |
| vdma3.num_line_byte = 0; /* unused */ |
| vdma3.base_page = buf->pt[2].dma | ME1; |
| |
| switch( sfmt->depth ) { |
| case 12: { |
| calc_planar_420(vv,buf,&vdma2,&vdma3); |
| break; |
| } |
| case 16: { |
| calc_planar_422(vv,buf,&vdma2,&vdma3); |
| break; |
| } |
| default: { |
| return -1; |
| } |
| } |
| |
| if (V4L2_FIELD_HAS_BOTH(field)) { |
| } else if (field == V4L2_FIELD_ALTERNATE) { |
| /* fixme */ |
| vdma1.base_odd = vdma1.prot_addr; |
| vdma1.pitch /= 2; |
| vdma2.base_odd = vdma2.prot_addr; |
| vdma2.pitch /= 2; |
| vdma3.base_odd = vdma3.prot_addr; |
| vdma3.pitch /= 2; |
| } else if (field == V4L2_FIELD_TOP) { |
| vdma1.base_odd = vdma1.prot_addr; |
| vdma1.pitch /= 2; |
| vdma2.base_odd = vdma2.prot_addr; |
| vdma2.pitch /= 2; |
| vdma3.base_odd = vdma3.prot_addr; |
| vdma3.pitch /= 2; |
| } else if (field == V4L2_FIELD_BOTTOM) { |
| vdma1.base_odd = vdma1.base_even; |
| vdma1.base_even = vdma1.prot_addr; |
| vdma1.pitch /= 2; |
| vdma2.base_odd = vdma2.base_even; |
| vdma2.base_even = vdma2.prot_addr; |
| vdma2.pitch /= 2; |
| vdma3.base_odd = vdma3.base_even; |
| vdma3.base_even = vdma3.prot_addr; |
| vdma3.pitch /= 2; |
| } |
| |
| if( 0 != vv->vflip ) { |
| vdma1.pitch *= -1; |
| vdma2.pitch *= -1; |
| vdma3.pitch *= -1; |
| } |
| |
| saa7146_write_out_dma(dev, 1, &vdma1); |
| if( (sfmt->flags & FORMAT_BYTE_SWAP) != 0 ) { |
| saa7146_write_out_dma(dev, 3, &vdma2); |
| saa7146_write_out_dma(dev, 2, &vdma3); |
| } else { |
| saa7146_write_out_dma(dev, 2, &vdma2); |
| saa7146_write_out_dma(dev, 3, &vdma3); |
| } |
| return 0; |
| } |
| |
| static void program_capture_engine(struct saa7146_dev *dev, int planar) |
| { |
| struct saa7146_vv *vv = dev->vv_data; |
| int count = 0; |
| |
| unsigned long e_wait = vv->current_hps_sync == SAA7146_HPS_SYNC_PORT_A ? CMD_E_FID_A : CMD_E_FID_B; |
| unsigned long o_wait = vv->current_hps_sync == SAA7146_HPS_SYNC_PORT_A ? CMD_O_FID_A : CMD_O_FID_B; |
| |
| /* wait for o_fid_a/b / e_fid_a/b toggle only if rps register 0 is not set*/ |
| WRITE_RPS0(CMD_PAUSE | CMD_OAN | CMD_SIG0 | o_wait); |
| WRITE_RPS0(CMD_PAUSE | CMD_OAN | CMD_SIG0 | e_wait); |
| |
| /* set rps register 0 */ |
| WRITE_RPS0(CMD_WR_REG | (1 << 8) | (MC2/4)); |
| WRITE_RPS0(MASK_27 | MASK_11); |
| |
| /* turn on video-dma1 */ |
| WRITE_RPS0(CMD_WR_REG_MASK | (MC1/4)); |
| WRITE_RPS0(MASK_06 | MASK_22); /* => mask */ |
| WRITE_RPS0(MASK_06 | MASK_22); /* => values */ |
| if( 0 != planar ) { |
| /* turn on video-dma2 */ |
| WRITE_RPS0(CMD_WR_REG_MASK | (MC1/4)); |
| WRITE_RPS0(MASK_05 | MASK_21); /* => mask */ |
| WRITE_RPS0(MASK_05 | MASK_21); /* => values */ |
| |
| /* turn on video-dma3 */ |
| WRITE_RPS0(CMD_WR_REG_MASK | (MC1/4)); |
| WRITE_RPS0(MASK_04 | MASK_20); /* => mask */ |
| WRITE_RPS0(MASK_04 | MASK_20); /* => values */ |
| } |
| |
| /* wait for o_fid_a/b / e_fid_a/b toggle */ |
| if ( vv->last_field == V4L2_FIELD_INTERLACED ) { |
| WRITE_RPS0(CMD_PAUSE | o_wait); |
| WRITE_RPS0(CMD_PAUSE | e_wait); |
| } else if ( vv->last_field == V4L2_FIELD_TOP ) { |
| WRITE_RPS0(CMD_PAUSE | (vv->current_hps_sync == SAA7146_HPS_SYNC_PORT_A ? MASK_10 : MASK_09)); |
| WRITE_RPS0(CMD_PAUSE | o_wait); |
| } else if ( vv->last_field == V4L2_FIELD_BOTTOM ) { |
| WRITE_RPS0(CMD_PAUSE | (vv->current_hps_sync == SAA7146_HPS_SYNC_PORT_A ? MASK_10 : MASK_09)); |
| WRITE_RPS0(CMD_PAUSE | e_wait); |
| } |
| |
| /* turn off video-dma1 */ |
| WRITE_RPS0(CMD_WR_REG_MASK | (MC1/4)); |
| WRITE_RPS0(MASK_22 | MASK_06); /* => mask */ |
| WRITE_RPS0(MASK_22); /* => values */ |
| if( 0 != planar ) { |
| /* turn off video-dma2 */ |
| WRITE_RPS0(CMD_WR_REG_MASK | (MC1/4)); |
| WRITE_RPS0(MASK_05 | MASK_21); /* => mask */ |
| WRITE_RPS0(MASK_21); /* => values */ |
| |
| /* turn off video-dma3 */ |
| WRITE_RPS0(CMD_WR_REG_MASK | (MC1/4)); |
| WRITE_RPS0(MASK_04 | MASK_20); /* => mask */ |
| WRITE_RPS0(MASK_20); /* => values */ |
| } |
| |
| /* generate interrupt */ |
| WRITE_RPS0(CMD_INTERRUPT); |
| |
| /* stop */ |
| WRITE_RPS0(CMD_STOP); |
| } |
| |
| void saa7146_set_capture(struct saa7146_dev *dev, struct saa7146_buf *buf, struct saa7146_buf *next) |
| { |
| struct saa7146_format *sfmt = saa7146_format_by_fourcc(dev,buf->fmt->pixelformat); |
| struct saa7146_vv *vv = dev->vv_data; |
| u32 vdma1_prot_addr; |
| |
| DEB_CAP("buf:%p, next:%p\n", buf, next); |
| |
| vdma1_prot_addr = saa7146_read(dev, PROT_ADDR1); |
| if( 0 == vdma1_prot_addr ) { |
| /* clear out beginning of streaming bit (rps register 0)*/ |
| DEB_CAP("forcing sync to new frame\n"); |
| saa7146_write(dev, MC2, MASK_27 ); |
| } |
| |
| saa7146_set_window(dev, buf->fmt->width, buf->fmt->height, buf->fmt->field); |
| saa7146_set_output_format(dev, sfmt->trans); |
| saa7146_disable_clipping(dev); |
| |
| if ( vv->last_field == V4L2_FIELD_INTERLACED ) { |
| } else if ( vv->last_field == V4L2_FIELD_TOP ) { |
| vv->last_field = V4L2_FIELD_BOTTOM; |
| } else if ( vv->last_field == V4L2_FIELD_BOTTOM ) { |
| vv->last_field = V4L2_FIELD_TOP; |
| } |
| |
| if( 0 != IS_PLANAR(sfmt->trans)) { |
| calculate_video_dma_grab_planar(dev, buf); |
| program_capture_engine(dev,1); |
| } else { |
| calculate_video_dma_grab_packed(dev, buf); |
| program_capture_engine(dev,0); |
| } |
| |
| /* |
| printk("vdma%d.base_even: 0x%08x\n", 1,saa7146_read(dev,BASE_EVEN1)); |
| printk("vdma%d.base_odd: 0x%08x\n", 1,saa7146_read(dev,BASE_ODD1)); |
| printk("vdma%d.prot_addr: 0x%08x\n", 1,saa7146_read(dev,PROT_ADDR1)); |
| printk("vdma%d.base_page: 0x%08x\n", 1,saa7146_read(dev,BASE_PAGE1)); |
| printk("vdma%d.pitch: 0x%08x\n", 1,saa7146_read(dev,PITCH1)); |
| printk("vdma%d.num_line_byte: 0x%08x\n", 1,saa7146_read(dev,NUM_LINE_BYTE1)); |
| printk("vdma%d => vptr : 0x%08x\n", 1,saa7146_read(dev,PCI_VDP1)); |
| */ |
| |
| /* write the address of the rps-program */ |
| saa7146_write(dev, RPS_ADDR0, dev->d_rps0.dma_handle); |
| |
| /* turn on rps */ |
| saa7146_write(dev, MC1, (MASK_12 | MASK_28)); |
| } |