arch/mips/alchemy/mtx-1/board_setup.c

/*
 *
 * BRIEF MODULE DESCRIPTION
 *	4G Systems MTX-1 board setup.
 *
 * Copyright 2003, 2008 MontaVista Software Inc.
 * Author: MontaVista Software, Inc. <source@mvista.com>
 *         Bruno Randolf <bruno.randolf@4g-systems.biz>
 *
 *  This program is free software; you can redistribute  it and/or modify it
 *  under  the terms of  the GNU General  Public License as published by the
 *  Free Software Foundation;  either version 2 of the  License, or (at your
 *  option) any later version.
 *
 *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
 *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
 *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
 *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
 *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
 *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
 *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
 *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
 *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
 *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 *
 *  You should have received a copy of the  GNU General Public License along
 *  with this program; if not, write  to the Free Software Foundation, Inc.,
 *  675 Mass Ave, Cambridge, MA 02139, USA.
 */

#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/pm.h>

#include <asm/reboot.h>
#include <asm/mach-au1x00/au1000.h>

#include <prom.h>

static void mtx1_reset(char *c)
{
	/* Jump to the reset vector */
	__asm__ __volatile__("jr\t%0"::"r"(0xbfc00000));
}

static void mtx1_power_off(void)
{
	while (1)
		asm volatile (
		"	.set	mips32					\n"
		"	wait						\n"
		"	.set	mips0					\n");
}

void __init board_setup(void)
{
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
	/* Enable USB power switch */
	alchemy_gpio_direction_output(204, 0);
#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */

	/* Initialize sys_pinfunc */
	au_writel(SYS_PF_NI2, SYS_PINFUNC);

	/* Initialize GPIO */
	au_writel(~0, KSEG1ADDR(AU1000_SYS_PHYS_ADDR) + SYS_TRIOUTCLR);
	alchemy_gpio_direction_output(0, 0);	/* Disable M66EN (PCI 66MHz) */
	alchemy_gpio_direction_output(3, 1);	/* Disable PCI CLKRUN# */
	alchemy_gpio_direction_output(1, 1);	/* Enable EXT_IO3 */
	alchemy_gpio_direction_output(5, 0);	/* Disable eth PHY TX_ER */

	/* Enable LED and set it to green */
	alchemy_gpio_direction_output(211, 1);	/* green on */
	alchemy_gpio_direction_output(212, 0);	/* red off */

	pm_power_off = mtx1_power_off;
	_machine_halt = mtx1_power_off;
	_machine_restart = mtx1_reset;

	printk(KERN_INFO "4G Systems MTX-1 Board\n");
}

static int __init mtx1_init_irq(void)
{
	irq_set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
	irq_set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
	irq_set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
	irq_set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
	irq_set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);

	return 0;
}
arch_initcall(mtx1_init_irq);