drivers/net/wireless/ti/wl18xx/reg.h - kernel/lockdown - Git at Google

 /*
  * This file is part of wlcore
  *
  * Copyright (C) 2011 Texas Instruments Inc.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License
  * version 2 as published by the Free Software Foundation.
  *
  * This program is distributed in the hope that it will be useful, but
  * WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
  * General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
  * 02110-1301 USA
  *
  */

 #ifndef __REG_H__
 #define __REG_H__

 #define WL18XX_REGISTERS_BASE      0x00800000
 #define WL18XX_CODE_BASE           0x00000000
 #define WL18XX_DATA_BASE           0x00400000
 #define WL18XX_DOUBLE_BUFFER_BASE  0x00600000
 #define WL18XX_MCU_KEY_SEARCH_BASE 0x00700000
 #define WL18XX_PHY_BASE            0x00900000
 #define WL18XX_TOP_OCP_BASE        0x00A00000
 #define WL18XX_PACKET_RAM_BASE     0x00B00000
 #define WL18XX_HOST_BASE           0x00C00000

 #define WL18XX_REGISTERS_DOWN_SIZE 0x0000B000

 #define WL18XX_REG_BOOT_PART_START 0x00802000
 #define WL18XX_REG_BOOT_PART_SIZE  0x00014578

 #define WL18XX_PHY_INIT_MEM_ADDR   0x80926000
 #define WL18XX_PHY_END_MEM_ADDR	   0x8093CA44
 #define WL18XX_PHY_INIT_MEM_SIZE \
 	(WL18XX_PHY_END_MEM_ADDR - WL18XX_PHY_INIT_MEM_ADDR)

 #define WL18XX_SDIO_WSPI_BASE		(WL18XX_REGISTERS_BASE)
 #define WL18XX_REG_CONFIG_BASE		(WL18XX_REGISTERS_BASE + 0x02000)
 #define WL18XX_WGCM_REGS_BASE		(WL18XX_REGISTERS_BASE + 0x03000)
 #define WL18XX_ENC_BASE			(WL18XX_REGISTERS_BASE + 0x04000)
 #define WL18XX_INTERRUPT_BASE		(WL18XX_REGISTERS_BASE + 0x05000)
 #define WL18XX_UART_BASE		(WL18XX_REGISTERS_BASE + 0x06000)
 #define WL18XX_WELP_BASE		(WL18XX_REGISTERS_BASE + 0x07000)
 #define WL18XX_TCP_CKSM_BASE		(WL18XX_REGISTERS_BASE + 0x08000)
 #define WL18XX_FIFO_BASE		(WL18XX_REGISTERS_BASE + 0x09000)
 #define WL18XX_OCP_BRIDGE_BASE		(WL18XX_REGISTERS_BASE + 0x0A000)
 #define WL18XX_PMAC_RX_BASE		(WL18XX_REGISTERS_BASE + 0x14800)
 #define WL18XX_PMAC_ACM_BASE		(WL18XX_REGISTERS_BASE + 0x14C00)
 #define WL18XX_PMAC_TX_BASE		(WL18XX_REGISTERS_BASE + 0x15000)
 #define WL18XX_PMAC_CSR_BASE		(WL18XX_REGISTERS_BASE + 0x15400)

 #define WL18XX_REG_ECPU_CONTROL		(WL18XX_REGISTERS_BASE + 0x02004)
 #define WL18XX_REG_INTERRUPT_NO_CLEAR	(WL18XX_REGISTERS_BASE + 0x050E8)
 #define WL18XX_REG_INTERRUPT_ACK	(WL18XX_REGISTERS_BASE + 0x050F0)
 #define WL18XX_REG_INTERRUPT_TRIG	(WL18XX_REGISTERS_BASE + 0x5074)
 #define WL18XX_REG_INTERRUPT_TRIG_H	(WL18XX_REGISTERS_BASE + 0x5078)
 #define WL18XX_REG_INTERRUPT_MASK	(WL18XX_REGISTERS_BASE + 0x0050DC)

 #define WL18XX_REG_CHIP_ID_B		(WL18XX_REGISTERS_BASE + 0x01542C)

 #define WL18XX_SLV_MEM_DATA		(WL18XX_HOST_BASE + 0x0018)
 #define WL18XX_SLV_REG_DATA		(WL18XX_HOST_BASE + 0x0008)

 /* Scratch Pad registers*/
 #define WL18XX_SCR_PAD0			(WL18XX_REGISTERS_BASE + 0x0154EC)
 #define WL18XX_SCR_PAD1			(WL18XX_REGISTERS_BASE + 0x0154F0)
 #define WL18XX_SCR_PAD2			(WL18XX_REGISTERS_BASE + 0x0154F4)
 #define WL18XX_SCR_PAD3			(WL18XX_REGISTERS_BASE + 0x0154F8)
 #define WL18XX_SCR_PAD4			(WL18XX_REGISTERS_BASE + 0x0154FC)
 #define WL18XX_SCR_PAD4_SET		(WL18XX_REGISTERS_BASE + 0x015504)
 #define WL18XX_SCR_PAD4_CLR		(WL18XX_REGISTERS_BASE + 0x015500)
 #define WL18XX_SCR_PAD5			(WL18XX_REGISTERS_BASE + 0x015508)
 #define WL18XX_SCR_PAD5_SET		(WL18XX_REGISTERS_BASE + 0x015510)
 #define WL18XX_SCR_PAD5_CLR		(WL18XX_REGISTERS_BASE + 0x01550C)
 #define WL18XX_SCR_PAD6			(WL18XX_REGISTERS_BASE + 0x015514)
 #define WL18XX_SCR_PAD7			(WL18XX_REGISTERS_BASE + 0x015518)
 #define WL18XX_SCR_PAD8			(WL18XX_REGISTERS_BASE + 0x01551C)
 #define WL18XX_SCR_PAD9			(WL18XX_REGISTERS_BASE + 0x015520)

 /* Spare registers*/
 #define WL18XX_SPARE_A1			(WL18XX_REGISTERS_BASE + 0x002194)
 #define WL18XX_SPARE_A2			(WL18XX_REGISTERS_BASE + 0x002198)
 #define WL18XX_SPARE_A3			(WL18XX_REGISTERS_BASE + 0x00219C)
 #define WL18XX_SPARE_A4			(WL18XX_REGISTERS_BASE + 0x0021A0)
 #define WL18XX_SPARE_A5			(WL18XX_REGISTERS_BASE + 0x0021A4)
 #define WL18XX_SPARE_A6			(WL18XX_REGISTERS_BASE + 0x0021A8)
 #define WL18XX_SPARE_A7			(WL18XX_REGISTERS_BASE + 0x0021AC)
 #define WL18XX_SPARE_A8			(WL18XX_REGISTERS_BASE + 0x0021B0)
 #define WL18XX_SPARE_B1			(WL18XX_REGISTERS_BASE + 0x015524)
 #define WL18XX_SPARE_B2			(WL18XX_REGISTERS_BASE + 0x015528)
 #define WL18XX_SPARE_B3			(WL18XX_REGISTERS_BASE + 0x01552C)
 #define WL18XX_SPARE_B4			(WL18XX_REGISTERS_BASE + 0x015530)
 #define WL18XX_SPARE_B5			(WL18XX_REGISTERS_BASE + 0x015534)
 #define WL18XX_SPARE_B6			(WL18XX_REGISTERS_BASE + 0x015538)
 #define WL18XX_SPARE_B7			(WL18XX_REGISTERS_BASE + 0x01553C)
 #define WL18XX_SPARE_B8			(WL18XX_REGISTERS_BASE + 0x015540)

 #define WL18XX_REG_COMMAND_MAILBOX_PTR	(WL18XX_SCR_PAD0)
 #define WL18XX_REG_EVENT_MAILBOX_PTR	(WL18XX_SCR_PAD1)
 #define WL18XX_EEPROMLESS_IND		(WL18XX_SCR_PAD4)

 #define WL18XX_WELP_ARM_COMMAND		(WL18XX_REGISTERS_BASE + 0x7100)
 #define WL18XX_ENABLE			(WL18XX_REGISTERS_BASE + 0x01543C)

 /* PRCM registers */
 #define PLATFORM_DETECTION		0xA0E3E0
 #define OCS_EN				0xA02080
 #define PRIMARY_CLK_DETECT		0xA020A6
 #define PLLSH_COEX_PLL_N		0xA02384
 #define PLLSH_COEX_PLL_M		0xA02382
 #define PLLSH_COEX_PLL_SWALLOW_EN	0xA0238E
 #define PLLSH_WL_PLL_SEL		0xA02398

 #define PLLSH_WCS_PLL_N			0xA02362
 #define PLLSH_WCS_PLL_M			0xA02360
 #define PLLSH_WCS_PLL_Q_FACTOR_CFG_1	0xA02364
 #define PLLSH_WCS_PLL_Q_FACTOR_CFG_2	0xA02366
 #define PLLSH_WCS_PLL_P_FACTOR_CFG_1	0xA02368
 #define PLLSH_WCS_PLL_P_FACTOR_CFG_2	0xA0236A
 #define PLLSH_WCS_PLL_SWALLOW_EN	0xA0236C
 #define PLLSH_WL_PLL_EN			0xA02392

 #define PLLSH_WCS_PLL_Q_FACTOR_CFG_1_MASK	0xFFFF
 #define PLLSH_WCS_PLL_Q_FACTOR_CFG_2_MASK	0x007F
 #define PLLSH_WCS_PLL_P_FACTOR_CFG_1_MASK	0xFFFF
 #define PLLSH_WCS_PLL_P_FACTOR_CFG_2_MASK	0x000F

 #define PLLSH_WL_PLL_EN_VAL1		0x7
 #define PLLSH_WL_PLL_EN_VAL2		0x2
 #define PLLSH_COEX_PLL_SWALLOW_EN_VAL1	0x2
 #define PLLSH_COEX_PLL_SWALLOW_EN_VAL2	0x11

 #define PLLSH_WCS_PLL_SWALLOW_EN_VAL1	0x1
 #define PLLSH_WCS_PLL_SWALLOW_EN_VAL2	0x12

 #define PLLSH_WL_PLL_SEL_WCS_PLL	0x0
 #define PLLSH_WL_PLL_SEL_COEX_PLL	0x1

 #define WL18XX_REG_FUSE_DATA_1_3	0xA0260C
 #define WL18XX_PG_VER_MASK		0x70
 #define WL18XX_PG_VER_OFFSET		4
 #define WL18XX_ROM_VER_MASK		0x3e00
 #define WL18XX_ROM_VER_OFFSET		9
 #define WL18XX_METAL_VER_MASK		0xC
 #define WL18XX_METAL_VER_OFFSET		2
 #define WL18XX_NEW_METAL_VER_MASK	0x180
 #define WL18XX_NEW_METAL_VER_OFFSET	7

 #define WL18XX_PACKAGE_TYPE_OFFSET	13
 #define WL18XX_PACKAGE_TYPE_WSP		0

 #define WL18XX_REG_FUSE_DATA_2_3	0xA02614
 #define WL18XX_RDL_VER_MASK		0x1f00
 #define WL18XX_RDL_VER_OFFSET		8

 #define WL18XX_REG_FUSE_BD_ADDR_1	0xA02602
 #define WL18XX_REG_FUSE_BD_ADDR_2	0xA02606

 #define WL18XX_CMD_MBOX_ADDRESS		0xB007B4

 #define WL18XX_FW_STATUS_ADDR		0x50F8

 #define CHIP_ID_185x_PG10              (0x06030101)
 #define CHIP_ID_185x_PG20              (0x06030111)

 /*
  * Host Command Interrupt. Setting this bit masks
  * the interrupt that the host issues to inform
  * the FW that it has sent a command
  * to the Wlan hardware Command Mailbox.
  */
 #define WL18XX_INTR_TRIG_CMD       BIT(28)

 /*
  * Host Event Acknowlegde Interrupt. The host
  * sets this bit to acknowledge that it received
  * the unsolicited information from the event
  * mailbox.
  */
 #define WL18XX_INTR_TRIG_EVENT_ACK BIT(29)

 /*
  * To boot the firmware in PLT mode we need to write this value in
  * SCR_PAD8 before starting.
  */
 #define WL18XX_SCR_PAD8_PLT	0xBABABEBE

 enum {
 	COMPONENT_NO_SWITCH	= 0x0,
 	COMPONENT_2_WAY_SWITCH	= 0x1,
 	COMPONENT_3_WAY_SWITCH	= 0x2,
 	COMPONENT_MATCHING	= 0x3,
 };

 enum {
 	FEM_NONE	= 0x0,
 	FEM_VENDOR_1	= 0x1,
 	FEM_VENDOR_2	= 0x2,
 	FEM_VENDOR_3	= 0x3,
 };

 enum {
 	BOARD_TYPE_EVB_18XX     = 0,
 	BOARD_TYPE_DVP_18XX     = 1,
 	BOARD_TYPE_HDK_18XX     = 2,
 	BOARD_TYPE_FPGA_18XX    = 3,
 	BOARD_TYPE_COM8_18XX    = 4,

 	NUM_BOARD_TYPES,
 };

 enum wl18xx_rdl_num {
 	RDL_NONE	= 0,
 	RDL_1_HP	= 1,
 	RDL_2_SP	= 2,
 	RDL_3_HP	= 3,
 	RDL_4_SP	= 4,
 	RDL_5_SP	= 0x11,
 	RDL_6_SP	= 0x12,
 	RDL_7_SP	= 0x13,
 	RDL_8_SP	= 0x14,

 	_RDL_LAST,
 	RDL_MAX = _RDL_LAST - 1,
 };


 /* FPGA_SPARE_1 register - used to change the PHY ATPG clock at boot time */
 #define WL18XX_PHY_FPGA_SPARE_1		0x8093CA40

 /* command to disable FDSP clock */
 #define MEM_FDSP_CLK_120_DISABLE        0x80000000

 /* command to set ATPG clock toward FDSP Code RAM rather than its own clock */
 #define MEM_FDSP_CODERAM_FUNC_CLK_SEL	0xC0000000

 /* command to re-enable FDSP clock */
 #define MEM_FDSP_CLK_120_ENABLE		0x40000000

 #endif /* __REG_H__ */
	/*
	* This file is part of wlcore
	*
	* Copyright (C) 2011 Texas Instruments Inc.
	*
	* This program is free software; you can redistribute it and/or
	* modify it under the terms of the GNU General Public License
	* version 2 as published by the Free Software Foundation.
	*
	* This program is distributed in the hope that it will be useful, but
	* WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
	* General Public License for more details.
	*
	* You should have received a copy of the GNU General Public License
	* along with this program; if not, write to the Free Software
	* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
	* 02110-1301 USA
	*
	*/

	#ifndef __REG_H__
	#define __REG_H__

	#define WL18XX_REGISTERS_BASE 0x00800000
	#define WL18XX_CODE_BASE 0x00000000
	#define WL18XX_DATA_BASE 0x00400000
	#define WL18XX_DOUBLE_BUFFER_BASE 0x00600000
	#define WL18XX_MCU_KEY_SEARCH_BASE 0x00700000
	#define WL18XX_PHY_BASE 0x00900000
	#define WL18XX_TOP_OCP_BASE 0x00A00000
	#define WL18XX_PACKET_RAM_BASE 0x00B00000
	#define WL18XX_HOST_BASE 0x00C00000

	#define WL18XX_REGISTERS_DOWN_SIZE 0x0000B000

	#define WL18XX_REG_BOOT_PART_START 0x00802000
	#define WL18XX_REG_BOOT_PART_SIZE 0x00014578

	#define WL18XX_PHY_INIT_MEM_ADDR 0x80926000
	#define WL18XX_PHY_END_MEM_ADDR 0x8093CA44
	#define WL18XX_PHY_INIT_MEM_SIZE \
	(WL18XX_PHY_END_MEM_ADDR - WL18XX_PHY_INIT_MEM_ADDR)

	#define WL18XX_SDIO_WSPI_BASE (WL18XX_REGISTERS_BASE)
	#define WL18XX_REG_CONFIG_BASE (WL18XX_REGISTERS_BASE + 0x02000)
	#define WL18XX_WGCM_REGS_BASE (WL18XX_REGISTERS_BASE + 0x03000)
	#define WL18XX_ENC_BASE (WL18XX_REGISTERS_BASE + 0x04000)
	#define WL18XX_INTERRUPT_BASE (WL18XX_REGISTERS_BASE + 0x05000)
	#define WL18XX_UART_BASE (WL18XX_REGISTERS_BASE + 0x06000)
	#define WL18XX_WELP_BASE (WL18XX_REGISTERS_BASE + 0x07000)
	#define WL18XX_TCP_CKSM_BASE (WL18XX_REGISTERS_BASE + 0x08000)
	#define WL18XX_FIFO_BASE (WL18XX_REGISTERS_BASE + 0x09000)
	#define WL18XX_OCP_BRIDGE_BASE (WL18XX_REGISTERS_BASE + 0x0A000)
	#define WL18XX_PMAC_RX_BASE (WL18XX_REGISTERS_BASE + 0x14800)
	#define WL18XX_PMAC_ACM_BASE (WL18XX_REGISTERS_BASE + 0x14C00)
	#define WL18XX_PMAC_TX_BASE (WL18XX_REGISTERS_BASE + 0x15000)
	#define WL18XX_PMAC_CSR_BASE (WL18XX_REGISTERS_BASE + 0x15400)

	#define WL18XX_REG_ECPU_CONTROL (WL18XX_REGISTERS_BASE + 0x02004)
	#define WL18XX_REG_INTERRUPT_NO_CLEAR (WL18XX_REGISTERS_BASE + 0x050E8)
	#define WL18XX_REG_INTERRUPT_ACK (WL18XX_REGISTERS_BASE + 0x050F0)
	#define WL18XX_REG_INTERRUPT_TRIG (WL18XX_REGISTERS_BASE + 0x5074)
	#define WL18XX_REG_INTERRUPT_TRIG_H (WL18XX_REGISTERS_BASE + 0x5078)
	#define WL18XX_REG_INTERRUPT_MASK (WL18XX_REGISTERS_BASE + 0x0050DC)

	#define WL18XX_REG_CHIP_ID_B (WL18XX_REGISTERS_BASE + 0x01542C)

	#define WL18XX_SLV_MEM_DATA (WL18XX_HOST_BASE + 0x0018)
	#define WL18XX_SLV_REG_DATA (WL18XX_HOST_BASE + 0x0008)

	/* Scratch Pad registers*/
	#define WL18XX_SCR_PAD0 (WL18XX_REGISTERS_BASE + 0x0154EC)
	#define WL18XX_SCR_PAD1 (WL18XX_REGISTERS_BASE + 0x0154F0)
	#define WL18XX_SCR_PAD2 (WL18XX_REGISTERS_BASE + 0x0154F4)
	#define WL18XX_SCR_PAD3 (WL18XX_REGISTERS_BASE + 0x0154F8)
	#define WL18XX_SCR_PAD4 (WL18XX_REGISTERS_BASE + 0x0154FC)
	#define WL18XX_SCR_PAD4_SET (WL18XX_REGISTERS_BASE + 0x015504)
	#define WL18XX_SCR_PAD4_CLR (WL18XX_REGISTERS_BASE + 0x015500)
	#define WL18XX_SCR_PAD5 (WL18XX_REGISTERS_BASE + 0x015508)
	#define WL18XX_SCR_PAD5_SET (WL18XX_REGISTERS_BASE + 0x015510)
	#define WL18XX_SCR_PAD5_CLR (WL18XX_REGISTERS_BASE + 0x01550C)
	#define WL18XX_SCR_PAD6 (WL18XX_REGISTERS_BASE + 0x015514)
	#define WL18XX_SCR_PAD7 (WL18XX_REGISTERS_BASE + 0x015518)
	#define WL18XX_SCR_PAD8 (WL18XX_REGISTERS_BASE + 0x01551C)
	#define WL18XX_SCR_PAD9 (WL18XX_REGISTERS_BASE + 0x015520)

	/* Spare registers*/
	#define WL18XX_SPARE_A1 (WL18XX_REGISTERS_BASE + 0x002194)
	#define WL18XX_SPARE_A2 (WL18XX_REGISTERS_BASE + 0x002198)
	#define WL18XX_SPARE_A3 (WL18XX_REGISTERS_BASE + 0x00219C)
	#define WL18XX_SPARE_A4 (WL18XX_REGISTERS_BASE + 0x0021A0)
	#define WL18XX_SPARE_A5 (WL18XX_REGISTERS_BASE + 0x0021A4)
	#define WL18XX_SPARE_A6 (WL18XX_REGISTERS_BASE + 0x0021A8)
	#define WL18XX_SPARE_A7 (WL18XX_REGISTERS_BASE + 0x0021AC)
	#define WL18XX_SPARE_A8 (WL18XX_REGISTERS_BASE + 0x0021B0)
	#define WL18XX_SPARE_B1 (WL18XX_REGISTERS_BASE + 0x015524)
	#define WL18XX_SPARE_B2 (WL18XX_REGISTERS_BASE + 0x015528)
	#define WL18XX_SPARE_B3 (WL18XX_REGISTERS_BASE + 0x01552C)
	#define WL18XX_SPARE_B4 (WL18XX_REGISTERS_BASE + 0x015530)
	#define WL18XX_SPARE_B5 (WL18XX_REGISTERS_BASE + 0x015534)
	#define WL18XX_SPARE_B6 (WL18XX_REGISTERS_BASE + 0x015538)
	#define WL18XX_SPARE_B7 (WL18XX_REGISTERS_BASE + 0x01553C)
	#define WL18XX_SPARE_B8 (WL18XX_REGISTERS_BASE + 0x015540)

	#define WL18XX_REG_COMMAND_MAILBOX_PTR (WL18XX_SCR_PAD0)
	#define WL18XX_REG_EVENT_MAILBOX_PTR (WL18XX_SCR_PAD1)
	#define WL18XX_EEPROMLESS_IND (WL18XX_SCR_PAD4)

	#define WL18XX_WELP_ARM_COMMAND (WL18XX_REGISTERS_BASE + 0x7100)
	#define WL18XX_ENABLE (WL18XX_REGISTERS_BASE + 0x01543C)

	/* PRCM registers */
	#define PLATFORM_DETECTION 0xA0E3E0
	#define OCS_EN 0xA02080
	#define PRIMARY_CLK_DETECT 0xA020A6
	#define PLLSH_COEX_PLL_N 0xA02384
	#define PLLSH_COEX_PLL_M 0xA02382
	#define PLLSH_COEX_PLL_SWALLOW_EN 0xA0238E
	#define PLLSH_WL_PLL_SEL 0xA02398

	#define PLLSH_WCS_PLL_N 0xA02362
	#define PLLSH_WCS_PLL_M 0xA02360
	#define PLLSH_WCS_PLL_Q_FACTOR_CFG_1 0xA02364
	#define PLLSH_WCS_PLL_Q_FACTOR_CFG_2 0xA02366
	#define PLLSH_WCS_PLL_P_FACTOR_CFG_1 0xA02368
	#define PLLSH_WCS_PLL_P_FACTOR_CFG_2 0xA0236A
	#define PLLSH_WCS_PLL_SWALLOW_EN 0xA0236C
	#define PLLSH_WL_PLL_EN 0xA02392

	#define PLLSH_WCS_PLL_Q_FACTOR_CFG_1_MASK 0xFFFF
	#define PLLSH_WCS_PLL_Q_FACTOR_CFG_2_MASK 0x007F
	#define PLLSH_WCS_PLL_P_FACTOR_CFG_1_MASK 0xFFFF
	#define PLLSH_WCS_PLL_P_FACTOR_CFG_2_MASK 0x000F

	#define PLLSH_WL_PLL_EN_VAL1 0x7
	#define PLLSH_WL_PLL_EN_VAL2 0x2
	#define PLLSH_COEX_PLL_SWALLOW_EN_VAL1 0x2
	#define PLLSH_COEX_PLL_SWALLOW_EN_VAL2 0x11

	#define PLLSH_WCS_PLL_SWALLOW_EN_VAL1 0x1
	#define PLLSH_WCS_PLL_SWALLOW_EN_VAL2 0x12

	#define PLLSH_WL_PLL_SEL_WCS_PLL 0x0
	#define PLLSH_WL_PLL_SEL_COEX_PLL 0x1

	#define WL18XX_REG_FUSE_DATA_1_3 0xA0260C
	#define WL18XX_PG_VER_MASK 0x70
	#define WL18XX_PG_VER_OFFSET 4
	#define WL18XX_ROM_VER_MASK 0x3e00
	#define WL18XX_ROM_VER_OFFSET 9
	#define WL18XX_METAL_VER_MASK 0xC
	#define WL18XX_METAL_VER_OFFSET 2
	#define WL18XX_NEW_METAL_VER_MASK 0x180
	#define WL18XX_NEW_METAL_VER_OFFSET 7

	#define WL18XX_PACKAGE_TYPE_OFFSET 13
	#define WL18XX_PACKAGE_TYPE_WSP 0

	#define WL18XX_REG_FUSE_DATA_2_3 0xA02614
	#define WL18XX_RDL_VER_MASK 0x1f00
	#define WL18XX_RDL_VER_OFFSET 8

	#define WL18XX_REG_FUSE_BD_ADDR_1 0xA02602
	#define WL18XX_REG_FUSE_BD_ADDR_2 0xA02606

	#define WL18XX_CMD_MBOX_ADDRESS 0xB007B4

	#define WL18XX_FW_STATUS_ADDR 0x50F8

	#define CHIP_ID_185x_PG10 (0x06030101)
	#define CHIP_ID_185x_PG20 (0x06030111)

	/*
	* Host Command Interrupt. Setting this bit masks
	* the interrupt that the host issues to inform
	* the FW that it has sent a command
	* to the Wlan hardware Command Mailbox.
	*/
	#define WL18XX_INTR_TRIG_CMD BIT(28)

	/*
	* Host Event Acknowlegde Interrupt. The host
	* sets this bit to acknowledge that it received
	* the unsolicited information from the event
	* mailbox.
	*/
	#define WL18XX_INTR_TRIG_EVENT_ACK BIT(29)

	/*
	* To boot the firmware in PLT mode we need to write this value in
	* SCR_PAD8 before starting.
	*/
	#define WL18XX_SCR_PAD8_PLT 0xBABABEBE

	enum {
	COMPONENT_NO_SWITCH = 0x0,
	COMPONENT_2_WAY_SWITCH = 0x1,
	COMPONENT_3_WAY_SWITCH = 0x2,
	COMPONENT_MATCHING = 0x3,
	};

	enum {
	FEM_NONE = 0x0,
	FEM_VENDOR_1 = 0x1,
	FEM_VENDOR_2 = 0x2,
	FEM_VENDOR_3 = 0x3,
	};

	enum {
	BOARD_TYPE_EVB_18XX = 0,
	BOARD_TYPE_DVP_18XX = 1,
	BOARD_TYPE_HDK_18XX = 2,
	BOARD_TYPE_FPGA_18XX = 3,
	BOARD_TYPE_COM8_18XX = 4,

	NUM_BOARD_TYPES,
	};

	enum wl18xx_rdl_num {
	RDL_NONE = 0,
	RDL_1_HP = 1,
	RDL_2_SP = 2,
	RDL_3_HP = 3,
	RDL_4_SP = 4,
	RDL_5_SP = 0x11,
	RDL_6_SP = 0x12,
	RDL_7_SP = 0x13,
	RDL_8_SP = 0x14,

	_RDL_LAST,
	RDL_MAX = _RDL_LAST - 1,
	};


	/* FPGA_SPARE_1 register - used to change the PHY ATPG clock at boot time */
	#define WL18XX_PHY_FPGA_SPARE_1 0x8093CA40

	/* command to disable FDSP clock */
	#define MEM_FDSP_CLK_120_DISABLE 0x80000000

	/* command to set ATPG clock toward FDSP Code RAM rather than its own clock */
	#define MEM_FDSP_CODERAM_FUNC_CLK_SEL 0xC0000000

	/* command to re-enable FDSP clock */
	#define MEM_FDSP_CLK_120_ENABLE 0x40000000

	#endif /* __REG_H__ */