| /* |
| * Designware SPI core controller driver (refer pxa2xx_spi.c) |
| * |
| * Copyright (c) 2009, Intel Corporation. |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms and conditions of the GNU General Public License, |
| * version 2, as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope it will be useful, but WITHOUT |
| * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or |
| * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for |
| * more details. |
| * |
| * You should have received a copy of the GNU General Public License along with |
| * this program; if not, write to the Free Software Foundation, Inc., |
| * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. |
| */ |
| |
| #include <linux/dma-mapping.h> |
| #include <linux/interrupt.h> |
| #include <linux/module.h> |
| #include <linux/highmem.h> |
| #include <linux/delay.h> |
| #include <linux/slab.h> |
| #include <linux/spi/spi.h> |
| #include <linux/clk.h> |
| |
| #ifdef CONFIG_C2K_DEVFREQ_DW |
| #include <linux/c2k-devfreq.h> |
| #include <linux/devfreq.h> |
| #endif |
| |
| #include "spi-dw.h" |
| |
| #ifdef CONFIG_DEBUG_FS |
| #include <linux/debugfs.h> |
| #endif |
| |
| #define START_STATE ((void *)0) |
| #define RUNNING_STATE ((void *)1) |
| #define DONE_STATE ((void *)2) |
| #define ERROR_STATE ((void *)-1) |
| |
| #define QUEUE_RUNNING 0 |
| #define QUEUE_STOPPED 1 |
| |
| #define MRST_SPI_DEASSERT 0 |
| #define MRST_SPI_ASSERT 1 |
| |
| /* Slave spi_dev related */ |
| struct chip_data { |
| u16 cr0; |
| u8 cs; /* chip select pin */ |
| u8 n_bytes; /* current is a 1/2/4 byte op */ |
| u8 tmode; /* TR/TO/RO/EEPROM */ |
| u8 type; /* SPI/SSP/MicroWire */ |
| |
| u8 poll_mode; /* 1 means use poll mode */ |
| |
| u32 dma_width; |
| u32 rx_threshold; |
| u32 tx_threshold; |
| u8 enable_dma; |
| u8 bits_per_word; |
| u16 clk_div; /* baud rate divider */ |
| u32 speed_hz; /* baud rate */ |
| void (*cs_control)(u32 command); |
| }; |
| |
| #ifdef CONFIG_C2K_DEVFREQ_DW |
| static devfreq_counters dc; |
| |
| static int set_spi_freq(struct c2k_devfreq_data *data, unsigned long *freq) |
| { |
| struct spi_device *spi = container_of(data->dev, struct spi_device, dev); |
| struct dw_spi *dws = container_of(&spi, struct dw_spi, cur_dev); |
| struct chip_data *chip; |
| u32 clk_div; |
| |
| /* Only alloc on first setup */ |
| chip = spi_get_ctldata(spi); |
| |
| if (!chip) |
| { |
| chip = spi_get_ctldata(spi); |
| if (!chip) { |
| chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL); |
| if (!chip) |
| return -ENOMEM; |
| } |
| } |
| |
| if ((*freq <= data->max_freq) && (*freq >= data->min_freq)) |
| { |
| chip->speed_hz = (u32)*freq; |
| clk_div = dws->max_freq / chip->speed_hz; |
| clk_div = (clk_div + 1) & 0xfffe; |
| |
| chip->clk_div = clk_div; |
| spi_set_clk(dws, chip->clk_div); |
| } |
| else |
| { |
| printk (KERN_ERR "%s: Trying to set out of range spi freq: %lu\n\ |
| ", __func__, *freq); |
| } |
| |
| return 0; |
| } |
| #endif |
| |
| #ifdef CONFIG_DEBUG_FS |
| static int spi_show_regs_open(struct inode *inode, struct file *file) |
| { |
| file->private_data = inode->i_private; |
| return 0; |
| } |
| |
| #define SPI_REGS_BUFSIZE 1024 |
| static ssize_t spi_show_regs(struct file *file, char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct dw_spi *dws; |
| char *buf; |
| u32 len = 0; |
| ssize_t ret; |
| |
| dws = file->private_data; |
| |
| buf = kzalloc(SPI_REGS_BUFSIZE, GFP_KERNEL); |
| if (!buf) |
| return 0; |
| |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "MRST SPI0 registers:\n"); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "=================================\n"); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "CTRL0: \t\t0x%08x\n", dw_readl(dws, DW_SPI_CTRL0)); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "CTRL1: \t\t0x%08x\n", dw_readl(dws, DW_SPI_CTRL1)); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "SSIENR: \t0x%08x\n", dw_readl(dws, DW_SPI_SSIENR)); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "SER: \t\t0x%08x\n", dw_readl(dws, DW_SPI_SER)); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "BAUDR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_BAUDR)); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "TXFTLR: \t0x%08x\n", dw_readl(dws, DW_SPI_TXFLTR)); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "RXFTLR: \t0x%08x\n", dw_readl(dws, DW_SPI_RXFLTR)); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "TXFLR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_TXFLR)); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "RXFLR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_RXFLR)); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "SR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_SR)); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "IMR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_IMR)); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "ISR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_ISR)); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "DMACR: \t\t0x%08x\n", dw_readl(dws, DW_SPI_DMACR)); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "DMATDLR: \t0x%08x\n", dw_readl(dws, DW_SPI_DMATDLR)); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "DMARDLR: \t0x%08x\n", dw_readl(dws, DW_SPI_DMARDLR)); |
| len += snprintf(buf + len, SPI_REGS_BUFSIZE - len, |
| "=================================\n"); |
| |
| ret = simple_read_from_buffer(user_buf, count, ppos, buf, len); |
| kfree(buf); |
| return ret; |
| } |
| |
| static const struct file_operations mrst_spi_regs_ops = { |
| .owner = THIS_MODULE, |
| .open = spi_show_regs_open, |
| .read = spi_show_regs, |
| .llseek = default_llseek, |
| }; |
| |
| static int mrst_spi_debugfs_init(struct dw_spi *dws) |
| { |
| dws->debugfs = debugfs_create_dir("mrst_spi", NULL); |
| if (!dws->debugfs) |
| return -ENOMEM; |
| |
| debugfs_create_file("registers", S_IFREG | S_IRUGO, |
| dws->debugfs, (void *)dws, &mrst_spi_regs_ops); |
| return 0; |
| } |
| |
| static void mrst_spi_debugfs_remove(struct dw_spi *dws) |
| { |
| if (dws->debugfs) |
| debugfs_remove_recursive(dws->debugfs); |
| } |
| |
| #else |
| static inline int mrst_spi_debugfs_init(struct dw_spi *dws) |
| { |
| return 0; |
| } |
| |
| static inline void mrst_spi_debugfs_remove(struct dw_spi *dws) |
| { |
| } |
| #endif /* CONFIG_DEBUG_FS */ |
| |
| /* Return the max entries we can fill into tx fifo */ |
| static inline u32 tx_max(struct dw_spi *dws) |
| { |
| u32 tx_left, tx_room, rxtx_gap; |
| |
| tx_left = (dws->tx_end - dws->tx) / dws->n_bytes; |
| tx_room = dws->fifo_len - dw_readw(dws, DW_SPI_TXFLR); |
| |
| /* |
| * Another concern is about the tx/rx mismatch, we |
| * though to use (dws->fifo_len - rxflr - txflr) as |
| * one maximum value for tx, but it doesn't cover the |
| * data which is out of tx/rx fifo and inside the |
| * shift registers. So a control from sw point of |
| * view is taken. |
| */ |
| rxtx_gap = ((dws->rx_end - dws->rx) - (dws->tx_end - dws->tx)) |
| / dws->n_bytes; |
| |
| return min3(tx_left, tx_room, (u32) (dws->fifo_len - rxtx_gap)); |
| } |
| |
| /* Return the max entries we should read out of rx fifo */ |
| static inline u32 rx_max(struct dw_spi *dws) |
| { |
| u32 rx_left = (dws->rx_end - dws->rx) / dws->n_bytes; |
| |
| return min(rx_left, (u32)dw_readw(dws, DW_SPI_RXFLR)); |
| } |
| |
| static void dw_writer(struct dw_spi *dws) |
| { |
| u32 max = tx_max(dws); |
| u16 txw = 0; |
| |
| while (max--) { |
| /* Set the tx word if the transfer's original "tx" is not null */ |
| if (dws->tx_end - dws->len) { |
| if (dws->n_bytes == 1) |
| txw = *(u8 *)(dws->tx); |
| else |
| txw = *(u16 *)(dws->tx); |
| } |
| dw_writew(dws, DW_SPI_DR, txw); |
| dws->tx += dws->n_bytes; |
| } |
| } |
| |
| static void dw_reader(struct dw_spi *dws) |
| { |
| u32 max = rx_max(dws); |
| u16 rxw; |
| |
| while (max--) { |
| rxw = dw_readw(dws, DW_SPI_DR); |
| /* Care rx only if the transfer's original "rx" is not null */ |
| if (dws->rx_end - dws->len) { |
| if (dws->n_bytes == 1) |
| *(u8 *)(dws->rx) = rxw; |
| else |
| *(u16 *)(dws->rx) = rxw; |
| } |
| dws->rx += dws->n_bytes; |
| } |
| } |
| |
| static void *next_transfer(struct dw_spi *dws) |
| { |
| struct spi_message *msg = dws->cur_msg; |
| struct spi_transfer *trans = dws->cur_transfer; |
| |
| /* Move to next transfer */ |
| if (trans->transfer_list.next != &msg->transfers) { |
| dws->cur_transfer = |
| list_entry(trans->transfer_list.next, |
| struct spi_transfer, |
| transfer_list); |
| return RUNNING_STATE; |
| } else |
| return DONE_STATE; |
| } |
| |
| /* |
| * Note: first step is the protocol driver prepares |
| * a dma-capable memory, and this func just need translate |
| * the virt addr to physical |
| */ |
| static int map_dma_buffers(struct dw_spi *dws) |
| { |
| if (!dws->cur_msg->is_dma_mapped |
| || !dws->dma_inited |
| || !dws->cur_chip->enable_dma |
| || !dws->dma_ops) |
| return 0; |
| |
| if (dws->cur_transfer->tx_dma) |
| dws->tx_dma = dws->cur_transfer->tx_dma; |
| |
| if (dws->cur_transfer->rx_dma) |
| dws->rx_dma = dws->cur_transfer->rx_dma; |
| |
| return 1; |
| } |
| |
| /* Caller already set message->status; dma and pio irqs are blocked */ |
| static void giveback(struct dw_spi *dws) |
| { |
| struct spi_transfer *last_transfer; |
| unsigned long flags; |
| struct spi_message *msg; |
| |
| spin_lock_irqsave(&dws->lock, flags); |
| msg = dws->cur_msg; |
| dws->cur_msg = NULL; |
| dws->cur_transfer = NULL; |
| dws->prev_chip = dws->cur_chip; |
| dws->cur_chip = NULL; |
| dws->dma_mapped = 0; |
| queue_work(dws->workqueue, &dws->pump_messages); |
| spin_unlock_irqrestore(&dws->lock, flags); |
| |
| last_transfer = list_entry(msg->transfers.prev, |
| struct spi_transfer, |
| transfer_list); |
| |
| if (!last_transfer->cs_change && dws->cs_control) |
| dws->cs_control(MRST_SPI_DEASSERT); |
| |
| msg->state = NULL; |
| if (msg->complete) |
| msg->complete(msg->context); |
| } |
| |
| static void int_error_stop(struct dw_spi *dws, const char *msg) |
| { |
| /* Stop the hw */ |
| spi_enable_chip(dws, 0); |
| |
| dev_err(&dws->master->dev, "%s\n", msg); |
| dws->cur_msg->state = ERROR_STATE; |
| tasklet_schedule(&dws->pump_transfers); |
| } |
| |
| void dw_spi_xfer_done(struct dw_spi *dws) |
| { |
| /* Update total byte transferred return count actual bytes read */ |
| dws->cur_msg->actual_length += dws->len; |
| |
| /* Move to next transfer */ |
| dws->cur_msg->state = next_transfer(dws); |
| |
| /* Handle end of message */ |
| if (dws->cur_msg->state == DONE_STATE) { |
| dws->cur_msg->status = 0; |
| giveback(dws); |
| } else |
| tasklet_schedule(&dws->pump_transfers); |
| } |
| EXPORT_SYMBOL_GPL(dw_spi_xfer_done); |
| |
| static irqreturn_t interrupt_transfer(struct dw_spi *dws) |
| { |
| u16 irq_status = dw_readw(dws, DW_SPI_ISR); |
| |
| /* Error handling */ |
| if (irq_status & (SPI_INT_TXOI | SPI_INT_RXOI | SPI_INT_RXUI)) { |
| dw_readw(dws, DW_SPI_TXOICR); |
| dw_readw(dws, DW_SPI_RXOICR); |
| dw_readw(dws, DW_SPI_RXUICR); |
| int_error_stop(dws, "interrupt_transfer: fifo overrun/underrun"); |
| return IRQ_HANDLED; |
| } |
| |
| dw_reader(dws); |
| if (dws->rx_end == dws->rx) { |
| spi_mask_intr(dws, SPI_INT_TXEI); |
| dw_spi_xfer_done(dws); |
| return IRQ_HANDLED; |
| } |
| if (irq_status & SPI_INT_TXEI) { |
| spi_mask_intr(dws, SPI_INT_TXEI); |
| dw_writer(dws); |
| /* Enable TX irq always, it will be disabled when RX finished */ |
| spi_umask_intr(dws, SPI_INT_TXEI); |
| } |
| |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t dw_spi_irq(int irq, void *dev_id) |
| { |
| struct dw_spi *dws = dev_id; |
| u16 irq_status = dw_readw(dws, DW_SPI_ISR) & 0x3f; |
| |
| if (!irq_status) |
| return IRQ_NONE; |
| |
| if (!dws->cur_msg) { |
| spi_mask_intr(dws, SPI_INT_TXEI); |
| return IRQ_HANDLED; |
| } |
| |
| return dws->transfer_handler(dws); |
| } |
| |
| /* Must be called inside pump_transfers() */ |
| static void poll_transfer(struct dw_spi *dws) |
| { |
| do { |
| dw_writer(dws); |
| dw_reader(dws); |
| cpu_relax(); |
| } while (dws->rx_end > dws->rx); |
| |
| dw_spi_xfer_done(dws); |
| } |
| |
| static void pump_transfers(unsigned long data) |
| { |
| struct dw_spi *dws = (struct dw_spi *)data; |
| struct spi_message *message = NULL; |
| struct spi_transfer *transfer = NULL; |
| struct spi_transfer *previous = NULL; |
| struct spi_device *spi = NULL; |
| struct chip_data *chip = NULL; |
| u8 bits = 0; |
| u8 imask = 0; |
| u8 cs_change = 0; |
| u16 txint_level = 0; |
| u16 clk_div = 0; |
| u32 speed = 0; |
| u32 cr0 = 0; |
| |
| #ifdef CONFIG_C2K_DEVFREQ_DW |
| devfreq_func_start(&dc); |
| #endif |
| |
| /* Get current state information */ |
| message = dws->cur_msg; |
| transfer = dws->cur_transfer; |
| chip = dws->cur_chip; |
| spi = message->spi; |
| |
| if (unlikely(!chip->clk_div)) |
| chip->clk_div = dws->max_freq / chip->speed_hz; |
| |
| if (message->state == ERROR_STATE) { |
| message->status = -EIO; |
| goto early_exit; |
| } |
| |
| /* Handle end of message */ |
| if (message->state == DONE_STATE) { |
| message->status = 0; |
| goto early_exit; |
| } |
| |
| /* Delay if requested at end of transfer*/ |
| if (message->state == RUNNING_STATE) { |
| previous = list_entry(transfer->transfer_list.prev, |
| struct spi_transfer, |
| transfer_list); |
| if (previous->delay_usecs) |
| udelay(previous->delay_usecs); |
| } |
| |
| dws->n_bytes = chip->n_bytes; |
| dws->dma_width = chip->dma_width; |
| dws->cs_control = chip->cs_control; |
| |
| dws->rx_dma = transfer->rx_dma; |
| dws->tx_dma = transfer->tx_dma; |
| dws->tx = (void *)transfer->tx_buf; |
| dws->tx_end = dws->tx + transfer->len; |
| dws->rx = transfer->rx_buf; |
| dws->rx_end = dws->rx + transfer->len; |
| dws->cs_change = transfer->cs_change; |
| dws->len = dws->cur_transfer->len; |
| if (chip != dws->prev_chip) |
| cs_change = 1; |
| |
| cr0 = chip->cr0; |
| |
| /* Handle per transfer options for bpw and speed */ |
| if (transfer->speed_hz) { |
| speed = chip->speed_hz; |
| |
| if (transfer->speed_hz != speed) { |
| speed = transfer->speed_hz; |
| if (speed > dws->max_freq) { |
| printk(KERN_ERR "MRST SPI0: unsupported" |
| "freq: %dHz\n", speed); |
| message->status = -EIO; |
| goto early_exit; |
| } |
| |
| /* clk_div doesn't support odd number */ |
| clk_div = dws->max_freq / speed; |
| clk_div = (clk_div + 1) & 0xfffe; |
| |
| chip->speed_hz = speed; |
| chip->clk_div = clk_div; |
| } |
| } |
| if (transfer->bits_per_word) { |
| bits = transfer->bits_per_word; |
| |
| switch (bits) { |
| case 8: |
| case 16: |
| dws->n_bytes = dws->dma_width = bits >> 3; |
| break; |
| default: |
| printk(KERN_ERR "MRST SPI0: unsupported bits:" |
| "%db\n", bits); |
| message->status = -EIO; |
| goto early_exit; |
| } |
| |
| cr0 = (bits - 1) |
| | (chip->type << SPI_FRF_OFFSET) |
| | (spi->mode << SPI_MODE_OFFSET) |
| | (chip->tmode << SPI_TMOD_OFFSET); |
| } |
| message->state = RUNNING_STATE; |
| |
| /* |
| * Adjust transfer mode if necessary. Requires platform dependent |
| * chipselect mechanism. |
| */ |
| if (dws->cs_control) { |
| if (dws->rx && dws->tx) |
| chip->tmode = SPI_TMOD_TR; |
| else if (dws->rx) |
| chip->tmode = SPI_TMOD_RO; |
| else |
| chip->tmode = SPI_TMOD_TO; |
| |
| cr0 &= ~SPI_TMOD_MASK; |
| cr0 |= (chip->tmode << SPI_TMOD_OFFSET); |
| } |
| |
| /* Check if current transfer is a DMA transaction */ |
| dws->dma_mapped = map_dma_buffers(dws); |
| |
| /* |
| * Interrupt mode |
| * we only need set the TXEI IRQ, as TX/RX always happen syncronizely |
| */ |
| if (!dws->dma_mapped && !chip->poll_mode) { |
| int templen = dws->len / dws->n_bytes; |
| txint_level = dws->fifo_len / 2; |
| txint_level = (templen > txint_level) ? txint_level : templen; |
| |
| imask |= SPI_INT_TXEI | SPI_INT_TXOI | SPI_INT_RXUI | SPI_INT_RXOI; |
| dws->transfer_handler = interrupt_transfer; |
| } |
| |
| /* |
| * Reprogram registers only if |
| * 1. chip select changes |
| * 2. clk_div is changed |
| * 3. control value changes |
| */ |
| if (dw_readw(dws, DW_SPI_CTRL0) != cr0 || cs_change || clk_div || imask) { |
| spi_enable_chip(dws, 0); |
| |
| if (dw_readw(dws, DW_SPI_CTRL0) != cr0) |
| dw_writew(dws, DW_SPI_CTRL0, cr0); |
| |
| spi_set_clk(dws, clk_div ? clk_div : chip->clk_div); |
| spi_chip_sel(dws, spi->chip_select); |
| |
| /* Set the interrupt mask, for poll mode just disable all int */ |
| spi_mask_intr(dws, 0xff); |
| if (imask) |
| spi_umask_intr(dws, imask); |
| if (txint_level) |
| dw_writew(dws, DW_SPI_TXFLTR, txint_level); |
| |
| spi_enable_chip(dws, 1); |
| if (cs_change) |
| dws->prev_chip = chip; |
| } |
| |
| if (dws->dma_mapped) |
| dws->dma_ops->dma_transfer(dws, cs_change); |
| |
| if (chip->poll_mode) |
| poll_transfer(dws); |
| |
| #ifdef CONFIG_C2K_DEVFREQ_DW |
| devfreq_func_end(&dc); |
| #endif |
| |
| return; |
| |
| early_exit: |
| giveback(dws); |
| return; |
| } |
| |
| static void pump_messages(struct work_struct *work) |
| { |
| struct dw_spi *dws = |
| container_of(work, struct dw_spi, pump_messages); |
| unsigned long flags; |
| |
| /* Lock queue and check for queue work */ |
| spin_lock_irqsave(&dws->lock, flags); |
| if (list_empty(&dws->queue) || dws->run == QUEUE_STOPPED) { |
| dws->busy = 0; |
| spin_unlock_irqrestore(&dws->lock, flags); |
| return; |
| } |
| |
| /* Make sure we are not already running a message */ |
| if (dws->cur_msg) { |
| spin_unlock_irqrestore(&dws->lock, flags); |
| return; |
| } |
| |
| /* Extract head of queue */ |
| dws->cur_msg = list_entry(dws->queue.next, struct spi_message, queue); |
| list_del_init(&dws->cur_msg->queue); |
| |
| /* Initial message state*/ |
| dws->cur_msg->state = START_STATE; |
| dws->cur_transfer = list_entry(dws->cur_msg->transfers.next, |
| struct spi_transfer, |
| transfer_list); |
| dws->cur_chip = spi_get_ctldata(dws->cur_msg->spi); |
| |
| /* Mark as busy and launch transfers */ |
| tasklet_schedule(&dws->pump_transfers); |
| |
| dws->busy = 1; |
| spin_unlock_irqrestore(&dws->lock, flags); |
| } |
| |
| /* spi_device use this to queue in their spi_msg */ |
| static int dw_spi_transfer(struct spi_device *spi, struct spi_message *msg) |
| { |
| struct dw_spi *dws = spi_master_get_devdata(spi->master); |
| unsigned long flags; |
| #ifdef CONFIG_C2K_DEVFREQ_DW |
| devfreq_func_start(&dc); |
| #endif |
| |
| spin_lock_irqsave(&dws->lock, flags); |
| |
| if (dws->run == QUEUE_STOPPED) { |
| spin_unlock_irqrestore(&dws->lock, flags); |
| return -ESHUTDOWN; |
| } |
| |
| msg->actual_length = 0; |
| msg->status = -EINPROGRESS; |
| msg->state = START_STATE; |
| |
| list_add_tail(&msg->queue, &dws->queue); |
| |
| if (dws->run == QUEUE_RUNNING && !dws->busy) { |
| |
| if (dws->cur_transfer || dws->cur_msg) |
| queue_work(dws->workqueue, |
| &dws->pump_messages); |
| else { |
| /* If no other data transaction in air, just go */ |
| spin_unlock_irqrestore(&dws->lock, flags); |
| pump_messages(&dws->pump_messages); |
| return 0; |
| } |
| } |
| |
| spin_unlock_irqrestore(&dws->lock, flags); |
| #ifdef CONFIG_C2K_DEVFREQ_DW |
| devfreq_func_end(&dc); |
| #endif |
| return 0; |
| } |
| |
| /* This may be called twice for each spi dev */ |
| static int dw_spi_setup(struct spi_device *spi) |
| { |
| struct dw_spi_chip *chip_info = NULL; |
| struct chip_data *chip; |
| |
| if (spi->bits_per_word != 8 && spi->bits_per_word != 16) |
| return -EINVAL; |
| |
| /* Only alloc on first setup */ |
| chip = spi_get_ctldata(spi); |
| if (!chip) { |
| chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL); |
| if (!chip) |
| return -ENOMEM; |
| } |
| |
| /* |
| * Protocol drivers may change the chip settings, so... |
| * if chip_info exists, use it |
| */ |
| chip_info = spi->controller_data; |
| |
| /* chip_info doesn't always exist */ |
| if (chip_info) { |
| if (chip_info->cs_control) |
| chip->cs_control = chip_info->cs_control; |
| |
| chip->poll_mode = chip_info->poll_mode; |
| chip->type = chip_info->type; |
| |
| chip->rx_threshold = 0; |
| chip->tx_threshold = 0; |
| |
| chip->enable_dma = chip_info->enable_dma; |
| } |
| |
| if (spi->bits_per_word <= 8) { |
| chip->n_bytes = 1; |
| chip->dma_width = 1; |
| } else if (spi->bits_per_word <= 16) { |
| chip->n_bytes = 2; |
| chip->dma_width = 2; |
| } else { |
| /* Never take >16b case for MRST SPIC */ |
| dev_err(&spi->dev, "invalid wordsize\n"); |
| return -EINVAL; |
| } |
| chip->bits_per_word = spi->bits_per_word; |
| |
| if (!spi->max_speed_hz) { |
| dev_err(&spi->dev, "No max speed HZ parameter\n"); |
| return -EINVAL; |
| } |
| chip->speed_hz = spi->max_speed_hz; |
| |
| chip->tmode = 0; /* Tx & Rx */ |
| /* Default SPI mode is SCPOL = 0, SCPH = 0 */ |
| chip->cr0 = (chip->bits_per_word - 1) |
| | (chip->type << SPI_FRF_OFFSET) |
| | (spi->mode << SPI_MODE_OFFSET) |
| | (chip->tmode << SPI_TMOD_OFFSET); |
| |
| spi_set_ctldata(spi, chip); |
| return 0; |
| } |
| |
| static void dw_spi_cleanup(struct spi_device *spi) |
| { |
| struct chip_data *chip = spi_get_ctldata(spi); |
| kfree(chip); |
| } |
| |
| static int __devinit init_queue(struct dw_spi *dws) |
| { |
| INIT_LIST_HEAD(&dws->queue); |
| spin_lock_init(&dws->lock); |
| |
| dws->run = QUEUE_STOPPED; |
| dws->busy = 0; |
| |
| tasklet_init(&dws->pump_transfers, |
| pump_transfers, (unsigned long)dws); |
| |
| INIT_WORK(&dws->pump_messages, pump_messages); |
| dws->workqueue = create_singlethread_workqueue( |
| dev_name(dws->master->dev.parent)); |
| if (dws->workqueue == NULL) |
| return -EBUSY; |
| |
| return 0; |
| } |
| |
| static int start_queue(struct dw_spi *dws) |
| { |
| unsigned long flags; |
| |
| spin_lock_irqsave(&dws->lock, flags); |
| |
| if (dws->run == QUEUE_RUNNING || dws->busy) { |
| spin_unlock_irqrestore(&dws->lock, flags); |
| return -EBUSY; |
| } |
| |
| dws->run = QUEUE_RUNNING; |
| dws->cur_msg = NULL; |
| dws->cur_transfer = NULL; |
| dws->cur_chip = NULL; |
| dws->prev_chip = NULL; |
| spin_unlock_irqrestore(&dws->lock, flags); |
| |
| queue_work(dws->workqueue, &dws->pump_messages); |
| |
| return 0; |
| } |
| |
| static int stop_queue(struct dw_spi *dws) |
| { |
| unsigned long flags; |
| unsigned limit = 50; |
| int status = 0; |
| |
| spin_lock_irqsave(&dws->lock, flags); |
| dws->run = QUEUE_STOPPED; |
| while ((!list_empty(&dws->queue) || dws->busy) && limit--) { |
| spin_unlock_irqrestore(&dws->lock, flags); |
| msleep(10); |
| spin_lock_irqsave(&dws->lock, flags); |
| } |
| |
| if (!list_empty(&dws->queue) || dws->busy) |
| status = -EBUSY; |
| spin_unlock_irqrestore(&dws->lock, flags); |
| |
| return status; |
| } |
| |
| static int destroy_queue(struct dw_spi *dws) |
| { |
| int status; |
| |
| status = stop_queue(dws); |
| if (status != 0) |
| return status; |
| destroy_workqueue(dws->workqueue); |
| return 0; |
| } |
| |
| /* Restart the controller, disable all interrupts, clean rx fifo */ |
| static void spi_hw_init(struct dw_spi *dws) |
| { |
| spi_enable_chip(dws, 0); |
| spi_mask_intr(dws, 0xff); |
| spi_enable_chip(dws, 1); |
| |
| /* |
| * Try to detect the FIFO depth if not set by interface driver, |
| * the depth could be from 2 to 256 from HW spec |
| */ |
| if (!dws->fifo_len) { |
| u32 fifo; |
| for (fifo = 2; fifo <= 257; fifo++) { |
| dw_writew(dws, DW_SPI_TXFLTR, fifo); |
| if (fifo != dw_readw(dws, DW_SPI_TXFLTR)) |
| break; |
| } |
| |
| dws->fifo_len = (fifo == 257) ? 0 : fifo; |
| dw_writew(dws, DW_SPI_TXFLTR, 0); |
| } |
| } |
| |
| #ifdef CONFIG_C2K_DEVFREQ_DW |
| #define SPI_MAXFREQ_MHZ 2000000 |
| #define SPI_MINFREQ_MHZ 1000000 |
| #define POLLING_MS 1000 |
| #define OPP_TABLE_SIZE 4 |
| |
| struct devfreq_dev_profile spi_devfreq_profile; |
| struct c2k_devfreq_data devfreq_spi_data; |
| static struct c2k_devfreq_opp_table spi_opp_tbl[OPP_TABLE_SIZE]; |
| |
| /* |
| * intialize OPP table, profile data (initial freq, polling interval), |
| * max/min freq supported by SPI controller. |
| */ |
| static void init_spi_devfreq_data(struct dw_spi *dws) |
| { |
| int i = 0; |
| struct c2k_devfreq_opp_table opp_tbl[OPP_TABLE_SIZE] = { |
| {1, 1000000, 0}, |
| {2, 2000000, 0}, |
| {3, 4000000, 0}, |
| {0, 0, 0}, |
| }; |
| |
| while (i < sizeof(opp_tbl)) |
| { |
| spi_opp_tbl[i].idx = opp_tbl[i].idx; |
| spi_opp_tbl[i].freq = opp_tbl[i].freq; |
| spi_opp_tbl[i].volt = opp_tbl[i].volt; |
| i++; |
| } |
| |
| spi_devfreq_profile.initial_freq = dws->max_freq; |
| spi_devfreq_profile.polling_ms = POLLING_MS; |
| |
| devfreq_spi_data.devfreq_profile = &spi_devfreq_profile; |
| devfreq_spi_data.opp_table = &spi_opp_tbl[0]; |
| devfreq_spi_data.set_freq = set_spi_freq; |
| devfreq_spi_data.max_freq = SPI_MAXFREQ_MHZ; |
| devfreq_spi_data.min_freq = SPI_MINFREQ_MHZ; |
| } |
| #endif |
| |
| int __devinit dw_spi_add_host(struct dw_spi *dws) |
| { |
| struct spi_master *master; |
| int ret; |
| |
| BUG_ON(dws == NULL); |
| |
| master = spi_alloc_master(dws->parent_dev, 0); |
| if (!master) { |
| ret = -ENOMEM; |
| goto exit; |
| } |
| |
| clk_enable(dws->clk_spi); |
| |
| dws->master = master; |
| dws->type = SSI_MOTO_SPI; |
| dws->prev_chip = NULL; |
| dws->dma_inited = 0; |
| dws->dma_addr = (dma_addr_t)(dws->paddr + 0x60); |
| snprintf(dws->name, sizeof(dws->name), "dw_spi%d", |
| dws->bus_num); |
| |
| ret = request_irq(dws->irq, dw_spi_irq, IRQF_SHARED, |
| dws->name, dws); |
| if (ret < 0) { |
| dev_err(&master->dev, "can not get IRQ\n"); |
| goto err_free_master; |
| } |
| |
| master->mode_bits = SPI_CPOL | SPI_CPHA; |
| master->bus_num = dws->bus_num; |
| master->num_chipselect = dws->num_cs; |
| master->cleanup = dw_spi_cleanup; |
| master->setup = dw_spi_setup; |
| master->transfer = dw_spi_transfer; |
| |
| /* Basic HW init */ |
| spi_hw_init(dws); |
| |
| if (dws->dma_ops && dws->dma_ops->dma_init) { |
| ret = dws->dma_ops->dma_init(dws); |
| if (ret) { |
| dev_warn(&master->dev, "DMA init failed\n"); |
| dws->dma_inited = 0; |
| } |
| } |
| |
| /* Initial and start queue */ |
| ret = init_queue(dws); |
| if (ret) { |
| dev_err(&master->dev, "problem initializing queue\n"); |
| goto err_diable_hw; |
| } |
| ret = start_queue(dws); |
| if (ret) { |
| dev_err(&master->dev, "problem starting queue\n"); |
| goto err_diable_hw; |
| } |
| |
| spi_master_set_devdata(master, dws); |
| ret = spi_register_master(master); |
| if (ret) { |
| dev_err(&master->dev, "problem registering spi master\n"); |
| goto err_queue_alloc; |
| } |
| |
| mrst_spi_debugfs_init(dws); |
| |
| #ifdef CONFIG_C2K_DEVFREQ_DW |
| init_spi_devfreq_data(dws); |
| |
| ret = c2k_driver_devfreq(&master->dev, &devfreq_spi_data); |
| if(ret < 0) |
| goto err_queue_alloc; |
| #endif |
| return 0; |
| |
| err_queue_alloc: |
| destroy_queue(dws); |
| if (dws->dma_ops && dws->dma_ops->dma_exit) |
| dws->dma_ops->dma_exit(dws); |
| err_diable_hw: |
| spi_enable_chip(dws, 0); |
| free_irq(dws->irq, dws); |
| err_free_master: |
| clk_disable(dws->clk_spi); |
| spi_master_put(master); |
| exit: |
| return ret; |
| } |
| EXPORT_SYMBOL_GPL(dw_spi_add_host); |
| |
| void __devexit dw_spi_remove_host(struct dw_spi *dws) |
| { |
| int status = 0; |
| |
| if (!dws) |
| return; |
| mrst_spi_debugfs_remove(dws); |
| |
| /* Remove the queue */ |
| status = destroy_queue(dws); |
| if (status != 0) |
| dev_err(&dws->master->dev, "dw_spi_remove: workqueue will not " |
| "complete, message memory not freed\n"); |
| |
| if (dws->dma_ops && dws->dma_ops->dma_exit) |
| dws->dma_ops->dma_exit(dws); |
| spi_enable_chip(dws, 0); |
| free_irq(dws->irq, dws); |
| |
| /* Disconnect from the SPI framework */ |
| spi_unregister_master(dws->master); |
| /* Disable clk */ |
| clk_disable(dws->clk_spi); |
| } |
| EXPORT_SYMBOL_GPL(dw_spi_remove_host); |
| |
| int dw_spi_suspend_host(struct dw_spi *dws) |
| { |
| int ret = 0; |
| |
| ret = stop_queue(dws); |
| if (ret) |
| return ret; |
| spi_enable_chip(dws, 0); |
| |
| clk_disable(dws->clk_spi); |
| |
| return ret; |
| } |
| EXPORT_SYMBOL_GPL(dw_spi_suspend_host); |
| |
| int dw_spi_resume_host(struct dw_spi *dws) |
| { |
| int ret; |
| |
| clk_enable(dws->clk_spi); |
| spi_hw_init(dws); |
| ret = start_queue(dws); |
| if (ret) |
| dev_err(&dws->master->dev, "fail to start queue (%d)\n", ret); |
| return ret; |
| } |
| EXPORT_SYMBOL_GPL(dw_spi_resume_host); |
| |
| MODULE_AUTHOR("Feng Tang <feng.tang@intel.com>"); |
| MODULE_DESCRIPTION("Driver for DesignWare SPI controller core"); |
| MODULE_LICENSE("GPL v2"); |