| .\" vim:tw=78: |
| .\" Copyright (c) 1999-2003 Agere Systems Inc. -- http://www.agere.com |
| .\" wlags49.4 7.20-abg 04/28/2004 13:30:00 |
| .\" |
| .TH WLAGS49 4 "04/28/2004 13:30:00" "pcmcia-cs" |
| .SH NAME |
| wlags49 \- Agere Systems Wireless PC Card / PCI device drivers |
| |
| wlags49_h2_cs.o \- Hermes-II Card Services (PCMCIA/CF) driver |
| .br |
| wlags49_h2.o \- Hermes-II MiniPCI driver |
| .br |
| wlags49_h25.o \- Hermes-II.5 PCI/CardBus driver |
| .br |
| wlags49_h25_cs.o\- Hermes-II.5 Card Services (PCMCIA/CF) driver |
| |
| .SH SYNOPSIS |
| .nh |
| .fi |
| .B insmod wlags49_[h1,h2]_[cs].o |
| .br |
| .RB [ Authentication=n ] |
| .RB [ AuthKeyMngmtSuite=???? ] |
| .RB [ BRSC2GHz=b ]\p |
| .RB [ BRSC5GHz=b ] |
| .RB [ Coexistence=n ] |
| .RB [ Configured=???? ]\p |
| .RB [ ConnectionControl=???? ] |
| .RB [ CreateIBSS=s ] |
| .RB [ DebugFlag=n ]\p |
| .RB [ DesiredSSID=s ] |
| .RB [ DownloadFirmware=n ] |
| .RB [ DriverEnable=???? ]\p |
| .RB [ EnableEncryption=s ] |
| .RB [ Encryption=???? ] |
| .RB [ ExcludeUnencrypted=s ]\p |
| .RB [ IntraBSSRelay=s ] |
| .RB [ IrqList=i,j,... ] |
| .RB [ IrqMask=n ]\p |
| .RB [ Key1=s ] |
| .RB [ Key2=s ] |
| .RB [ Key3=s ] |
| .RB [ Key4=s ]\p |
| .RB [ LoadBalancing=s ] |
| .RB [ MaxSleepDuration=n ] |
| .RB [ MediumDistribution=s ]\p |
| .RB [ MicroWaveRobustness=s ] |
| .RB [ MulticastPMBuffering=s ] |
| .RB [ MulticastRate=n ]\p |
| .RB [ MulticastReceive=s ] |
| .RB [ NetworkAddress=n,n,n,n,n,n ] |
| .RB [ NetworkType=???? ]\p |
| .RB [ OwnATIMWindow=n ] |
| .RB [ OwnBeaconInterval=n ] |
| .RB [ OwnChannel=n ]\p |
| .RB [ OwnDTIMPeriod=n ] |
| .RB [ OwnName=s ] |
| .RB [ OwnSSID=s ]\p |
| .RB [ pc_debug=n ] |
| .RB [ PMEnabled=b ] |
| .RB [ PMHoldoverDuration=n ]\p |
| .RB [ PortType=n ] |
| .RB [ PowerMode=???? ] |
| .RB [ PromiscuousMode=s ]\p |
| .RB [ RejectANY=s ] |
| .RB [ RTSThreshold=n ]\p |
| .RB [ RTSThreshold1=n ] |
| .RB [ RTSThreshold2=n ] |
| .RB [ RTSThreshold3=n ]\p |
| .RB [ RTSThreshold4=n ] |
| .RB [ RTSThreshold5=n ] |
| .RB [ RTSThreshold6=n ]\p |
| .RB [ SRSC2GHz=b ] |
| .RB [ SRSC5GHz=b ] |
| .RB [ SystemScale=n ]\p |
| .RB [ TxKey=n ] |
| .RB [ TxRateControl=n ]\p |
| .RB [ TxRateControl1=n ] |
| .RB [ TxRateControl2=n ] |
| .RB [ TxRateControl3=n ]\p |
| .RB [ TxRateControl4=n ] |
| .RB [ TxRateControl5=n ] |
| .RB [ TxRateControl6=n ]\p |
| .RB [ WDSAddress=n,n,n,n,n,n ]\p |
| .RB [ WDSAddress1=n,n,n,n,n,n ] |
| .RB [ WDSAddress2=n,n,n,n,n,n ]\p |
| .RB [ WDSAddress3=n,n,n,n,n,n ] |
| .RB [ WDSAddress4=n,n,n,n,n,n ]\p |
| .RB [ WDSAddress5=n,n,n,n,n,n ] |
| .RB [ WDSAddress6=n,n,n,n,n,n ]\p |
| .fi |
| |
| |
| |
| .SH DESCRIPTION |
| .I wlags49 |
| is the low-level Card Services / PCI driver for the |
| .B Wireless PC Card, Wireless Integrated Card, Wireless Embedded Card |
| and other wireless adapters based on the Agere Systems Hermes-II, and Hermes-II.5 wireless MAC. When this driver is attached to a card, it |
| allocates the next available ethernet device (eth0..eth#). This |
| device name will be passed on to |
| .IR cardmgr (8), |
| or the PCI subsystem, for the card configuration, and reported in the kernel log file |
| with the I/O base address and MAC address used by the card. |
| .SH FEATURES |
| \- Hot plug/unplug |
| \- Access Point and peer-to-peer communication |
| \- Card power management |
| \- Support for Hermes-II & Hermes-II.5 based PCMCIA, Mini PCI, and CardBus cards |
| \- Wired Equivalent Privacy (WEP) |
| \- WPA-PSK support (EXPERIMENTAL) |
| \- Driver utility interface (UIL) |
| \- Wireless Extensions |
| \- Software AP mode |
| .SH PARAMETERS |
| .TP |
| .B Authentication=n |
| Algorithm used for Authentication. |
| .BR |
| 1 \- Open System |
| .BR |
| 2 \- Shared Key |
| .BR |
| Default: 1 |
| .TP |
| .B Auth_key_mgmt_suite |
| ??????????????? |
| .TP |
| .B BRSC2GHz=b |
| Sets the card\'s Basic Rate Set in the 2.4GHz band. See SRSC2GHz |
| for the value\'s format. |
| .BR |
| Default: 15 (or 0x000F, only 11b rates to accept legacy 11b stations) |
| .TP |
| .B BRSC5GHz-b |
| Sets the card\'s Basic Rate Set in the 5.0GHz band. See SRSC2GHz for the |
| value\'s format |
| .BR |
| Default: 4080 (or 0x0FF0, all 11a rates) |
| .TP |
| .B Coexistence=n |
| Used to make the 802.11a/b/g coexistence behavior more strict. |
| .BR |
| Default \- 0 (Use standard behavior) |
| .TP |
| .B ConnectionControl=n |
| Configures the card\'s connection control process in dealing with multiple |
| bands (802.11b/g vs. 802.11a). |
| .BR |
| 0 \- Single Band operation in 2GHz |
| .BR |
| 1 \- Single Band operation in 5GHz |
| .BR |
| 2 \- Multiple Band operation starting with 2GHz |
| .BR |
| 3 \- Multiple Band operation starting with 5GHz |
| .BR |
| Default \- 2 |
| .TP |
| .B Configured |
| ??????????????? |
| .TP |
| .B ConnectionControl |
| ??????????????? |
| .TP |
| .B CreateIBSS=s |
| Enable or disable IBSS Creation. |
| For correct operation, specification of a OwnSSID is required. |
| This mode requires firmware 6.04 or higher. |
| .BR |
| N \- Disable |
| .BR |
| Y \- Enable |
| .BR |
| Default: N |
| .TP |
| .B DebugFlag=n |
| Selects the driver debugging level. This parameter is only available |
| if the module is compiled with debugging enabled. Refer to the |
| file |
| .B debug.h |
| in the source directory for information on the flag values. |
| .BR |
| 0x00000001L \- DBG_ERROR_ON |
| .BR |
| 0x00000002L \- DBG_WARNING_ON |
| .BR |
| 0x00000004L \- DBG_NOTICE_ON |
| .BR |
| 0x00000008L \- DBG_TRACE_ON |
| .BR |
| 0x00000010L \- DBG_VERBOSE_ON |
| .BR |
| 0x00000020L \- DBG_PARAM_ON |
| .BR |
| 0x00000040L \- DBG_BREAK_ON |
| .BR |
| 0x00000100L \- DBG_RX_ON |
| .BR |
| 0x00000200L \- DBG_TX_ON |
| .BR |
| 0x00000400L \- DBG_DS_ON |
| .BR |
| If the module is compiled with debugging enabled, DebugFlag |
| defaults to DBG_ERROR_ON, DBG_WARNING_ON and DBG_BREAK_ON. |
| DebugFlag overrules pc_debug. |
| .TP |
| .B DesiredSSID=s |
| Same as OwnSSID. |
| .TP |
| .B DownloadFirmware=n |
| This release of the driver introduces the ability to perform downloads of the STA/AP |
| firmware. In fact, this is required for Hermes-II based cards. This parameter tells |
| the driver which version of the firmware to download to the card. |
| .BR |
| 0 \- No download performed (Hermes-I only) |
| .BR |
| 1 \- Download STA firmware |
| .BR |
| 2 \- Download AP firmware |
| .BR |
| Default: 1, when STA mode functionality is |
| included in the build |
| 2, when code is built exclusively for |
| AP mode |
| .TP |
| .B DriverEnable |
| ??????????????? |
| .TP |
| .B EnableEncryption=n |
| Set the method of Data encryption. |
| .BR |
| 0 \- Disable |
| .BR |
| 1 \- Enable WEP Encryption |
| .BR |
| 2 \- Enable WPA with TKIP encryption |
| .BR |
| Default: 0 |
| .TP |
| .B Encryption |
| ??????????????? |
| .TP |
| .B ExcludeUnencrypted=s |
| Controls how the stations must communicate with the AP. |
| .BR |
| Y \- Stations must enable encryption and provide |
| the proper encryption key to communicate |
| with the AP. |
| .BR |
| N \- Stations do not need to enable encryption |
| to communicate with the AP. |
| .BR |
| Default: N |
| .TP |
| .B IntraBSSRelay=s |
| Controls the automatic relay of received messages that are destined for other |
| stations in the BSS. |
| .BR |
| Y \- Messages are relayed to the appropriate |
| station(s). |
| .BR |
| N \- Messages are passed up to the host. |
| .BR |
| Default: Y |
| .TP |
| .B IrqList=i,j,... |
| Specifies the set of interrupts (up to 4) that may be allocated by |
| this driver. This overrides the values set in the |
| .B IrqMask |
| parameter. NOTE: This parameter is for PCMCIA only. |
| .TP |
| .B IrqMask=n |
| Specifies a mask of valid interrupts that may be allocated by this driver. |
| If |
| .B IrqList |
| is also specified, the values in |
| .B IrqList |
| are used instead. NOTE: This parameter is for PCMCIA only. |
| .BR |
| Default: 0xdeb8 (IRQ 3,4,5,7,9,10,11,12,14,15) |
| .TP |
| .B Key1=s |
| Specifies one of 4 possible keys for the Data encryption. |
| One of these keys, identified by TxKey, |
| is used for the enciphering of Data that is transmitted by this station. |
| All keys specified can be used for the deciphering of Data that is received. |
| .BR |
| The key value can be an ASCII character string or a hexadecimal value. |
| The length of the key value can be 5 characters or 10 hexadecimal digits for |
| the standard encryption (Silver or Gold card), or 13 characters or 26 |
| hexadecimal digits for the encryption with extended keys (Gold card only). |
| The keys defined in the station must match the keys defined in the access |
| points; both on value and number (1 through 4). |
| .BR |
| In 2.0 series Linux kernel modules, values that begin with a number are |
| considered integers. In this case a hexadecimal value string or a character |
| string starting with a number, will need to be surrounded by escaped |
| double quotes (ie. Key1=\\"0x1122334455\\" Key2=\\"12xyz\\"). |
| .BR |
| 5 or 13, printable character string, or |
| .BR |
| 10 or 26 hex digits if preceded by "0x". |
| .BR |
| If this parameter is omitted, the default of the MAC is used ( = 0-length). |
| .TP |
| .B Key2=s |
| Same as Key1. |
| .TP |
| .B Key3=s |
| Same as Key1. |
| .TP |
| .B Key4=s |
| Same as Key1. |
| .TP |
| .B LoadBalancing=s |
| Control for the Load Balancing algorithm for both STAs and APs. The AP |
| includes a load balancing element in the Probe Response and Beacon frames. |
| The STA uses this info to select an AP, not only based on comms quality, but |
| also on the load of that AP. |
| .BR |
| Default: Y |
| .TP |
| .B MaxDataLength |
| ??????????????? |
| .TP |
| .B MaxSleepDuration=n |
| Set the maximum Power Management sleep duration in milliseconds. |
| Valid values are 0 to 65535 milliseconds. |
| .BR |
| Default: 100 |
| .TP |
| .B MediumDistribution=s |
| Control for the distribution of medium parameters, like communication |
| thresholds, microwave robustness, RTS/CTS thresholds, by APs. The associated |
| stations replace their own values with the received values. |
| .BR |
| Default=Y |
| .TP |
| .B MicroWaveRobustness=s |
| Enable or disable Microwave Oven Robustness. |
| .BR |
| N \- Disable |
| .BR |
| Y \- Enable |
| .BR |
| Default: N |
| .TP |
| .B MulticastPMBuffering=s |
| Controls buffering of multicast MAC frames for transmission after DTIM. If no, |
| multicast MAC frames are directly placed in the output queue. |
| .BR |
| Default: Y |
| .TP |
| .B MulticastRate=n |
| Sets the data rate for multicast message transmission. |
| .BR |
| 1 \- Fixed 1Mb/s |
| 2 \- Fixed 2Mb/s |
| 3 \- Fixed 5.5Mb/s |
| 4 \- Fixed 11Mb/s |
| .BR |
| Default: 2 |
| |
| For Hermes-II.5, an INTEGER CONVERTED bit mask representing the |
| rate to multicast, where the rates supported are as follows: |
| |
| Bit : 15|14|13|12|11|10|09|08|07|06|05|04|03|02|01|00 |
| .br |
| ------------------------------------------------------ |
| .br |
| Rate : XX|XX|XX|XX|54|48|36|24|18|12| 9| 6|11|5.5|2| 1 |
| |
| Default: 4 (Translates to 0x0004 = 5.5 Mb/sec) |
| |
| .TP |
| .B MulticastReceive=s |
| Enable or disable receiving of all multicast packets when Card Power Management |
| is enabled. When enabled, the station will wake up frequently |
| to receive the multicast frames. This causes less optimal power savings. |
| .BR |
| N \- Disable |
| .BR |
| Y \- Enable |
| .BR |
| Default: Y |
| .TP |
| .B NetworkAddress=n,n,n,n,n,n |
| Sets the adapter hardware ethernet address (MAC address) to the value |
| specified. Note that this is to be used to specify a Local MAC address. Do |
| not specify this parameter if the card\'s universal address is to be used. |
| Valid values are six hexadecimal digit-pairs (prefixed with 0x). |
| .BR |
| Default: <factory assigned address> |
| .TP |
| .B NetworkType |
| ??????????????? |
| .TP |
| .B OwnATIMWindow=n |
| ATIM window time used for creating an IBSS. |
| .BR |
| Range: 0..100 |
| .BR |
| Default: 0 |
| .TP |
| .B OwnBeaconInterval=b |
| Beacon Interval in TU |
| .BR |
| Range 20..200 |
| .BR |
| Default \- 100 |
| .TP |
| .B channel=n |
| Same as OwnChannel. |
| .TP |
| .B OwnChannel=n |
| Sets the channel the Ad-Hoc or IBSS mode will use. |
| The default channel for Ad-Hoc mode is determined by the Wireless PC Card. |
| The default channel for IBSS is set to 10 by the driver. |
| This value has no effect when the adapter is used with an Access Point |
| (BSS network) since the Access Point automatically determines the channel. |
| Valid values are 0 to 14. However the channels allowed in |
| your region are subject to local regulations and are limited at |
| manufacturing time of the Wireless PC Card. When the provided value is |
| not allowed, the value remains unchanged. |
| .BR |
| 0 \- Use default channel |
| .BR |
| Default: 0 |
| .TP |
| .B OwnDTIMPeriod=n |
| The number of beacon intervals between successive Delivery Traffic Identification |
| Maps (DTIMs). |
| .BR |
| Range: 1..65535 |
| .BR |
| Default: 1 |
| .TP |
| .B OwnName=s |
| Sets the station name to the specified string value. This parameter |
| is used for diagnostic purposes, as a user\-friendly identification |
| of this system. This parameter accepts a maximum of 32 characters. |
| .BR |
| Default: Linux |
| .TP |
| .B OwnSSID=s |
| Sets the card network name to the specified string value. This parameter |
| accepts a maximum of 32 characters. Whitespace in the network name |
| will need to be escaped with a backslash (ie. OwnSSID=My\\ Network). |
| .BR |
| Default: ANY |
| .TP |
| .B pc_debug=n |
| Selects the PCMCIA debugging level. This parameter is only available |
| if the module is compiled with debugging enabled. A non\-zero value |
| enables debugging. Higher values yield more information, i.e. for any value all |
| lower values are implied. |
| .BR |
| 8 \- DBG_DS_ON |
| .BR |
| 7 \- DBG_RX_ON | DBG_TX_ON |
| .BR |
| 6 \- DBG_PARAM_ON |
| .BR |
| 5 \- DBG_TRACE_ON |
| .BR |
| 4 \- DBG_VERBOSE_ON |
| .BR |
| If the module is compiled with debugging enabled, pc_debug defaults to 5. |
| DebugFlag overrules pc_debug. |
| .BR |
| The name pc_debug rather than PcDebug, since pc_debug is used by many PCMCIA driver. |
| .TP |
| .B PMEnabled=b |
| Sets the card\'s Power Management state. |
| .BR |
| 0 \- Disable |
| .BR |
| 1 \- Enable Enhanced Mode |
| .BR |
| 2 \- Enabled Standard Mode |
| .BR |
| 0x8000 \- Enhanced?????? Mode (to be combined with 0x0001 or 0x0002) |
| |
| Default: 0 (Disabled) |
| .TP |
| .B PMHoldoverDuration=n |
| Time that the station remains in an awake state after a MAC frame transfer if |
| Enhanced Power Save is active. |
| .BR |
| Range: 1..1000 |
| .BR |
| Default: 100 |
| .TP |
| .B PowerMode |
| ??????????????? |
| .TP |
| .B PortType=n |
| Selects the type of network operation. |
| .BR |
| 1 \- Normal Operation (BSS or IBSS) |
| .BR |
| 3 \- Ad-Hoc Demo Mode |
| .BR |
| Default: 1 |
| .TP |
| .B PromiscuousMode=s |
| Switch for promiscuous mode reception. |
| .BR |
| Default: N |
| .TP |
| .B RejectANY=s |
| Controls how stations associate to the device. |
| .BR |
| Y \- Stations must provide the correct SSID to |
| associate to the AP. |
| .BR |
| N \- Stations are not required to provide the |
| correct SSID to associate to the AP. |
| Known as an \'open\' network. |
| .BR |
| Default - N |
| .TP |
| .B RTSThreshold=n |
| Controls the RTS/CTS handshake threshold for transmissions in Station mode. |
| Valid values are 0 to 2347. |
| .BR |
| 500 \- Hidden Stations |
| .BR |
| 2347 \- No RTS/CTS |
| .BR |
| Default: 2347 |
| .TP |
| .B RTSThreshold1=n |
| Same as RTSThreshold, only for port 1 of in AccessPoint mode. |
| .TP |
| .B RTSThreshold2=n |
| Same as RTSThreshold1, only for port 2. |
| .TP |
| .B RTSThreshold3=n |
| Same as RTSThreshold1, only for port 3. |
| .TP |
| .B RTSThreshold4=n |
| Same as RTSThreshold1, only for port 4. |
| .TP |
| .B RTSThreshold5=n |
| Same as RTSThreshold1, only for port 5. |
| .TP |
| .B RTSThreshold6=n |
| Same as RTSThreshold1, only for port 6. |
| .TP |
| .B SRSC2GHz=b |
| Sets the card\'s Supported Rate Set in the 2.4GHz band. The value |
| is an INTEGER CONVERTED bit mask representing the rates to support, |
| where the rates supported are as follows: |
| |
| Bit : 15|14|13|12|11|10|09|08|07|06|05|04|03|02|01|00 |
| .br |
| ------------------------------------------------------ |
| .br |
| Rate : XX|XX|XX|XX|54|48|36|24|18|12| 9| 6|11|5.5|2| 1 |
| .BR |
| Default: 4095 (or 0x0FFF, all 11b and 11g rates) |
| .TP |
| .B SRSC5GHz=b |
| Sets the card\'s Supported Rate Set in the 5.0GHz band. See SRSC2GHz |
| for the value\'s format. |
| .BR |
| Default: 4080 (or 0x0FF0, all 11a rates) |
| .TP |
| .B SystemScale=n |
| Sets the distance between Access Points in the network. This value |
| influences the Modem Thresholds (EnergyDetectThreshold, |
| CarrierDetectThreshold and DeferThreshold) and |
| the Roaming Thresholds (CellSearchThreshold and OutOfRangeThreshold). |
| .BR |
| 1 \- Large |
| .BR |
| 2 \- Medium |
| .BR |
| 3 \- Small |
| .BR |
| Default: 1 |
| .TP |
| .B TxRateControl=n |
| Sets the data rate to be used by the transmitter. For Hermes-II: |
| .BR |
| 1 \- Fixed Low (1 Mb/sec) |
| .BR |
| 2 \- Fixed Standard (2 Mb/sec) |
| .BR |
| 3 \- Auto Rate Select High (11, 5.5, 2, 1 Mb/sec) |
| .BR |
| 4 \- Fixed Medium (5.5 Mb/sec) |
| .BR |
| 5 \- Fixed High (11 Mb/sec) |
| .BR |
| 6 \- Auto Rate Select Standard (2, 1 Mb/sec) |
| .BR |
| 7 \- Auto Rate Select Medium (5.5, 2, 1 Mb/sec) |
| .BR |
| Default: 3 |
| |
| For Hermes-II.5, an INTEGER CONVERTED bit mask representing all of the |
| rates to support, where the rates supported are as follows: |
| |
| Bit : 15|14|13|12|11|10|09|08|07|06|05|04|03|02|01|00 |
| .br |
| ------------------------------------------------------ |
| .br |
| Rate : XX|XX|XX|XX|54|48|36|24|18|12| 9| 6|11|5.5|2| 1 |
| .BR |
| Default: 4095 (Translates to 0xFFF, which is all rates) |
| .TP |
| .B RTSThreshold=n |
| Sets the number of octets in a message or fragment above which a |
| RTS/CTS handshake is performed. |
| Valid values are 0 to 2347. |
| .BR |
| 500 \- Hidden Stations |
| .BR |
| 2347 \- No RTS/CTS |
| .BR |
| Default: 2347 |
| .TP |
| .B TxKey=n |
| Designates which of the keys is to be used for the enciphering of data that is |
| transmitted by this station. |
| .BR |
| Integer in the range 1..4. |
| .BR |
| Default: 1 |
| .TP |
| .B TxPowLevel |
| ??????????????? |
| .TP |
| .B TxRateControl=n |
| Sets the data rate to be used by the transmitter in Station mode. |
| .BR |
| 1 \- Fixed Low |
| .BR |
| 2 \- Fixed Standard |
| .BR |
| 3 \- Auto Rate Select (High) |
| .BR |
| 4 \- Fixed Medium |
| .BR |
| 5 \- Fixed High |
| .BR |
| 6 \- Auto Rate Select (Standard) |
| .BR |
| 7 \- Auto Rate Select (Medium) |
| .BR |
| Default: 3 |
| |
| For Hermes-II.5, an INTEGER CONVERTED bit mask representing all of the |
| rates to support, where the rates supported are as follows: |
| |
| Bit : 15|14|13|12|11|10|09|08|07|06|05|04|03|02|01|00 |
| .br |
| ------------------------------------------------------ |
| .br |
| Rate : XX|XX|XX|XX|54|48|36|24|18|12| 9| 6|11|5.5|2| 1 |
| .BR |
| Default: 4095 (Translates to 0xFFF, which is all rates) |
| |
| .TP |
| .B TxRateControl1=n |
| Same as TxRateControl, only for port 1 in AccessPoint mode. |
| .TP |
| .B TxRateControl2=n |
| Same as TxRateControl1, only for port 2. |
| .TP |
| .B TxRateControl3=n |
| Same as TxRateControl1, only for port 3. |
| .TP |
| .B TxRateControl4=n |
| Same as TxRateControl1, only for port 4. |
| .TP |
| .B TxRateControl5=n |
| Same as TxRateControl1, only for port 5. |
| .TP |
| .B TxRateControl6=n |
| Same as TxRateControl1, only for port 6. |
| .TP |
| .B VendorDescription |
| ??????????????? |
| .TP |
| .B WDSAddress=n,n,n,n,n,n |
| MAC address that identifies the corresponding node of the WDS port in Station mode. |
| Note that for WDS to work properly, a bridge interface must be setup between the device and |
| the wds network devices created by the driver. For more information on bridge |
| interfaces, please refer to the man page for \'brctl\'. |
| .BR |
| Default: 00:00:00:00:00:00 |
| .TP |
| .B WDSAddress1=n,n,n,n,n,n |
| Same as WDSAddress, only for port 1 in AccessPoint mode. |
| .TP |
| .B WDSAddress2=n,n,n,n,n,n |
| Same as WDSAddress1, only for port 2. |
| .TP |
| .B WDSAddress3=n,n,n,n,n,n |
| Same as WDSAddress1, only for port 3. |
| .TP |
| .B WDSAddress4=n,n,n,n,n,n |
| Same as WDSAddress1, only for port 4. |
| .TP |
| .B WDSAddress5=n,n,n,n,n,n |
| Same as WDSAddress1, only for port 5. |
| .TP |
| .B WDSAddress6=n,n,n,n,n,n |
| Same as WDSAddress1, only for port 6. |
| .SH SECURITY |
| On a multi-user system only the system administrator needs access to the WEP |
| encryption keys. In this case, consider removing the read permission for |
| normal users of the PCMCIA config.opts file, the system log file, and any |
| Agere proprietary iwconfig-eth<n> scripts. |
| .SH CONTACT |
| If you encounter problems when installing or using this product, or would like |
| information about our other "Wireless" products, please contact your local |
| Authorized "Wireless" Reseller or Agere Systems sales office. |
| |
| Addresses and telephone numbers of the Agere Systems sales offices are |
| listed on our Agere Systems web site. |
| .TP |
| .B WWW |
| http://www.agere.com |
| .SH SEE ALSO |
| .BR cardmgr (8), |
| .BR pcmcia (5), |
| .BR ifconfig (8), |
| .BR insmod (8), |
| .BR brctl (8). |