| if ARCH_FEROCEON |
| |
| menu "Feroceon SoC options" |
| depends on ARCH_FEROCEON |
| |
| #since the Kconfig parser dispatch all source commands, we call the machines Kconfigs from here and |
| #not vice versa because otherwise the plat-feroceon Kconfig will be dispatched twice. |
| if ARCH_FEROCEON_KW2 |
| source "arch/arm/mach-feroceon-kw2/Kconfig" |
| endif |
| |
| config JTAG_DEBUG |
| bool "Enable JTAG by disable \"wait for interrupt\"." |
| depends on MV88F6500 || MV88F6281 || MV78XX0 |
| default n |
| ---help--- |
| Enable the JTAG debugger taking over the CPU by disabling "wait for interrupt" idle loop." |
| |
| |
| menu "Feroceon SoC Included Features" |
| |
| config MV_NAND_SUPPORT |
| bool |
| default n |
| |
| config MV_INCLUDE_PEX |
| bool "PCI Express Support" |
| depends on PCI && MV88F6500 || MV88F6281 || MV78XX0 |
| default y |
| ---help--- |
| Please don't change this configs unless you know what you are doing. |
| |
| config MV_INCLUDE_USB |
| bool "USB Support" |
| depends on MV88F6500 || MV88F6281 || MV78XX0 |
| default y |
| ---help--- |
| Please don't change this configs unless you know what you are doing. |
| |
| config MV_INCLUDE_XOR |
| bool "XOR Support" |
| depends on MV88F6500 || MV88F6281 || MV78XX0 |
| default y |
| ---help--- |
| Please don't change this configs unless you know what you are doing. |
| |
| config MV_INCLUDE_CESA |
| bool "CESA Support" |
| depends on MV88F6500 || MV88F6082 || MV88F6183 || MV88F6281 || MV78XX0 |
| default y |
| ---help--- |
| Please don't change this configs unless you know what you are doing. |
| |
| config MV_INCLUDE_NFC |
| bool "Nand Flash Controller Support" |
| select MV_NAND_SUPPORT |
| depends on MV88F6500 |
| default n |
| ---help--- |
| Please don't change this configs unless you know what you are doing. |
| |
| config MV_INCLUDE_LEGACY_NAND |
| bool "Legacy NAND Support" |
| select MV_NAND_SUPPORT |
| depends on MV88F6500 || MV88F6281 || MV78XX0 |
| default y |
| ---help--- |
| Please don't change this configs unless you know what you are doing. |
| |
| config MV_INCLUDE_INTEG_SATA |
| bool "Integrated SATA Support" |
| depends on MV88F6500 || MV88F6281 || MV78XX0 |
| default y |
| ---help--- |
| Please don't change this configs unless you know what you are doing. |
| |
| config MV_INCLUDE_TDM |
| bool "Integrated TDM Support" |
| depends on MV88F6500 || MV88F6281 || MV78XX0 |
| default y |
| ---help--- |
| Please don't change this configs unless you know what you are doing. |
| |
| config MV_INCLUDE_GIG_ETH |
| bool "Giga Ethernet Support" |
| depends on MV88F6500 || MV88F6281 || MV78XX0 |
| default y |
| |
| config MV_INCLUDE_SPI |
| bool "SPI Support" |
| depends on MV88F6500 || MV88F6281 || (MV78XX0 && !MV78XX0_Z0) |
| default y |
| ---help--- |
| Please don't change this configs unless you know what you are doing. |
| |
| config MV_INCLUDE_SDIO |
| bool "SDIO Support" |
| depends on MV88F6500 || MV88F6281 |
| default y |
| ---help--- |
| Please don't change this configs unless you know what you are doing. |
| |
| config MV_INCLUDE_TS |
| bool "TSU Support" |
| depends on MV88F6500 || MV88F6281 |
| default n |
| ---help--- |
| Please don't change this configs unless you know what you are doing. |
| |
| config MV_INCLUDE_PON |
| bool "PON Support" |
| depends on MV88F6500 |
| default y |
| ---help--- |
| Please don't change this configs unless you know what you are doing. |
| |
| config MV_INCLUDE_TPM |
| bool "TPM Support" |
| depends on MV88F6500 |
| default y |
| ---help--- |
| Please don't change this configs unless you know what you are doing. |
| |
| config MV_INCLUDE_CPH |
| bool "CPH Support" |
| depends on MV88F6500 |
| default y |
| ---help--- |
| Please don't change this configs unless you know what you are doing. |
| |
| config MV_INCLUDE_SWITCH |
| bool "Ethernet Switch Support" |
| depends on MV88F6500 || MV88F6281 || MV78XX0 |
| default y |
| |
| endmenu |
| |
| config MV_GPP_MAX_PINS |
| int |
| default 32 if MV78XX0 |
| default 64 if MV88F6281 |
| default 70 if MV88F6500 |
| |
| |
| config MV_DCACHE_SIZE |
| hex |
| default 0x8000 if MV78XX0 |
| default 0x4000 if MV88F6500 || MV88F6281 |
| |
| config MV_ICACHE_SIZE |
| hex |
| default 0x8000 if MV78XX0 |
| default 0x4000 if MV88F6500 || MV88F6281 |
| |
| menu "Feroceon SoC MTD support" |
| |
| config MV_FLASH_CTRL |
| bool |
| default n |
| |
| config MV_INCLUDE_NORFLASH_MTD |
| bool "Marvell support for MTD NOR flash device" |
| select MV_FLASH_CTRL |
| depends on MTD_CFI |
| default n |
| |
| config MV_INCLUDE_SFLASH_MTD |
| bool "Marvell support for MTD SPI flash device" |
| select MV_FLASH_CTRL |
| depends on MV_INCLUDE_SPI |
| default y |
| |
| config MTD_NAND_LNC |
| bool "Marvell support for legacy NAND controller" |
| depends on MV_INCLUDE_LEGACY_NAND |
| |
| config MTD_NAND_LNC_RS_ECC |
| bool "Support Reed-Solomon 4-bit ECC algorithm" |
| depends on MTD_NAND_LNC |
| default y |
| ---help--- |
| Choose this option to support Reed-Solomon 4-bit ECC algorithm. |
| Note this option also requires support by low-level boot loader. |
| |
| config MTD_NAND_LNC_8BYTE_READ |
| bool "Support NAND 8 Byte Read burst algorithm" |
| depends on MTD_NAND_LNC |
| ---help--- |
| Choose this option to support NAND 8 Byte Read burst algorithm. |
| |
| config MTD_NAND_NFC |
| tristate "MTD driver for the MV88F6500 Nand Flash Controller" |
| depends on MV_INCLUDE_NFC |
| help |
| This enables the driver for the NAND flash controller found in |
| the Marvell MV88F6500 SoC devices. |
| |
| config MTD_NAND_NFC_GANG_SUPPORT |
| bool "NAND Ganged mode support for the NFC" |
| depends on MTD_NAND_NFC |
| default y |
| help |
| This option enables the support for 2x8bit ganged mode in |
| Marvell's NFC HAL driver and the MTD stack. |
| |
| config MTD_NAND_NFC_MLC_SUPPORT |
| bool "NAND MLC devices support for the NFC" |
| depends on MTD_NAND_NFC |
| default y |
| help |
| This option allows support for Nand devices with non-standard |
| page/oob layout. These devices are detected incorrectly with |
| standard autodetection mechanism based on the READ_ID command. |
| |
| config MTD_NAND_NFC_INIT_RESET |
| bool "NAND Enable Reset on Initialization" |
| depends on MTD_NAND_NFC |
| default n |
| help |
| This option forces NAND reset command on initialization. This |
| is required by certain NAND vendors (Micron). |
| |
| endmenu |
| |
| choice |
| prompt "SoC USB Mode" |
| depends on MV_INCLUDE_USB && !UBOOT_STRUCT |
| default MV_USB_HOST |
| |
| config MV_USB_HOST |
| bool "Support for USB Host" |
| ---help--- |
| Choosing this option will configure on chip USB Controller to work in Host mode |
| |
| config MV_USB_DEVICE |
| bool "Support for USB Device" |
| ---help--- |
| Choosing this option will configure on chip USB Controller to work in Device mode |
| endchoice |
| |
| |
| config ARCH_SUPPORTS_BIG_ENDIAN |
| bool |
| default y |
| |
| config USE_DSP |
| bool "Use pld/ldrd/strd arm DSP instructions" |
| default n |
| |
| choice |
| prompt "Protect from speculative instruction prefetch" |
| depends on CACHE_FEROCEON_L2 |
| default MV_SP_I_FTCH_DB_INV |
| |
| config MV_SP_I_FTCH_DB_INV |
| bool "Double invalidate for DMA buffers" |
| ---help--- |
| Choosing this option will add L2 invalidate for DMA recieved buffers before processing it, |
| This is done through the pci_unmap_sg/page/single APIs. |
| |
| config MV_SP_I_FTCH_LCK_L2_ICACHE |
| bool "Lock L2 I-cache" |
| ---help--- |
| Choosing this option will lock L2 Icache. |
| |
| config MV_SP_I_FTCH_NONE |
| bool "Ignore" |
| |
| endchoice |
| |
| config MV_INTERNAL_REGS_SELECTIVE_MAPPING |
| bool "Internal registers selective mapping" |
| default n |
| ---help--- |
| Choosing this option enables selective address mapping for each unit, |
| in the internal registers address space. |
| |
| |
| config FEROCEON_PROC |
| bool "Support for MV-shell proc file system" |
| depends on PROC_FS |
| ---help--- |
| Choosing this option will enable you to use the MV-shell through the Proc |
| File system. |
| The MV-shell is a debug utility which can be run from the shell. |
| |
| config UBOOT_STRUCT |
| bool "Use UBoot Marvell tag structure" |
| ---help--- |
| Choosing this option will cause the linux to extract the Tclk, Sysclk and |
| the uboot version from the Tag list passed by the uboot. |
| |
| config MV_DBG_TRACE |
| bool "Enable tracing utility" |
| default n |
| ---help--- |
| Choosing this debug option will cause some kernel modules to log operations into |
| a cyclic buffer and dump them on failures. Enabling this feature decreases performance. |
| |
| config MV_REAL_TIME |
| bool "Real Time softirq support" |
| default n |
| ---help--- |
| Choosing this option will give more CPU time for user space processes |
| |
| config MV_CPU_PERF_CNTRS |
| bool "CPU Performance counters support" |
| default n |
| ---help--- |
| Choosing this option will enable you to use CPU Performance counters |
| |
| config MV_CPU_L2_PERF_CNTRS |
| bool "CPU L2 Performance counters support" |
| default n |
| ---help--- |
| Choosing this option will enable you to use CPU L2 Performance counters |
| |
| menu "Power-Management options" |
| |
| config MV_PMU_PROC |
| bool "Support procfs control on Power-Management features" |
| depends on PROC_FS |
| ---help--- |
| Choose this option to enable control over the power-management features through |
| the proc file-system. |
| |
| choice |
| prompt "Idle Mode" |
| depends on CPU_IDLE |
| default MV_PM_IDLE_WFI_SR |
| |
| config MV_PM_IDLE_WFI_SR |
| bool "Support WFI and DRAM SR for CPU-Idle driver" |
| ---help--- |
| Choosing this option will cause the CPU-Idle driver to enter WFI w/ DRAM Self-Refresh |
| when system is idle. |
| |
| config MV_PM_IDLE_DEEPIDLE_SR |
| bool "Support Deep-Idle and DRAM SR for CPU-Idle driver" |
| depends on MV_CESA_TOOL |
| ---help--- |
| Choosing this option will cause the CPU-Idle driver to enter Deep-Idle w/ DRAM Self-Refresh |
| when system is idle. |
| endchoice |
| endmenu |
| |
| |
| menu "Soc DMA accelerations" |
| |
| source arch/arm/plat-feroceon/mv_drivers_lsp/mv_xor/Kconfig |
| |
| source arch/arm/plat-feroceon/mv_drivers_lsp/mv_dma/Kconfig |
| |
| endmenu |
| |
| |
| menu "SoC Networking support" |
| depends on MV_INCLUDE_GIG_ETH |
| |
| config MV_ETHERNET |
| bool "Networking support" |
| depends on MV_INCLUDE_GIG_ETH |
| default y |
| ---help--- |
| Choose this option to support Marvell Gigabit Ethernet Controller |
| |
| if MV_ETHERNET |
| |
| choice |
| prompt "GbE Mode" |
| depends on MV_INCLUDE_GIG_ETH |
| default MV_ETH_LEGACY |
| |
| config MV_ETH_LEGACY |
| bool "Legacy mode " |
| ---help--- |
| |
| config MV_ETH_NETA |
| bool "Acceleration mode " |
| depends on ARCH_FEROCEON_KW2 |
| ---help--- |
| |
| endchoice |
| |
| |
| if MV_ETH_LEGACY |
| source arch/arm/plat-feroceon/mv_drivers_lsp/mv_network/Kconfig |
| endif |
| |
| if MV_ETH_NETA |
| source arch/arm/plat-feroceon/mv_drivers_lsp/mv_neta/Kconfig |
| endif |
| |
| endif # MV_ETHERNET |
| endmenu # "SoC Networking support" |
| |
| source arch/arm/plat-feroceon/mv_drivers_lsp/mv_cesa/Kconfig |
| |
| source arch/arm/plat-feroceon/mv_drivers_lsp/mv_phone/Kconfig |
| |
| |
| #source arch/arm/plat-feroceon/mv_drivers_lsp/mv_sdio/Kconfig |
| |
| source arch/arm/plat-feroceon/mv_drivers_lsp/mv_tsu/Kconfig |
| |
| source arch/arm/plat-feroceon/mv_drivers_lsp/mv_cph/Kconfig |
| |
| source arch/arm/plat-feroceon/mv_drivers_lsp/mv_pon/Kconfig |
| |
| source arch/arm/plat-feroceon/mv_drivers_lsp/mv_tpm/Kconfig |
| |
| source arch/arm/plat-feroceon/mv_drivers_lsp/mv_mac_learn/Kconfig |
| |
| config SCSI_MVSATA |
| tristate "Support for Marvell Sata Adapters" |
| depends on ( MV_INCLUDE_INTEG_SATA && SCSI ) || ( PCI && SCSI ) |
| ---help--- |
| Choosing this option will enable you to use the Marvell Sata |
| adapters support with emulation as SCSI adapters. |
| Note that the kernel scsi subsystem must be chosen too. |
| |
| source arch/arm/plat-feroceon/mv_drivers_lsp/mv_sata/Kconfig |
| |
| config PCIE_VIRTUAL_BRIDGE_SUPPORT |
| bool "Enable virtual bridge on PCIe" |
| depends on PCI |
| ---help--- |
| Enable virtual bridge module to support PCIe switches |
| |
| config MV_UART_POLLING_MODE |
| bool "Enable Polling mode for UART driver" |
| depends on ARCH_FEROCEON_KW2 |
| default y |
| ---help--- |
| Configure UART driver to work in polling mode. |
| |
| config MV_PRINTK_SLICE_SUPPORT |
| bool "Support printk buffer slicing" |
| depends on ARCH_FEROCEON_KW2 && PRINTK |
| default n |
| ---help--- |
| Enable printk buffer chunks slicing to reduce interrupts locking periods. |
| |
| config MV_PRINTK_CHUNK_SIZE |
| int "Support printk buffer slicing" |
| depends on MV_PRINTK_SLICE_SUPPORT |
| default 16 |
| ---help--- |
| Select printk buffer chunk granularity. |
| |
| choice |
| prompt "DRAM Access Configuration for 88F6601 SoC" |
| default MV_DRAM_DEFAULT_ACCESS_CFG |
| |
| config MV_DRAM_DEFAULT_ACCESS_CFG |
| bool "Default DRAM access configuration(by bootloader)" |
| ---help--- |
| Choosing this option keeps bootloader DRAM access configuration. |
| |
| config MV_DRAM_FASTPATH_ACCESS_CFG |
| bool "DRAM fast-path access configuration" |
| ---help--- |
| Choosing this option will enable DRAM fast-path access configuration. |
| |
| config MV_DRAM_XBAR_ACCESS_CFG |
| bool "DRAM XBAR access configuration" |
| ---help--- |
| Choosing this option will enable DRAM XBAR access configuration. |
| |
| endchoice |
| |
| endmenu |
| |
| |
| endif |
