| /* |
| * drivers/mtd/nand/pxa3xx_nand.c |
| * |
| * Copyright © 2005 Intel Corporation |
| * Copyright © 2006 Marvell International Ltd. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/interrupt.h> |
| #include <linux/platform_device.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/delay.h> |
| #include <linux/clk.h> |
| #include <linux/mtd/mtd.h> |
| #include <linux/mtd/nand.h> |
| #include <linux/mtd/partitions.h> |
| #include <linux/io.h> |
| #include <linux/irq.h> |
| |
| #include <mach/dma.h> |
| #include <mach/pxa3xx_nand.h> |
| |
| #define CHIP_DELAY_TIMEOUT (2 * HZ/10) |
| |
| /* registers and bit definitions */ |
| #define NDCR (0x00) /* Control register */ |
| #define NDTR0CS0 (0x04) /* Timing Parameter 0 for CS0 */ |
| #define NDTR1CS0 (0x0C) /* Timing Parameter 1 for CS0 */ |
| #define NDSR (0x14) /* Status Register */ |
| #define NDPCR (0x18) /* Page Count Register */ |
| #define NDBDR0 (0x1C) /* Bad Block Register 0 */ |
| #define NDBDR1 (0x20) /* Bad Block Register 1 */ |
| #define NDDB (0x40) /* Data Buffer */ |
| #define NDCB0 (0x48) /* Command Buffer0 */ |
| #define NDCB1 (0x4C) /* Command Buffer1 */ |
| #define NDCB2 (0x50) /* Command Buffer2 */ |
| |
| #define NDCR_SPARE_EN (0x1 << 31) |
| #define NDCR_ECC_EN (0x1 << 30) |
| #define NDCR_DMA_EN (0x1 << 29) |
| #define NDCR_ND_RUN (0x1 << 28) |
| #define NDCR_DWIDTH_C (0x1 << 27) |
| #define NDCR_DWIDTH_M (0x1 << 26) |
| #define NDCR_PAGE_SZ (0x1 << 24) |
| #define NDCR_NCSX (0x1 << 23) |
| #define NDCR_ND_MODE (0x3 << 21) |
| #define NDCR_NAND_MODE (0x0) |
| #define NDCR_CLR_PG_CNT (0x1 << 20) |
| #define NDCR_CLR_ECC (0x1 << 19) |
| #define NDCR_RD_ID_CNT_MASK (0x7 << 16) |
| #define NDCR_RD_ID_CNT(x) (((x) << 16) & NDCR_RD_ID_CNT_MASK) |
| |
| #define NDCR_RA_START (0x1 << 15) |
| #define NDCR_PG_PER_BLK (0x1 << 14) |
| #define NDCR_ND_ARB_EN (0x1 << 12) |
| |
| #define NDSR_MASK (0xfff) |
| #define NDSR_RDY (0x1 << 11) |
| #define NDSR_CS0_PAGED (0x1 << 10) |
| #define NDSR_CS1_PAGED (0x1 << 9) |
| #define NDSR_CS0_CMDD (0x1 << 8) |
| #define NDSR_CS1_CMDD (0x1 << 7) |
| #define NDSR_CS0_BBD (0x1 << 6) |
| #define NDSR_CS1_BBD (0x1 << 5) |
| #define NDSR_DBERR (0x1 << 4) |
| #define NDSR_SBERR (0x1 << 3) |
| #define NDSR_WRDREQ (0x1 << 2) |
| #define NDSR_RDDREQ (0x1 << 1) |
| #define NDSR_WRCMDREQ (0x1) |
| |
| #define NDCB0_AUTO_RS (0x1 << 25) |
| #define NDCB0_CSEL (0x1 << 24) |
| #define NDCB0_CMD_TYPE_MASK (0x7 << 21) |
| #define NDCB0_CMD_TYPE(x) (((x) << 21) & NDCB0_CMD_TYPE_MASK) |
| #define NDCB0_NC (0x1 << 20) |
| #define NDCB0_DBC (0x1 << 19) |
| #define NDCB0_ADDR_CYC_MASK (0x7 << 16) |
| #define NDCB0_ADDR_CYC(x) (((x) << 16) & NDCB0_ADDR_CYC_MASK) |
| #define NDCB0_CMD2_MASK (0xff << 8) |
| #define NDCB0_CMD1_MASK (0xff) |
| #define NDCB0_ADDR_CYC_SHIFT (16) |
| |
| /* dma-able I/O address for the NAND data and commands */ |
| #define NDCB0_DMA_ADDR (0x43100048) |
| #define NDDB_DMA_ADDR (0x43100040) |
| |
| /* macros for registers read/write */ |
| #define nand_writel(info, off, val) \ |
| __raw_writel((val), (info)->mmio_base + (off)) |
| |
| #define nand_readl(info, off) \ |
| __raw_readl((info)->mmio_base + (off)) |
| |
| /* error code and state */ |
| enum { |
| ERR_NONE = 0, |
| ERR_DMABUSERR = -1, |
| ERR_SENDCMD = -2, |
| ERR_DBERR = -3, |
| ERR_BBERR = -4, |
| ERR_SBERR = -5, |
| }; |
| |
| enum { |
| STATE_READY = 0, |
| STATE_CMD_HANDLE, |
| STATE_DMA_READING, |
| STATE_DMA_WRITING, |
| STATE_DMA_DONE, |
| STATE_PIO_READING, |
| STATE_PIO_WRITING, |
| }; |
| |
| struct pxa3xx_nand_info { |
| struct nand_chip nand_chip; |
| |
| struct platform_device *pdev; |
| const struct pxa3xx_nand_flash *flash_info; |
| |
| struct clk *clk; |
| void __iomem *mmio_base; |
| |
| unsigned int buf_start; |
| unsigned int buf_count; |
| |
| /* DMA information */ |
| int drcmr_dat; |
| int drcmr_cmd; |
| |
| unsigned char *data_buff; |
| dma_addr_t data_buff_phys; |
| size_t data_buff_size; |
| int data_dma_ch; |
| struct pxa_dma_desc *data_desc; |
| dma_addr_t data_desc_addr; |
| |
| uint32_t reg_ndcr; |
| |
| /* saved column/page_addr during CMD_SEQIN */ |
| int seqin_column; |
| int seqin_page_addr; |
| |
| /* relate to the command */ |
| unsigned int state; |
| |
| int use_ecc; /* use HW ECC ? */ |
| int use_dma; /* use DMA ? */ |
| |
| size_t data_size; /* data size in FIFO */ |
| int retcode; |
| struct completion cmd_complete; |
| |
| /* generated NDCBx register values */ |
| uint32_t ndcb0; |
| uint32_t ndcb1; |
| uint32_t ndcb2; |
| |
| /* calculated from pxa3xx_nand_flash data */ |
| size_t oob_size; |
| size_t read_id_bytes; |
| |
| unsigned int col_addr_cycles; |
| unsigned int row_addr_cycles; |
| }; |
| |
| static int use_dma = 1; |
| module_param(use_dma, bool, 0444); |
| MODULE_PARM_DESC(use_dma, "enable DMA for data transfering to/from NAND HW"); |
| |
| /* |
| * Default NAND flash controller configuration setup by the |
| * bootloader. This configuration is used only when pdata->keep_config is set |
| */ |
| static struct pxa3xx_nand_timing default_timing; |
| static struct pxa3xx_nand_flash default_flash; |
| |
| static struct pxa3xx_nand_cmdset smallpage_cmdset = { |
| .read1 = 0x0000, |
| .read2 = 0x0050, |
| .program = 0x1080, |
| .read_status = 0x0070, |
| .read_id = 0x0090, |
| .erase = 0xD060, |
| .reset = 0x00FF, |
| .lock = 0x002A, |
| .unlock = 0x2423, |
| .lock_status = 0x007A, |
| }; |
| |
| static struct pxa3xx_nand_cmdset largepage_cmdset = { |
| .read1 = 0x3000, |
| .read2 = 0x0050, |
| .program = 0x1080, |
| .read_status = 0x0070, |
| .read_id = 0x0090, |
| .erase = 0xD060, |
| .reset = 0x00FF, |
| .lock = 0x002A, |
| .unlock = 0x2423, |
| .lock_status = 0x007A, |
| }; |
| |
| #ifdef CONFIG_MTD_NAND_PXA3xx_BUILTIN |
| static struct pxa3xx_nand_timing samsung512MbX16_timing = { |
| .tCH = 10, |
| .tCS = 0, |
| .tWH = 20, |
| .tWP = 40, |
| .tRH = 30, |
| .tRP = 40, |
| .tR = 11123, |
| .tWHR = 110, |
| .tAR = 10, |
| }; |
| |
| static struct pxa3xx_nand_flash samsung512MbX16 = { |
| .timing = &samsung512MbX16_timing, |
| .cmdset = &smallpage_cmdset, |
| .page_per_block = 32, |
| .page_size = 512, |
| .flash_width = 16, |
| .dfc_width = 16, |
| .num_blocks = 4096, |
| .chip_id = 0x46ec, |
| }; |
| |
| static struct pxa3xx_nand_timing micron_timing = { |
| .tCH = 10, |
| .tCS = 25, |
| .tWH = 15, |
| .tWP = 25, |
| .tRH = 15, |
| .tRP = 25, |
| .tR = 25000, |
| .tWHR = 60, |
| .tAR = 10, |
| }; |
| |
| static struct pxa3xx_nand_flash micron1GbX8 = { |
| .timing = µn_timing, |
| .cmdset = &largepage_cmdset, |
| .page_per_block = 64, |
| .page_size = 2048, |
| .flash_width = 8, |
| .dfc_width = 8, |
| .num_blocks = 1024, |
| .chip_id = 0xa12c, |
| }; |
| |
| static struct pxa3xx_nand_flash micron1GbX16 = { |
| .timing = µn_timing, |
| .cmdset = &largepage_cmdset, |
| .page_per_block = 64, |
| .page_size = 2048, |
| .flash_width = 16, |
| .dfc_width = 16, |
| .num_blocks = 1024, |
| .chip_id = 0xb12c, |
| }; |
| |
| static struct pxa3xx_nand_timing stm2GbX16_timing = { |
| .tCH = 10, |
| .tCS = 35, |
| .tWH = 15, |
| .tWP = 25, |
| .tRH = 15, |
| .tRP = 25, |
| .tR = 25000, |
| .tWHR = 60, |
| .tAR = 10, |
| }; |
| |
| static struct pxa3xx_nand_flash stm2GbX16 = { |
| .timing = &stm2GbX16_timing, |
| .cmdset = &largepage_cmdset, |
| .page_per_block = 64, |
| .page_size = 2048, |
| .flash_width = 16, |
| .dfc_width = 16, |
| .num_blocks = 2048, |
| .chip_id = 0xba20, |
| }; |
| |
| static struct pxa3xx_nand_flash *builtin_flash_types[] = { |
| &samsung512MbX16, |
| µn1GbX8, |
| µn1GbX16, |
| &stm2GbX16, |
| }; |
| #endif /* CONFIG_MTD_NAND_PXA3xx_BUILTIN */ |
| |
| #define NDTR0_tCH(c) (min((c), 7) << 19) |
| #define NDTR0_tCS(c) (min((c), 7) << 16) |
| #define NDTR0_tWH(c) (min((c), 7) << 11) |
| #define NDTR0_tWP(c) (min((c), 7) << 8) |
| #define NDTR0_tRH(c) (min((c), 7) << 3) |
| #define NDTR0_tRP(c) (min((c), 7) << 0) |
| |
| #define NDTR1_tR(c) (min((c), 65535) << 16) |
| #define NDTR1_tWHR(c) (min((c), 15) << 4) |
| #define NDTR1_tAR(c) (min((c), 15) << 0) |
| |
| #define tCH_NDTR0(r) (((r) >> 19) & 0x7) |
| #define tCS_NDTR0(r) (((r) >> 16) & 0x7) |
| #define tWH_NDTR0(r) (((r) >> 11) & 0x7) |
| #define tWP_NDTR0(r) (((r) >> 8) & 0x7) |
| #define tRH_NDTR0(r) (((r) >> 3) & 0x7) |
| #define tRP_NDTR0(r) (((r) >> 0) & 0x7) |
| |
| #define tR_NDTR1(r) (((r) >> 16) & 0xffff) |
| #define tWHR_NDTR1(r) (((r) >> 4) & 0xf) |
| #define tAR_NDTR1(r) (((r) >> 0) & 0xf) |
| |
| /* convert nano-seconds to nand flash controller clock cycles */ |
| #define ns2cycle(ns, clk) (int)(((ns) * (clk / 1000000) / 1000) - 1) |
| |
| /* convert nand flash controller clock cycles to nano-seconds */ |
| #define cycle2ns(c, clk) ((((c) + 1) * 1000000 + clk / 500) / (clk / 1000)) |
| |
| static void pxa3xx_nand_set_timing(struct pxa3xx_nand_info *info, |
| const struct pxa3xx_nand_timing *t) |
| { |
| unsigned long nand_clk = clk_get_rate(info->clk); |
| uint32_t ndtr0, ndtr1; |
| |
| ndtr0 = NDTR0_tCH(ns2cycle(t->tCH, nand_clk)) | |
| NDTR0_tCS(ns2cycle(t->tCS, nand_clk)) | |
| NDTR0_tWH(ns2cycle(t->tWH, nand_clk)) | |
| NDTR0_tWP(ns2cycle(t->tWP, nand_clk)) | |
| NDTR0_tRH(ns2cycle(t->tRH, nand_clk)) | |
| NDTR0_tRP(ns2cycle(t->tRP, nand_clk)); |
| |
| ndtr1 = NDTR1_tR(ns2cycle(t->tR, nand_clk)) | |
| NDTR1_tWHR(ns2cycle(t->tWHR, nand_clk)) | |
| NDTR1_tAR(ns2cycle(t->tAR, nand_clk)); |
| |
| nand_writel(info, NDTR0CS0, ndtr0); |
| nand_writel(info, NDTR1CS0, ndtr1); |
| } |
| |
| #define WAIT_EVENT_TIMEOUT 10 |
| |
| static int wait_for_event(struct pxa3xx_nand_info *info, uint32_t event) |
| { |
| int timeout = WAIT_EVENT_TIMEOUT; |
| uint32_t ndsr; |
| |
| while (timeout--) { |
| ndsr = nand_readl(info, NDSR) & NDSR_MASK; |
| if (ndsr & event) { |
| nand_writel(info, NDSR, ndsr); |
| return 0; |
| } |
| udelay(10); |
| } |
| |
| return -ETIMEDOUT; |
| } |
| |
| static int prepare_read_prog_cmd(struct pxa3xx_nand_info *info, |
| uint16_t cmd, int column, int page_addr) |
| { |
| const struct pxa3xx_nand_flash *f = info->flash_info; |
| const struct pxa3xx_nand_cmdset *cmdset = f->cmdset; |
| |
| /* calculate data size */ |
| switch (f->page_size) { |
| case 2048: |
| info->data_size = (info->use_ecc) ? 2088 : 2112; |
| break; |
| case 512: |
| info->data_size = (info->use_ecc) ? 520 : 528; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| /* generate values for NDCBx registers */ |
| info->ndcb0 = cmd | ((cmd & 0xff00) ? NDCB0_DBC : 0); |
| info->ndcb1 = 0; |
| info->ndcb2 = 0; |
| info->ndcb0 |= NDCB0_ADDR_CYC(info->row_addr_cycles + info->col_addr_cycles); |
| |
| if (info->col_addr_cycles == 2) { |
| /* large block, 2 cycles for column address |
| * row address starts from 3rd cycle |
| */ |
| info->ndcb1 |= page_addr << 16; |
| if (info->row_addr_cycles == 3) |
| info->ndcb2 = (page_addr >> 16) & 0xff; |
| } else |
| /* small block, 1 cycles for column address |
| * row address starts from 2nd cycle |
| */ |
| info->ndcb1 = page_addr << 8; |
| |
| if (cmd == cmdset->program) |
| info->ndcb0 |= NDCB0_CMD_TYPE(1) | NDCB0_AUTO_RS; |
| |
| return 0; |
| } |
| |
| static int prepare_erase_cmd(struct pxa3xx_nand_info *info, |
| uint16_t cmd, int page_addr) |
| { |
| info->ndcb0 = cmd | ((cmd & 0xff00) ? NDCB0_DBC : 0); |
| info->ndcb0 |= NDCB0_CMD_TYPE(2) | NDCB0_AUTO_RS | NDCB0_ADDR_CYC(3); |
| info->ndcb1 = page_addr; |
| info->ndcb2 = 0; |
| return 0; |
| } |
| |
| static int prepare_other_cmd(struct pxa3xx_nand_info *info, uint16_t cmd) |
| { |
| const struct pxa3xx_nand_cmdset *cmdset = info->flash_info->cmdset; |
| |
| info->ndcb0 = cmd | ((cmd & 0xff00) ? NDCB0_DBC : 0); |
| info->ndcb1 = 0; |
| info->ndcb2 = 0; |
| |
| if (cmd == cmdset->read_id) { |
| info->ndcb0 |= NDCB0_CMD_TYPE(3); |
| info->data_size = 8; |
| } else if (cmd == cmdset->read_status) { |
| info->ndcb0 |= NDCB0_CMD_TYPE(4); |
| info->data_size = 8; |
| } else if (cmd == cmdset->reset || cmd == cmdset->lock || |
| cmd == cmdset->unlock) { |
| info->ndcb0 |= NDCB0_CMD_TYPE(5); |
| } else |
| return -EINVAL; |
| |
| return 0; |
| } |
| |
| static void enable_int(struct pxa3xx_nand_info *info, uint32_t int_mask) |
| { |
| uint32_t ndcr; |
| |
| ndcr = nand_readl(info, NDCR); |
| nand_writel(info, NDCR, ndcr & ~int_mask); |
| } |
| |
| static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask) |
| { |
| uint32_t ndcr; |
| |
| ndcr = nand_readl(info, NDCR); |
| nand_writel(info, NDCR, ndcr | int_mask); |
| } |
| |
| /* NOTE: it is a must to set ND_RUN firstly, then write command buffer |
| * otherwise, it does not work |
| */ |
| static int write_cmd(struct pxa3xx_nand_info *info) |
| { |
| uint32_t ndcr; |
| |
| /* clear status bits and run */ |
| nand_writel(info, NDSR, NDSR_MASK); |
| |
| ndcr = info->reg_ndcr; |
| |
| ndcr |= info->use_ecc ? NDCR_ECC_EN : 0; |
| ndcr |= info->use_dma ? NDCR_DMA_EN : 0; |
| ndcr |= NDCR_ND_RUN; |
| |
| nand_writel(info, NDCR, ndcr); |
| |
| if (wait_for_event(info, NDSR_WRCMDREQ)) { |
| printk(KERN_ERR "timed out writing command\n"); |
| return -ETIMEDOUT; |
| } |
| |
| nand_writel(info, NDCB0, info->ndcb0); |
| nand_writel(info, NDCB0, info->ndcb1); |
| nand_writel(info, NDCB0, info->ndcb2); |
| return 0; |
| } |
| |
| static int handle_data_pio(struct pxa3xx_nand_info *info) |
| { |
| int ret, timeout = CHIP_DELAY_TIMEOUT; |
| |
| switch (info->state) { |
| case STATE_PIO_WRITING: |
| __raw_writesl(info->mmio_base + NDDB, info->data_buff, |
| info->data_size << 2); |
| |
| enable_int(info, NDSR_CS0_BBD | NDSR_CS0_CMDD); |
| |
| ret = wait_for_completion_timeout(&info->cmd_complete, timeout); |
| if (!ret) { |
| printk(KERN_ERR "program command time out\n"); |
| return -1; |
| } |
| break; |
| case STATE_PIO_READING: |
| __raw_readsl(info->mmio_base + NDDB, info->data_buff, |
| info->data_size << 2); |
| break; |
| default: |
| printk(KERN_ERR "%s: invalid state %d\n", __func__, |
| info->state); |
| return -EINVAL; |
| } |
| |
| info->state = STATE_READY; |
| return 0; |
| } |
| |
| static void start_data_dma(struct pxa3xx_nand_info *info, int dir_out) |
| { |
| struct pxa_dma_desc *desc = info->data_desc; |
| int dma_len = ALIGN(info->data_size, 32); |
| |
| desc->ddadr = DDADR_STOP; |
| desc->dcmd = DCMD_ENDIRQEN | DCMD_WIDTH4 | DCMD_BURST32 | dma_len; |
| |
| if (dir_out) { |
| desc->dsadr = info->data_buff_phys; |
| desc->dtadr = NDDB_DMA_ADDR; |
| desc->dcmd |= DCMD_INCSRCADDR | DCMD_FLOWTRG; |
| } else { |
| desc->dtadr = info->data_buff_phys; |
| desc->dsadr = NDDB_DMA_ADDR; |
| desc->dcmd |= DCMD_INCTRGADDR | DCMD_FLOWSRC; |
| } |
| |
| DRCMR(info->drcmr_dat) = DRCMR_MAPVLD | info->data_dma_ch; |
| DDADR(info->data_dma_ch) = info->data_desc_addr; |
| DCSR(info->data_dma_ch) |= DCSR_RUN; |
| } |
| |
| static void pxa3xx_nand_data_dma_irq(int channel, void *data) |
| { |
| struct pxa3xx_nand_info *info = data; |
| uint32_t dcsr; |
| |
| dcsr = DCSR(channel); |
| DCSR(channel) = dcsr; |
| |
| if (dcsr & DCSR_BUSERR) { |
| info->retcode = ERR_DMABUSERR; |
| complete(&info->cmd_complete); |
| } |
| |
| if (info->state == STATE_DMA_WRITING) { |
| info->state = STATE_DMA_DONE; |
| enable_int(info, NDSR_CS0_BBD | NDSR_CS0_CMDD); |
| } else { |
| info->state = STATE_READY; |
| complete(&info->cmd_complete); |
| } |
| } |
| |
| static irqreturn_t pxa3xx_nand_irq(int irq, void *devid) |
| { |
| struct pxa3xx_nand_info *info = devid; |
| unsigned int status; |
| |
| status = nand_readl(info, NDSR); |
| |
| if (status & (NDSR_RDDREQ | NDSR_DBERR | NDSR_SBERR)) { |
| if (status & NDSR_DBERR) |
| info->retcode = ERR_DBERR; |
| else if (status & NDSR_SBERR) |
| info->retcode = ERR_SBERR; |
| |
| disable_int(info, NDSR_RDDREQ | NDSR_DBERR | NDSR_SBERR); |
| |
| if (info->use_dma) { |
| info->state = STATE_DMA_READING; |
| start_data_dma(info, 0); |
| } else { |
| info->state = STATE_PIO_READING; |
| complete(&info->cmd_complete); |
| } |
| } else if (status & NDSR_WRDREQ) { |
| disable_int(info, NDSR_WRDREQ); |
| if (info->use_dma) { |
| info->state = STATE_DMA_WRITING; |
| start_data_dma(info, 1); |
| } else { |
| info->state = STATE_PIO_WRITING; |
| complete(&info->cmd_complete); |
| } |
| } else if (status & (NDSR_CS0_BBD | NDSR_CS0_CMDD)) { |
| if (status & NDSR_CS0_BBD) |
| info->retcode = ERR_BBERR; |
| |
| disable_int(info, NDSR_CS0_BBD | NDSR_CS0_CMDD); |
| info->state = STATE_READY; |
| complete(&info->cmd_complete); |
| } |
| nand_writel(info, NDSR, status); |
| return IRQ_HANDLED; |
| } |
| |
| static int pxa3xx_nand_do_cmd(struct pxa3xx_nand_info *info, uint32_t event) |
| { |
| uint32_t ndcr; |
| int ret, timeout = CHIP_DELAY_TIMEOUT; |
| |
| if (write_cmd(info)) { |
| info->retcode = ERR_SENDCMD; |
| goto fail_stop; |
| } |
| |
| info->state = STATE_CMD_HANDLE; |
| |
| enable_int(info, event); |
| |
| ret = wait_for_completion_timeout(&info->cmd_complete, timeout); |
| if (!ret) { |
| printk(KERN_ERR "command execution timed out\n"); |
| info->retcode = ERR_SENDCMD; |
| goto fail_stop; |
| } |
| |
| if (info->use_dma == 0 && info->data_size > 0) |
| if (handle_data_pio(info)) |
| goto fail_stop; |
| |
| return 0; |
| |
| fail_stop: |
| ndcr = nand_readl(info, NDCR); |
| nand_writel(info, NDCR, ndcr & ~NDCR_ND_RUN); |
| udelay(10); |
| return -ETIMEDOUT; |
| } |
| |
| static int pxa3xx_nand_dev_ready(struct mtd_info *mtd) |
| { |
| struct pxa3xx_nand_info *info = mtd->priv; |
| return (nand_readl(info, NDSR) & NDSR_RDY) ? 1 : 0; |
| } |
| |
| static inline int is_buf_blank(uint8_t *buf, size_t len) |
| { |
| for (; len > 0; len--) |
| if (*buf++ != 0xff) |
| return 0; |
| return 1; |
| } |
| |
| static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command, |
| int column, int page_addr) |
| { |
| struct pxa3xx_nand_info *info = mtd->priv; |
| const struct pxa3xx_nand_flash *flash_info = info->flash_info; |
| const struct pxa3xx_nand_cmdset *cmdset = flash_info->cmdset; |
| int ret; |
| |
| info->use_dma = (use_dma) ? 1 : 0; |
| info->use_ecc = 0; |
| info->data_size = 0; |
| info->state = STATE_READY; |
| |
| init_completion(&info->cmd_complete); |
| |
| switch (command) { |
| case NAND_CMD_READOOB: |
| /* disable HW ECC to get all the OOB data */ |
| info->buf_count = mtd->writesize + mtd->oobsize; |
| info->buf_start = mtd->writesize + column; |
| |
| if (prepare_read_prog_cmd(info, cmdset->read1, column, page_addr)) |
| break; |
| |
| pxa3xx_nand_do_cmd(info, NDSR_RDDREQ | NDSR_DBERR | NDSR_SBERR); |
| |
| /* We only are OOB, so if the data has error, does not matter */ |
| if (info->retcode == ERR_DBERR) |
| info->retcode = ERR_NONE; |
| break; |
| |
| case NAND_CMD_READ0: |
| info->use_ecc = 1; |
| info->retcode = ERR_NONE; |
| info->buf_start = column; |
| info->buf_count = mtd->writesize + mtd->oobsize; |
| memset(info->data_buff, 0xFF, info->buf_count); |
| |
| if (prepare_read_prog_cmd(info, cmdset->read1, column, page_addr)) |
| break; |
| |
| pxa3xx_nand_do_cmd(info, NDSR_RDDREQ | NDSR_DBERR | NDSR_SBERR); |
| |
| if (info->retcode == ERR_DBERR) { |
| /* for blank page (all 0xff), HW will calculate its ECC as |
| * 0, which is different from the ECC information within |
| * OOB, ignore such double bit errors |
| */ |
| if (is_buf_blank(info->data_buff, mtd->writesize)) |
| info->retcode = ERR_NONE; |
| } |
| break; |
| case NAND_CMD_SEQIN: |
| info->buf_start = column; |
| info->buf_count = mtd->writesize + mtd->oobsize; |
| memset(info->data_buff, 0xff, info->buf_count); |
| |
| /* save column/page_addr for next CMD_PAGEPROG */ |
| info->seqin_column = column; |
| info->seqin_page_addr = page_addr; |
| break; |
| case NAND_CMD_PAGEPROG: |
| info->use_ecc = (info->seqin_column >= mtd->writesize) ? 0 : 1; |
| |
| if (prepare_read_prog_cmd(info, cmdset->program, |
| info->seqin_column, info->seqin_page_addr)) |
| break; |
| |
| pxa3xx_nand_do_cmd(info, NDSR_WRDREQ); |
| break; |
| case NAND_CMD_ERASE1: |
| if (prepare_erase_cmd(info, cmdset->erase, page_addr)) |
| break; |
| |
| pxa3xx_nand_do_cmd(info, NDSR_CS0_BBD | NDSR_CS0_CMDD); |
| break; |
| case NAND_CMD_ERASE2: |
| break; |
| case NAND_CMD_READID: |
| case NAND_CMD_STATUS: |
| info->use_dma = 0; /* force PIO read */ |
| info->buf_start = 0; |
| info->buf_count = (command == NAND_CMD_READID) ? |
| info->read_id_bytes : 1; |
| |
| if (prepare_other_cmd(info, (command == NAND_CMD_READID) ? |
| cmdset->read_id : cmdset->read_status)) |
| break; |
| |
| pxa3xx_nand_do_cmd(info, NDSR_RDDREQ); |
| break; |
| case NAND_CMD_RESET: |
| if (prepare_other_cmd(info, cmdset->reset)) |
| break; |
| |
| ret = pxa3xx_nand_do_cmd(info, NDSR_CS0_CMDD); |
| if (ret == 0) { |
| int timeout = 2; |
| uint32_t ndcr; |
| |
| while (timeout--) { |
| if (nand_readl(info, NDSR) & NDSR_RDY) |
| break; |
| msleep(10); |
| } |
| |
| ndcr = nand_readl(info, NDCR); |
| nand_writel(info, NDCR, ndcr & ~NDCR_ND_RUN); |
| } |
| break; |
| default: |
| printk(KERN_ERR "non-supported command.\n"); |
| break; |
| } |
| |
| if (info->retcode == ERR_DBERR) { |
| printk(KERN_ERR "double bit error @ page %08x\n", page_addr); |
| info->retcode = ERR_NONE; |
| } |
| } |
| |
| static uint8_t pxa3xx_nand_read_byte(struct mtd_info *mtd) |
| { |
| struct pxa3xx_nand_info *info = mtd->priv; |
| char retval = 0xFF; |
| |
| if (info->buf_start < info->buf_count) |
| /* Has just send a new command? */ |
| retval = info->data_buff[info->buf_start++]; |
| |
| return retval; |
| } |
| |
| static u16 pxa3xx_nand_read_word(struct mtd_info *mtd) |
| { |
| struct pxa3xx_nand_info *info = mtd->priv; |
| u16 retval = 0xFFFF; |
| |
| if (!(info->buf_start & 0x01) && info->buf_start < info->buf_count) { |
| retval = *((u16 *)(info->data_buff+info->buf_start)); |
| info->buf_start += 2; |
| } |
| return retval; |
| } |
| |
| static void pxa3xx_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) |
| { |
| struct pxa3xx_nand_info *info = mtd->priv; |
| int real_len = min_t(size_t, len, info->buf_count - info->buf_start); |
| |
| memcpy(buf, info->data_buff + info->buf_start, real_len); |
| info->buf_start += real_len; |
| } |
| |
| static void pxa3xx_nand_write_buf(struct mtd_info *mtd, |
| const uint8_t *buf, int len) |
| { |
| struct pxa3xx_nand_info *info = mtd->priv; |
| int real_len = min_t(size_t, len, info->buf_count - info->buf_start); |
| |
| memcpy(info->data_buff + info->buf_start, buf, real_len); |
| info->buf_start += real_len; |
| } |
| |
| static int pxa3xx_nand_verify_buf(struct mtd_info *mtd, |
| const uint8_t *buf, int len) |
| { |
| return 0; |
| } |
| |
| static void pxa3xx_nand_select_chip(struct mtd_info *mtd, int chip) |
| { |
| return; |
| } |
| |
| static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this) |
| { |
| struct pxa3xx_nand_info *info = mtd->priv; |
| |
| /* pxa3xx_nand_send_command has waited for command complete */ |
| if (this->state == FL_WRITING || this->state == FL_ERASING) { |
| if (info->retcode == ERR_NONE) |
| return 0; |
| else { |
| /* |
| * any error make it return 0x01 which will tell |
| * the caller the erase and write fail |
| */ |
| return 0x01; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static void pxa3xx_nand_ecc_hwctl(struct mtd_info *mtd, int mode) |
| { |
| return; |
| } |
| |
| static int pxa3xx_nand_ecc_calculate(struct mtd_info *mtd, |
| const uint8_t *dat, uint8_t *ecc_code) |
| { |
| return 0; |
| } |
| |
| static int pxa3xx_nand_ecc_correct(struct mtd_info *mtd, |
| uint8_t *dat, uint8_t *read_ecc, uint8_t *calc_ecc) |
| { |
| struct pxa3xx_nand_info *info = mtd->priv; |
| /* |
| * Any error include ERR_SEND_CMD, ERR_DBERR, ERR_BUSERR, we |
| * consider it as a ecc error which will tell the caller the |
| * read fail We have distinguish all the errors, but the |
| * nand_read_ecc only check this function return value |
| * |
| * Corrected (single-bit) errors must also be noted. |
| */ |
| if (info->retcode == ERR_SBERR) |
| return 1; |
| else if (info->retcode != ERR_NONE) |
| return -1; |
| |
| return 0; |
| } |
| |
| static int __readid(struct pxa3xx_nand_info *info, uint32_t *id) |
| { |
| const struct pxa3xx_nand_flash *f = info->flash_info; |
| const struct pxa3xx_nand_cmdset *cmdset = f->cmdset; |
| uint32_t ndcr; |
| uint8_t id_buff[8]; |
| |
| if (prepare_other_cmd(info, cmdset->read_id)) { |
| printk(KERN_ERR "failed to prepare command\n"); |
| return -EINVAL; |
| } |
| |
| /* Send command */ |
| if (write_cmd(info)) |
| goto fail_timeout; |
| |
| /* Wait for CMDDM(command done successfully) */ |
| if (wait_for_event(info, NDSR_RDDREQ)) |
| goto fail_timeout; |
| |
| __raw_readsl(info->mmio_base + NDDB, id_buff, 2); |
| *id = id_buff[0] | (id_buff[1] << 8); |
| return 0; |
| |
| fail_timeout: |
| ndcr = nand_readl(info, NDCR); |
| nand_writel(info, NDCR, ndcr & ~NDCR_ND_RUN); |
| udelay(10); |
| return -ETIMEDOUT; |
| } |
| |
| static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info, |
| const struct pxa3xx_nand_flash *f) |
| { |
| struct platform_device *pdev = info->pdev; |
| struct pxa3xx_nand_platform_data *pdata = pdev->dev.platform_data; |
| uint32_t ndcr = 0x00000FFF; /* disable all interrupts */ |
| |
| if (f->page_size != 2048 && f->page_size != 512) |
| return -EINVAL; |
| |
| if (f->flash_width != 16 && f->flash_width != 8) |
| return -EINVAL; |
| |
| /* calculate flash information */ |
| info->oob_size = (f->page_size == 2048) ? 64 : 16; |
| info->read_id_bytes = (f->page_size == 2048) ? 4 : 2; |
| |
| /* calculate addressing information */ |
| info->col_addr_cycles = (f->page_size == 2048) ? 2 : 1; |
| |
| if (f->num_blocks * f->page_per_block > 65536) |
| info->row_addr_cycles = 3; |
| else |
| info->row_addr_cycles = 2; |
| |
| ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0; |
| ndcr |= (info->col_addr_cycles == 2) ? NDCR_RA_START : 0; |
| ndcr |= (f->page_per_block == 64) ? NDCR_PG_PER_BLK : 0; |
| ndcr |= (f->page_size == 2048) ? NDCR_PAGE_SZ : 0; |
| ndcr |= (f->flash_width == 16) ? NDCR_DWIDTH_M : 0; |
| ndcr |= (f->dfc_width == 16) ? NDCR_DWIDTH_C : 0; |
| |
| ndcr |= NDCR_RD_ID_CNT(info->read_id_bytes); |
| ndcr |= NDCR_SPARE_EN; /* enable spare by default */ |
| |
| info->reg_ndcr = ndcr; |
| |
| pxa3xx_nand_set_timing(info, f->timing); |
| info->flash_info = f; |
| return 0; |
| } |
| |
| static void pxa3xx_nand_detect_timing(struct pxa3xx_nand_info *info, |
| struct pxa3xx_nand_timing *t) |
| { |
| unsigned long nand_clk = clk_get_rate(info->clk); |
| uint32_t ndtr0 = nand_readl(info, NDTR0CS0); |
| uint32_t ndtr1 = nand_readl(info, NDTR1CS0); |
| |
| t->tCH = cycle2ns(tCH_NDTR0(ndtr0), nand_clk); |
| t->tCS = cycle2ns(tCS_NDTR0(ndtr0), nand_clk); |
| t->tWH = cycle2ns(tWH_NDTR0(ndtr0), nand_clk); |
| t->tWP = cycle2ns(tWP_NDTR0(ndtr0), nand_clk); |
| t->tRH = cycle2ns(tRH_NDTR0(ndtr0), nand_clk); |
| t->tRP = cycle2ns(tRP_NDTR0(ndtr0), nand_clk); |
| |
| t->tR = cycle2ns(tR_NDTR1(ndtr1), nand_clk); |
| t->tWHR = cycle2ns(tWHR_NDTR1(ndtr1), nand_clk); |
| t->tAR = cycle2ns(tAR_NDTR1(ndtr1), nand_clk); |
| } |
| |
| static int pxa3xx_nand_detect_config(struct pxa3xx_nand_info *info) |
| { |
| uint32_t ndcr = nand_readl(info, NDCR); |
| struct nand_flash_dev *type = NULL; |
| uint32_t id = -1; |
| int i; |
| |
| default_flash.page_per_block = ndcr & NDCR_PG_PER_BLK ? 64 : 32; |
| default_flash.page_size = ndcr & NDCR_PAGE_SZ ? 2048 : 512; |
| default_flash.flash_width = ndcr & NDCR_DWIDTH_M ? 16 : 8; |
| default_flash.dfc_width = ndcr & NDCR_DWIDTH_C ? 16 : 8; |
| |
| if (default_flash.page_size == 2048) |
| default_flash.cmdset = &largepage_cmdset; |
| else |
| default_flash.cmdset = &smallpage_cmdset; |
| |
| /* set info fields needed to __readid */ |
| info->flash_info = &default_flash; |
| info->read_id_bytes = (default_flash.page_size == 2048) ? 4 : 2; |
| info->reg_ndcr = ndcr; |
| |
| if (__readid(info, &id)) |
| return -ENODEV; |
| |
| /* Lookup the flash id */ |
| id = (id >> 8) & 0xff; /* device id is byte 2 */ |
| for (i = 0; nand_flash_ids[i].name != NULL; i++) { |
| if (id == nand_flash_ids[i].id) { |
| type = &nand_flash_ids[i]; |
| break; |
| } |
| } |
| |
| if (!type) |
| return -ENODEV; |
| |
| /* fill the missing flash information */ |
| i = __ffs(default_flash.page_per_block * default_flash.page_size); |
| default_flash.num_blocks = type->chipsize << (20 - i); |
| |
| info->oob_size = (default_flash.page_size == 2048) ? 64 : 16; |
| |
| /* calculate addressing information */ |
| info->col_addr_cycles = (default_flash.page_size == 2048) ? 2 : 1; |
| |
| if (default_flash.num_blocks * default_flash.page_per_block > 65536) |
| info->row_addr_cycles = 3; |
| else |
| info->row_addr_cycles = 2; |
| |
| pxa3xx_nand_detect_timing(info, &default_timing); |
| default_flash.timing = &default_timing; |
| |
| return 0; |
| } |
| |
| static int pxa3xx_nand_detect_flash(struct pxa3xx_nand_info *info, |
| const struct pxa3xx_nand_platform_data *pdata) |
| { |
| const struct pxa3xx_nand_flash *f; |
| uint32_t id = -1; |
| int i; |
| |
| if (pdata->keep_config) |
| if (pxa3xx_nand_detect_config(info) == 0) |
| return 0; |
| |
| for (i = 0; i<pdata->num_flash; ++i) { |
| f = pdata->flash + i; |
| |
| if (pxa3xx_nand_config_flash(info, f)) |
| continue; |
| |
| if (__readid(info, &id)) |
| continue; |
| |
| if (id == f->chip_id) |
| return 0; |
| } |
| |
| #ifdef CONFIG_MTD_NAND_PXA3xx_BUILTIN |
| for (i = 0; i < ARRAY_SIZE(builtin_flash_types); i++) { |
| |
| f = builtin_flash_types[i]; |
| |
| if (pxa3xx_nand_config_flash(info, f)) |
| continue; |
| |
| if (__readid(info, &id)) |
| continue; |
| |
| if (id == f->chip_id) |
| return 0; |
| } |
| #endif |
| |
| dev_warn(&info->pdev->dev, |
| "failed to detect configured nand flash; found %04x instead of\n", |
| id); |
| return -ENODEV; |
| } |
| |
| /* the maximum possible buffer size for large page with OOB data |
| * is: 2048 + 64 = 2112 bytes, allocate a page here for both the |
| * data buffer and the DMA descriptor |
| */ |
| #define MAX_BUFF_SIZE PAGE_SIZE |
| |
| static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info) |
| { |
| struct platform_device *pdev = info->pdev; |
| int data_desc_offset = MAX_BUFF_SIZE - sizeof(struct pxa_dma_desc); |
| |
| if (use_dma == 0) { |
| info->data_buff = kmalloc(MAX_BUFF_SIZE, GFP_KERNEL); |
| if (info->data_buff == NULL) |
| return -ENOMEM; |
| return 0; |
| } |
| |
| info->data_buff = dma_alloc_coherent(&pdev->dev, MAX_BUFF_SIZE, |
| &info->data_buff_phys, GFP_KERNEL); |
| if (info->data_buff == NULL) { |
| dev_err(&pdev->dev, "failed to allocate dma buffer\n"); |
| return -ENOMEM; |
| } |
| |
| info->data_buff_size = MAX_BUFF_SIZE; |
| info->data_desc = (void *)info->data_buff + data_desc_offset; |
| info->data_desc_addr = info->data_buff_phys + data_desc_offset; |
| |
| info->data_dma_ch = pxa_request_dma("nand-data", DMA_PRIO_LOW, |
| pxa3xx_nand_data_dma_irq, info); |
| if (info->data_dma_ch < 0) { |
| dev_err(&pdev->dev, "failed to request data dma\n"); |
| dma_free_coherent(&pdev->dev, info->data_buff_size, |
| info->data_buff, info->data_buff_phys); |
| return info->data_dma_ch; |
| } |
| |
| return 0; |
| } |
| |
| static struct nand_ecclayout hw_smallpage_ecclayout = { |
| .eccbytes = 6, |
| .eccpos = {8, 9, 10, 11, 12, 13 }, |
| .oobfree = { {2, 6} } |
| }; |
| |
| static struct nand_ecclayout hw_largepage_ecclayout = { |
| .eccbytes = 24, |
| .eccpos = { |
| 40, 41, 42, 43, 44, 45, 46, 47, |
| 48, 49, 50, 51, 52, 53, 54, 55, |
| 56, 57, 58, 59, 60, 61, 62, 63}, |
| .oobfree = { {2, 38} } |
| }; |
| |
| static void pxa3xx_nand_init_mtd(struct mtd_info *mtd, |
| struct pxa3xx_nand_info *info) |
| { |
| const struct pxa3xx_nand_flash *f = info->flash_info; |
| struct nand_chip *this = &info->nand_chip; |
| |
| this->options = (f->flash_width == 16) ? NAND_BUSWIDTH_16: 0; |
| |
| this->waitfunc = pxa3xx_nand_waitfunc; |
| this->select_chip = pxa3xx_nand_select_chip; |
| this->dev_ready = pxa3xx_nand_dev_ready; |
| this->cmdfunc = pxa3xx_nand_cmdfunc; |
| this->read_word = pxa3xx_nand_read_word; |
| this->read_byte = pxa3xx_nand_read_byte; |
| this->read_buf = pxa3xx_nand_read_buf; |
| this->write_buf = pxa3xx_nand_write_buf; |
| this->verify_buf = pxa3xx_nand_verify_buf; |
| |
| this->ecc.mode = NAND_ECC_HW; |
| this->ecc.hwctl = pxa3xx_nand_ecc_hwctl; |
| this->ecc.calculate = pxa3xx_nand_ecc_calculate; |
| this->ecc.correct = pxa3xx_nand_ecc_correct; |
| this->ecc.size = f->page_size; |
| |
| if (f->page_size == 2048) |
| this->ecc.layout = &hw_largepage_ecclayout; |
| else |
| this->ecc.layout = &hw_smallpage_ecclayout; |
| |
| this->chip_delay = 25; |
| } |
| |
| static int pxa3xx_nand_probe(struct platform_device *pdev) |
| { |
| struct pxa3xx_nand_platform_data *pdata; |
| struct pxa3xx_nand_info *info; |
| struct nand_chip *this; |
| struct mtd_info *mtd; |
| struct resource *r; |
| int ret = 0, irq; |
| |
| pdata = pdev->dev.platform_data; |
| |
| if (!pdata) { |
| dev_err(&pdev->dev, "no platform data defined\n"); |
| return -ENODEV; |
| } |
| |
| mtd = kzalloc(sizeof(struct mtd_info) + sizeof(struct pxa3xx_nand_info), |
| GFP_KERNEL); |
| if (!mtd) { |
| dev_err(&pdev->dev, "failed to allocate memory\n"); |
| return -ENOMEM; |
| } |
| |
| info = (struct pxa3xx_nand_info *)(&mtd[1]); |
| info->pdev = pdev; |
| |
| this = &info->nand_chip; |
| mtd->priv = info; |
| mtd->owner = THIS_MODULE; |
| |
| info->clk = clk_get(&pdev->dev, NULL); |
| if (IS_ERR(info->clk)) { |
| dev_err(&pdev->dev, "failed to get nand clock\n"); |
| ret = PTR_ERR(info->clk); |
| goto fail_free_mtd; |
| } |
| clk_enable(info->clk); |
| |
| r = platform_get_resource(pdev, IORESOURCE_DMA, 0); |
| if (r == NULL) { |
| dev_err(&pdev->dev, "no resource defined for data DMA\n"); |
| ret = -ENXIO; |
| goto fail_put_clk; |
| } |
| info->drcmr_dat = r->start; |
| |
| r = platform_get_resource(pdev, IORESOURCE_DMA, 1); |
| if (r == NULL) { |
| dev_err(&pdev->dev, "no resource defined for command DMA\n"); |
| ret = -ENXIO; |
| goto fail_put_clk; |
| } |
| info->drcmr_cmd = r->start; |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) { |
| dev_err(&pdev->dev, "no IRQ resource defined\n"); |
| ret = -ENXIO; |
| goto fail_put_clk; |
| } |
| |
| r = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| if (r == NULL) { |
| dev_err(&pdev->dev, "no IO memory resource defined\n"); |
| ret = -ENODEV; |
| goto fail_put_clk; |
| } |
| |
| r = request_mem_region(r->start, resource_size(r), pdev->name); |
| if (r == NULL) { |
| dev_err(&pdev->dev, "failed to request memory resource\n"); |
| ret = -EBUSY; |
| goto fail_put_clk; |
| } |
| |
| info->mmio_base = ioremap(r->start, resource_size(r)); |
| if (info->mmio_base == NULL) { |
| dev_err(&pdev->dev, "ioremap() failed\n"); |
| ret = -ENODEV; |
| goto fail_free_res; |
| } |
| |
| ret = pxa3xx_nand_init_buff(info); |
| if (ret) |
| goto fail_free_io; |
| |
| ret = request_irq(IRQ_NAND, pxa3xx_nand_irq, IRQF_DISABLED, |
| pdev->name, info); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "failed to request IRQ\n"); |
| goto fail_free_buf; |
| } |
| |
| ret = pxa3xx_nand_detect_flash(info, pdata); |
| if (ret) { |
| dev_err(&pdev->dev, "failed to detect flash\n"); |
| ret = -ENODEV; |
| goto fail_free_irq; |
| } |
| |
| pxa3xx_nand_init_mtd(mtd, info); |
| |
| platform_set_drvdata(pdev, mtd); |
| |
| if (nand_scan(mtd, 1)) { |
| dev_err(&pdev->dev, "failed to scan nand\n"); |
| ret = -ENXIO; |
| goto fail_free_irq; |
| } |
| |
| return add_mtd_partitions(mtd, pdata->parts, pdata->nr_parts); |
| |
| fail_free_irq: |
| free_irq(IRQ_NAND, info); |
| fail_free_buf: |
| if (use_dma) { |
| pxa_free_dma(info->data_dma_ch); |
| dma_free_coherent(&pdev->dev, info->data_buff_size, |
| info->data_buff, info->data_buff_phys); |
| } else |
| kfree(info->data_buff); |
| fail_free_io: |
| iounmap(info->mmio_base); |
| fail_free_res: |
| release_mem_region(r->start, resource_size(r)); |
| fail_put_clk: |
| clk_disable(info->clk); |
| clk_put(info->clk); |
| fail_free_mtd: |
| kfree(mtd); |
| return ret; |
| } |
| |
| static int pxa3xx_nand_remove(struct platform_device *pdev) |
| { |
| struct mtd_info *mtd = platform_get_drvdata(pdev); |
| struct pxa3xx_nand_info *info = mtd->priv; |
| struct resource *r; |
| |
| platform_set_drvdata(pdev, NULL); |
| |
| del_mtd_device(mtd); |
| del_mtd_partitions(mtd); |
| free_irq(IRQ_NAND, info); |
| if (use_dma) { |
| pxa_free_dma(info->data_dma_ch); |
| dma_free_writecombine(&pdev->dev, info->data_buff_size, |
| info->data_buff, info->data_buff_phys); |
| } else |
| kfree(info->data_buff); |
| |
| iounmap(info->mmio_base); |
| r = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| release_mem_region(r->start, resource_size(r)); |
| |
| clk_disable(info->clk); |
| clk_put(info->clk); |
| |
| kfree(mtd); |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM |
| static int pxa3xx_nand_suspend(struct platform_device *pdev, pm_message_t state) |
| { |
| struct mtd_info *mtd = (struct mtd_info *)platform_get_drvdata(pdev); |
| struct pxa3xx_nand_info *info = mtd->priv; |
| |
| if (info->state != STATE_READY) { |
| dev_err(&pdev->dev, "driver busy, state = %d\n", info->state); |
| return -EAGAIN; |
| } |
| |
| return 0; |
| } |
| |
| static int pxa3xx_nand_resume(struct platform_device *pdev) |
| { |
| struct mtd_info *mtd = (struct mtd_info *)platform_get_drvdata(pdev); |
| struct pxa3xx_nand_info *info = mtd->priv; |
| |
| clk_enable(info->clk); |
| |
| return pxa3xx_nand_config_flash(info, info->flash_info); |
| } |
| #else |
| #define pxa3xx_nand_suspend NULL |
| #define pxa3xx_nand_resume NULL |
| #endif |
| |
| static struct platform_driver pxa3xx_nand_driver = { |
| .driver = { |
| .name = "pxa3xx-nand", |
| }, |
| .probe = pxa3xx_nand_probe, |
| .remove = pxa3xx_nand_remove, |
| .suspend = pxa3xx_nand_suspend, |
| .resume = pxa3xx_nand_resume, |
| }; |
| |
| static int __init pxa3xx_nand_init(void) |
| { |
| return platform_driver_register(&pxa3xx_nand_driver); |
| } |
| module_init(pxa3xx_nand_init); |
| |
| static void __exit pxa3xx_nand_exit(void) |
| { |
| platform_driver_unregister(&pxa3xx_nand_driver); |
| } |
| module_exit(pxa3xx_nand_exit); |
| |
| MODULE_LICENSE("GPL"); |
| MODULE_DESCRIPTION("PXA3xx NAND controller driver"); |