| perf-list(1) |
| ============ |
| |
| NAME |
| ---- |
| perf-list - List all symbolic event types |
| |
| SYNOPSIS |
| -------- |
| [verse] |
| 'perf list' [hw|sw|cache|tracepoint|pmu|event_glob] |
| |
| DESCRIPTION |
| ----------- |
| This command displays the symbolic event types which can be selected in the |
| various perf commands with the -e option. |
| |
| [[EVENT_MODIFIERS]] |
| EVENT MODIFIERS |
| --------------- |
| |
| Events can optionally have a modifier by appending a colon and one or |
| more modifiers. Modifiers allow the user to restrict the events to be |
| counted. The following modifiers exist: |
| |
| u - user-space counting |
| k - kernel counting |
| h - hypervisor counting |
| I - non idle counting |
| G - guest counting (in KVM guests) |
| H - host counting (not in KVM guests) |
| p - precise level |
| P - use maximum detected precise level |
| S - read sample value (PERF_SAMPLE_READ) |
| D - pin the event to the PMU |
| |
| The 'p' modifier can be used for specifying how precise the instruction |
| address should be. The 'p' modifier can be specified multiple times: |
| |
| 0 - SAMPLE_IP can have arbitrary skid |
| 1 - SAMPLE_IP must have constant skid |
| 2 - SAMPLE_IP requested to have 0 skid |
| 3 - SAMPLE_IP must have 0 skid |
| |
| For Intel systems precise event sampling is implemented with PEBS |
| which supports up to precise-level 2. |
| |
| On AMD systems it is implemented using IBS (up to precise-level 2). |
| The precise modifier works with event types 0x76 (cpu-cycles, CPU |
| clocks not halted) and 0xC1 (micro-ops retired). Both events map to |
| IBS execution sampling (IBS op) with the IBS Op Counter Control bit |
| (IbsOpCntCtl) set respectively (see AMD64 Architecture Programmer’s |
| Manual Volume 2: System Programming, 13.3 Instruction-Based |
| Sampling). Examples to use IBS: |
| |
| perf record -a -e cpu-cycles:p ... # use ibs op counting cycles |
| perf record -a -e r076:p ... # same as -e cpu-cycles:p |
| perf record -a -e r0C1:p ... # use ibs op counting micro-ops |
| |
| RAW HARDWARE EVENT DESCRIPTOR |
| ----------------------------- |
| Even when an event is not available in a symbolic form within perf right now, |
| it can be encoded in a per processor specific way. |
| |
| For instance For x86 CPUs NNN represents the raw register encoding with the |
| layout of IA32_PERFEVTSELx MSRs (see [Intel® 64 and IA-32 Architectures Software Developer's Manual Volume 3B: System Programming Guide] Figure 30-1 Layout |
| of IA32_PERFEVTSELx MSRs) or AMD's PerfEvtSeln (see [AMD64 Architecture Programmer’s Manual Volume 2: System Programming], Page 344, |
| Figure 13-7 Performance Event-Select Register (PerfEvtSeln)). |
| |
| Note: Only the following bit fields can be set in x86 counter |
| registers: event, umask, edge, inv, cmask. Esp. guest/host only and |
| OS/user mode flags must be setup using <<EVENT_MODIFIERS, EVENT |
| MODIFIERS>>. |
| |
| Example: |
| |
| If the Intel docs for a QM720 Core i7 describe an event as: |
| |
| Event Umask Event Mask |
| Num. Value Mnemonic Description Comment |
| |
| A8H 01H LSD.UOPS Counts the number of micro-ops Use cmask=1 and |
| delivered by loop stream detector invert to count |
| cycles |
| |
| raw encoding of 0x1A8 can be used: |
| |
| perf stat -e r1a8 -a sleep 1 |
| perf record -e r1a8 ... |
| |
| You should refer to the processor specific documentation for getting these |
| details. Some of them are referenced in the SEE ALSO section below. |
| |
| PARAMETERIZED EVENTS |
| -------------------- |
| |
| Some pmu events listed by 'perf-list' will be displayed with '?' in them. For |
| example: |
| |
| hv_gpci/dtbp_ptitc,phys_processor_idx=?/ |
| |
| This means that when provided as an event, a value for '?' must |
| also be supplied. For example: |
| |
| perf stat -C 0 -e 'hv_gpci/dtbp_ptitc,phys_processor_idx=0x2/' ... |
| |
| OPTIONS |
| ------- |
| |
| Without options all known events will be listed. |
| |
| To limit the list use: |
| |
| . 'hw' or 'hardware' to list hardware events such as cache-misses, etc. |
| |
| . 'sw' or 'software' to list software events such as context switches, etc. |
| |
| . 'cache' or 'hwcache' to list hardware cache events such as L1-dcache-loads, etc. |
| |
| . 'tracepoint' to list all tracepoint events, alternatively use |
| 'subsys_glob:event_glob' to filter by tracepoint subsystems such as sched, |
| block, etc. |
| |
| . 'pmu' to print the kernel supplied PMU events. |
| |
| . If none of the above is matched, it will apply the supplied glob to all |
| events, printing the ones that match. |
| |
| . As a last resort, it will do a substring search in all event names. |
| |
| One or more types can be used at the same time, listing the events for the |
| types specified. |
| |
| Support raw format: |
| |
| . '--raw-dump', shows the raw-dump of all the events. |
| . '--raw-dump [hw|sw|cache|tracepoint|pmu|event_glob]', shows the raw-dump of |
| a certain kind of events. |
| |
| SEE ALSO |
| -------- |
| linkperf:perf-stat[1], linkperf:perf-top[1], |
| linkperf:perf-record[1], |
| http://www.intel.com/Assets/PDF/manual/253669.pdf[Intel® 64 and IA-32 Architectures Software Developer's Manual Volume 3B: System Programming Guide], |
| http://support.amd.com/us/Processor_TechDocs/24593_APM_v2.pdf[AMD64 Architecture Programmer’s Manual Volume 2: System Programming] |
