| /* |
| * Copyright 2011 Freescale Semiconductor, Inc. |
| * Copyright 2011 Linaro Ltd. |
| * |
| * The code contained herein is licensed under the GNU General Public |
| * License. You may obtain a copy of the GNU General Public License |
| * Version 2 or later at the following locations: |
| * |
| * http://www.opensource.org/licenses/gpl-license.html |
| * http://www.gnu.org/copyleft/gpl.html |
| */ |
| |
| #include <dt-bindings/clock/imx6qdl-clock.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| |
| #include "skeleton.dtsi" |
| |
| / { |
| aliases { |
| ethernet0 = &fec; |
| can0 = &can1; |
| can1 = &can2; |
| gpio0 = &gpio1; |
| gpio1 = &gpio2; |
| gpio2 = &gpio3; |
| gpio3 = &gpio4; |
| gpio4 = &gpio5; |
| gpio5 = &gpio6; |
| gpio6 = &gpio7; |
| i2c0 = &i2c1; |
| i2c1 = &i2c2; |
| i2c2 = &i2c3; |
| mmc0 = &usdhc1; |
| mmc1 = &usdhc2; |
| mmc2 = &usdhc3; |
| mmc3 = &usdhc4; |
| serial0 = &uart1; |
| serial1 = &uart2; |
| serial2 = &uart3; |
| serial3 = &uart4; |
| serial4 = &uart5; |
| spi0 = &ecspi1; |
| spi1 = &ecspi2; |
| spi2 = &ecspi3; |
| spi3 = &ecspi4; |
| usbphy0 = &usbphy1; |
| usbphy1 = &usbphy2; |
| }; |
| |
| intc: interrupt-controller@00a01000 { |
| compatible = "arm,cortex-a9-gic"; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| reg = <0x00a01000 0x1000>, |
| <0x00a00100 0x100>; |
| interrupt-parent = <&intc>; |
| }; |
| |
| clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ckil { |
| compatible = "fsl,imx-ckil", "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| }; |
| |
| ckih1 { |
| compatible = "fsl,imx-ckih1", "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <0>; |
| }; |
| |
| osc { |
| compatible = "fsl,imx-osc", "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <24000000>; |
| }; |
| }; |
| |
| soc { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "simple-bus"; |
| interrupt-parent = <&gpc>; |
| ranges; |
| |
| dma_apbh: dma-apbh@00110000 { |
| compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh"; |
| reg = <0x00110000 0x2000>; |
| interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>, |
| <0 13 IRQ_TYPE_LEVEL_HIGH>, |
| <0 13 IRQ_TYPE_LEVEL_HIGH>, |
| <0 13 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3"; |
| #dma-cells = <1>; |
| dma-channels = <4>; |
| clocks = <&clks IMX6QDL_CLK_APBH_DMA>; |
| }; |
| |
| gpmi: gpmi-nand@00112000 { |
| compatible = "fsl,imx6q-gpmi-nand"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x00112000 0x2000>, <0x00114000 0x2000>; |
| reg-names = "gpmi-nand", "bch"; |
| interrupts = <0 15 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "bch"; |
| clocks = <&clks IMX6QDL_CLK_GPMI_IO>, |
| <&clks IMX6QDL_CLK_GPMI_APB>, |
| <&clks IMX6QDL_CLK_GPMI_BCH>, |
| <&clks IMX6QDL_CLK_GPMI_BCH_APB>, |
| <&clks IMX6QDL_CLK_PER1_BCH>; |
| clock-names = "gpmi_io", "gpmi_apb", "gpmi_bch", |
| "gpmi_bch_apb", "per1_bch"; |
| dmas = <&dma_apbh 0>; |
| dma-names = "rx-tx"; |
| status = "disabled"; |
| }; |
| |
| hdmi: hdmi@0120000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x00120000 0x9000>; |
| interrupts = <0 115 0x04>; |
| gpr = <&gpr>; |
| clocks = <&clks IMX6QDL_CLK_HDMI_IAHB>, |
| <&clks IMX6QDL_CLK_HDMI_ISFR>; |
| clock-names = "iahb", "isfr"; |
| status = "disabled"; |
| |
| port@0 { |
| reg = <0>; |
| |
| hdmi_mux_0: endpoint { |
| remote-endpoint = <&ipu1_di0_hdmi>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| hdmi_mux_1: endpoint { |
| remote-endpoint = <&ipu1_di1_hdmi>; |
| }; |
| }; |
| }; |
| |
| timer@00a00600 { |
| compatible = "arm,cortex-a9-twd-timer"; |
| reg = <0x00a00600 0x20>; |
| interrupts = <1 13 0xf01>; |
| interrupt-parent = <&intc>; |
| clocks = <&clks IMX6QDL_CLK_TWD>; |
| }; |
| |
| L2: l2-cache@00a02000 { |
| compatible = "arm,pl310-cache"; |
| reg = <0x00a02000 0x1000>; |
| interrupts = <0 92 IRQ_TYPE_LEVEL_HIGH>; |
| cache-unified; |
| cache-level = <2>; |
| arm,tag-latency = <4 2 3>; |
| arm,data-latency = <4 2 3>; |
| }; |
| |
| pcie: pcie@0x01000000 { |
| compatible = "fsl,imx6q-pcie", "snps,dw-pcie"; |
| reg = <0x01ffc000 0x04000>, |
| <0x01f00000 0x80000>; |
| reg-names = "dbi", "config"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| device_type = "pci"; |
| ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000 /* configuration space */ |
| 0x81000000 0 0 0x01f80000 0 0x00010000 /* downstream I/O */ |
| 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */ |
| num-lanes = <1>; |
| interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "msi"; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0x7>; |
| interrupt-map = <0 0 0 1 &gpc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 2 &gpc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 3 &gpc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, |
| <0 0 0 4 &gpc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_PCIE_AXI>, |
| <&clks IMX6QDL_CLK_LVDS1_GATE>, |
| <&clks IMX6QDL_CLK_PCIE_REF_125M>; |
| clock-names = "pcie", "pcie_bus", "pcie_phy"; |
| status = "disabled"; |
| }; |
| |
| pmu { |
| compatible = "arm,cortex-a9-pmu"; |
| interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| aips-bus@02000000 { /* AIPS1 */ |
| compatible = "fsl,aips-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x02000000 0x100000>; |
| ranges; |
| |
| spba-bus@02000000 { |
| compatible = "fsl,spba-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x02000000 0x40000>; |
| ranges; |
| |
| spdif: spdif@02004000 { |
| compatible = "fsl,imx35-spdif"; |
| reg = <0x02004000 0x4000>; |
| interrupts = <0 52 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&sdma 14 18 0>, |
| <&sdma 15 18 0>; |
| dma-names = "rx", "tx"; |
| clocks = <&clks IMX6QDL_CLK_SPDIF_GCLK>, <&clks IMX6QDL_CLK_OSC>, |
| <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_ASRC>, |
| <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_ESAI_EXTAL>, |
| <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_DUMMY>, |
| <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_SPBA>; |
| clock-names = "core", "rxtx0", |
| "rxtx1", "rxtx2", |
| "rxtx3", "rxtx4", |
| "rxtx5", "rxtx6", |
| "rxtx7", "dma"; |
| status = "disabled"; |
| }; |
| |
| ecspi1: ecspi@02008000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x02008000 0x4000>; |
| interrupts = <0 31 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_ECSPI1>, |
| <&clks IMX6QDL_CLK_ECSPI1>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 3 7 1>, <&sdma 4 7 2>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| ecspi2: ecspi@0200c000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x0200c000 0x4000>; |
| interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_ECSPI2>, |
| <&clks IMX6QDL_CLK_ECSPI2>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 5 7 1>, <&sdma 6 7 2>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| ecspi3: ecspi@02010000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x02010000 0x4000>; |
| interrupts = <0 33 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_ECSPI3>, |
| <&clks IMX6QDL_CLK_ECSPI3>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 7 7 1>, <&sdma 8 7 2>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| ecspi4: ecspi@02014000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi"; |
| reg = <0x02014000 0x4000>; |
| interrupts = <0 34 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_ECSPI4>, |
| <&clks IMX6QDL_CLK_ECSPI4>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 9 7 1>, <&sdma 10 7 2>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart1: serial@02020000 { |
| compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; |
| reg = <0x02020000 0x4000>; |
| interrupts = <0 26 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_UART_IPG>, |
| <&clks IMX6QDL_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 25 4 0>, <&sdma 26 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| esai: esai@02024000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx35-esai"; |
| reg = <0x02024000 0x4000>; |
| interrupts = <0 51 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_ESAI_IPG>, |
| <&clks IMX6QDL_CLK_ESAI_MEM>, |
| <&clks IMX6QDL_CLK_ESAI_EXTAL>, |
| <&clks IMX6QDL_CLK_ESAI_IPG>, |
| <&clks IMX6QDL_CLK_SPBA>; |
| clock-names = "core", "mem", "extal", "fsys", "dma"; |
| dmas = <&sdma 23 21 0>, <&sdma 24 21 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| ssi1: ssi@02028000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx6q-ssi", |
| "fsl,imx51-ssi"; |
| reg = <0x02028000 0x4000>; |
| interrupts = <0 46 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_SSI1_IPG>, |
| <&clks IMX6QDL_CLK_SSI1>; |
| clock-names = "ipg", "baud"; |
| dmas = <&sdma 37 1 0>, |
| <&sdma 38 1 0>; |
| dma-names = "rx", "tx"; |
| fsl,fifo-depth = <15>; |
| status = "disabled"; |
| }; |
| |
| ssi2: ssi@0202c000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx6q-ssi", |
| "fsl,imx51-ssi"; |
| reg = <0x0202c000 0x4000>; |
| interrupts = <0 47 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_SSI2_IPG>, |
| <&clks IMX6QDL_CLK_SSI2>; |
| clock-names = "ipg", "baud"; |
| dmas = <&sdma 41 1 0>, |
| <&sdma 42 1 0>; |
| dma-names = "rx", "tx"; |
| fsl,fifo-depth = <15>; |
| status = "disabled"; |
| }; |
| |
| ssi3: ssi@02030000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx6q-ssi", |
| "fsl,imx51-ssi"; |
| reg = <0x02030000 0x4000>; |
| interrupts = <0 48 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_SSI3_IPG>, |
| <&clks IMX6QDL_CLK_SSI3>; |
| clock-names = "ipg", "baud"; |
| dmas = <&sdma 45 1 0>, |
| <&sdma 46 1 0>; |
| dma-names = "rx", "tx"; |
| fsl,fifo-depth = <15>; |
| status = "disabled"; |
| }; |
| |
| asrc: asrc@02034000 { |
| compatible = "fsl,imx53-asrc"; |
| reg = <0x02034000 0x4000>; |
| interrupts = <0 50 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_ASRC_IPG>, |
| <&clks IMX6QDL_CLK_ASRC_MEM>, <&clks 0>, |
| <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>, |
| <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>, |
| <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>, |
| <&clks IMX6QDL_CLK_ASRC>, <&clks 0>, <&clks 0>, |
| <&clks IMX6QDL_CLK_SPBA>; |
| clock-names = "mem", "ipg", "asrck_0", |
| "asrck_1", "asrck_2", "asrck_3", "asrck_4", |
| "asrck_5", "asrck_6", "asrck_7", "asrck_8", |
| "asrck_9", "asrck_a", "asrck_b", "asrck_c", |
| "asrck_d", "asrck_e", "asrck_f", "dma"; |
| dmas = <&sdma 17 23 1>, <&sdma 18 23 1>, <&sdma 19 23 1>, |
| <&sdma 20 23 1>, <&sdma 21 23 1>, <&sdma 22 23 1>; |
| dma-names = "rxa", "rxb", "rxc", |
| "txa", "txb", "txc"; |
| fsl,asrc-rate = <48000>; |
| fsl,asrc-width = <16>; |
| status = "okay"; |
| }; |
| |
| spba@0203c000 { |
| reg = <0x0203c000 0x4000>; |
| }; |
| }; |
| |
| vpu: vpu@02040000 { |
| compatible = "cnm,coda960"; |
| reg = <0x02040000 0x3c000>; |
| interrupts = <0 12 IRQ_TYPE_LEVEL_HIGH>, |
| <0 3 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "bit", "jpeg"; |
| clocks = <&clks IMX6QDL_CLK_VPU_AXI>, |
| <&clks IMX6QDL_CLK_MMDC_CH0_AXI>; |
| clock-names = "per", "ahb"; |
| power-domains = <&gpc 1>; |
| resets = <&src 1>; |
| iram = <&ocram>; |
| }; |
| |
| aipstz@0207c000 { /* AIPSTZ1 */ |
| reg = <0x0207c000 0x4000>; |
| }; |
| |
| pwm1: pwm@02080000 { |
| #pwm-cells = <2>; |
| compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm"; |
| reg = <0x02080000 0x4000>; |
| interrupts = <0 83 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_IPG>, |
| <&clks IMX6QDL_CLK_PWM1>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| pwm2: pwm@02084000 { |
| #pwm-cells = <2>; |
| compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm"; |
| reg = <0x02084000 0x4000>; |
| interrupts = <0 84 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_IPG>, |
| <&clks IMX6QDL_CLK_PWM2>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| pwm3: pwm@02088000 { |
| #pwm-cells = <2>; |
| compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm"; |
| reg = <0x02088000 0x4000>; |
| interrupts = <0 85 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_IPG>, |
| <&clks IMX6QDL_CLK_PWM3>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| pwm4: pwm@0208c000 { |
| #pwm-cells = <2>; |
| compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm"; |
| reg = <0x0208c000 0x4000>; |
| interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_IPG>, |
| <&clks IMX6QDL_CLK_PWM4>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| can1: flexcan@02090000 { |
| compatible = "fsl,imx6q-flexcan"; |
| reg = <0x02090000 0x4000>; |
| interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_CAN1_IPG>, |
| <&clks IMX6QDL_CLK_CAN1_SERIAL>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| can2: flexcan@02094000 { |
| compatible = "fsl,imx6q-flexcan"; |
| reg = <0x02094000 0x4000>; |
| interrupts = <0 111 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_CAN2_IPG>, |
| <&clks IMX6QDL_CLK_CAN2_SERIAL>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| gpt: gpt@02098000 { |
| compatible = "fsl,imx6q-gpt", "fsl,imx31-gpt"; |
| reg = <0x02098000 0x4000>; |
| interrupts = <0 55 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_GPT_IPG>, |
| <&clks IMX6QDL_CLK_GPT_IPG_PER>, |
| <&clks IMX6QDL_CLK_GPT_3M>; |
| clock-names = "ipg", "per", "osc_per"; |
| }; |
| |
| gpio1: gpio@0209c000 { |
| compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; |
| reg = <0x0209c000 0x4000>; |
| interrupts = <0 66 IRQ_TYPE_LEVEL_HIGH>, |
| <0 67 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio2: gpio@020a0000 { |
| compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; |
| reg = <0x020a0000 0x4000>; |
| interrupts = <0 68 IRQ_TYPE_LEVEL_HIGH>, |
| <0 69 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio3: gpio@020a4000 { |
| compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; |
| reg = <0x020a4000 0x4000>; |
| interrupts = <0 70 IRQ_TYPE_LEVEL_HIGH>, |
| <0 71 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio4: gpio@020a8000 { |
| compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; |
| reg = <0x020a8000 0x4000>; |
| interrupts = <0 72 IRQ_TYPE_LEVEL_HIGH>, |
| <0 73 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio5: gpio@020ac000 { |
| compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; |
| reg = <0x020ac000 0x4000>; |
| interrupts = <0 74 IRQ_TYPE_LEVEL_HIGH>, |
| <0 75 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio6: gpio@020b0000 { |
| compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; |
| reg = <0x020b0000 0x4000>; |
| interrupts = <0 76 IRQ_TYPE_LEVEL_HIGH>, |
| <0 77 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio7: gpio@020b4000 { |
| compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; |
| reg = <0x020b4000 0x4000>; |
| interrupts = <0 78 IRQ_TYPE_LEVEL_HIGH>, |
| <0 79 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| kpp: kpp@020b8000 { |
| compatible = "fsl,imx6q-kpp", "fsl,imx21-kpp"; |
| reg = <0x020b8000 0x4000>; |
| interrupts = <0 82 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_IPG>; |
| status = "disabled"; |
| }; |
| |
| wdog1: wdog@020bc000 { |
| compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt"; |
| reg = <0x020bc000 0x4000>; |
| interrupts = <0 80 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_DUMMY>; |
| }; |
| |
| wdog2: wdog@020c0000 { |
| compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt"; |
| reg = <0x020c0000 0x4000>; |
| interrupts = <0 81 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_DUMMY>; |
| status = "disabled"; |
| }; |
| |
| clks: ccm@020c4000 { |
| compatible = "fsl,imx6q-ccm"; |
| reg = <0x020c4000 0x4000>; |
| interrupts = <0 87 IRQ_TYPE_LEVEL_HIGH>, |
| <0 88 IRQ_TYPE_LEVEL_HIGH>; |
| #clock-cells = <1>; |
| }; |
| |
| anatop: anatop@020c8000 { |
| compatible = "fsl,imx6q-anatop", "syscon", "simple-bus"; |
| reg = <0x020c8000 0x1000>; |
| interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>, |
| <0 54 IRQ_TYPE_LEVEL_HIGH>, |
| <0 127 IRQ_TYPE_LEVEL_HIGH>; |
| |
| regulator-1p1@110 { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vdd1p1"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1375000>; |
| regulator-always-on; |
| anatop-reg-offset = <0x110>; |
| anatop-vol-bit-shift = <8>; |
| anatop-vol-bit-width = <5>; |
| anatop-min-bit-val = <4>; |
| anatop-min-voltage = <800000>; |
| anatop-max-voltage = <1375000>; |
| }; |
| |
| regulator-3p0@120 { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vdd3p0"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <3150000>; |
| regulator-always-on; |
| anatop-reg-offset = <0x120>; |
| anatop-vol-bit-shift = <8>; |
| anatop-vol-bit-width = <5>; |
| anatop-min-bit-val = <0>; |
| anatop-min-voltage = <2625000>; |
| anatop-max-voltage = <3400000>; |
| }; |
| |
| regulator-2p5@130 { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vdd2p5"; |
| regulator-min-microvolt = <2000000>; |
| regulator-max-microvolt = <2750000>; |
| regulator-always-on; |
| anatop-reg-offset = <0x130>; |
| anatop-vol-bit-shift = <8>; |
| anatop-vol-bit-width = <5>; |
| anatop-min-bit-val = <0>; |
| anatop-min-voltage = <2000000>; |
| anatop-max-voltage = <2750000>; |
| }; |
| |
| reg_arm: regulator-vddcore@140 { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vddarm"; |
| regulator-min-microvolt = <725000>; |
| regulator-max-microvolt = <1450000>; |
| regulator-always-on; |
| anatop-reg-offset = <0x140>; |
| anatop-vol-bit-shift = <0>; |
| anatop-vol-bit-width = <5>; |
| anatop-delay-reg-offset = <0x170>; |
| anatop-delay-bit-shift = <24>; |
| anatop-delay-bit-width = <2>; |
| anatop-min-bit-val = <1>; |
| anatop-min-voltage = <725000>; |
| anatop-max-voltage = <1450000>; |
| }; |
| |
| reg_pu: regulator-vddpu@140 { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vddpu"; |
| regulator-min-microvolt = <725000>; |
| regulator-max-microvolt = <1450000>; |
| regulator-enable-ramp-delay = <150>; |
| anatop-reg-offset = <0x140>; |
| anatop-vol-bit-shift = <9>; |
| anatop-vol-bit-width = <5>; |
| anatop-delay-reg-offset = <0x170>; |
| anatop-delay-bit-shift = <26>; |
| anatop-delay-bit-width = <2>; |
| anatop-min-bit-val = <1>; |
| anatop-min-voltage = <725000>; |
| anatop-max-voltage = <1450000>; |
| }; |
| |
| reg_soc: regulator-vddsoc@140 { |
| compatible = "fsl,anatop-regulator"; |
| regulator-name = "vddsoc"; |
| regulator-min-microvolt = <725000>; |
| regulator-max-microvolt = <1450000>; |
| regulator-always-on; |
| anatop-reg-offset = <0x140>; |
| anatop-vol-bit-shift = <18>; |
| anatop-vol-bit-width = <5>; |
| anatop-delay-reg-offset = <0x170>; |
| anatop-delay-bit-shift = <28>; |
| anatop-delay-bit-width = <2>; |
| anatop-min-bit-val = <1>; |
| anatop-min-voltage = <725000>; |
| anatop-max-voltage = <1450000>; |
| }; |
| }; |
| |
| tempmon: tempmon { |
| compatible = "fsl,imx6q-tempmon"; |
| interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>; |
| fsl,tempmon = <&anatop>; |
| fsl,tempmon-data = <&ocotp>; |
| clocks = <&clks IMX6QDL_CLK_PLL3_USB_OTG>; |
| }; |
| |
| usbphy1: usbphy@020c9000 { |
| compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; |
| reg = <0x020c9000 0x1000>; |
| interrupts = <0 44 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_USBPHY1>; |
| fsl,anatop = <&anatop>; |
| }; |
| |
| usbphy2: usbphy@020ca000 { |
| compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; |
| reg = <0x020ca000 0x1000>; |
| interrupts = <0 45 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_USBPHY2>; |
| fsl,anatop = <&anatop>; |
| }; |
| |
| snvs: snvs@020cc000 { |
| compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd"; |
| reg = <0x020cc000 0x4000>; |
| |
| snvs_rtc: snvs-rtc-lp { |
| compatible = "fsl,sec-v4.0-mon-rtc-lp"; |
| regmap = <&snvs>; |
| offset = <0x34>; |
| interrupts = <0 19 IRQ_TYPE_LEVEL_HIGH>, |
| <0 20 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| snvs_poweroff: snvs-poweroff { |
| compatible = "syscon-poweroff"; |
| regmap = <&snvs>; |
| offset = <0x38>; |
| mask = <0x60>; |
| status = "disabled"; |
| }; |
| }; |
| |
| epit1: epit@020d0000 { /* EPIT1 */ |
| reg = <0x020d0000 0x4000>; |
| interrupts = <0 56 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| epit2: epit@020d4000 { /* EPIT2 */ |
| reg = <0x020d4000 0x4000>; |
| interrupts = <0 57 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| src: src@020d8000 { |
| compatible = "fsl,imx6q-src", "fsl,imx51-src"; |
| reg = <0x020d8000 0x4000>; |
| interrupts = <0 91 IRQ_TYPE_LEVEL_HIGH>, |
| <0 96 IRQ_TYPE_LEVEL_HIGH>; |
| #reset-cells = <1>; |
| }; |
| |
| gpc: gpc@020dc000 { |
| compatible = "fsl,imx6q-gpc"; |
| reg = <0x020dc000 0x4000>; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>, |
| <0 90 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-parent = <&intc>; |
| pu-supply = <®_pu>; |
| clocks = <&clks IMX6QDL_CLK_GPU3D_CORE>, |
| <&clks IMX6QDL_CLK_GPU3D_SHADER>, |
| <&clks IMX6QDL_CLK_GPU2D_CORE>, |
| <&clks IMX6QDL_CLK_GPU2D_AXI>, |
| <&clks IMX6QDL_CLK_OPENVG_AXI>, |
| <&clks IMX6QDL_CLK_VPU_AXI>; |
| #power-domain-cells = <1>; |
| }; |
| |
| gpr: iomuxc-gpr@020e0000 { |
| compatible = "fsl,imx6q-iomuxc-gpr", "syscon"; |
| reg = <0x020e0000 0x38>; |
| }; |
| |
| iomuxc: iomuxc@020e0000 { |
| compatible = "fsl,imx6dl-iomuxc", "fsl,imx6q-iomuxc"; |
| reg = <0x020e0000 0x4000>; |
| }; |
| |
| ldb: ldb@020e0008 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6q-ldb", "fsl,imx53-ldb"; |
| gpr = <&gpr>; |
| status = "disabled"; |
| |
| lvds-channel@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| status = "disabled"; |
| |
| port@0 { |
| reg = <0>; |
| |
| lvds0_mux_0: endpoint { |
| remote-endpoint = <&ipu1_di0_lvds0>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| lvds0_mux_1: endpoint { |
| remote-endpoint = <&ipu1_di1_lvds0>; |
| }; |
| }; |
| }; |
| |
| lvds-channel@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| status = "disabled"; |
| |
| port@0 { |
| reg = <0>; |
| |
| lvds1_mux_0: endpoint { |
| remote-endpoint = <&ipu1_di0_lvds1>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| lvds1_mux_1: endpoint { |
| remote-endpoint = <&ipu1_di1_lvds1>; |
| }; |
| }; |
| }; |
| }; |
| |
| dcic1: dcic@020e4000 { |
| reg = <0x020e4000 0x4000>; |
| interrupts = <0 124 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| dcic2: dcic@020e8000 { |
| reg = <0x020e8000 0x4000>; |
| interrupts = <0 125 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| sdma: sdma@020ec000 { |
| compatible = "fsl,imx6q-sdma", "fsl,imx35-sdma"; |
| reg = <0x020ec000 0x4000>; |
| interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_SDMA>, |
| <&clks IMX6QDL_CLK_SDMA>; |
| clock-names = "ipg", "ahb"; |
| #dma-cells = <3>; |
| fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6q.bin"; |
| }; |
| }; |
| |
| aips-bus@02100000 { /* AIPS2 */ |
| compatible = "fsl,aips-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x02100000 0x100000>; |
| ranges; |
| |
| crypto: caam@2100000 { |
| compatible = "fsl,sec-v4.0"; |
| fsl,sec-era = <4>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x2100000 0x10000>; |
| ranges = <0 0x2100000 0x10000>; |
| interrupt-parent = <&intc>; |
| clocks = <&clks IMX6QDL_CLK_CAAM_MEM>, |
| <&clks IMX6QDL_CLK_CAAM_ACLK>, |
| <&clks IMX6QDL_CLK_CAAM_IPG>, |
| <&clks IMX6QDL_CLK_EIM_SLOW>; |
| clock-names = "mem", "aclk", "ipg", "emi_slow"; |
| |
| sec_jr0: jr0@1000 { |
| compatible = "fsl,sec-v4.0-job-ring"; |
| reg = <0x1000 0x1000>; |
| interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| sec_jr1: jr1@2000 { |
| compatible = "fsl,sec-v4.0-job-ring"; |
| reg = <0x2000 0x1000>; |
| interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| aipstz@0217c000 { /* AIPSTZ2 */ |
| reg = <0x0217c000 0x4000>; |
| }; |
| |
| usbotg: usb@02184000 { |
| compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; |
| reg = <0x02184000 0x200>; |
| interrupts = <0 43 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_USBOH3>; |
| fsl,usbphy = <&usbphy1>; |
| fsl,usbmisc = <&usbmisc 0>; |
| status = "disabled"; |
| }; |
| |
| usbh1: usb@02184200 { |
| compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; |
| reg = <0x02184200 0x200>; |
| interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_USBOH3>; |
| fsl,usbphy = <&usbphy2>; |
| fsl,usbmisc = <&usbmisc 1>; |
| dr_mode = "host"; |
| status = "disabled"; |
| }; |
| |
| usbh2: usb@02184400 { |
| compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; |
| reg = <0x02184400 0x200>; |
| interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_USBOH3>; |
| fsl,usbmisc = <&usbmisc 2>; |
| dr_mode = "host"; |
| status = "disabled"; |
| }; |
| |
| usbh3: usb@02184600 { |
| compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; |
| reg = <0x02184600 0x200>; |
| interrupts = <0 42 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_USBOH3>; |
| fsl,usbmisc = <&usbmisc 3>; |
| dr_mode = "host"; |
| status = "disabled"; |
| }; |
| |
| usbmisc: usbmisc@02184800 { |
| #index-cells = <1>; |
| compatible = "fsl,imx6q-usbmisc"; |
| reg = <0x02184800 0x200>; |
| clocks = <&clks IMX6QDL_CLK_USBOH3>; |
| }; |
| |
| fec: ethernet@02188000 { |
| compatible = "fsl,imx6q-fec"; |
| reg = <0x02188000 0x4000>; |
| interrupts-extended = |
| <&intc 0 118 IRQ_TYPE_LEVEL_HIGH>, |
| <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_ENET>, |
| <&clks IMX6QDL_CLK_ENET>, |
| <&clks IMX6QDL_CLK_ENET_REF>; |
| clock-names = "ipg", "ahb", "ptp"; |
| status = "disabled"; |
| }; |
| |
| mlb@0218c000 { |
| reg = <0x0218c000 0x4000>; |
| interrupts = <0 53 IRQ_TYPE_LEVEL_HIGH>, |
| <0 117 IRQ_TYPE_LEVEL_HIGH>, |
| <0 126 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| usdhc1: usdhc@02190000 { |
| compatible = "fsl,imx6q-usdhc"; |
| reg = <0x02190000 0x4000>; |
| interrupts = <0 22 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_USDHC1>, |
| <&clks IMX6QDL_CLK_USDHC1>, |
| <&clks IMX6QDL_CLK_USDHC1>; |
| clock-names = "ipg", "ahb", "per"; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| usdhc2: usdhc@02194000 { |
| compatible = "fsl,imx6q-usdhc"; |
| reg = <0x02194000 0x4000>; |
| interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_USDHC2>, |
| <&clks IMX6QDL_CLK_USDHC2>, |
| <&clks IMX6QDL_CLK_USDHC2>; |
| clock-names = "ipg", "ahb", "per"; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| usdhc3: usdhc@02198000 { |
| compatible = "fsl,imx6q-usdhc"; |
| reg = <0x02198000 0x4000>; |
| interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_USDHC3>, |
| <&clks IMX6QDL_CLK_USDHC3>, |
| <&clks IMX6QDL_CLK_USDHC3>; |
| clock-names = "ipg", "ahb", "per"; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| usdhc4: usdhc@0219c000 { |
| compatible = "fsl,imx6q-usdhc"; |
| reg = <0x0219c000 0x4000>; |
| interrupts = <0 25 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_USDHC4>, |
| <&clks IMX6QDL_CLK_USDHC4>, |
| <&clks IMX6QDL_CLK_USDHC4>; |
| clock-names = "ipg", "ahb", "per"; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@021a0000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6q-i2c", "fsl,imx21-i2c"; |
| reg = <0x021a0000 0x4000>; |
| interrupts = <0 36 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_I2C1>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@021a4000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6q-i2c", "fsl,imx21-i2c"; |
| reg = <0x021a4000 0x4000>; |
| interrupts = <0 37 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_I2C2>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@021a8000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6q-i2c", "fsl,imx21-i2c"; |
| reg = <0x021a8000 0x4000>; |
| interrupts = <0 38 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_I2C3>; |
| status = "disabled"; |
| }; |
| |
| romcp@021ac000 { |
| reg = <0x021ac000 0x4000>; |
| }; |
| |
| mmdc0: mmdc@021b0000 { /* MMDC0 */ |
| compatible = "fsl,imx6q-mmdc"; |
| reg = <0x021b0000 0x4000>; |
| }; |
| |
| mmdc1: mmdc@021b4000 { /* MMDC1 */ |
| reg = <0x021b4000 0x4000>; |
| }; |
| |
| weim: weim@021b8000 { |
| compatible = "fsl,imx6q-weim"; |
| reg = <0x021b8000 0x4000>; |
| interrupts = <0 14 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_EIM_SLOW>; |
| }; |
| |
| ocotp: ocotp@021bc000 { |
| compatible = "fsl,imx6q-ocotp", "syscon"; |
| reg = <0x021bc000 0x4000>; |
| }; |
| |
| tzasc@021d0000 { /* TZASC1 */ |
| reg = <0x021d0000 0x4000>; |
| interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| tzasc@021d4000 { /* TZASC2 */ |
| reg = <0x021d4000 0x4000>; |
| interrupts = <0 109 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| audmux: audmux@021d8000 { |
| compatible = "fsl,imx6q-audmux", "fsl,imx31-audmux"; |
| reg = <0x021d8000 0x4000>; |
| status = "disabled"; |
| }; |
| |
| mipi_csi: mipi@021dc000 { |
| reg = <0x021dc000 0x4000>; |
| }; |
| |
| mipi_dsi: mipi@021e0000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x021e0000 0x4000>; |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| mipi_mux_0: endpoint { |
| remote-endpoint = <&ipu1_di0_mipi>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| mipi_mux_1: endpoint { |
| remote-endpoint = <&ipu1_di1_mipi>; |
| }; |
| }; |
| }; |
| }; |
| |
| vdoa@021e4000 { |
| reg = <0x021e4000 0x4000>; |
| interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| uart2: serial@021e8000 { |
| compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; |
| reg = <0x021e8000 0x4000>; |
| interrupts = <0 27 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_UART_IPG>, |
| <&clks IMX6QDL_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 27 4 0>, <&sdma 28 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart3: serial@021ec000 { |
| compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; |
| reg = <0x021ec000 0x4000>; |
| interrupts = <0 28 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_UART_IPG>, |
| <&clks IMX6QDL_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 29 4 0>, <&sdma 30 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@021f0000 { |
| compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; |
| reg = <0x021f0000 0x4000>; |
| interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_UART_IPG>, |
| <&clks IMX6QDL_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 31 4 0>, <&sdma 32 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart5: serial@021f4000 { |
| compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; |
| reg = <0x021f4000 0x4000>; |
| interrupts = <0 30 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_UART_IPG>, |
| <&clks IMX6QDL_CLK_UART_SERIAL>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma 33 4 0>, <&sdma 34 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| }; |
| |
| ipu1: ipu@02400000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx6q-ipu"; |
| reg = <0x02400000 0x400000>; |
| interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>, |
| <0 5 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX6QDL_CLK_IPU1>, |
| <&clks IMX6QDL_CLK_IPU1_DI0>, |
| <&clks IMX6QDL_CLK_IPU1_DI1>; |
| clock-names = "bus", "di0", "di1"; |
| resets = <&src 2>; |
| |
| ipu1_csi0: port@0 { |
| reg = <0>; |
| }; |
| |
| ipu1_csi1: port@1 { |
| reg = <1>; |
| }; |
| |
| ipu1_di0: port@2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <2>; |
| |
| ipu1_di0_disp0: endpoint@0 { |
| }; |
| |
| ipu1_di0_hdmi: endpoint@1 { |
| remote-endpoint = <&hdmi_mux_0>; |
| }; |
| |
| ipu1_di0_mipi: endpoint@2 { |
| remote-endpoint = <&mipi_mux_0>; |
| }; |
| |
| ipu1_di0_lvds0: endpoint@3 { |
| remote-endpoint = <&lvds0_mux_0>; |
| }; |
| |
| ipu1_di0_lvds1: endpoint@4 { |
| remote-endpoint = <&lvds1_mux_0>; |
| }; |
| }; |
| |
| ipu1_di1: port@3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <3>; |
| |
| ipu1_di0_disp1: endpoint@0 { |
| }; |
| |
| ipu1_di1_hdmi: endpoint@1 { |
| remote-endpoint = <&hdmi_mux_1>; |
| }; |
| |
| ipu1_di1_mipi: endpoint@2 { |
| remote-endpoint = <&mipi_mux_1>; |
| }; |
| |
| ipu1_di1_lvds0: endpoint@3 { |
| remote-endpoint = <&lvds0_mux_1>; |
| }; |
| |
| ipu1_di1_lvds1: endpoint@4 { |
| remote-endpoint = <&lvds1_mux_1>; |
| }; |
| }; |
| }; |
| }; |
| }; |
