arch/x86/entry/entry_64_compat.S - kernel/bruno - Git at Google

 /*
  * Compatibility mode system call entry point for x86-64.
  *
  * Copyright 2000-2002 Andi Kleen, SuSE Labs.
  */
 #include "calling.h"
 #include <asm/asm-offsets.h>
 #include <asm/current.h>
 #include <asm/errno.h>
 #include <asm/ia32_unistd.h>
 #include <asm/thread_info.h>
 #include <asm/segment.h>
 #include <asm/irqflags.h>
 #include <asm/asm.h>
 #include <asm/smap.h>
 #include <linux/linkage.h>
 #include <linux/err.h>

 	.section .entry.text, "ax"

 #ifdef CONFIG_PARAVIRT
 ENTRY(native_usergs_sysret32)
 	swapgs
 	sysretl
 ENDPROC(native_usergs_sysret32)
 #endif

 /*
  * 32-bit SYSENTER instruction entry.
  *
  * SYSENTER loads ss, rsp, cs, and rip from previously programmed MSRs.
  * IF and VM in rflags are cleared (IOW: interrupts are off).
  * SYSENTER does not save anything on the stack,
  * and does not save old rip (!!!) and rflags.
  *
  * Arguments:
  * eax  system call number
  * ebx  arg1
  * ecx  arg2
  * edx  arg3
  * esi  arg4
  * edi  arg5
  * ebp  user stack
  * 0(%ebp) arg6
  *
  * This is purely a fast path. For anything complicated we use the int 0x80
  * path below. We set up a complete hardware stack frame to share code
  * with the int 0x80 path.
  */
 ENTRY(entry_SYSENTER_compat)
 	/* Interrupts are off on entry. */
 	SWAPGS_UNSAFE_STACK
 	movq	PER_CPU_VAR(cpu_current_top_of_stack), %rsp

 	/*
 	 * User tracing code (ptrace or signal handlers) might assume that
 	 * the saved RAX contains a 32-bit number when we're invoking a 32-bit
 	 * syscall.  Just in case the high bits are nonzero, zero-extend
 	 * the syscall number.  (This could almost certainly be deleted
 	 * with no ill effects.)
 	 */
 	movl	%eax, %eax

 	/* Construct struct pt_regs on stack */
 	pushq	$__USER32_DS		/* pt_regs->ss */
 	pushq	%rbp			/* pt_regs->sp (stashed in bp) */

 	/*
 	 * Push flags.  This is nasty.  First, interrupts are currently
 	 * off, but we need pt_regs->flags to have IF set.  Second, even
 	 * if TF was set when SYSENTER started, it's clear by now.  We fix
 	 * that later using TIF_SINGLESTEP.
 	 */
 	pushfq				/* pt_regs->flags (except IF = 0) */
 	orl	$X86_EFLAGS_IF, (%rsp)	/* Fix saved flags */
 	ASM_CLAC			/* Clear AC after saving FLAGS */

 	pushq	$__USER32_CS		/* pt_regs->cs */
 	xorq    %r8,%r8
 	pushq	%r8			/* pt_regs->ip = 0 (placeholder) */
 	pushq	%rax			/* pt_regs->orig_ax */
 	pushq	%rdi			/* pt_regs->di */
 	pushq	%rsi			/* pt_regs->si */
 	pushq	%rdx			/* pt_regs->dx */
 	pushq	%rcx			/* pt_regs->cx */
 	pushq	$-ENOSYS		/* pt_regs->ax */
 	pushq   %r8                     /* pt_regs->r8  = 0 */
 	pushq   %r8                     /* pt_regs->r9  = 0 */
 	pushq   %r8                     /* pt_regs->r10 = 0 */
 	pushq   %r8                     /* pt_regs->r11 = 0 */
 	pushq   %rbx                    /* pt_regs->rbx */
 	pushq   %rbp                    /* pt_regs->rbp (will be overwritten) */
 	pushq   %r8                     /* pt_regs->r12 = 0 */
 	pushq   %r8                     /* pt_regs->r13 = 0 */
 	pushq   %r8                     /* pt_regs->r14 = 0 */
 	pushq   %r8                     /* pt_regs->r15 = 0 */
 	cld

 	/*
 	 * Sysenter doesn't filter flags, so we need to clear NT
 	 * ourselves.  To save a few cycles, we can check whether
 	 * NT was set instead of doing an unconditional popfq.
 	 * This needs to happen before enabling interrupts so that
 	 * we don't get preempted with NT set.
 	 *
 	 * NB.: sysenter_fix_flags is a label with the code under it moved
 	 * out-of-line as an optimization: NT is unlikely to be set in the
 	 * majority of the cases and instead of polluting the I$ unnecessarily,
 	 * we're keeping that code behind a branch which will predict as
 	 * not-taken and therefore its instructions won't be fetched.
 	 */
 	testl	$X86_EFLAGS_NT, EFLAGS(%rsp)
 	jnz	sysenter_fix_flags
 sysenter_flags_fixed:

 	/*
 	 * User mode is traced as though IRQs are on, and SYSENTER
 	 * turned them off.
 	 */
 	TRACE_IRQS_OFF

 	movq	%rsp, %rdi
 	call	do_fast_syscall_32
 	/* XEN PV guests always use IRET path */
 	ALTERNATIVE "testl %eax, %eax; jz .Lsyscall_32_done", \
 		    "jmp .Lsyscall_32_done", X86_FEATURE_XENPV
 	jmp	sysret32_from_system_call

 sysenter_fix_flags:
 	pushq	$X86_EFLAGS_FIXED
 	popfq
 	jmp	sysenter_flags_fixed
 ENDPROC(entry_SYSENTER_compat)

 /*
  * 32-bit SYSCALL instruction entry.
  *
  * 32-bit SYSCALL saves rip to rcx, clears rflags.RF, then saves rflags to r11,
  * then loads new ss, cs, and rip from previously programmed MSRs.
  * rflags gets masked by a value from another MSR (so CLD and CLAC
  * are not needed). SYSCALL does not save anything on the stack
  * and does not change rsp.
  *
  * Note: rflags saving+masking-with-MSR happens only in Long mode
  * (in legacy 32-bit mode, IF, RF and VM bits are cleared and that's it).
  * Don't get confused: rflags saving+masking depends on Long Mode Active bit
  * (EFER.LMA=1), NOT on bitness of userspace where SYSCALL executes
  * or target CS descriptor's L bit (SYSCALL does not read segment descriptors).
  *
  * Arguments:
  * eax  system call number
  * ecx  return address
  * ebx  arg1
  * ebp  arg2	(note: not saved in the stack frame, should not be touched)
  * edx  arg3
  * esi  arg4
  * edi  arg5
  * esp  user stack
  * 0(%esp) arg6
  */
 ENTRY(entry_SYSCALL_compat)
 	/* Interrupts are off on entry. */
 	SWAPGS_UNSAFE_STACK

 	/* Stash user ESP and switch to the kernel stack. */
 	movl	%esp, %r8d
 	movq	PER_CPU_VAR(cpu_current_top_of_stack), %rsp

 	/* Zero-extending 32-bit regs, do not remove */
 	movl	%eax, %eax

 	/* Construct struct pt_regs on stack */
 	pushq	$__USER32_DS		/* pt_regs->ss */
 	pushq	%r8			/* pt_regs->sp */
 	pushq	%r11			/* pt_regs->flags */
 	pushq	$__USER32_CS		/* pt_regs->cs */
 	pushq	%rcx			/* pt_regs->ip */
 	pushq	%rax			/* pt_regs->orig_ax */
 	pushq	%rdi			/* pt_regs->di */
 	pushq	%rsi			/* pt_regs->si */
 	pushq	%rdx			/* pt_regs->dx */
 	pushq	%rbp			/* pt_regs->cx (stashed in bp) */
 	pushq	$-ENOSYS		/* pt_regs->ax */
 	xorq    %r8,%r8
 	pushq   %r8                     /* pt_regs->r8  = 0 */
 	pushq   %r8                     /* pt_regs->r9  = 0 */
 	pushq   %r8                     /* pt_regs->r10 = 0 */
 	pushq   %r8                     /* pt_regs->r11 = 0 */
 	pushq   %rbx                    /* pt_regs->rbx */
 	pushq   %rbp                    /* pt_regs->rbp (will be overwritten) */
 	pushq   %r8                     /* pt_regs->r12 = 0 */
 	pushq   %r8                     /* pt_regs->r13 = 0 */
 	pushq   %r8                     /* pt_regs->r14 = 0 */
 	pushq   %r8                     /* pt_regs->r15 = 0 */

 	/*
 	 * User mode is traced as though IRQs are on, and SYSENTER
 	 * turned them off.
 	 */
 	TRACE_IRQS_OFF

 	movq	%rsp, %rdi
 	call	do_fast_syscall_32
 	/* XEN PV guests always use IRET path */
 	ALTERNATIVE "testl %eax, %eax; jz .Lsyscall_32_done", \
 		    "jmp .Lsyscall_32_done", X86_FEATURE_XENPV

 	/* Opportunistic SYSRET */
 sysret32_from_system_call:
 	TRACE_IRQS_ON			/* User mode traces as IRQs on. */
 	movq	RBX(%rsp), %rbx		/* pt_regs->rbx */
 	movq	RBP(%rsp), %rbp		/* pt_regs->rbp */
 	movq	EFLAGS(%rsp), %r11	/* pt_regs->flags (in r11) */
 	movq	RIP(%rsp), %rcx		/* pt_regs->ip (in rcx) */
 	addq	$RAX, %rsp		/* Skip r8-r15 */
 	popq	%rax			/* pt_regs->rax */
 	popq	%rdx			/* Skip pt_regs->cx */
 	popq	%rdx			/* pt_regs->dx */
 	popq	%rsi			/* pt_regs->si */
 	popq	%rdi			/* pt_regs->di */

         /*
          * USERGS_SYSRET32 does:
          *  GSBASE = user's GS base
          *  EIP = ECX
          *  RFLAGS = R11
          *  CS = __USER32_CS
          *  SS = __USER_DS
          *
 	 * ECX will not match pt_regs->cx, but we're returning to a vDSO
 	 * trampoline that will fix up RCX, so this is okay.
 	 *
 	 * R12-R15 are callee-saved, so they contain whatever was in them
 	 * when the system call started, which is already known to user
 	 * code.  We zero R8-R10 to avoid info leaks.
          */
 	xorq	%r8, %r8
 	xorq	%r9, %r9
 	xorq	%r10, %r10
 	movq	RSP-ORIG_RAX(%rsp), %rsp
         USERGS_SYSRET32
 END(entry_SYSCALL_compat)

 /*
  * Emulated IA32 system calls via int 0x80.
  *
  * Arguments:
  * eax  system call number
  * ebx  arg1
  * ecx  arg2
  * edx  arg3
  * esi  arg4
  * edi  arg5
  * ebp  arg6	(note: not saved in the stack frame, should not be touched)
  *
  * Notes:
  * Uses the same stack frame as the x86-64 version.
  * All registers except eax must be saved (but ptrace may violate that).
  * Arguments are zero extended. For system calls that want sign extension and
  * take long arguments a wrapper is needed. Most calls can just be called
  * directly.
  * Assumes it is only called from user space and entered with interrupts off.
  */

 ENTRY(entry_INT80_compat)
 	/*
 	 * Interrupts are off on entry.
 	 */
 	PARAVIRT_ADJUST_EXCEPTION_FRAME
 	ASM_CLAC			/* Do this early to minimize exposure */
 	SWAPGS

 	/*
 	 * User tracing code (ptrace or signal handlers) might assume that
 	 * the saved RAX contains a 32-bit number when we're invoking a 32-bit
 	 * syscall.  Just in case the high bits are nonzero, zero-extend
 	 * the syscall number.  (This could almost certainly be deleted
 	 * with no ill effects.)
 	 */
 	movl	%eax, %eax

 	/* Construct struct pt_regs on stack (iret frame is already on stack) */
 	pushq	%rax			/* pt_regs->orig_ax */
 	pushq	%rdi			/* pt_regs->di */
 	pushq	%rsi			/* pt_regs->si */
 	pushq	%rdx			/* pt_regs->dx */
 	pushq	%rcx			/* pt_regs->cx */
 	pushq	$-ENOSYS		/* pt_regs->ax */
 	xorq    %r8,%r8
 	pushq   %r8                     /* pt_regs->r8  = 0 */
 	pushq   %r8                     /* pt_regs->r9  = 0 */
 	pushq   %r8                     /* pt_regs->r10 = 0 */
 	pushq   %r8                     /* pt_regs->r11 = 0 */
 	pushq   %rbx                    /* pt_regs->rbx */
 	pushq   %rbp                    /* pt_regs->rbp */
 	pushq   %r12                    /* pt_regs->r12 */
 	pushq   %r13                    /* pt_regs->r13 */
 	pushq   %r14                    /* pt_regs->r14 */
 	pushq   %r15                    /* pt_regs->r15 */
 	cld

 	/*
 	 * User mode is traced as though IRQs are on, and the interrupt
 	 * gate turned them off.
 	 */
 	TRACE_IRQS_OFF

 	movq	%rsp, %rdi
 	call	do_syscall_32_irqs_off
 .Lsyscall_32_done:

 	/* Go back to user mode. */
 	TRACE_IRQS_ON
 	SWAPGS
 	jmp	restore_regs_and_iret
 END(entry_INT80_compat)

 	ALIGN
 GLOBAL(stub32_clone)
 	/*
 	 * The 32-bit clone ABI is: clone(..., int tls_val, int *child_tidptr).
 	 * The 64-bit clone ABI is: clone(..., int *child_tidptr, int tls_val).
 	 *
 	 * The native 64-bit kernel's sys_clone() implements the latter,
 	 * so we need to swap arguments here before calling it:
 	 */
 	xchg	%r8, %rcx
 	jmp	sys_clone
	/*
	* Compatibility mode system call entry point for x86-64.
	*
	* Copyright 2000-2002 Andi Kleen, SuSE Labs.
	*/
	#include "calling.h"
	#include <asm/asm-offsets.h>
	#include <asm/current.h>
	#include <asm/errno.h>
	#include <asm/ia32_unistd.h>
	#include <asm/thread_info.h>
	#include <asm/segment.h>
	#include <asm/irqflags.h>
	#include <asm/asm.h>
	#include <asm/smap.h>
	#include <linux/linkage.h>
	#include <linux/err.h>

	.section .entry.text, "ax"

	#ifdef CONFIG_PARAVIRT
	ENTRY(native_usergs_sysret32)
	swapgs
	sysretl
	ENDPROC(native_usergs_sysret32)
	#endif

	/*
	* 32-bit SYSENTER instruction entry.
	*
	* SYSENTER loads ss, rsp, cs, and rip from previously programmed MSRs.
	* IF and VM in rflags are cleared (IOW: interrupts are off).
	* SYSENTER does not save anything on the stack,
	* and does not save old rip (!!!) and rflags.
	*
	* Arguments:
	* eax system call number
	* ebx arg1
	* ecx arg2
	* edx arg3
	* esi arg4
	* edi arg5
	* ebp user stack
	* 0(%ebp) arg6
	*
	* This is purely a fast path. For anything complicated we use the int 0x80
	* path below. We set up a complete hardware stack frame to share code
	* with the int 0x80 path.
	*/
	ENTRY(entry_SYSENTER_compat)
	/* Interrupts are off on entry. */
	SWAPGS_UNSAFE_STACK
	movq PER_CPU_VAR(cpu_current_top_of_stack), %rsp

	/*
	* User tracing code (ptrace or signal handlers) might assume that
	* the saved RAX contains a 32-bit number when we're invoking a 32-bit
	* syscall. Just in case the high bits are nonzero, zero-extend
	* the syscall number. (This could almost certainly be deleted
	* with no ill effects.)
	*/
	movl %eax, %eax

	/* Construct struct pt_regs on stack */
	pushq $__USER32_DS /* pt_regs->ss */
	pushq %rbp /* pt_regs->sp (stashed in bp) */

	/*
	* Push flags. This is nasty. First, interrupts are currently
	* off, but we need pt_regs->flags to have IF set. Second, even
	* if TF was set when SYSENTER started, it's clear by now. We fix
	* that later using TIF_SINGLESTEP.
	*/
	pushfq /* pt_regs->flags (except IF = 0) */
	orl $X86_EFLAGS_IF, (%rsp) /* Fix saved flags */
	ASM_CLAC /* Clear AC after saving FLAGS */

	pushq $__USER32_CS /* pt_regs->cs */
	xorq %r8,%r8
	pushq %r8 /* pt_regs->ip = 0 (placeholder) */
	pushq %rax /* pt_regs->orig_ax */
	pushq %rdi /* pt_regs->di */
	pushq %rsi /* pt_regs->si */
	pushq %rdx /* pt_regs->dx */
	pushq %rcx /* pt_regs->cx */
	pushq $-ENOSYS /* pt_regs->ax */
	pushq %r8 /* pt_regs->r8 = 0 */
	pushq %r8 /* pt_regs->r9 = 0 */
	pushq %r8 /* pt_regs->r10 = 0 */
	pushq %r8 /* pt_regs->r11 = 0 */
	pushq %rbx /* pt_regs->rbx */
	pushq %rbp /* pt_regs->rbp (will be overwritten) */
	pushq %r8 /* pt_regs->r12 = 0 */
	pushq %r8 /* pt_regs->r13 = 0 */
	pushq %r8 /* pt_regs->r14 = 0 */
	pushq %r8 /* pt_regs->r15 = 0 */
	cld

	/*
	* Sysenter doesn't filter flags, so we need to clear NT
	* ourselves. To save a few cycles, we can check whether
	* NT was set instead of doing an unconditional popfq.
	* This needs to happen before enabling interrupts so that
	* we don't get preempted with NT set.
	*
	* NB.: sysenter_fix_flags is a label with the code under it moved
	* out-of-line as an optimization: NT is unlikely to be set in the
	* majority of the cases and instead of polluting the I$ unnecessarily,
	* we're keeping that code behind a branch which will predict as
	* not-taken and therefore its instructions won't be fetched.
	*/
	testl $X86_EFLAGS_NT, EFLAGS(%rsp)
	jnz sysenter_fix_flags
	sysenter_flags_fixed:

	/*
	* User mode is traced as though IRQs are on, and SYSENTER
	* turned them off.
	*/
	TRACE_IRQS_OFF

	movq %rsp, %rdi
	call do_fast_syscall_32
	/* XEN PV guests always use IRET path */
	ALTERNATIVE "testl %eax, %eax; jz .Lsyscall_32_done", \
	"jmp .Lsyscall_32_done", X86_FEATURE_XENPV
	jmp sysret32_from_system_call

	sysenter_fix_flags:
	pushq $X86_EFLAGS_FIXED
	popfq
	jmp sysenter_flags_fixed
	ENDPROC(entry_SYSENTER_compat)

	/*
	* 32-bit SYSCALL instruction entry.
	*
	* 32-bit SYSCALL saves rip to rcx, clears rflags.RF, then saves rflags to r11,
	* then loads new ss, cs, and rip from previously programmed MSRs.
	* rflags gets masked by a value from another MSR (so CLD and CLAC
	* are not needed). SYSCALL does not save anything on the stack
	* and does not change rsp.
	*
	* Note: rflags saving+masking-with-MSR happens only in Long mode
	* (in legacy 32-bit mode, IF, RF and VM bits are cleared and that's it).
	* Don't get confused: rflags saving+masking depends on Long Mode Active bit
	* (EFER.LMA=1), NOT on bitness of userspace where SYSCALL executes
	* or target CS descriptor's L bit (SYSCALL does not read segment descriptors).
	*
	* Arguments:
	* eax system call number
	* ecx return address
	* ebx arg1
	* ebp arg2 (note: not saved in the stack frame, should not be touched)
	* edx arg3
	* esi arg4
	* edi arg5
	* esp user stack
	* 0(%esp) arg6
	*/
	ENTRY(entry_SYSCALL_compat)
	/* Interrupts are off on entry. */
	SWAPGS_UNSAFE_STACK

	/* Stash user ESP and switch to the kernel stack. */
	movl %esp, %r8d
	movq PER_CPU_VAR(cpu_current_top_of_stack), %rsp

	/* Zero-extending 32-bit regs, do not remove */
	movl %eax, %eax

	/* Construct struct pt_regs on stack */
	pushq $__USER32_DS /* pt_regs->ss */
	pushq %r8 /* pt_regs->sp */
	pushq %r11 /* pt_regs->flags */
	pushq $__USER32_CS /* pt_regs->cs */
	pushq %rcx /* pt_regs->ip */
	pushq %rax /* pt_regs->orig_ax */
	pushq %rdi /* pt_regs->di */
	pushq %rsi /* pt_regs->si */
	pushq %rdx /* pt_regs->dx */
	pushq %rbp /* pt_regs->cx (stashed in bp) */
	pushq $-ENOSYS /* pt_regs->ax */
	xorq %r8,%r8
	pushq %r8 /* pt_regs->r8 = 0 */
	pushq %r8 /* pt_regs->r9 = 0 */
	pushq %r8 /* pt_regs->r10 = 0 */
	pushq %r8 /* pt_regs->r11 = 0 */
	pushq %rbx /* pt_regs->rbx */
	pushq %rbp /* pt_regs->rbp (will be overwritten) */
	pushq %r8 /* pt_regs->r12 = 0 */
	pushq %r8 /* pt_regs->r13 = 0 */
	pushq %r8 /* pt_regs->r14 = 0 */
	pushq %r8 /* pt_regs->r15 = 0 */

	/*
	* User mode is traced as though IRQs are on, and SYSENTER
	* turned them off.
	*/
	TRACE_IRQS_OFF

	movq %rsp, %rdi
	call do_fast_syscall_32
	/* XEN PV guests always use IRET path */
	ALTERNATIVE "testl %eax, %eax; jz .Lsyscall_32_done", \
	"jmp .Lsyscall_32_done", X86_FEATURE_XENPV

	/* Opportunistic SYSRET */
	sysret32_from_system_call:
	TRACE_IRQS_ON /* User mode traces as IRQs on. */
	movq RBX(%rsp), %rbx /* pt_regs->rbx */
	movq RBP(%rsp), %rbp /* pt_regs->rbp */
	movq EFLAGS(%rsp), %r11 /* pt_regs->flags (in r11) */
	movq RIP(%rsp), %rcx /* pt_regs->ip (in rcx) */
	addq $RAX, %rsp /* Skip r8-r15 */
	popq %rax /* pt_regs->rax */
	popq %rdx /* Skip pt_regs->cx */
	popq %rdx /* pt_regs->dx */
	popq %rsi /* pt_regs->si */
	popq %rdi /* pt_regs->di */

	/*
	* USERGS_SYSRET32 does:
	* GSBASE = user's GS base
	* EIP = ECX
	* RFLAGS = R11
	* CS = __USER32_CS
	* SS = __USER_DS
	*
	* ECX will not match pt_regs->cx, but we're returning to a vDSO
	* trampoline that will fix up RCX, so this is okay.
	*
	* R12-R15 are callee-saved, so they contain whatever was in them
	* when the system call started, which is already known to user
	* code. We zero R8-R10 to avoid info leaks.
	*/
	xorq %r8, %r8
	xorq %r9, %r9
	xorq %r10, %r10
	movq RSP-ORIG_RAX(%rsp), %rsp
	USERGS_SYSRET32
	END(entry_SYSCALL_compat)

	/*
	* Emulated IA32 system calls via int 0x80.
	*
	* Arguments:
	* eax system call number
	* ebx arg1
	* ecx arg2
	* edx arg3
	* esi arg4
	* edi arg5
	* ebp arg6 (note: not saved in the stack frame, should not be touched)
	*
	* Notes:
	* Uses the same stack frame as the x86-64 version.
	* All registers except eax must be saved (but ptrace may violate that).
	* Arguments are zero extended. For system calls that want sign extension and
	* take long arguments a wrapper is needed. Most calls can just be called
	* directly.
	* Assumes it is only called from user space and entered with interrupts off.
	*/

	ENTRY(entry_INT80_compat)
	/*
	* Interrupts are off on entry.
	*/
	PARAVIRT_ADJUST_EXCEPTION_FRAME
	ASM_CLAC /* Do this early to minimize exposure */
	SWAPGS

	/*
	* User tracing code (ptrace or signal handlers) might assume that
	* the saved RAX contains a 32-bit number when we're invoking a 32-bit
	* syscall. Just in case the high bits are nonzero, zero-extend
	* the syscall number. (This could almost certainly be deleted
	* with no ill effects.)
	*/
	movl %eax, %eax

	/* Construct struct pt_regs on stack (iret frame is already on stack) */
	pushq %rax /* pt_regs->orig_ax */
	pushq %rdi /* pt_regs->di */
	pushq %rsi /* pt_regs->si */
	pushq %rdx /* pt_regs->dx */
	pushq %rcx /* pt_regs->cx */
	pushq $-ENOSYS /* pt_regs->ax */
	xorq %r8,%r8
	pushq %r8 /* pt_regs->r8 = 0 */
	pushq %r8 /* pt_regs->r9 = 0 */
	pushq %r8 /* pt_regs->r10 = 0 */
	pushq %r8 /* pt_regs->r11 = 0 */
	pushq %rbx /* pt_regs->rbx */
	pushq %rbp /* pt_regs->rbp */
	pushq %r12 /* pt_regs->r12 */
	pushq %r13 /* pt_regs->r13 */
	pushq %r14 /* pt_regs->r14 */
	pushq %r15 /* pt_regs->r15 */
	cld

	/*
	* User mode is traced as though IRQs are on, and the interrupt
	* gate turned them off.
	*/
	TRACE_IRQS_OFF

	movq %rsp, %rdi
	call do_syscall_32_irqs_off
	.Lsyscall_32_done:

	/* Go back to user mode. */
	TRACE_IRQS_ON
	SWAPGS
	jmp restore_regs_and_iret
	END(entry_INT80_compat)

	ALIGN
	GLOBAL(stub32_clone)
	/*
	* The 32-bit clone ABI is: clone(..., int tls_val, int *child_tidptr).
	* The 64-bit clone ABI is: clone(..., int *child_tidptr, int tls_val).
	*
	* The native 64-bit kernel's sys_clone() implements the latter,
	* so we need to swap arguments here before calling it:
	*/
	xchg %r8, %rcx
	jmp sys_clone