| What: /sys/bus/iio/devices/device[n]/in_illuminance0[_input|_raw] |
| KernelVersion: 2.6.35 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| This should return the calculated lux from the light sensor. If |
| it comes back in SI units, it should also include _input else it |
| should include _raw to signify it is not in SI units. |
| |
| What: /sys/.../device[n]/proximity_on_chip_ambient_infrared_suppression |
| KernelVersion: 2.6.37 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| Hardware dependent mode for an ALS device to calculate the value |
| in proximity mode. When this is enabled, then the device should |
| use a infrared sensor reading to remove infrared noise from the |
| proximity reading. If this is not enabled, the driver can still |
| do this calculation manually by reading the infrared sensor |
| value and doing the negation in sw. |
| |
| What: /sys/bus/iio/devices/device[n]/in_proximity[_input|_raw] |
| KernelVersion: 2.6.37 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| This property is supported by proximity sensors and should be |
| used to return the value of a reading by the sensor. If this |
| value is returned in SI units, it should also include _input |
| but if it is not, then it should include _raw. |
| |
| What: /sys/bus/iio/devices/device[n]/intensity_infrared[_input|_raw] |
| KernelVersion: 2.6.37 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| This property is supported by sensors that have an infrared |
| sensing mode. This value should be the output from a reading |
| and if expressed in SI units, should include _input. If this |
| value is not in SI units, then it should include _raw. |
| |
| What: /sys/bus/iio/devices/device[n]/in_illuminance0_target |
| KernelVersion: 2.6.37 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| This property gets/sets the last known external |
| lux measurement used in/for calibration. |
| |
| What: /sys/bus/iio/devices/device[n]/in_illuminance0_integration_time |
| KernelVersion: 2.6.37 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| This property gets/sets the sensors ADC analog integration time. |
| |
| What: /sys/bus/iio/devices/device[n]/in_illuminance0_lux_table |
| KernelVersion: 2.6.37 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| This property gets/sets the table of coefficients |
| used in calculating illuminance in lux. |
| |
| What: /sys/bus/iio/devices/device[n]/in_intensity_clear[_input|_raw] |
| What: /sys/bus/iio/devices/device[n]/in_intensity_red[_input|_raw] |
| What: /sys/bus/iio/devices/device[n]/in_intensity_green[_input|_raw] |
| What: /sys/bus/iio/devices/device[n]/in_intensity_blue[_input|_raw] |
| KernelVersion: 3.6.0 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| This property is supported by sensors that have a RGBC |
| sensing mode. This value should be the output from a reading |
| and if expressed in SI units, should include _input. If this |
| value is not in SI units (irradiance, uW/mm^2), then it should |
| include _raw. |
| |
| What: /sys/bus/iio/devices/device[n]/in_cct0[_input|_raw] |
| KernelVersion: 3.6.0 |
| Contact: linux-iio@vger.kernel.org |
| Description: |
| This should return the correlated color temperature from the |
| light sensor. If it comes back in SI units, it should also |
| include _input else it should include _raw to signify it is not |
| in SI units. |
| |
