drivers/staging/rtl8188eu/include/pwrseq.h - kernel/quantenna - Git at Google


 /******************************************************************************
  *
  * Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of version 2 of the GNU General Public License as
  * published by the Free Software Foundation.
  *
  * This program is distributed in the hope that it will be useful, but WITHOUT
  * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
  * more details.
  *
  ******************************************************************************/

 #ifndef __HAL8188EPWRSEQ_H__
 #define __HAL8188EPWRSEQ_H__

 #include "pwrseqcmd.h"

 /*
 	Check document WM-20110607-Paul-RTL8188E_Power_Architecture-R02.vsd
 	There are 6 HW Power States:
 	0: POFF--Power Off
 	1: PDN--Power Down
 	2: CARDEMU--Card Emulation
 	3: ACT--Active Mode
 	4: LPS--Low Power State
 	5: SUS--Suspend

 	The transision from different states are defined below
 	TRANS_CARDEMU_TO_ACT
 	TRANS_ACT_TO_CARDEMU
 	TRANS_CARDEMU_TO_SUS
 	TRANS_SUS_TO_CARDEMU
 	TRANS_CARDEMU_TO_PDN
 	TRANS_ACT_TO_LPS
 	TRANS_LPS_TO_ACT

 	TRANS_END

     PWR SEQ Version: rtl8188E_PwrSeq_V09.h
 */
 #define RTL8188E_TRANS_CARDEMU_TO_ACT_STEPS	10
 #define RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS	10
 #define RTL8188E_TRANS_CARDEMU_TO_SUS_STEPS	10
 #define RTL8188E_TRANS_SUS_TO_CARDEMU_STEPS	10
 #define RTL8188E_TRANS_CARDEMU_TO_PDN_STEPS	10
 #define RTL8188E_TRANS_PDN_TO_CARDEMU_STEPS	10
 #define RTL8188E_TRANS_ACT_TO_LPS_STEPS		15
 #define RTL8188E_TRANS_LPS_TO_ACT_STEPS		15
 #define RTL8188E_TRANS_END_STEPS		1


 #define RTL8188E_TRANS_CARDEMU_TO_ACT					\
 	/* format
 	 * { offset, cut_msk, cmd, msk, value
 	 * },
 	 * comment here
 	 */								\
 	{0x0006, PWR_CUT_ALL_MSK, PWR_CMD_POLLING, BIT(1), BIT(1)}, \
 	/* wait till 0x04[17] = 1    power ready*/	\
 	{0x0002, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(0) | BIT(1), 0}, \
 	/* 0x02[1:0] = 0	reset BB*/				\
 	{0x0026, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(7), BIT(7)}, \
 	/*0x24[23] = 2b'01 schmit trigger */				\
 	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(7), 0}, \
 	/* 0x04[15] = 0 disable HWPDN (control by DRV)*/		\
 	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(4) | BIT(3), 0}, \
 	/*0x04[12:11] = 2b'00 disable WL suspend*/			\
 	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(0), BIT(0)}, \
 	/*0x04[8] = 1 polling until return 0*/				\
 	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_POLLING, BIT(0), 0}, \
 	/*wait till 0x04[8] = 0*/					\
 	{0x0023, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(4), 0}, \
 	/*LDO normal mode*/

 #define RTL8188E_TRANS_ACT_TO_CARDEMU					\
 	/* format
 	 * { offset, cut_msk, cmd, msk, value
 	 * },
 	 * comments here
 	 */								\
 	{0x001F, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, 0xFF, 0}, \
 	/*0x1F[7:0] = 0 turn off RF*/					\
 	{0x0023, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(4), BIT(4)}, \
 	/*LDO Sleep mode*/						\
 	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(1), BIT(1)}, \
 	/*0x04[9] = 1 turn off MAC by HW state machine*/		\
 	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_POLLING, BIT(1), 0}, \
 	/*wait till 0x04[9] = 0 polling until return 0 to disable*/

 #define RTL8188E_TRANS_CARDEMU_TO_SUS					\
 	/* format
 	 * { offset, cut_msk, cmd, msk,
 	 * value },
 	 * comments here
 	 */								\
 	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(3) | BIT(4), BIT(3)}, \
 	/* 0x04[12:11] = 2b'01enable WL suspend */			\
 	{0x0007, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, 0xFF, BIT(7)}, \
 	/* 0x04[31:30] = 2b'10 enable enable bandgap mbias in suspend */\
 	{0x0041, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(4), 0}, \
 	/*Clear SIC_EN register 0x40[12] = 1'b0 */			\
 	{0xfe10, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(4), BIT(4)}, \
 	/*Set USB suspend enable local register  0xfe10[4]=1 */

 #define RTL8188E_TRANS_SUS_TO_CARDEMU					\
 	/* format
 	 * { offset, cut_msk, cmd, msk,
 	 * value },
 	 * comments here
 	 */								\
 	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(3) | BIT(4), 0}, \
 	/*0x04[12:11] = 2b'01enable WL suspend*/

 #define RTL8188E_TRANS_CARDEMU_TO_CARDDIS				\
 	/* format
 	 * { offset, cut_msk, cmd, msk,
 	 * value },
 	 * comments here
 	 */								\
 	{0x0026, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(7), BIT(7)}, \
 	/*0x24[23] = 2b'01 schmit trigger */				\
 	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(3) | BIT(4), BIT(3)}, \
 	/*0x04[12:11] = 2b'01 enable WL suspend*/			\
 	{0x0007, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, 0xFF, 0}, \
 	/* 0x04[31:30] = 2b'10 enable enable bandgap mbias in suspend */\
 	{0x0041, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(4), 0}, \
 	/*Clear SIC_EN register 0x40[12] = 1'b0 */			\
 	{0xfe10, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(4), BIT(4)}, \
 	/*Set USB suspend enable local register  0xfe10[4]=1 */

 #define RTL8188E_TRANS_CARDDIS_TO_CARDEMU				\
 	/* format
 	 * { offset, cut_msk, cmd, msk,
 	 * value },
 	 * comments here
 	 */								\
 	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(3) | BIT(4), 0}, \
 	/*0x04[12:11] = 2b'01enable WL suspend*/

 #define RTL8188E_TRANS_CARDEMU_TO_PDN					\
 	/* format
 	 * { offset, cut_msk, cmd, msk,
 	 * value },
 	 * comments here
 	 */								\
 	{0x0006, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(0), 0}, \
 	/* 0x04[16] = 0*/						\
 	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(7), BIT(7)}, \
 	/* 0x04[15] = 1*/

 #define RTL8188E_TRANS_PDN_TO_CARDEMU					\
 	/* format
 	 * { offset, cut_msk, cmd, msk,
 	 * value },
 	 * comments here
 	 */								\
 	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(7), 0}, \
 	/* 0x04[15] = 0*/

 /* This is used by driver for LPSRadioOff Procedure, not for FW LPS Step */
 #define RTL8188E_TRANS_ACT_TO_LPS					\
 	/* format
 	 * { offset, cut_msk, cmd, msk,
 	 * value },
 	 * comments here
 	 */								\
 	{0x0522, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, 0xFF, 0x7F},/*Tx Pause*/ \
 	{0x05F8, PWR_CUT_ALL_MSK, PWR_CMD_POLLING, 0xFF, 0}, \
 	/*Should be zero if no packet is transmitting*/			\
 	{0x05F9, PWR_CUT_ALL_MSK, PWR_CMD_POLLING, 0xFF, 0}, \
 	/*Should be zero if no packet is transmitting*/			\
 	{0x05FA, PWR_CUT_ALL_MSK, PWR_CMD_POLLING, 0xFF, 0}, \
 	/*Should be zero if no packet is transmitting*/			\
 	{0x05FB, PWR_CUT_ALL_MSK, PWR_CMD_POLLING, 0xFF, 0}, \
 	/*Should be zero if no packet is transmitting*/			\
 	{0x0002, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(0), 0}, \
 	/*CCK and OFDM are disabled,and clock are gated*/		\
 	{0x0002, PWR_CUT_ALL_MSK, PWR_CMD_DELAY, 0,	PWRSEQ_DELAY_US}, \
 	/*Delay 1us*/ \
 	{0x0100, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, 0xFF, 0x3F}, \
 	/*Reset MAC TRX*/ \
 	{0x0101, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(1), 0}, \
 	/*check if removed later*/\
 	{0x0553, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(5), BIT(5)}, \
 	/*Respond TxOK to scheduler*/


 #define RTL8188E_TRANS_LPS_TO_ACT					\
 	/* format
 	 * { offset, cut_msk, cmd, msk,
 	 * value },
 	 * comments here
 	 */								\
 	{0xFE58, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, 0xFF, 0x84}, \
 	/*USB RPWM*/	\
 	{0x0002, PWR_CUT_ALL_MSK, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, \
 	/*Delay*/	\
 	{0x0008, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(4), 0}, \
 	/* 0x08[4] = 0 switch TSF to 40M */				\
 	{0x0109, PWR_CUT_ALL_MSK, PWR_CMD_POLLING, BIT(7), 0}, \
 	/* Polling 0x109[7]=0  TSF in 40M */				\
 	{0x0029, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(6) | BIT(7), 0}, \
 	/* 0x29[7:6] = 2b'00  enable BB clock */			\
 	{0x0101, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(1), BIT(1)}, \
 	/* 0x101[1] = 1 */						\
 	{0x0100, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, 0xFF, 0xFF}, \
 	/* 0x100[7:0] = 0xFF enable WMAC TRX */				\
 	{0x0002, PWR_CUT_ALL_MSK, \
 	PWR_CMD_WRITE, BIT(1) | BIT(0), BIT(1) | BIT(0)}, \
 	/* 0x02[1:0] = 2b'11 enable BB macro */				\
 	{0x0522, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, 0xFF, 0}, /*.	0x522 = 0*/

 #define RTL8188E_TRANS_END						\
 	/* format
 	 * { offset, cut_msk, cmd, msk,
 	 * value },
 	 * comments here
 	 */								\
 	{0xFFFF, PWR_CUT_ALL_MSK, PWR_CMD_END, 0, 0},


 extern struct wl_pwr_cfg rtl8188E_power_on_flow
 		[RTL8188E_TRANS_CARDEMU_TO_ACT_STEPS + RTL8188E_TRANS_END_STEPS];
 extern struct wl_pwr_cfg rtl8188E_radio_off_flow
 		[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188E_TRANS_END_STEPS];
 extern struct wl_pwr_cfg rtl8188E_card_disable_flow
 		[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS +
 		RTL8188E_TRANS_CARDEMU_TO_PDN_STEPS +
 		RTL8188E_TRANS_END_STEPS];
 extern struct wl_pwr_cfg rtl8188E_card_enable_flow
 		[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS +
 		RTL8188E_TRANS_CARDEMU_TO_PDN_STEPS +
 		RTL8188E_TRANS_END_STEPS];
 extern struct wl_pwr_cfg rtl8188E_suspend_flow[
 		RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS +
 		RTL8188E_TRANS_CARDEMU_TO_SUS_STEPS +
 		RTL8188E_TRANS_END_STEPS];
 extern struct wl_pwr_cfg rtl8188E_resume_flow
 		[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS +
 		RTL8188E_TRANS_CARDEMU_TO_SUS_STEPS +
 		RTL8188E_TRANS_END_STEPS];
 extern struct wl_pwr_cfg rtl8188E_hwpdn_flow
 		[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS +
 		RTL8188E_TRANS_CARDEMU_TO_PDN_STEPS + RTL8188E_TRANS_END_STEPS];
 extern struct wl_pwr_cfg rtl8188E_enter_lps_flow
 		[RTL8188E_TRANS_ACT_TO_LPS_STEPS + RTL8188E_TRANS_END_STEPS];
 extern struct wl_pwr_cfg rtl8188E_leave_lps_flow
 		[RTL8188E_TRANS_LPS_TO_ACT_STEPS + RTL8188E_TRANS_END_STEPS];

 #endif /* __HAL8188EPWRSEQ_H__ */

	/******************************************************************************
	*
	* Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved.
	*
	* This program is free software; you can redistribute it and/or modify it
	* under the terms of version 2 of the GNU General Public License as
	* published by the Free Software Foundation.
	*
	* This program is distributed in the hope that it will be useful, but WITHOUT
	* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
	* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
	* more details.
	*
	******************************************************************************/

	#ifndef __HAL8188EPWRSEQ_H__
	#define __HAL8188EPWRSEQ_H__

	#include "pwrseqcmd.h"

	/*
	Check document WM-20110607-Paul-RTL8188E_Power_Architecture-R02.vsd
	There are 6 HW Power States:
	0: POFF--Power Off
	1: PDN--Power Down
	2: CARDEMU--Card Emulation
	3: ACT--Active Mode
	4: LPS--Low Power State
	5: SUS--Suspend

	The transision from different states are defined below
	TRANS_CARDEMU_TO_ACT
	TRANS_ACT_TO_CARDEMU
	TRANS_CARDEMU_TO_SUS
	TRANS_SUS_TO_CARDEMU
	TRANS_CARDEMU_TO_PDN
	TRANS_ACT_TO_LPS
	TRANS_LPS_TO_ACT

	TRANS_END

	PWR SEQ Version: rtl8188E_PwrSeq_V09.h
	*/
	#define RTL8188E_TRANS_CARDEMU_TO_ACT_STEPS 10
	#define RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS 10
	#define RTL8188E_TRANS_CARDEMU_TO_SUS_STEPS 10
	#define RTL8188E_TRANS_SUS_TO_CARDEMU_STEPS 10
	#define RTL8188E_TRANS_CARDEMU_TO_PDN_STEPS 10
	#define RTL8188E_TRANS_PDN_TO_CARDEMU_STEPS 10
	#define RTL8188E_TRANS_ACT_TO_LPS_STEPS 15
	#define RTL8188E_TRANS_LPS_TO_ACT_STEPS 15
	#define RTL8188E_TRANS_END_STEPS 1


	#define RTL8188E_TRANS_CARDEMU_TO_ACT \
	/* format
	* { offset, cut_msk, cmd, msk, value
	* },
	* comment here
	*/ \
	{0x0006, PWR_CUT_ALL_MSK, PWR_CMD_POLLING, BIT(1), BIT(1)}, \
	/* wait till 0x04[17] = 1 power ready*/ \
	{0x0002, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(0) \| BIT(1), 0}, \
	/* 0x02[1:0] = 0 reset BB*/ \
	{0x0026, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(7), BIT(7)}, \
	/0x24[23] = 2b'01 schmit trigger / \
	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(7), 0}, \
	/* 0x04[15] = 0 disable HWPDN (control by DRV)*/ \
	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(4) \| BIT(3), 0}, \
	/0x04[12:11] = 2b'00 disable WL suspend/ \
	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(0), BIT(0)}, \
	/0x04[8] = 1 polling until return 0/ \
	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_POLLING, BIT(0), 0}, \
	/wait till 0x04[8] = 0/ \
	{0x0023, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(4), 0}, \
	/LDO normal mode/

	#define RTL8188E_TRANS_ACT_TO_CARDEMU \
	/* format
	* { offset, cut_msk, cmd, msk, value
	* },
	* comments here
	*/ \
	{0x001F, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, 0xFF, 0}, \
	/0x1F[7:0] = 0 turn off RF/ \
	{0x0023, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(4), BIT(4)}, \
	/LDO Sleep mode/ \
	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(1), BIT(1)}, \
	/0x04[9] = 1 turn off MAC by HW state machine/ \
	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_POLLING, BIT(1), 0}, \
	/wait till 0x04[9] = 0 polling until return 0 to disable/

	#define RTL8188E_TRANS_CARDEMU_TO_SUS \
	/* format
	* { offset, cut_msk, cmd, msk,
	* value },
	* comments here
	*/ \
	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(3) \| BIT(4), BIT(3)}, \
	/* 0x04[12:11] = 2b'01enable WL suspend */ \
	{0x0007, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, 0xFF, BIT(7)}, \
	/* 0x04[31:30] = 2b'10 enable enable bandgap mbias in suspend */\
	{0x0041, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(4), 0}, \
	/Clear SIC_EN register 0x40[12] = 1'b0 / \
	{0xfe10, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(4), BIT(4)}, \
	/Set USB suspend enable local register 0xfe10[4]=1 /

	#define RTL8188E_TRANS_SUS_TO_CARDEMU \
	/* format
	* { offset, cut_msk, cmd, msk,
	* value },
	* comments here
	*/ \
	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(3) \| BIT(4), 0}, \
	/0x04[12:11] = 2b'01enable WL suspend/

	#define RTL8188E_TRANS_CARDEMU_TO_CARDDIS \
	/* format
	* { offset, cut_msk, cmd, msk,
	* value },
	* comments here
	*/ \
	{0x0026, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(7), BIT(7)}, \
	/0x24[23] = 2b'01 schmit trigger / \
	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(3) \| BIT(4), BIT(3)}, \
	/0x04[12:11] = 2b'01 enable WL suspend/ \
	{0x0007, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, 0xFF, 0}, \
	/* 0x04[31:30] = 2b'10 enable enable bandgap mbias in suspend */\
	{0x0041, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(4), 0}, \
	/Clear SIC_EN register 0x40[12] = 1'b0 / \
	{0xfe10, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(4), BIT(4)}, \
	/Set USB suspend enable local register 0xfe10[4]=1 /

	#define RTL8188E_TRANS_CARDDIS_TO_CARDEMU \
	/* format
	* { offset, cut_msk, cmd, msk,
	* value },
	* comments here
	*/ \
	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(3) \| BIT(4), 0}, \
	/0x04[12:11] = 2b'01enable WL suspend/

	#define RTL8188E_TRANS_CARDEMU_TO_PDN \
	/* format
	* { offset, cut_msk, cmd, msk,
	* value },
	* comments here
	*/ \
	{0x0006, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(0), 0}, \
	/* 0x04[16] = 0*/ \
	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(7), BIT(7)}, \
	/* 0x04[15] = 1*/

	#define RTL8188E_TRANS_PDN_TO_CARDEMU \
	/* format
	* { offset, cut_msk, cmd, msk,
	* value },
	* comments here
	*/ \
	{0x0005, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(7), 0}, \
	/* 0x04[15] = 0*/

	/* This is used by driver for LPSRadioOff Procedure, not for FW LPS Step */
	#define RTL8188E_TRANS_ACT_TO_LPS \
	/* format
	* { offset, cut_msk, cmd, msk,
	* value },
	* comments here
	*/ \
	{0x0522, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, 0xFF, 0x7F},/Tx Pause/ \
	{0x05F8, PWR_CUT_ALL_MSK, PWR_CMD_POLLING, 0xFF, 0}, \
	/Should be zero if no packet is transmitting/ \
	{0x05F9, PWR_CUT_ALL_MSK, PWR_CMD_POLLING, 0xFF, 0}, \
	/Should be zero if no packet is transmitting/ \
	{0x05FA, PWR_CUT_ALL_MSK, PWR_CMD_POLLING, 0xFF, 0}, \
	/Should be zero if no packet is transmitting/ \
	{0x05FB, PWR_CUT_ALL_MSK, PWR_CMD_POLLING, 0xFF, 0}, \
	/Should be zero if no packet is transmitting/ \
	{0x0002, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(0), 0}, \
	/CCK and OFDM are disabled,and clock are gated/ \
	{0x0002, PWR_CUT_ALL_MSK, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US}, \
	/Delay 1us/ \
	{0x0100, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, 0xFF, 0x3F}, \
	/Reset MAC TRX/ \
	{0x0101, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(1), 0}, \
	/check if removed later/\
	{0x0553, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(5), BIT(5)}, \
	/Respond TxOK to scheduler/


	#define RTL8188E_TRANS_LPS_TO_ACT \
	/* format
	* { offset, cut_msk, cmd, msk,
	* value },
	* comments here
	*/ \
	{0xFE58, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, 0xFF, 0x84}, \
	/USB RPWM/ \
	{0x0002, PWR_CUT_ALL_MSK, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, \
	/Delay/ \
	{0x0008, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(4), 0}, \
	/* 0x08[4] = 0 switch TSF to 40M */ \
	{0x0109, PWR_CUT_ALL_MSK, PWR_CMD_POLLING, BIT(7), 0}, \
	/* Polling 0x109[7]=0 TSF in 40M */ \
	{0x0029, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(6) \| BIT(7), 0}, \
	/* 0x29[7:6] = 2b'00 enable BB clock */ \
	{0x0101, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, BIT(1), BIT(1)}, \
	/* 0x101[1] = 1 */ \
	{0x0100, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, 0xFF, 0xFF}, \
	/* 0x100[7:0] = 0xFF enable WMAC TRX */ \
	{0x0002, PWR_CUT_ALL_MSK, \
	PWR_CMD_WRITE, BIT(1) \| BIT(0), BIT(1) \| BIT(0)}, \
	/* 0x02[1:0] = 2b'11 enable BB macro */ \
	{0x0522, PWR_CUT_ALL_MSK, PWR_CMD_WRITE, 0xFF, 0}, /. 0x522 = 0/

	#define RTL8188E_TRANS_END \
	/* format
	* { offset, cut_msk, cmd, msk,
	* value },
	* comments here
	*/ \
	{0xFFFF, PWR_CUT_ALL_MSK, PWR_CMD_END, 0, 0},


	extern struct wl_pwr_cfg rtl8188E_power_on_flow
	[RTL8188E_TRANS_CARDEMU_TO_ACT_STEPS + RTL8188E_TRANS_END_STEPS];
	extern struct wl_pwr_cfg rtl8188E_radio_off_flow
	[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188E_TRANS_END_STEPS];
	extern struct wl_pwr_cfg rtl8188E_card_disable_flow
	[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS +
	RTL8188E_TRANS_CARDEMU_TO_PDN_STEPS +
	RTL8188E_TRANS_END_STEPS];
	extern struct wl_pwr_cfg rtl8188E_card_enable_flow
	[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS +
	RTL8188E_TRANS_CARDEMU_TO_PDN_STEPS +
	RTL8188E_TRANS_END_STEPS];
	extern struct wl_pwr_cfg rtl8188E_suspend_flow[
	RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS +
	RTL8188E_TRANS_CARDEMU_TO_SUS_STEPS +
	RTL8188E_TRANS_END_STEPS];
	extern struct wl_pwr_cfg rtl8188E_resume_flow
	[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS +
	RTL8188E_TRANS_CARDEMU_TO_SUS_STEPS +
	RTL8188E_TRANS_END_STEPS];
	extern struct wl_pwr_cfg rtl8188E_hwpdn_flow
	[RTL8188E_TRANS_ACT_TO_CARDEMU_STEPS +
	RTL8188E_TRANS_CARDEMU_TO_PDN_STEPS + RTL8188E_TRANS_END_STEPS];
	extern struct wl_pwr_cfg rtl8188E_enter_lps_flow
	[RTL8188E_TRANS_ACT_TO_LPS_STEPS + RTL8188E_TRANS_END_STEPS];
	extern struct wl_pwr_cfg rtl8188E_leave_lps_flow
	[RTL8188E_TRANS_LPS_TO_ACT_STEPS + RTL8188E_TRANS_END_STEPS];

	#endif /* __HAL8188EPWRSEQ_H__ */