blob: d74e631e10da1eb35252c97660d7044e1c502941 [file] [log] [blame]
Qualcomm PMIC Multi-Purpose Pin (MPP) block
This binding describes the MPP block(s) found in the 8xxx series
of PMIC's from Qualcomm.
- compatible:
Usage: required
Value type: <string>
Definition: Should contain one of:
"qcom,pm8018-mpp",
"qcom,pm8038-mpp",
"qcom,pm8821-mpp",
"qcom,pm8841-mpp",
"qcom,pm8916-mpp",
"qcom,pm8917-mpp",
"qcom,pm8921-mpp",
"qcom,pm8941-mpp",
"qcom,pm8994-mpp",
"qcom,pma8084-mpp",
- reg:
Usage: required
Value type: <prop-encoded-array>
Definition: Register base of the MPP block and length.
- interrupts:
Usage: required
Value type: <prop-encoded-array>
Definition: Must contain an array of encoded interrupt specifiers for
each available MPP
- gpio-controller:
Usage: required
Value type: <none>
Definition: Mark the device node as a GPIO controller
- #gpio-cells:
Usage: required
Value type: <u32>
Definition: Must be 2;
the first cell will be used to define MPP number and the
second denotes the flags for this MPP
Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
a general description of GPIO and interrupt bindings.
Please refer to pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices, including the meaning of the
phrase "pin configuration node".
The pin configuration nodes act as a container for an arbitrary number of
subnodes. Each of these subnodes represents some desired configuration for a
pin or a list of pins. This configuration can include the
mux function to select on those pin(s), and various pin configuration
parameters, as listed below.
SUBNODES:
The name of each subnode is not important; all subnodes should be enumerated
and processed purely based on their content.
Each subnode only affects those parameters that are explicitly listed. In
other words, a subnode that lists a mux function but no pin configuration
parameters implies no information about any pin configuration parameters.
Similarly, a pin subnode that describes a pullup parameter implies no
information about e.g. the mux function.
The following generic properties as defined in pinctrl-bindings.txt are valid
to specify in a pin configuration subnode:
- pins:
Usage: required
Value type: <string-array>
Definition: List of MPP pins affected by the properties specified in
this subnode. Valid pins are:
mpp1-mpp4 for pm8841
mpp1-mpp4 for pm8916
mpp1-mpp8 for pm8941
mpp1-mpp4 for pma8084
- function:
Usage: required
Value type: <string>
Definition: Specify the alternative function to be configured for the
specified pins. Valid values are:
"digital",
"analog",
"sink"
- bias-disable:
Usage: optional
Value type: <none>
Definition: The specified pins should be configured as no pull.
- bias-pull-up:
Usage: optional
Value type: <u32>
Definition: The specified pins should be configured as pull up.
Valid values are 600, 10000 and 30000 in bidirectional mode
only, i.e. when operating in qcom,analog-mode and input and
outputs are enabled. The hardware ignores the configuration
when operating in other modes.
- bias-high-impedance:
Usage: optional
Value type: <none>
Definition: The specified pins will put in high-Z mode and disabled.
- input-enable:
Usage: optional
Value type: <none>
Definition: The specified pins are put in input mode, i.e. their input
buffer is enabled
- output-high:
Usage: optional
Value type: <none>
Definition: The specified pins are configured in output mode, driven
high.
- output-low:
Usage: optional
Value type: <none>
Definition: The specified pins are configured in output mode, driven
low.
- power-source:
Usage: optional
Value type: <u32>
Definition: Selects the power source for the specified pins. Valid power
sources are defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
- qcom,analog-level:
Usage: optional
Value type: <u32>
Definition: Selects the source for analog output. Valued values are
defined in <dt-binding/pinctrl/qcom,pmic-mpp.h>
PMIC_MPP_AOUT_LVL_*
- qcom,dtest:
Usage: optional
Value type: <u32>
Definition: Selects which dtest rail to be routed in the various functions.
Valid values are 1-4
- qcom,amux-route:
Usage: optional
Value type: <u32>
Definition: Selects the source for analog input. Valid values are
defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
PMIC_MPP_AMUX_ROUTE_CH5, PMIC_MPP_AMUX_ROUTE_CH6...
- qcom,paired:
Usage: optional
Value type: <none>
Definition: Indicates that the pin should be operating in paired mode.
Example:
mpps@a000 {
compatible = "qcom,pm8841-mpp";
reg = <0xa000>;
gpio-controller;
#gpio-cells = <2>;
interrupts = <4 0xa0 0 0>, <4 0xa1 0 0>, <4 0xa2 0 0>, <4 0xa3 0 0>;
pinctrl-names = "default";
pinctrl-0 = <&pm8841_default>;
pm8841_default: default {
gpio {
pins = "mpp1", "mpp2", "mpp3", "mpp4";
function = "digital";
input-enable;
power-source = <PM8841_MPP_S3>;
};
};
};