blob: 6d915b063d93449f7dee9d762b7002492940040e [file] [log] [blame] [edit]
/*
* pata_cypress.c - Cypress PATA for new ATA layer
* (C) 2006 Red Hat Inc
* Alan Cox
*
* Based heavily on
* linux/drivers/ide/pci/cy82c693.c Version 0.40 Sep. 10, 2002
*
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_cypress"
#define DRV_VERSION "0.1.5"
/* here are the offset definitions for the registers */
enum {
CY82_IDE_CMDREG = 0x04,
CY82_IDE_ADDRSETUP = 0x48,
CY82_IDE_MASTER_IOR = 0x4C,
CY82_IDE_MASTER_IOW = 0x4D,
CY82_IDE_SLAVE_IOR = 0x4E,
CY82_IDE_SLAVE_IOW = 0x4F,
CY82_IDE_MASTER_8BIT = 0x50,
CY82_IDE_SLAVE_8BIT = 0x51,
CY82_INDEX_PORT = 0x22,
CY82_DATA_PORT = 0x23,
CY82_INDEX_CTRLREG1 = 0x01,
CY82_INDEX_CHANNEL0 = 0x30,
CY82_INDEX_CHANNEL1 = 0x31,
CY82_INDEX_TIMEOUT = 0x32
};
/**
* cy82c693_set_piomode - set initial PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
* Called to do the PIO mode setup.
*/
static void cy82c693_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
struct ata_timing t;
const unsigned long T = 1000000 / 33;
short time_16, time_8;
u32 addr;
if (ata_timing_compute(adev, adev->pio_mode, &t, T, 1) < 0) {
printk(KERN_ERR DRV_NAME ": mome computation failed.\n");
return;
}
time_16 = clamp_val(t.recover - 1, 0, 15) |
(clamp_val(t.active - 1, 0, 15) << 4);
time_8 = clamp_val(t.act8b - 1, 0, 15) |
(clamp_val(t.rec8b - 1, 0, 15) << 4);
if (adev->devno == 0) {
pci_read_config_dword(pdev, CY82_IDE_ADDRSETUP, &addr);
addr &= ~0x0F; /* Mask bits */
addr |= clamp_val(t.setup - 1, 0, 15);
pci_write_config_dword(pdev, CY82_IDE_ADDRSETUP, addr);
pci_write_config_byte(pdev, CY82_IDE_MASTER_IOR, time_16);
pci_write_config_byte(pdev, CY82_IDE_MASTER_IOW, time_16);
pci_write_config_byte(pdev, CY82_IDE_MASTER_8BIT, time_8);
} else {
pci_read_config_dword(pdev, CY82_IDE_ADDRSETUP, &addr);
addr &= ~0xF0; /* Mask bits */
addr |= (clamp_val(t.setup - 1, 0, 15) << 4);
pci_write_config_dword(pdev, CY82_IDE_ADDRSETUP, addr);
pci_write_config_byte(pdev, CY82_IDE_SLAVE_IOR, time_16);
pci_write_config_byte(pdev, CY82_IDE_SLAVE_IOW, time_16);
pci_write_config_byte(pdev, CY82_IDE_SLAVE_8BIT, time_8);
}
}
/**
* cy82c693_set_dmamode - set initial DMA mode data
* @ap: ATA interface
* @adev: ATA device
*
* Called to do the DMA mode setup.
*/
static void cy82c693_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
int reg = CY82_INDEX_CHANNEL0 + ap->port_no;
/* Be afraid, be very afraid. Magic registers in low I/O space */
outb(reg, 0x22);
outb(adev->dma_mode - XFER_MW_DMA_0, 0x23);
/* 0x50 gives the best behaviour on the Alpha's using this chip */
outb(CY82_INDEX_TIMEOUT, 0x22);
outb(0x50, 0x23);
}
static struct scsi_host_template cy82c693_sht = {
ATA_BMDMA_SHT(DRV_NAME),
};
static struct ata_port_operations cy82c693_port_ops = {
.inherits = &ata_bmdma_port_ops,
.cable_detect = ata_cable_40wire,
.set_piomode = cy82c693_set_piomode,
.set_dmamode = cy82c693_set_dmamode,
};
static int cy82c693_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.port_ops = &cy82c693_port_ops
};
const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info };
/* Devfn 1 is the ATA primary. The secondary is magic and on devfn2.
For the moment we don't handle the secondary. FIXME */
if (PCI_FUNC(pdev->devfn) != 1)
return -ENODEV;
return ata_pci_bmdma_init_one(pdev, ppi, &cy82c693_sht, NULL, 0);
}
static const struct pci_device_id cy82c693[] = {
{ PCI_VDEVICE(CONTAQ, PCI_DEVICE_ID_CONTAQ_82C693), },
{ },
};
static struct pci_driver cy82c693_pci_driver = {
.name = DRV_NAME,
.id_table = cy82c693,
.probe = cy82c693_init_one,
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM
.suspend = ata_pci_device_suspend,
.resume = ata_pci_device_resume,
#endif
};
static int __init cy82c693_init(void)
{
return pci_register_driver(&cy82c693_pci_driver);
}
static void __exit cy82c693_exit(void)
{
pci_unregister_driver(&cy82c693_pci_driver);
}
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the CY82C693 PATA controller");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, cy82c693);
MODULE_VERSION(DRV_VERSION);
module_init(cy82c693_init);
module_exit(cy82c693_exit);