blob: 33927d283c921b888b2d092011a0e61476ee9dc4 [file] [log] [blame]
#ifndef _ASM_X86_PGTABLE_3LEVEL_H
#define _ASM_X86_PGTABLE_3LEVEL_H
/*
* Intel Physical Address Extension (PAE) Mode - three-level page
* tables on PPro+ CPUs.
*
* Copyright (C) 1999 Ingo Molnar <mingo@redhat.com>
*/
#define pte_ERROR(e) \
printk("%s:%d: bad pte %p(%08lx%08lx).\n", \
__FILE__, __LINE__, &(e), (e).pte_high, (e).pte_low)
#define pmd_ERROR(e) \
printk("%s:%d: bad pmd %p(%016Lx).\n", \
__FILE__, __LINE__, &(e), pmd_val(e))
#define pgd_ERROR(e) \
printk("%s:%d: bad pgd %p(%016Lx).\n", \
__FILE__, __LINE__, &(e), pgd_val(e))
/* Rules for using set_pte: the pte being assigned *must* be
* either not present or in a state where the hardware will
* not attempt to update the pte. In places where this is
* not possible, use pte_get_and_clear to obtain the old pte
* value and then use set_pte to update it. -ben
*/
static inline void native_set_pte(pte_t *ptep, pte_t pte)
{
ptep->pte_high = pte.pte_high;
smp_wmb();
ptep->pte_low = pte.pte_low;
}
static inline void native_set_pte_atomic(pte_t *ptep, pte_t pte)
{
set_64bit((unsigned long long *)(ptep), native_pte_val(pte));
}
static inline void native_set_pmd(pmd_t *pmdp, pmd_t pmd)
{
set_64bit((unsigned long long *)(pmdp), native_pmd_val(pmd));
}
static inline void native_set_pud(pud_t *pudp, pud_t pud)
{
set_64bit((unsigned long long *)(pudp), native_pud_val(pud));
}
/*
* For PTEs and PDEs, we must clear the P-bit first when clearing a page table
* entry, so clear the bottom half first and enforce ordering with a compiler
* barrier.
*/
static inline void native_pte_clear(struct mm_struct *mm, unsigned long addr,
pte_t *ptep)
{
ptep->pte_low = 0;
smp_wmb();
ptep->pte_high = 0;
}
static inline void native_pmd_clear(pmd_t *pmd)
{
u32 *tmp = (u32 *)pmd;
*tmp = 0;
smp_wmb();
*(tmp + 1) = 0;
}
static inline void pud_clear(pud_t *pudp)
{
set_pud(pudp, __pud(0));
/*
* According to Intel App note "TLBs, Paging-Structure Caches,
* and Their Invalidation", April 2007, document 317080-001,
* section 8.1: in PAE mode we explicitly have to flush the
* TLB via cr3 if the top-level pgd is changed...
*
* Currently all places where pud_clear() is called either have
* flush_tlb_mm() followed or don't need TLB flush (x86_64 code or
* pud_clear_bad()), so we don't need TLB flush here.
*/
}
#ifdef CONFIG_SMP
static inline pte_t native_ptep_get_and_clear(pte_t *ptep)
{
pte_t res;
/* xchg acts as a barrier before the setting of the high bits */
res.pte_low = xchg(&ptep->pte_low, 0);
res.pte_high = ptep->pte_high;
ptep->pte_high = 0;
return res;
}
#else
#define native_ptep_get_and_clear(xp) native_local_ptep_get_and_clear(xp)
#endif
/*
* Bits 0, 6 and 7 are taken in the low part of the pte,
* put the 32 bits of offset into the high part.
*/
#define pte_to_pgoff(pte) ((pte).pte_high)
#define pgoff_to_pte(off) \
((pte_t) { { .pte_low = _PAGE_FILE, .pte_high = (off) } })
#define PTE_FILE_MAX_BITS 32
/* Encode and de-code a swap entry */
#define MAX_SWAPFILES_CHECK() BUILD_BUG_ON(MAX_SWAPFILES_SHIFT > 5)
#define __swp_type(x) (((x).val) & 0x1f)
#define __swp_offset(x) ((x).val >> 5)
#define __swp_entry(type, offset) ((swp_entry_t){(type) | (offset) << 5})
#define __pte_to_swp_entry(pte) ((swp_entry_t){ (pte).pte_high })
#define __swp_entry_to_pte(x) ((pte_t){ { .pte_high = (x).val } })
#endif /* _ASM_X86_PGTABLE_3LEVEL_H */