| /* |
| * DO NOT EDIT THIS FILE |
| * This file is under version control at |
| * svn://sources.blackfin.uclinux.org/toolchain/trunk/proc-defs/header-frags/ |
| * and can be replaced with that version at any time |
| * DO NOT EDIT THIS FILE |
| * |
| * Copyright 2004-2011 Analog Devices Inc. |
| * Licensed under the Clear BSD license. |
| */ |
| |
| /* This file should be up to date with: |
| * - Revision F, 05/23/2011; ADSP-BF526 Blackfin Processor Anomaly List |
| * - Revision I, 05/23/2011; ADSP-BF527 Blackfin Processor Anomaly List |
| */ |
| |
| #ifndef _MACH_ANOMALY_H_ |
| #define _MACH_ANOMALY_H_ |
| |
| /* We do not support old silicon - sorry */ |
| #if __SILICON_REVISION__ < 0 |
| # error will not work on BF526/BF527 silicon version |
| #endif |
| |
| #if defined(__ADSPBF522__) || defined(__ADSPBF524__) || defined(__ADSPBF526__) |
| # define ANOMALY_BF526 1 |
| #else |
| # define ANOMALY_BF526 0 |
| #endif |
| #if defined(__ADSPBF523__) || defined(__ADSPBF525__) || defined(__ADSPBF527__) |
| # define ANOMALY_BF527 1 |
| #else |
| # define ANOMALY_BF527 0 |
| #endif |
| |
| #define _ANOMALY_BF526(rev526) (ANOMALY_BF526 && __SILICON_REVISION__ rev526) |
| #define _ANOMALY_BF527(rev527) (ANOMALY_BF527 && __SILICON_REVISION__ rev527) |
| #define _ANOMALY_BF526_BF527(rev526, rev527) (_ANOMALY_BF526(rev526) || _ANOMALY_BF527(rev527)) |
| |
| /* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot2 Not Supported */ |
| #define ANOMALY_05000074 (1) |
| /* DMA_RUN Bit Is Not Valid after a Peripheral Receive Channel DMA Stops */ |
| #define ANOMALY_05000119 (1) |
| /* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */ |
| #define ANOMALY_05000122 (1) |
| /* False Hardware Error from an Access in the Shadow of a Conditional Branch */ |
| #define ANOMALY_05000245 (1) |
| /* Incorrect Timer Pulse Width in Single-Shot PWM_OUT Mode with External Clock */ |
| #define ANOMALY_05000254 (1) |
| /* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */ |
| #define ANOMALY_05000265 (1) |
| /* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */ |
| #define ANOMALY_05000310 (1) |
| /* PPI Is Level-Sensitive on First Transfer In Single Frame Sync Modes */ |
| #define ANOMALY_05000313 (_ANOMALY_BF526_BF527(< 1, < 2)) |
| /* Incorrect Access of OTP_STATUS During otp_write() Function */ |
| #define ANOMALY_05000328 (_ANOMALY_BF527(< 2)) |
| /* Host DMA Boot Modes Are Not Functional */ |
| #define ANOMALY_05000330 (_ANOMALY_BF527(< 2)) |
| /* Disallowed Configuration Prevents Subsequent Allowed Configuration on Host DMA Port */ |
| #define ANOMALY_05000337 (_ANOMALY_BF527(< 2)) |
| /* Ethernet MAC MDIO Reads Do Not Meet IEEE Specification */ |
| #define ANOMALY_05000341 (_ANOMALY_BF527(< 2)) |
| /* TWI May Not Operate Correctly Under Certain Signal Termination Conditions */ |
| #define ANOMALY_05000342 (_ANOMALY_BF527(< 2)) |
| /* USB Calibration Value Is Not Initialized */ |
| #define ANOMALY_05000346 (_ANOMALY_BF526_BF527(< 1, < 2)) |
| /* USB Calibration Value to use */ |
| #define ANOMALY_05000346_value 0xE510 |
| /* Preboot Routine Incorrectly Alters Reset Value of USB Register */ |
| #define ANOMALY_05000347 (_ANOMALY_BF527(< 2)) |
| /* Security Features Are Not Functional */ |
| #define ANOMALY_05000348 (_ANOMALY_BF527(< 1)) |
| /* bfrom_SysControl() Firmware Function Performs Improper System Reset */ |
| #define ANOMALY_05000353 (_ANOMALY_BF526(< 1)) |
| /* Regulator Programming Blocked when Hibernate Wakeup Source Remains Active */ |
| #define ANOMALY_05000355 (_ANOMALY_BF527(< 2)) |
| /* Serial Port (SPORT) Multichannel Transmit Failure when Channel 0 Is Disabled */ |
| #define ANOMALY_05000357 (_ANOMALY_BF527(< 2)) |
| /* Incorrect Revision Number in DSPID Register */ |
| #define ANOMALY_05000364 (_ANOMALY_BF527(== 1)) |
| /* PPI Underflow Error Goes Undetected in ITU-R 656 Mode */ |
| #define ANOMALY_05000366 (1) |
| /* Incorrect Default CSEL Value in PLL_DIV */ |
| #define ANOMALY_05000368 (_ANOMALY_BF527(< 2)) |
| /* Possible RETS Register Corruption when Subroutine Is under 5 Cycles in Duration */ |
| #define ANOMALY_05000371 (_ANOMALY_BF527(< 2)) |
| /* Authentication Fails To Initiate */ |
| #define ANOMALY_05000376 (_ANOMALY_BF527(< 2)) |
| /* Data Read From L3 Memory by USB DMA May be Corrupted */ |
| #define ANOMALY_05000380 (_ANOMALY_BF527(< 2)) |
| /* 8-Bit NAND Flash Boot Mode Not Functional */ |
| #define ANOMALY_05000382 (_ANOMALY_BF526_BF527(< 1, < 2)) |
| /* Boot from OTP Memory Not Functional */ |
| #define ANOMALY_05000385 (_ANOMALY_BF527(< 2)) |
| /* bfrom_SysControl() Firmware Routine Not Functional */ |
| #define ANOMALY_05000386 (_ANOMALY_BF527(< 2)) |
| /* Programmable Preboot Settings Not Functional */ |
| #define ANOMALY_05000387 (_ANOMALY_BF527(< 2)) |
| /* CRC32 Checksum Support Not Functional */ |
| #define ANOMALY_05000388 (_ANOMALY_BF526_BF527(< 1, < 2)) |
| /* Reset Vector Must Not Be in SDRAM Memory Space */ |
| #define ANOMALY_05000389 (_ANOMALY_BF527(< 2)) |
| /* pTempCurrent Not Present in ADI_BOOT_DATA Structure */ |
| #define ANOMALY_05000392 (_ANOMALY_BF527(< 2)) |
| /* Deprecated Value of dTempByteCount in ADI_BOOT_DATA Structure */ |
| #define ANOMALY_05000393 (_ANOMALY_BF527(< 2)) |
| /* Log Buffer Not Functional */ |
| #define ANOMALY_05000394 (_ANOMALY_BF527(< 2)) |
| /* Hook Routine Not Functional */ |
| #define ANOMALY_05000395 (_ANOMALY_BF527(< 2)) |
| /* Header Indirect Bit Not Functional */ |
| #define ANOMALY_05000396 (_ANOMALY_BF527(< 2)) |
| /* BK_ONES, BK_ZEROS, and BK_DATECODE Constants Not Functional */ |
| #define ANOMALY_05000397 (_ANOMALY_BF527(< 2)) |
| /* SWRESET, DFRESET and WDRESET Bits in the SYSCR Register Not Functional */ |
| #define ANOMALY_05000398 (_ANOMALY_BF527(< 2)) |
| /* BCODE_NOBOOT in BCODE Field of SYSCR Register Not Functional */ |
| #define ANOMALY_05000399 (_ANOMALY_BF527(< 2)) |
| /* PPI Data Signals D0 and D8 do not Tristate After Disabling PPI */ |
| #define ANOMALY_05000401 (_ANOMALY_BF526_BF527(< 1, < 2)) |
| /* Level-Sensitive External GPIO Wakeups May Cause Indefinite Stall */ |
| #define ANOMALY_05000403 (_ANOMALY_BF526_BF527(< 1, < 2)) |
| /* Lockbox SESR Disallows Certain User Interrupts */ |
| #define ANOMALY_05000404 (_ANOMALY_BF526_BF527(< 1, < 2)) |
| /* Lockbox SESR Firmware Does Not Save/Restore Full Context */ |
| #define ANOMALY_05000405 (1) |
| /* Lockbox SESR Firmware Arguments Are Not Retained After First Initialization */ |
| #define ANOMALY_05000407 (_ANOMALY_BF526_BF527(< 1, < 2)) |
| /* Lockbox Firmware Memory Cleanup Routine Does not Clear Registers */ |
| #define ANOMALY_05000408 (1) |
| /* Lockbox firmware leaves MDMA0 channel enabled */ |
| #define ANOMALY_05000409 (_ANOMALY_BF526_BF527(< 1, < 2)) |
| /* Incorrect Default Internal Voltage Regulator Setting */ |
| #define ANOMALY_05000410 (_ANOMALY_BF527(< 2)) |
| /* bfrom_SysControl() Firmware Function Cannot be Used to Enter Power Saving Modes */ |
| #define ANOMALY_05000411 (_ANOMALY_BF526(< 1)) |
| /* OTP_CHECK_FOR_PREV_WRITE Bit is Not Functional in bfrom_OtpWrite() API */ |
| #define ANOMALY_05000414 (_ANOMALY_BF526_BF527(< 1, < 2)) |
| /* DEB2_URGENT Bit Not Functional */ |
| #define ANOMALY_05000415 (_ANOMALY_BF526_BF527(< 1, < 2)) |
| /* Speculative Fetches Can Cause Undesired External FIFO Operations */ |
| #define ANOMALY_05000416 (1) |
| /* SPORT0 Ignores External TSCLK0 on PG14 When TMR6 is an Output */ |
| #define ANOMALY_05000417 (_ANOMALY_BF527(< 2)) |
| /* PPI Timing Requirements tSFSPE and tHFSPE Do Not Meet Data Sheet Specifications */ |
| #define ANOMALY_05000418 (_ANOMALY_BF526_BF527(< 1, < 2)) |
| /* USB PLL_STABLE Bit May Not Accurately Reflect the USB PLL's Status */ |
| #define ANOMALY_05000420 (_ANOMALY_BF526_BF527(< 1, < 2)) |
| /* TWI Fall Time (Tof) May Violate the Minimum I2C Specification */ |
| #define ANOMALY_05000421 (1) |
| /* TWI Input Capacitance (Ci) May Violate the Maximum I2C Specification */ |
| #define ANOMALY_05000422 (_ANOMALY_BF526_BF527(> 0, > 1)) |
| /* Certain Ethernet Frames With Errors are Misclassified in RMII Mode */ |
| #define ANOMALY_05000423 (_ANOMALY_BF526_BF527(< 1, < 2)) |
| /* Internal Voltage Regulator Not Trimmed */ |
| #define ANOMALY_05000424 (_ANOMALY_BF527(< 2)) |
| /* Multichannel SPORT Channel Misalignment Under Specific Configuration */ |
| #define ANOMALY_05000425 (_ANOMALY_BF526_BF527(< 1, < 2)) |
| /* Speculative Fetches of Indirect-Pointer Instructions Can Cause False Hardware Errors */ |
| #define ANOMALY_05000426 (1) |
| /* WB_EDGE Bit in NFC_IRQSTAT Incorrectly Reflects Buffer Status Instead of IRQ Status */ |
| #define ANOMALY_05000429 (_ANOMALY_BF526_BF527(< 1, < 2)) |
| /* Software System Reset Corrupts PLL_LOCKCNT Register */ |
| #define ANOMALY_05000430 (_ANOMALY_BF527(> 1)) |
| /* Incorrect Use of Stack in Lockbox Firmware During Authentication */ |
| #define ANOMALY_05000431 (1) |
| /* bfrom_SysControl() Does Not Clear SIC_IWR1 Before Executing PLL Programming Sequence */ |
| #define ANOMALY_05000432 (_ANOMALY_BF526(< 1)) |
| /* SW Breakpoints Ignored Upon Return From Lockbox Authentication */ |
| #define ANOMALY_05000434 (1) |
| /* Certain SIC Registers are not Reset After Soft or Core Double Fault Reset */ |
| #define ANOMALY_05000435 (_ANOMALY_BF526_BF527(< 1, >= 0)) |
| /* Preboot Cannot be Used to Alter the PLL_DIV Register */ |
| #define ANOMALY_05000439 (_ANOMALY_BF526_BF527(< 1, >= 0)) |
| /* bfrom_SysControl() Cannot be Used to Write the PLL_DIV Register */ |
| #define ANOMALY_05000440 (_ANOMALY_BF526_BF527(< 1, >= 0)) |
| /* OTP Write Accesses Not Supported */ |
| #define ANOMALY_05000442 (_ANOMALY_BF527(< 1)) |
| /* IFLUSH Instruction at End of Hardware Loop Causes Infinite Stall */ |
| #define ANOMALY_05000443 (1) |
| /* The WURESET Bit in the SYSCR Register is not Functional */ |
| #define ANOMALY_05000445 (_ANOMALY_BF527(>= 0)) |
| /* USB DMA Short Packet Data Corruption */ |
| #define ANOMALY_05000450 (1) |
| /* BCODE_QUICKBOOT, BCODE_ALLBOOT, and BCODE_FULLBOOT Settings in SYSCR Register Not Functional */ |
| #define ANOMALY_05000451 (_ANOMALY_BF527(>= 0)) |
| /* Incorrect Default Hysteresis Setting for RESET, NMI, and BMODE Signals */ |
| #define ANOMALY_05000452 (_ANOMALY_BF526_BF527(< 1, >= 0)) |
| /* USB Receive Interrupt Is Not Generated in DMA Mode 1 */ |
| #define ANOMALY_05000456 (1) |
| /* Host DMA Port Responds to Certain Bus Activity Without HOST_CE Assertion */ |
| #define ANOMALY_05000457 (1) |
| /* USB DMA Mode 1 Failure When Multiple USB DMA Channels Are Concurrently Enabled */ |
| #define ANOMALY_05000460 (1) |
| /* False Hardware Error when RETI Points to Invalid Memory */ |
| #define ANOMALY_05000461 (1) |
| /* Synchronization Problem at Startup May Cause SPORT Transmit Channels to Misalign */ |
| #define ANOMALY_05000462 (1) |
| /* USB Rx DMA Hang */ |
| #define ANOMALY_05000465 (1) |
| /* TxPktRdy Bit Not Set for Transmit Endpoint When Core and DMA Access USB Endpoint FIFOs Simultaneously */ |
| #define ANOMALY_05000466 (1) |
| /* Possible USB RX Data Corruption When Control & Data EP FIFOs are Accessed via the Core */ |
| #define ANOMALY_05000467 (1) |
| /* PLL Latches Incorrect Settings During Reset */ |
| #define ANOMALY_05000469 (1) |
| /* Incorrect Default MSEL Value in PLL_CTL */ |
| #define ANOMALY_05000472 (_ANOMALY_BF526(>= 0)) |
| /* Interrupted SPORT Receive Data Register Read Results In Underflow when SLEN > 15 */ |
| #define ANOMALY_05000473 (1) |
| /* Possible Lockup Condition when Modifying PLL from External Memory */ |
| #define ANOMALY_05000475 (1) |
| /* TESTSET Instruction Cannot Be Interrupted */ |
| #define ANOMALY_05000477 (1) |
| /* Reads of ITEST_COMMAND and ITEST_DATA Registers Cause Cache Corruption */ |
| #define ANOMALY_05000481 (1) |
| /* Possible USB Data Corruption When Multiple Endpoints Are Accessed by the Core */ |
| #define ANOMALY_05000483 (1) |
| /* PLL_CTL Change Using bfrom_SysControl() Can Result in Processor Overclocking */ |
| #define ANOMALY_05000485 (_ANOMALY_BF526_BF527(< 2, >= 0)) |
| /* The CODEC Zero-Cross Detect Feature is not Functional */ |
| #define ANOMALY_05000487 (1) |
| /* SPI Master Boot Can Fail Under Certain Conditions */ |
| #define ANOMALY_05000490 (1) |
| /* Instruction Memory Stalls Can Cause IFLUSH to Fail */ |
| #define ANOMALY_05000491 (1) |
| /* EXCPT Instruction May Be Lost If NMI Happens Simultaneously */ |
| #define ANOMALY_05000494 (1) |
| /* CNT_COMMAND Functionality Depends on CNT_IMASK Configuration */ |
| #define ANOMALY_05000498 (1) |
| /* RXS Bit in SPI_STAT May Become Stuck In RX DMA Modes */ |
| #define ANOMALY_05000501 (1) |
| |
| /* Anomalies that don't exist on this proc */ |
| #define ANOMALY_05000099 (0) |
| #define ANOMALY_05000120 (0) |
| #define ANOMALY_05000125 (0) |
| #define ANOMALY_05000149 (0) |
| #define ANOMALY_05000158 (0) |
| #define ANOMALY_05000171 (0) |
| #define ANOMALY_05000179 (0) |
| #define ANOMALY_05000182 (0) |
| #define ANOMALY_05000183 (0) |
| #define ANOMALY_05000189 (0) |
| #define ANOMALY_05000198 (0) |
| #define ANOMALY_05000202 (0) |
| #define ANOMALY_05000215 (0) |
| #define ANOMALY_05000219 (0) |
| #define ANOMALY_05000220 (0) |
| #define ANOMALY_05000227 (0) |
| #define ANOMALY_05000230 (0) |
| #define ANOMALY_05000231 (0) |
| #define ANOMALY_05000233 (0) |
| #define ANOMALY_05000234 (0) |
| #define ANOMALY_05000242 (0) |
| #define ANOMALY_05000244 (0) |
| #define ANOMALY_05000248 (0) |
| #define ANOMALY_05000250 (0) |
| #define ANOMALY_05000257 (0) |
| #define ANOMALY_05000261 (0) |
| #define ANOMALY_05000263 (0) |
| #define ANOMALY_05000266 (0) |
| #define ANOMALY_05000273 (0) |
| #define ANOMALY_05000274 (0) |
| #define ANOMALY_05000278 (0) |
| #define ANOMALY_05000281 (0) |
| #define ANOMALY_05000283 (0) |
| #define ANOMALY_05000285 (0) |
| #define ANOMALY_05000287 (0) |
| #define ANOMALY_05000301 (0) |
| #define ANOMALY_05000305 (0) |
| #define ANOMALY_05000307 (0) |
| #define ANOMALY_05000311 (0) |
| #define ANOMALY_05000312 (0) |
| #define ANOMALY_05000315 (0) |
| #define ANOMALY_05000323 (0) |
| #define ANOMALY_05000362 (1) |
| #define ANOMALY_05000363 (0) |
| #define ANOMALY_05000383 (0) |
| #define ANOMALY_05000400 (0) |
| #define ANOMALY_05000402 (0) |
| #define ANOMALY_05000412 (0) |
| #define ANOMALY_05000447 (0) |
| #define ANOMALY_05000448 (0) |
| #define ANOMALY_05000474 (0) |
| #define ANOMALY_05000480 (0) |
| #define ANOMALY_16000030 (0) |
| |
| #endif |