| /* |
| * TXx9 SPI controller driver. |
| * |
| * Based on linux/arch/mips/tx4938/toshiba_rbtx4938/spi_txx9.c |
| * Copyright (C) 2000-2001 Toshiba Corporation |
| * |
| * 2003-2005 (c) MontaVista Software, Inc. This file is licensed under the |
| * terms of the GNU General Public License version 2. This program is |
| * licensed "as is" without any warranty of any kind, whether express |
| * or implied. |
| * |
| * Support for TX4938 in 2.6 - Manish Lachwani (mlachwani@mvista.com) |
| * |
| * Convert to generic SPI framework - Atsushi Nemoto (anemo@mba.ocn.ne.jp) |
| */ |
| #include <linux/init.h> |
| #include <linux/delay.h> |
| #include <linux/errno.h> |
| #include <linux/interrupt.h> |
| #include <linux/platform_device.h> |
| #include <linux/sched.h> |
| #include <linux/spinlock.h> |
| #include <linux/workqueue.h> |
| #include <linux/spi/spi.h> |
| #include <linux/err.h> |
| #include <linux/clk.h> |
| #include <linux/io.h> |
| #include <linux/module.h> |
| #include <asm/gpio.h> |
| |
| |
| #define SPI_FIFO_SIZE 4 |
| #define SPI_MAX_DIVIDER 0xff /* Max. value for SPCR1.SER */ |
| #define SPI_MIN_DIVIDER 1 /* Min. value for SPCR1.SER */ |
| |
| #define TXx9_SPMCR 0x00 |
| #define TXx9_SPCR0 0x04 |
| #define TXx9_SPCR1 0x08 |
| #define TXx9_SPFS 0x0c |
| #define TXx9_SPSR 0x14 |
| #define TXx9_SPDR 0x18 |
| |
| /* SPMCR : SPI Master Control */ |
| #define TXx9_SPMCR_OPMODE 0xc0 |
| #define TXx9_SPMCR_CONFIG 0x40 |
| #define TXx9_SPMCR_ACTIVE 0x80 |
| #define TXx9_SPMCR_SPSTP 0x02 |
| #define TXx9_SPMCR_BCLR 0x01 |
| |
| /* SPCR0 : SPI Control 0 */ |
| #define TXx9_SPCR0_TXIFL_MASK 0xc000 |
| #define TXx9_SPCR0_RXIFL_MASK 0x3000 |
| #define TXx9_SPCR0_SIDIE 0x0800 |
| #define TXx9_SPCR0_SOEIE 0x0400 |
| #define TXx9_SPCR0_RBSIE 0x0200 |
| #define TXx9_SPCR0_TBSIE 0x0100 |
| #define TXx9_SPCR0_IFSPSE 0x0010 |
| #define TXx9_SPCR0_SBOS 0x0004 |
| #define TXx9_SPCR0_SPHA 0x0002 |
| #define TXx9_SPCR0_SPOL 0x0001 |
| |
| /* SPSR : SPI Status */ |
| #define TXx9_SPSR_TBSI 0x8000 |
| #define TXx9_SPSR_RBSI 0x4000 |
| #define TXx9_SPSR_TBS_MASK 0x3800 |
| #define TXx9_SPSR_RBS_MASK 0x0700 |
| #define TXx9_SPSR_SPOE 0x0080 |
| #define TXx9_SPSR_IFSD 0x0008 |
| #define TXx9_SPSR_SIDLE 0x0004 |
| #define TXx9_SPSR_STRDY 0x0002 |
| #define TXx9_SPSR_SRRDY 0x0001 |
| |
| |
| struct txx9spi { |
| struct workqueue_struct *workqueue; |
| struct work_struct work; |
| spinlock_t lock; /* protect 'queue' */ |
| struct list_head queue; |
| wait_queue_head_t waitq; |
| void __iomem *membase; |
| int baseclk; |
| struct clk *clk; |
| u32 max_speed_hz, min_speed_hz; |
| int last_chipselect; |
| int last_chipselect_val; |
| }; |
| |
| static u32 txx9spi_rd(struct txx9spi *c, int reg) |
| { |
| return __raw_readl(c->membase + reg); |
| } |
| static void txx9spi_wr(struct txx9spi *c, u32 val, int reg) |
| { |
| __raw_writel(val, c->membase + reg); |
| } |
| |
| static void txx9spi_cs_func(struct spi_device *spi, struct txx9spi *c, |
| int on, unsigned int cs_delay) |
| { |
| int val = (spi->mode & SPI_CS_HIGH) ? on : !on; |
| if (on) { |
| /* deselect the chip with cs_change hint in last transfer */ |
| if (c->last_chipselect >= 0) |
| gpio_set_value(c->last_chipselect, |
| !c->last_chipselect_val); |
| c->last_chipselect = spi->chip_select; |
| c->last_chipselect_val = val; |
| } else { |
| c->last_chipselect = -1; |
| ndelay(cs_delay); /* CS Hold Time */ |
| } |
| gpio_set_value(spi->chip_select, val); |
| ndelay(cs_delay); /* CS Setup Time / CS Recovery Time */ |
| } |
| |
| static int txx9spi_setup(struct spi_device *spi) |
| { |
| struct txx9spi *c = spi_master_get_devdata(spi->master); |
| u8 bits_per_word; |
| |
| if (!spi->max_speed_hz |
| || spi->max_speed_hz > c->max_speed_hz |
| || spi->max_speed_hz < c->min_speed_hz) |
| return -EINVAL; |
| |
| bits_per_word = spi->bits_per_word; |
| if (bits_per_word != 8 && bits_per_word != 16) |
| return -EINVAL; |
| |
| if (gpio_direction_output(spi->chip_select, |
| !(spi->mode & SPI_CS_HIGH))) { |
| dev_err(&spi->dev, "Cannot setup GPIO for chipselect.\n"); |
| return -EINVAL; |
| } |
| |
| /* deselect chip */ |
| spin_lock(&c->lock); |
| txx9spi_cs_func(spi, c, 0, (NSEC_PER_SEC / 2) / spi->max_speed_hz); |
| spin_unlock(&c->lock); |
| |
| return 0; |
| } |
| |
| static irqreturn_t txx9spi_interrupt(int irq, void *dev_id) |
| { |
| struct txx9spi *c = dev_id; |
| |
| /* disable rx intr */ |
| txx9spi_wr(c, txx9spi_rd(c, TXx9_SPCR0) & ~TXx9_SPCR0_RBSIE, |
| TXx9_SPCR0); |
| wake_up(&c->waitq); |
| return IRQ_HANDLED; |
| } |
| |
| static void txx9spi_work_one(struct txx9spi *c, struct spi_message *m) |
| { |
| struct spi_device *spi = m->spi; |
| struct spi_transfer *t; |
| unsigned int cs_delay; |
| unsigned int cs_change = 1; |
| int status = 0; |
| u32 mcr; |
| u32 prev_speed_hz = 0; |
| u8 prev_bits_per_word = 0; |
| |
| /* CS setup/hold/recovery time in nsec */ |
| cs_delay = 100 + (NSEC_PER_SEC / 2) / spi->max_speed_hz; |
| |
| mcr = txx9spi_rd(c, TXx9_SPMCR); |
| if (unlikely((mcr & TXx9_SPMCR_OPMODE) == TXx9_SPMCR_ACTIVE)) { |
| dev_err(&spi->dev, "Bad mode.\n"); |
| status = -EIO; |
| goto exit; |
| } |
| mcr &= ~(TXx9_SPMCR_OPMODE | TXx9_SPMCR_SPSTP | TXx9_SPMCR_BCLR); |
| |
| /* enter config mode */ |
| txx9spi_wr(c, mcr | TXx9_SPMCR_CONFIG | TXx9_SPMCR_BCLR, TXx9_SPMCR); |
| txx9spi_wr(c, TXx9_SPCR0_SBOS |
| | ((spi->mode & SPI_CPOL) ? TXx9_SPCR0_SPOL : 0) |
| | ((spi->mode & SPI_CPHA) ? TXx9_SPCR0_SPHA : 0) |
| | 0x08, |
| TXx9_SPCR0); |
| |
| list_for_each_entry (t, &m->transfers, transfer_list) { |
| const void *txbuf = t->tx_buf; |
| void *rxbuf = t->rx_buf; |
| u32 data; |
| unsigned int len = t->len; |
| unsigned int wsize; |
| u32 speed_hz = t->speed_hz ? : spi->max_speed_hz; |
| u8 bits_per_word = t->bits_per_word ? : spi->bits_per_word; |
| |
| bits_per_word = bits_per_word ? : 8; |
| wsize = bits_per_word >> 3; /* in bytes */ |
| |
| if (prev_speed_hz != speed_hz |
| || prev_bits_per_word != bits_per_word) { |
| int n = DIV_ROUND_UP(c->baseclk, speed_hz) - 1; |
| n = clamp(n, SPI_MIN_DIVIDER, SPI_MAX_DIVIDER); |
| /* enter config mode */ |
| txx9spi_wr(c, mcr | TXx9_SPMCR_CONFIG | TXx9_SPMCR_BCLR, |
| TXx9_SPMCR); |
| txx9spi_wr(c, (n << 8) | bits_per_word, TXx9_SPCR1); |
| /* enter active mode */ |
| txx9spi_wr(c, mcr | TXx9_SPMCR_ACTIVE, TXx9_SPMCR); |
| |
| prev_speed_hz = speed_hz; |
| prev_bits_per_word = bits_per_word; |
| } |
| |
| if (cs_change) |
| txx9spi_cs_func(spi, c, 1, cs_delay); |
| cs_change = t->cs_change; |
| while (len) { |
| unsigned int count = SPI_FIFO_SIZE; |
| int i; |
| u32 cr0; |
| |
| if (len < count * wsize) |
| count = len / wsize; |
| /* now tx must be idle... */ |
| while (!(txx9spi_rd(c, TXx9_SPSR) & TXx9_SPSR_SIDLE)) |
| cpu_relax(); |
| cr0 = txx9spi_rd(c, TXx9_SPCR0); |
| cr0 &= ~TXx9_SPCR0_RXIFL_MASK; |
| cr0 |= (count - 1) << 12; |
| /* enable rx intr */ |
| cr0 |= TXx9_SPCR0_RBSIE; |
| txx9spi_wr(c, cr0, TXx9_SPCR0); |
| /* send */ |
| for (i = 0; i < count; i++) { |
| if (txbuf) { |
| data = (wsize == 1) |
| ? *(const u8 *)txbuf |
| : *(const u16 *)txbuf; |
| txx9spi_wr(c, data, TXx9_SPDR); |
| txbuf += wsize; |
| } else |
| txx9spi_wr(c, 0, TXx9_SPDR); |
| } |
| /* wait all rx data */ |
| wait_event(c->waitq, |
| txx9spi_rd(c, TXx9_SPSR) & TXx9_SPSR_RBSI); |
| /* receive */ |
| for (i = 0; i < count; i++) { |
| data = txx9spi_rd(c, TXx9_SPDR); |
| if (rxbuf) { |
| if (wsize == 1) |
| *(u8 *)rxbuf = data; |
| else |
| *(u16 *)rxbuf = data; |
| rxbuf += wsize; |
| } |
| } |
| len -= count * wsize; |
| } |
| m->actual_length += t->len; |
| if (t->delay_usecs) |
| udelay(t->delay_usecs); |
| |
| if (!cs_change) |
| continue; |
| if (t->transfer_list.next == &m->transfers) |
| break; |
| /* sometimes a short mid-message deselect of the chip |
| * may be needed to terminate a mode or command |
| */ |
| txx9spi_cs_func(spi, c, 0, cs_delay); |
| } |
| |
| exit: |
| m->status = status; |
| m->complete(m->context); |
| |
| /* normally deactivate chipselect ... unless no error and |
| * cs_change has hinted that the next message will probably |
| * be for this chip too. |
| */ |
| if (!(status == 0 && cs_change)) |
| txx9spi_cs_func(spi, c, 0, cs_delay); |
| |
| /* enter config mode */ |
| txx9spi_wr(c, mcr | TXx9_SPMCR_CONFIG | TXx9_SPMCR_BCLR, TXx9_SPMCR); |
| } |
| |
| static void txx9spi_work(struct work_struct *work) |
| { |
| struct txx9spi *c = container_of(work, struct txx9spi, work); |
| unsigned long flags; |
| |
| spin_lock_irqsave(&c->lock, flags); |
| while (!list_empty(&c->queue)) { |
| struct spi_message *m; |
| |
| m = container_of(c->queue.next, struct spi_message, queue); |
| list_del_init(&m->queue); |
| spin_unlock_irqrestore(&c->lock, flags); |
| |
| txx9spi_work_one(c, m); |
| |
| spin_lock_irqsave(&c->lock, flags); |
| } |
| spin_unlock_irqrestore(&c->lock, flags); |
| } |
| |
| static int txx9spi_transfer(struct spi_device *spi, struct spi_message *m) |
| { |
| struct spi_master *master = spi->master; |
| struct txx9spi *c = spi_master_get_devdata(master); |
| struct spi_transfer *t; |
| unsigned long flags; |
| |
| m->actual_length = 0; |
| |
| /* check each transfer's parameters */ |
| list_for_each_entry (t, &m->transfers, transfer_list) { |
| u32 speed_hz = t->speed_hz ? : spi->max_speed_hz; |
| u8 bits_per_word = t->bits_per_word ? : spi->bits_per_word; |
| |
| bits_per_word = bits_per_word ? : 8; |
| if (!t->tx_buf && !t->rx_buf && t->len) |
| return -EINVAL; |
| if (bits_per_word != 8 && bits_per_word != 16) |
| return -EINVAL; |
| if (t->len & ((bits_per_word >> 3) - 1)) |
| return -EINVAL; |
| if (speed_hz < c->min_speed_hz || speed_hz > c->max_speed_hz) |
| return -EINVAL; |
| } |
| |
| spin_lock_irqsave(&c->lock, flags); |
| list_add_tail(&m->queue, &c->queue); |
| queue_work(c->workqueue, &c->work); |
| spin_unlock_irqrestore(&c->lock, flags); |
| |
| return 0; |
| } |
| |
| static int __init txx9spi_probe(struct platform_device *dev) |
| { |
| struct spi_master *master; |
| struct txx9spi *c; |
| struct resource *res; |
| int ret = -ENODEV; |
| u32 mcr; |
| int irq; |
| |
| master = spi_alloc_master(&dev->dev, sizeof(*c)); |
| if (!master) |
| return ret; |
| c = spi_master_get_devdata(master); |
| platform_set_drvdata(dev, master); |
| |
| INIT_WORK(&c->work, txx9spi_work); |
| spin_lock_init(&c->lock); |
| INIT_LIST_HEAD(&c->queue); |
| init_waitqueue_head(&c->waitq); |
| |
| c->clk = clk_get(&dev->dev, "spi-baseclk"); |
| if (IS_ERR(c->clk)) { |
| ret = PTR_ERR(c->clk); |
| c->clk = NULL; |
| goto exit; |
| } |
| ret = clk_enable(c->clk); |
| if (ret) { |
| clk_put(c->clk); |
| c->clk = NULL; |
| goto exit; |
| } |
| c->baseclk = clk_get_rate(c->clk); |
| c->min_speed_hz = DIV_ROUND_UP(c->baseclk, SPI_MAX_DIVIDER + 1); |
| c->max_speed_hz = c->baseclk / (SPI_MIN_DIVIDER + 1); |
| |
| res = platform_get_resource(dev, IORESOURCE_MEM, 0); |
| if (!res) |
| goto exit_busy; |
| if (!devm_request_mem_region(&dev->dev, res->start, resource_size(res), |
| "spi_txx9")) |
| goto exit_busy; |
| c->membase = devm_ioremap(&dev->dev, res->start, resource_size(res)); |
| if (!c->membase) |
| goto exit_busy; |
| |
| /* enter config mode */ |
| mcr = txx9spi_rd(c, TXx9_SPMCR); |
| mcr &= ~(TXx9_SPMCR_OPMODE | TXx9_SPMCR_SPSTP | TXx9_SPMCR_BCLR); |
| txx9spi_wr(c, mcr | TXx9_SPMCR_CONFIG | TXx9_SPMCR_BCLR, TXx9_SPMCR); |
| |
| irq = platform_get_irq(dev, 0); |
| if (irq < 0) |
| goto exit_busy; |
| ret = devm_request_irq(&dev->dev, irq, txx9spi_interrupt, 0, |
| "spi_txx9", c); |
| if (ret) |
| goto exit; |
| |
| c->workqueue = create_singlethread_workqueue( |
| dev_name(master->dev.parent)); |
| if (!c->workqueue) |
| goto exit_busy; |
| c->last_chipselect = -1; |
| |
| dev_info(&dev->dev, "at %#llx, irq %d, %dMHz\n", |
| (unsigned long long)res->start, irq, |
| (c->baseclk + 500000) / 1000000); |
| |
| /* the spi->mode bits understood by this driver: */ |
| master->mode_bits = SPI_CS_HIGH | SPI_CPOL | SPI_CPHA; |
| |
| master->bus_num = dev->id; |
| master->setup = txx9spi_setup; |
| master->transfer = txx9spi_transfer; |
| master->num_chipselect = (u16)UINT_MAX; /* any GPIO numbers */ |
| |
| ret = spi_register_master(master); |
| if (ret) |
| goto exit; |
| return 0; |
| exit_busy: |
| ret = -EBUSY; |
| exit: |
| if (c->workqueue) |
| destroy_workqueue(c->workqueue); |
| if (c->clk) { |
| clk_disable(c->clk); |
| clk_put(c->clk); |
| } |
| platform_set_drvdata(dev, NULL); |
| spi_master_put(master); |
| return ret; |
| } |
| |
| static int __exit txx9spi_remove(struct platform_device *dev) |
| { |
| struct spi_master *master = spi_master_get(platform_get_drvdata(dev)); |
| struct txx9spi *c = spi_master_get_devdata(master); |
| |
| spi_unregister_master(master); |
| platform_set_drvdata(dev, NULL); |
| destroy_workqueue(c->workqueue); |
| clk_disable(c->clk); |
| clk_put(c->clk); |
| spi_master_put(master); |
| return 0; |
| } |
| |
| /* work with hotplug and coldplug */ |
| MODULE_ALIAS("platform:spi_txx9"); |
| |
| static struct platform_driver txx9spi_driver = { |
| .remove = __exit_p(txx9spi_remove), |
| .driver = { |
| .name = "spi_txx9", |
| .owner = THIS_MODULE, |
| }, |
| }; |
| |
| static int __init txx9spi_init(void) |
| { |
| return platform_driver_probe(&txx9spi_driver, txx9spi_probe); |
| } |
| subsys_initcall(txx9spi_init); |
| |
| static void __exit txx9spi_exit(void) |
| { |
| platform_driver_unregister(&txx9spi_driver); |
| } |
| module_exit(txx9spi_exit); |
| |
| MODULE_DESCRIPTION("TXx9 SPI Driver"); |
| MODULE_LICENSE("GPL"); |