| if NLM_XLP_BOARD || NLM_XLR_BOARD |
| |
| if NLM_XLP_BOARD |
| config DT_XLP_EVP |
| bool "Built-in device tree for XLP EVP boards" |
| default y |
| select BUILTIN_DTB |
| help |
| Add an FDT blob for XLP EVP boards into the kernel. |
| This DTB will be used if the firmware does not pass in a DTB |
| pointer to the kernel. The corresponding DTS file is at |
| arch/mips/netlogic/dts/xlp_evp.dts |
| |
| config DT_XLP_SVP |
| bool "Built-in device tree for XLP SVP boards" |
| default y |
| select BUILTIN_DTB |
| help |
| Add an FDT blob for XLP VP boards into the kernel. |
| This DTB will be used if the firmware does not pass in a DTB |
| pointer to the kernel. The corresponding DTS file is at |
| arch/mips/netlogic/dts/xlp_svp.dts |
| |
| config DT_XLP_FVP |
| bool "Built-in device tree for XLP FVP boards" |
| default y |
| select BUILTIN_DTB |
| help |
| Add an FDT blob for XLP FVP board into the kernel. |
| This DTB will be used if the firmware does not pass in a DTB |
| pointer to the kernel. The corresponding DTS file is at |
| arch/mips/netlogic/dts/xlp_fvp.dts |
| |
| config DT_XLP_GVP |
| bool "Built-in device tree for XLP GVP boards" |
| default y |
| select BUILTIN_DTB |
| help |
| Add an FDT blob for XLP GVP board into the kernel. |
| This DTB will be used if the firmware does not pass in a DTB |
| pointer to the kernel. The corresponding DTS file is at |
| arch/mips/netlogic/dts/xlp_gvp.dts |
| |
| config DT_XLP_RVP |
| bool "Built-in device tree for XLP RVP boards" |
| default y |
| help |
| Add an FDT blob for XLP RVP board into the kernel. |
| This DTB will be used if the firmware does not pass in a DTB |
| pointer to the kernel. The corresponding DTS file is at |
| arch/mips/netlogic/dts/xlp_rvp.dts |
| |
| config NLM_MULTINODE |
| bool "Support for multi-chip boards" |
| depends on NLM_XLP_BOARD |
| default n |
| help |
| Add support for boards with 2 or 4 XLPs connected over ICI. |
| |
| if NLM_MULTINODE |
| choice |
| prompt "Number of XLPs on the board" |
| default NLM_MULTINODE_2 |
| help |
| In the multi-node case, specify the number of SoCs on the board. |
| |
| config NLM_MULTINODE_2 |
| bool "Dual-XLP board" |
| help |
| Support boards with upto two XLPs connected over ICI. |
| |
| config NLM_MULTINODE_4 |
| bool "Quad-XLP board" |
| help |
| Support boards with upto four XLPs connected over ICI. |
| |
| endchoice |
| |
| endif |
| endif |
| |
| config NLM_COMMON |
| bool |
| |
| config IOMMU_HELPER |
| bool |
| |
| config NEED_SG_DMA_LENGTH |
| bool |
| |
| config SWIOTLB |
| def_bool y |
| select NEED_SG_DMA_LENGTH |
| select IOMMU_HELPER |
| |
| endif |
