| ============================================================================= |
| Freescale Frame Manager Device Bindings |
| |
| CONTENTS |
| - FMan Node |
| - FMan Port Node |
| - FMan MURAM Node |
| - FMan dTSEC/XGEC/mEMAC Node |
| - FMan IEEE 1588 Node |
| - FMan MDIO Node |
| - Example |
| |
| ============================================================================= |
| FMan Node |
| |
| DESCRIPTION |
| |
| Due to the fact that the FMan is an aggregation of sub-engines (ports, MACs, |
| etc.) the FMan node will have child nodes for each of them. |
| |
| PROPERTIES |
| |
| - compatible |
| Usage: required |
| Value type: <stringlist> |
| Definition: Must include "fsl,fman" |
| FMan version can be determined via FM_IP_REV_1 register in the |
| FMan block. The offset is 0xc4 from the beginning of the |
| Frame Processing Manager memory map (0xc3000 from the |
| beginning of the FMan node). |
| |
| - cell-index |
| Usage: required |
| Value type: <u32> |
| Definition: Specifies the index of the FMan unit. |
| |
| The cell-index value may be used by the SoC, to identify the |
| FMan unit in the SoC memory map. In the table bellow, |
| there's a description of the cell-index use in each SoC: |
| |
| - P1023: |
| register[bit] FMan unit cell-index |
| ============================================================ |
| DEVDISR[1] 1 0 |
| |
| - P2041, P3041, P4080 P5020, P5040: |
| register[bit] FMan unit cell-index |
| ============================================================ |
| DCFG_DEVDISR2[6] 1 0 |
| DCFG_DEVDISR2[14] 2 1 |
| (Second FM available only in P4080 and P5040) |
| |
| - B4860, T1040, T2080, T4240: |
| register[bit] FMan unit cell-index |
| ============================================================ |
| DCFG_CCSR_DEVDISR2[24] 1 0 |
| DCFG_CCSR_DEVDISR2[25] 2 1 |
| (Second FM available only in T4240) |
| |
| DEVDISR, DCFG_DEVDISR2 and DCFG_CCSR_DEVDISR2 are located in |
| the specific SoC "Device Configuration/Pin Control" Memory |
| Map. |
| |
| - reg |
| Usage: required |
| Value type: <prop-encoded-array> |
| Definition: A standard property. Specifies the offset of the |
| following configuration registers: |
| - BMI configuration registers. |
| - QMI configuration registers. |
| - DMA configuration registers. |
| - FPM configuration registers. |
| - FMan controller configuration registers. |
| |
| - ranges |
| Usage: required |
| Value type: <prop-encoded-array> |
| Definition: A standard property. |
| |
| - clocks |
| Usage: required |
| Value type: <prop-encoded-array> |
| Definition: phandle for the fman input clock. |
| |
| - clock-names |
| usage: required |
| Value type: <stringlist> |
| Definition: "fmanclk" for the fman input clock. |
| |
| - interrupts |
| Usage: required |
| Value type: <prop-encoded-array> |
| Definition: A pair of IRQs are specified in this property. |
| The first element is associated with the event interrupts and |
| the second element is associated with the error interrupts. |
| |
| - fsl,qman-channel-range |
| Usage: required |
| Value type: <prop-encoded-array> |
| Definition: Specifies the range of the available dedicated |
| channels in the FMan. The first cell specifies the beginning |
| of the range and the second cell specifies the number of |
| channels. |
| Further information available at: |
| "Work Queue (WQ) Channel Assignments in the QMan" section |
| in DPAA Reference Manual. |
| |
| - fsl,qman |
| - fsl,bman |
| Usage: required |
| Definition: See soc/fsl/qman.txt and soc/fsl/bman.txt |
| |
| ============================================================================= |
| FMan MURAM Node |
| |
| DESCRIPTION |
| |
| FMan Internal memory - shared between all the FMan modules. |
| It contains data structures that are common and written to or read by |
| the modules. |
| FMan internal memory is split into the following parts: |
| Packet buffering (Tx/Rx FIFOs) |
| Frames internal context |
| |
| PROPERTIES |
| |
| - compatible |
| Usage: required |
| Value type: <stringlist> |
| Definition: Must include "fsl,fman-muram" |
| |
| - ranges |
| Usage: required |
| Value type: <prop-encoded-array> |
| Definition: A standard property. |
| Specifies the multi-user memory offset and the size within |
| the FMan. |
| |
| EXAMPLE |
| |
| muram@0 { |
| compatible = "fsl,fman-muram"; |
| ranges = <0 0x000000 0x28000>; |
| }; |
| |
| ============================================================================= |
| FMan Port Node |
| |
| DESCRIPTION |
| |
| The Frame Manager (FMan) supports several types of hardware ports: |
| Ethernet receiver (RX) |
| Ethernet transmitter (TX) |
| Offline/Host command (O/H) |
| |
| PROPERTIES |
| |
| - compatible |
| Usage: required |
| Value type: <stringlist> |
| Definition: A standard property. |
| Must include one of the following: |
| - "fsl,fman-v2-port-oh" for FManV2 OH ports |
| - "fsl,fman-v2-port-rx" for FManV2 RX ports |
| - "fsl,fman-v2-port-tx" for FManV2 TX ports |
| - "fsl,fman-v3-port-oh" for FManV3 OH ports |
| - "fsl,fman-v3-port-rx" for FManV3 RX ports |
| - "fsl,fman-v3-port-tx" for FManV3 TX ports |
| |
| - cell-index |
| Usage: required |
| Value type: <u32> |
| Definition: Specifies the hardware port id. |
| Each hardware port on the FMan has its own hardware PortID. |
| Super set of all hardware Port IDs available at FMan Reference |
| Manual under "FMan Hardware Ports in Freescale Devices" table. |
| |
| Each hardware port is assigned a 4KB, port-specific page in |
| the FMan hardware port memory region (which is part of the |
| FMan memory map). The first 4 KB in the FMan hardware ports |
| memory region is used for what are called common registers. |
| The subsequent 63 4KB pages are allocated to the hardware |
| ports. |
| The page of a specific port is determined by the cell-index. |
| |
| - reg |
| Usage: required |
| Value type: <prop-encoded-array> |
| Definition: There is one reg region describing the port |
| configuration registers. |
| |
| - fsl,fman-10g-port |
| Usage: optional |
| Value type: boolean |
| Definition: The default port rate is 1G. |
| If this property exists, the port is s 10G port. |
| |
| - fsl,fman-best-effort-port |
| Usage: optional |
| Value type: boolean |
| Definition: Can be defined only if 10G-support is set. |
| This property marks a best-effort 10G port (10G port that |
| may not be capable of line rate). |
| |
| EXAMPLE |
| |
| port@a8000 { |
| cell-index = <0x28>; |
| compatible = "fsl,fman-v2-port-tx"; |
| reg = <0xa8000 0x1000>; |
| }; |
| |
| port@88000 { |
| cell-index = <0x8>; |
| compatible = "fsl,fman-v2-port-rx"; |
| reg = <0x88000 0x1000>; |
| }; |
| |
| port@81000 { |
| cell-index = <0x1>; |
| compatible = "fsl,fman-v2-port-oh"; |
| reg = <0x81000 0x1000>; |
| }; |
| |
| ============================================================================= |
| FMan dTSEC/XGEC/mEMAC Node |
| |
| DESCRIPTION |
| |
| mEMAC/dTSEC/XGEC are the Ethernet network interfaces |
| |
| PROPERTIES |
| |
| - compatible |
| Usage: required |
| Value type: <stringlist> |
| Definition: A standard property. |
| Must include one of the following: |
| - "fsl,fman-dtsec" for dTSEC MAC |
| - "fsl,fman-xgec" for XGEC MAC |
| - "fsl,fman-memac for mEMAC MAC |
| |
| - cell-index |
| Usage: required |
| Value type: <u32> |
| Definition: Specifies the MAC id. |
| |
| The cell-index value may be used by the FMan or the SoC, to |
| identify the MAC unit in the FMan (or SoC) memory map. |
| In the tables bellow there's a description of the cell-index |
| use, there are two tables, one describes the use of cell-index |
| by the FMan, the second describes the use by the SoC: |
| |
| 1. FMan Registers |
| |
| FManV2: |
| register[bit] MAC cell-index |
| ============================================================ |
| FM_EPI[16] XGEC 8 |
| FM_EPI[16+n] dTSECn n-1 |
| FM_NPI[11+n] dTSECn n-1 |
| n = 1,..,5 |
| |
| FManV3: |
| register[bit] MAC cell-index |
| ============================================================ |
| FM_EPI[16+n] mEMACn n-1 |
| FM_EPI[25] mEMAC10 9 |
| |
| FM_NPI[11+n] mEMACn n-1 |
| FM_NPI[10] mEMAC10 9 |
| FM_NPI[11] mEMAC9 8 |
| n = 1,..8 |
| |
| FM_EPI and FM_NPI are located in the FMan memory map. |
| |
| 2. SoC registers: |
| |
| - P2041, P3041, P4080 P5020, P5040: |
| register[bit] FMan MAC cell |
| Unit index |
| ============================================================ |
| DCFG_DEVDISR2[7] 1 XGEC 8 |
| DCFG_DEVDISR2[7+n] 1 dTSECn n-1 |
| DCFG_DEVDISR2[15] 2 XGEC 8 |
| DCFG_DEVDISR2[15+n] 2 dTSECn n-1 |
| n = 1,..5 |
| |
| - T1040, T2080, T4240, B4860: |
| register[bit] FMan MAC cell |
| Unit index |
| ============================================================ |
| DCFG_CCSR_DEVDISR2[n-1] 1 mEMACn n-1 |
| DCFG_CCSR_DEVDISR2[11+n] 2 mEMACn n-1 |
| n = 1,..6,9,10 |
| |
| EVDISR, DCFG_DEVDISR2 and DCFG_CCSR_DEVDISR2 are located in |
| the specific SoC "Device Configuration/Pin Control" Memory |
| Map. |
| |
| - reg |
| Usage: required |
| Value type: <prop-encoded-array> |
| Definition: A standard property. |
| |
| - fsl,fman-ports |
| Usage: required |
| Value type: <prop-encoded-array> |
| Definition: An array of two phandles - the first references is |
| the FMan RX port and the second is the TX port used by this |
| MAC. |
| |
| - ptp-timer |
| Usage required |
| Value type: <phandle> |
| Definition: A phandle for 1EEE1588 timer. |
| |
| EXAMPLE |
| |
| fman1_tx28: port@a8000 { |
| cell-index = <0x28>; |
| compatible = "fsl,fman-v2-port-tx"; |
| reg = <0xa8000 0x1000>; |
| }; |
| |
| fman1_rx8: port@88000 { |
| cell-index = <0x8>; |
| compatible = "fsl,fman-v2-port-rx"; |
| reg = <0x88000 0x1000>; |
| }; |
| |
| ptp-timer: ptp_timer@fe000 { |
| compatible = "fsl,fman-ptp-timer"; |
| reg = <0xfe000 0x1000>; |
| }; |
| |
| ethernet@e0000 { |
| compatible = "fsl,fman-dtsec"; |
| cell-index = <0>; |
| reg = <0xe0000 0x1000>; |
| fsl,fman-ports = <&fman1_rx8 &fman1_tx28>; |
| ptp-timer = <&ptp-timer>; |
| }; |
| |
| ============================================================================ |
| FMan IEEE 1588 Node |
| |
| DESCRIPTION |
| |
| The FMan interface to support IEEE 1588 |
| |
| |
| PROPERTIES |
| |
| - compatible |
| Usage: required |
| Value type: <stringlist> |
| Definition: A standard property. |
| Must include "fsl,fman-ptp-timer". |
| |
| - reg |
| Usage: required |
| Value type: <prop-encoded-array> |
| Definition: A standard property. |
| |
| EXAMPLE |
| |
| ptp-timer@fe000 { |
| compatible = "fsl,fman-ptp-timer"; |
| reg = <0xfe000 0x1000>; |
| }; |
| |
| ============================================================================= |
| FMan MDIO Node |
| |
| DESCRIPTION |
| |
| The MDIO is a bus to which the PHY devices are connected. |
| |
| PROPERTIES |
| |
| - compatible |
| Usage: required |
| Value type: <stringlist> |
| Definition: A standard property. |
| Must include "fsl,fman-mdio" for 1 Gb/s MDIO from FMan v2. |
| Must include "fsl,fman-xmdio" for 10 Gb/s MDIO from FMan v2. |
| Must include "fsl,fman-memac-mdio" for 1/10 Gb/s MDIO from |
| FMan v3. |
| |
| - reg |
| Usage: required |
| Value type: <prop-encoded-array> |
| Definition: A standard property. |
| |
| - bus-frequency |
| Usage: optional |
| Value type: <u32> |
| Definition: Specifies the external MDIO bus clock speed to |
| be used, if different from the standard 2.5 MHz. |
| This may be due to the standard speed being unsupported (e.g. |
| due to a hardware problem), or to advertise that all relevant |
| components in the system support a faster speed. |
| |
| - interrupts |
| Usage: required for external MDIO |
| Value type: <prop-encoded-array> |
| Definition: Event interrupt of external MDIO controller. |
| |
| - fsl,fman-internal-mdio |
| Usage: required for internal MDIO |
| Value type: boolean |
| Definition: Fman has internal MDIO for internal PCS(Physical |
| Coding Sublayer) PHYs and external MDIO for external PHYs. |
| The settings and programming routines for internal/external |
| MDIO are different. Must be included for internal MDIO. |
| |
| EXAMPLE |
| |
| Example for FMan v2 external MDIO: |
| |
| mdio@f1000 { |
| compatible = "fsl,fman-xmdio"; |
| reg = <0xf1000 0x1000>; |
| interrupts = <101 2 0 0>; |
| }; |
| |
| Example for FMan v3 internal MDIO: |
| |
| mdio@f1000 { |
| compatible = "fsl,fman-memac-mdio"; |
| reg = <0xf1000 0x1000>; |
| fsl,fman-internal-mdio; |
| }; |
| |
| ============================================================================= |
| Example |
| |
| fman@400000 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| cell-index = <1>; |
| compatible = "fsl,fman" |
| ranges = <0 0x400000 0x100000>; |
| reg = <0x400000 0x100000>; |
| clocks = <&fman_clk>; |
| clock-names = "fmanclk"; |
| interrupts = < |
| 96 2 0 0 |
| 16 2 1 1>; |
| fsl,qman-channel-range = <0x40 0xc>; |
| |
| muram@0 { |
| compatible = "fsl,fman-muram"; |
| reg = <0x0 0x28000>; |
| }; |
| |
| port@81000 { |
| cell-index = <1>; |
| compatible = "fsl,fman-v2-port-oh"; |
| reg = <0x81000 0x1000>; |
| }; |
| |
| port@82000 { |
| cell-index = <2>; |
| compatible = "fsl,fman-v2-port-oh"; |
| reg = <0x82000 0x1000>; |
| }; |
| |
| port@83000 { |
| cell-index = <3>; |
| compatible = "fsl,fman-v2-port-oh"; |
| reg = <0x83000 0x1000>; |
| }; |
| |
| port@84000 { |
| cell-index = <4>; |
| compatible = "fsl,fman-v2-port-oh"; |
| reg = <0x84000 0x1000>; |
| }; |
| |
| port@85000 { |
| cell-index = <5>; |
| compatible = "fsl,fman-v2-port-oh"; |
| reg = <0x85000 0x1000>; |
| }; |
| |
| port@86000 { |
| cell-index = <6>; |
| compatible = "fsl,fman-v2-port-oh"; |
| reg = <0x86000 0x1000>; |
| }; |
| |
| fman1_rx_0x8: port@88000 { |
| cell-index = <0x8>; |
| compatible = "fsl,fman-v2-port-rx"; |
| reg = <0x88000 0x1000>; |
| }; |
| |
| fman1_rx_0x9: port@89000 { |
| cell-index = <0x9>; |
| compatible = "fsl,fman-v2-port-rx"; |
| reg = <0x89000 0x1000>; |
| }; |
| |
| fman1_rx_0xa: port@8a000 { |
| cell-index = <0xa>; |
| compatible = "fsl,fman-v2-port-rx"; |
| reg = <0x8a000 0x1000>; |
| }; |
| |
| fman1_rx_0xb: port@8b000 { |
| cell-index = <0xb>; |
| compatible = "fsl,fman-v2-port-rx"; |
| reg = <0x8b000 0x1000>; |
| }; |
| |
| fman1_rx_0xc: port@8c000 { |
| cell-index = <0xc>; |
| compatible = "fsl,fman-v2-port-rx"; |
| reg = <0x8c000 0x1000>; |
| }; |
| |
| fman1_rx_0x10: port@90000 { |
| cell-index = <0x10>; |
| compatible = "fsl,fman-v2-port-rx"; |
| reg = <0x90000 0x1000>; |
| }; |
| |
| fman1_tx_0x28: port@a8000 { |
| cell-index = <0x28>; |
| compatible = "fsl,fman-v2-port-tx"; |
| reg = <0xa8000 0x1000>; |
| }; |
| |
| fman1_tx_0x29: port@a9000 { |
| cell-index = <0x29>; |
| compatible = "fsl,fman-v2-port-tx"; |
| reg = <0xa9000 0x1000>; |
| }; |
| |
| fman1_tx_0x2a: port@aa000 { |
| cell-index = <0x2a>; |
| compatible = "fsl,fman-v2-port-tx"; |
| reg = <0xaa000 0x1000>; |
| }; |
| |
| fman1_tx_0x2b: port@ab000 { |
| cell-index = <0x2b>; |
| compatible = "fsl,fman-v2-port-tx"; |
| reg = <0xab000 0x1000>; |
| }; |
| |
| fman1_tx_0x2c: port@ac0000 { |
| cell-index = <0x2c>; |
| compatible = "fsl,fman-v2-port-tx"; |
| reg = <0xac000 0x1000>; |
| }; |
| |
| fman1_tx_0x30: port@b0000 { |
| cell-index = <0x30>; |
| compatible = "fsl,fman-v2-port-tx"; |
| reg = <0xb0000 0x1000>; |
| }; |
| |
| ethernet@e0000 { |
| compatible = "fsl,fman-dtsec"; |
| cell-index = <0>; |
| reg = <0xe0000 0x1000>; |
| fsl,fman-ports = <&fman1_rx_0x8 &fman1_tx_0x28>; |
| }; |
| |
| ethernet@e2000 { |
| compatible = "fsl,fman-dtsec"; |
| cell-index = <1>; |
| reg = <0xe2000 0x1000>; |
| fsl,fman-ports = <&fman1_rx_0x9 &fman1_tx_0x29>; |
| }; |
| |
| ethernet@e4000 { |
| compatible = "fsl,fman-dtsec"; |
| cell-index = <2>; |
| reg = <0xe4000 0x1000>; |
| fsl,fman-ports = <&fman1_rx_0xa &fman1_tx_0x2a>; |
| }; |
| |
| ethernet@e6000 { |
| compatible = "fsl,fman-dtsec"; |
| cell-index = <3>; |
| reg = <0xe6000 0x1000>; |
| fsl,fman-ports = <&fman1_rx_0xb &fman1_tx_0x2b>; |
| }; |
| |
| ethernet@e8000 { |
| compatible = "fsl,fman-dtsec"; |
| cell-index = <4>; |
| reg = <0xf0000 0x1000>; |
| fsl,fman-ports = <&fman1_rx_0xc &fman1_tx_0x2c>; |
| |
| ethernet@f0000 { |
| cell-index = <8>; |
| compatible = "fsl,fman-xgec"; |
| reg = <0xf0000 0x1000>; |
| fsl,fman-ports = <&fman1_rx_0x10 &fman1_tx_0x30>; |
| }; |
| |
| ptp-timer@fe000 { |
| compatible = "fsl,fman-ptp-timer"; |
| reg = <0xfe000 0x1000>; |
| }; |
| |
| mdio@f1000 { |
| compatible = "fsl,fman-xmdio"; |
| reg = <0xf1000 0x1000>; |
| interrupts = <101 2 0 0>; |
| }; |
| }; |
