drivers/usb/serial/keyspan_usa90msg.h - kernel/quantenna - Git at Google

 /*
 	usa90msg.h

 	Copyright (c) 1998-2003 InnoSys Incorporated.  All Rights Reserved
 	This file is available under a BSD-style copyright

 	Keyspan USB Async Message Formats for the USA19HS

 	Redistribution and use in source and binary forms, with or without
 	modification, are permitted provided that the following conditions are
 	met:

 	1. Redistributions of source code must retain this licence text
    	without modification, this list of conditions, and the following
    	disclaimer.  The following copyright notice must appear immediately at
    	the beginning of all source files:

         	Copyright (c) 1998-2003 InnoSys Incorporated.  All Rights Reserved

         	This file is available under a BSD-style copyright

 	2. The name of InnoSys Incorporated may not be used to endorse or promote
    	products derived from this software without specific prior written
    	permission.

 	THIS SOFTWARE IS PROVIDED BY INNOSYS CORP. ``AS IS'' AND ANY EXPRESS OR
 	IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
 	OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
 	NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
 	INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
 	(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
 	SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
 	CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 	LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
 	OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
 	SUCH DAMAGE.

 	Revisions:

 	2003feb14		add setTxMode/txMode  and cancelRxXoff to portControl
 	2003mar21		change name of PARITY_0/1 to add MARK/SPACE
 */

 #ifndef	__USA90MSG__
 #define	__USA90MSG__

 struct keyspan_usa90_portControlMessage
 {
 	/*
 		there are three types of "commands" sent in the control message:

 		1.	configuration changes which must be requested by setting
 			the corresponding "set" flag (and should only be requested
 			when necessary, to reduce overhead on the device):
 	*/

 	u8	setClocking,	// host requests baud rate be set
 		baudLo,			// host does baud divisor calculation
 		baudHi,			// host does baud divisor calculation

 		setLcr,			// host requests lcr be set
 		lcr,			// use PARITY, STOPBITS, DATABITS below

 		setRxMode,		// set receive mode
 		rxMode,			// RXMODE_DMA or RXMODE_BYHAND

 		setTxMode,		// set transmit mode
 		txMode,			// TXMODE_DMA or TXMODE_BYHAND

 		setTxFlowControl,	// host requests tx flow control be set
 		txFlowControl	,	// use TX_FLOW... bits below
 		setRxFlowControl,	// host requests rx flow control be set
 		rxFlowControl,	// use RX_FLOW... bits below
 		sendXoff,		// host requests XOFF transmitted immediately
 		sendXon,		// host requests XON char transmitted
 		xonChar,		// specified in current character format
 		xoffChar,		// specified in current character format

 		sendChar,		// host requests char transmitted immediately
 		txChar,			// character to send

 		setRts,			// host requests RTS output be set
 		rts,			// 1=on, 0=off
 		setDtr, 		// host requests DTR output be set
 		dtr;			// 1=on, 0=off


 	/*
 		2.	configuration data which is simply used as is
 			and must be specified correctly in every host message.
 	*/

 	u8	rxForwardingLength,  // forward when this number of chars available
 		rxForwardingTimeout, // (1-31 in ms)
 		txAckSetting;	   // 0=don't ack, 1=normal, 2-255 TBD...
 	/*
 		3.	Firmware states which cause actions if they change
 		and must be specified correctly in every host message.
 	*/

 	u8	portEnabled,	// 0=disabled, 1=enabled
 		txFlush,		// 0=normal, 1=toss outbound data
 		txBreak,		// 0=break off, 1=break on
 		loopbackMode;	// 0=no loopback, 1=loopback enabled

 	/*
 		4.	commands which are flags only; these are processed in order
 			(so that, e.g., if rxFlush and rxForward flags are set, the
 			port will have no data to forward); any non-zero value
 			is respected
 	*/

 	u8	rxFlush,		// toss inbound data
 		rxForward,		// forward all inbound data, NOW (as if fwdLen==1)
 		cancelRxXoff,	// cancel any receive XOFF state (_txXoff)
 		returnStatus;	// return current status NOW
 };

 // defines for bits in lcr
 #define		USA_DATABITS_5		0x00
 #define		USA_DATABITS_6		0x01
 #define		USA_DATABITS_7		0x02
 #define		USA_DATABITS_8		0x03
 #define		STOPBITS_5678_1		0x00	// 1 stop bit for all byte sizes
 #define		STOPBITS_5_1p5		0x04	// 1.5 stop bits for 5-bit byte
 #define		STOPBITS_678_2		0x04	// 2 stop bits for 6-8 bit byte
 #define		USA_PARITY_NONE		0x00
 #define		USA_PARITY_ODD		0x08
 #define		USA_PARITY_EVEN		0x18
 #define		PARITY_MARK_1  		0x28   	// force parity MARK
 #define		PARITY_SPACE_0 		0x38	// force parity SPACE

 #define		TXFLOW_CTS			0x04
 #define		TXFLOW_DSR			0x08
 #define		TXFLOW_XOFF			0x01
 #define		TXFLOW_XOFF_ANY		0x02
 #define		TXFLOW_XOFF_BITS	(TXFLOW_XOFF | TXFLOW_XOFF_ANY)

 #define		RXFLOW_XOFF			0x10
 #define		RXFLOW_RTS			0x20
 #define		RXFLOW_DTR			0x40
 #define		RXFLOW_DSR_SENSITIVITY	0x80

 #define		RXMODE_BYHAND		0x00
 #define		RXMODE_DMA			0x02

 #define		TXMODE_BYHAND		0x00
 #define		TXMODE_DMA			0x02


 // all things called "StatusMessage" are sent on the status endpoint

 struct keyspan_usa90_portStatusMessage
 {
 	u8	msr,			// reports the actual MSR register
 		cts,			// reports CTS pin
 		dcd,			// reports DCD pin
 		dsr,			// reports DSR pin
 		ri,				// reports RI pin
 		_txXoff,		// port is in XOFF state (we received XOFF)
 		rxBreak,		// reports break state
 		rxOverrun,		// count of overrun errors (since last reported)
 		rxParity,		// count of parity errors (since last reported)
 		rxFrame,		// count of frame errors (since last reported)
 		portState,		// PORTSTATE_xxx bits (useful for debugging)
 		messageAck,		// message acknowledgement
 		charAck,		// character acknowledgement
 		controlResponse;	// (value = returnStatus) a control message has been processed
 };

 // bits in RX data message when STAT byte is included

 #define	RXERROR_OVERRUN		0x02
 #define	RXERROR_PARITY		0x04
 #define	RXERROR_FRAMING		0x08
 #define	RXERROR_BREAK		0x10

 #define	PORTSTATE_ENABLED	0x80
 #define	PORTSTATE_TXFLUSH	0x01
 #define	PORTSTATE_TXBREAK	0x02
 #define	PORTSTATE_LOOPBACK 	0x04

 // MSR bits

 #define USA_MSR_dCTS	  		0x01		// CTS has changed since last report
 #define USA_MSR_dDSR	  		0x02
 #define USA_MSR_dRI			0x04
 #define USA_MSR_dDCD	  		0x08

 #define USA_MSR_CTS			0x10	  	// current state of CTS
 #define USA_MSR_DSR			0x20
 #define USA_USA_MSR_RI			0x40
 #define MSR_DCD				0x80

 // ie: the maximum length of an endpoint buffer
 #define		MAX_DATA_LEN			64

 #endif
	/*
	usa90msg.h

	Copyright (c) 1998-2003 InnoSys Incorporated. All Rights Reserved
	This file is available under a BSD-style copyright

	Keyspan USB Async Message Formats for the USA19HS

	Redistribution and use in source and binary forms, with or without
	modification, are permitted provided that the following conditions are
	met:

	1. Redistributions of source code must retain this licence text
	without modification, this list of conditions, and the following
	disclaimer. The following copyright notice must appear immediately at
	the beginning of all source files:

	Copyright (c) 1998-2003 InnoSys Incorporated. All Rights Reserved

	This file is available under a BSD-style copyright

	2. The name of InnoSys Incorporated may not be used to endorse or promote
	products derived from this software without specific prior written
	permission.

	THIS SOFTWARE IS PROVIDED BY INNOSYS CORP. ``AS IS'' AND ANY EXPRESS OR
	IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
	OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
	NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
	INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
	(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
	SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
	CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
	LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
	OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
	SUCH DAMAGE.

	Revisions:

	2003feb14 add setTxMode/txMode and cancelRxXoff to portControl
	2003mar21 change name of PARITY_0/1 to add MARK/SPACE
	*/

	#ifndef __USA90MSG__
	#define __USA90MSG__

	struct keyspan_usa90_portControlMessage
	{
	/*
	there are three types of "commands" sent in the control message:

	1. configuration changes which must be requested by setting
	the corresponding "set" flag (and should only be requested
	when necessary, to reduce overhead on the device):
	*/

	u8 setClocking, // host requests baud rate be set
	baudLo, // host does baud divisor calculation
	baudHi, // host does baud divisor calculation

	setLcr, // host requests lcr be set
	lcr, // use PARITY, STOPBITS, DATABITS below

	setRxMode, // set receive mode
	rxMode, // RXMODE_DMA or RXMODE_BYHAND

	setTxMode, // set transmit mode
	txMode, // TXMODE_DMA or TXMODE_BYHAND

	setTxFlowControl, // host requests tx flow control be set
	txFlowControl , // use TX_FLOW... bits below
	setRxFlowControl, // host requests rx flow control be set
	rxFlowControl, // use RX_FLOW... bits below
	sendXoff, // host requests XOFF transmitted immediately
	sendXon, // host requests XON char transmitted
	xonChar, // specified in current character format
	xoffChar, // specified in current character format

	sendChar, // host requests char transmitted immediately
	txChar, // character to send

	setRts, // host requests RTS output be set
	rts, // 1=on, 0=off
	setDtr, // host requests DTR output be set
	dtr; // 1=on, 0=off


	/*
	2. configuration data which is simply used as is
	and must be specified correctly in every host message.
	*/

	u8 rxForwardingLength, // forward when this number of chars available
	rxForwardingTimeout, // (1-31 in ms)
	txAckSetting; // 0=don't ack, 1=normal, 2-255 TBD...
	/*
	3. Firmware states which cause actions if they change
	and must be specified correctly in every host message.
	*/

	u8 portEnabled, // 0=disabled, 1=enabled
	txFlush, // 0=normal, 1=toss outbound data
	txBreak, // 0=break off, 1=break on
	loopbackMode; // 0=no loopback, 1=loopback enabled

	/*
	4. commands which are flags only; these are processed in order
	(so that, e.g., if rxFlush and rxForward flags are set, the
	port will have no data to forward); any non-zero value
	is respected
	*/

	u8 rxFlush, // toss inbound data
	rxForward, // forward all inbound data, NOW (as if fwdLen==1)
	cancelRxXoff, // cancel any receive XOFF state (_txXoff)
	returnStatus; // return current status NOW
	};

	// defines for bits in lcr
	#define USA_DATABITS_5 0x00
	#define USA_DATABITS_6 0x01
	#define USA_DATABITS_7 0x02
	#define USA_DATABITS_8 0x03
	#define STOPBITS_5678_1 0x00 // 1 stop bit for all byte sizes
	#define STOPBITS_5_1p5 0x04 // 1.5 stop bits for 5-bit byte
	#define STOPBITS_678_2 0x04 // 2 stop bits for 6-8 bit byte
	#define USA_PARITY_NONE 0x00
	#define USA_PARITY_ODD 0x08
	#define USA_PARITY_EVEN 0x18
	#define PARITY_MARK_1 0x28 // force parity MARK
	#define PARITY_SPACE_0 0x38 // force parity SPACE

	#define TXFLOW_CTS 0x04
	#define TXFLOW_DSR 0x08
	#define TXFLOW_XOFF 0x01
	#define TXFLOW_XOFF_ANY 0x02
	#define TXFLOW_XOFF_BITS (TXFLOW_XOFF \| TXFLOW_XOFF_ANY)

	#define RXFLOW_XOFF 0x10
	#define RXFLOW_RTS 0x20
	#define RXFLOW_DTR 0x40
	#define RXFLOW_DSR_SENSITIVITY 0x80

	#define RXMODE_BYHAND 0x00
	#define RXMODE_DMA 0x02

	#define TXMODE_BYHAND 0x00
	#define TXMODE_DMA 0x02


	// all things called "StatusMessage" are sent on the status endpoint

	struct keyspan_usa90_portStatusMessage
	{
	u8 msr, // reports the actual MSR register
	cts, // reports CTS pin
	dcd, // reports DCD pin
	dsr, // reports DSR pin
	ri, // reports RI pin
	_txXoff, // port is in XOFF state (we received XOFF)
	rxBreak, // reports break state
	rxOverrun, // count of overrun errors (since last reported)
	rxParity, // count of parity errors (since last reported)
	rxFrame, // count of frame errors (since last reported)
	portState, // PORTSTATE_xxx bits (useful for debugging)
	messageAck, // message acknowledgement
	charAck, // character acknowledgement
	controlResponse; // (value = returnStatus) a control message has been processed
	};

	// bits in RX data message when STAT byte is included

	#define RXERROR_OVERRUN 0x02
	#define RXERROR_PARITY 0x04
	#define RXERROR_FRAMING 0x08
	#define RXERROR_BREAK 0x10

	#define PORTSTATE_ENABLED 0x80
	#define PORTSTATE_TXFLUSH 0x01
	#define PORTSTATE_TXBREAK 0x02
	#define PORTSTATE_LOOPBACK 0x04

	// MSR bits

	#define USA_MSR_dCTS 0x01 // CTS has changed since last report
	#define USA_MSR_dDSR 0x02
	#define USA_MSR_dRI 0x04
	#define USA_MSR_dDCD 0x08

	#define USA_MSR_CTS 0x10 // current state of CTS
	#define USA_MSR_DSR 0x20
	#define USA_USA_MSR_RI 0x40
	#define MSR_DCD 0x80

	// ie: the maximum length of an endpoint buffer
	#define MAX_DATA_LEN 64

	#endif