drivers/net/bnx2x/bnx2x_link.h - kernel/bruno - Git at Google

 /* Copyright 2008-2010 Broadcom Corporation
  *
  * Unless you and Broadcom execute a separate written software license
  * agreement governing use of this software, this software is licensed to you
  * under the terms of the GNU General Public License version 2, available
  * at http://www.gnu.org/licenses/old-licenses/gpl-2.0.html (the "GPL").
  *
  * Notwithstanding the above, under no circumstances may you combine this
  * software in any way with any other Broadcom software provided under a
  * license other than the GPL, without Broadcom's express prior written
  * consent.
  *
  * Written by Yaniv Rosner
  *
  */

 #ifndef BNX2X_LINK_H
 #define BNX2X_LINK_H


 /***********************************************************/
 /*                         Defines                         */
 /***********************************************************/
 #define DEFAULT_PHY_DEV_ADDR	3
 #define E2_DEFAULT_PHY_DEV_ADDR	5


 #define BNX2X_FLOW_CTRL_AUTO		PORT_FEATURE_FLOW_CONTROL_AUTO
 #define BNX2X_FLOW_CTRL_TX		PORT_FEATURE_FLOW_CONTROL_TX
 #define BNX2X_FLOW_CTRL_RX		PORT_FEATURE_FLOW_CONTROL_RX
 #define BNX2X_FLOW_CTRL_BOTH		PORT_FEATURE_FLOW_CONTROL_BOTH
 #define BNX2X_FLOW_CTRL_NONE		PORT_FEATURE_FLOW_CONTROL_NONE

 #define SPEED_AUTO_NEG	    0
 #define SPEED_12000		12000
 #define SPEED_12500		12500
 #define SPEED_13000		13000
 #define SPEED_15000		15000
 #define SPEED_16000		16000

 #define SFP_EEPROM_VENDOR_NAME_ADDR		0x14
 #define SFP_EEPROM_VENDOR_NAME_SIZE		16
 #define SFP_EEPROM_VENDOR_OUI_ADDR		0x25
 #define SFP_EEPROM_VENDOR_OUI_SIZE		3
 #define SFP_EEPROM_PART_NO_ADDR 		0x28
 #define SFP_EEPROM_PART_NO_SIZE		16
 #define PWR_FLT_ERR_MSG_LEN			250

 #define XGXS_EXT_PHY_TYPE(ext_phy_config) \
 		((ext_phy_config) & PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK)
 #define XGXS_EXT_PHY_ADDR(ext_phy_config) \
 		(((ext_phy_config) & PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >> \
 		 PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT)
 #define SERDES_EXT_PHY_TYPE(ext_phy_config) \
 		((ext_phy_config) & PORT_HW_CFG_SERDES_EXT_PHY_TYPE_MASK)

 /* Single Media Direct board is the plain 577xx board with CX4/RJ45 jacks */
 #define SINGLE_MEDIA_DIRECT(params)	(params->num_phys == 1)
 /* Single Media board contains single external phy */
 #define SINGLE_MEDIA(params)		(params->num_phys == 2)
 /* Dual Media board contains two external phy with different media */
 #define DUAL_MEDIA(params)		(params->num_phys == 3)
 #define FW_PARAM_MDIO_CTRL_OFFSET 16
 #define FW_PARAM_SET(phy_addr, phy_type, mdio_access) \
 	(phy_addr | phy_type | mdio_access << FW_PARAM_MDIO_CTRL_OFFSET)
 /***********************************************************/
 /*                         Structs                         */
 /***********************************************************/
 #define INT_PHY		0
 #define EXT_PHY1	1
 #define EXT_PHY2	2
 #define MAX_PHYS	3

 /* Same configuration is shared between the XGXS and the first external phy */
 #define LINK_CONFIG_SIZE (MAX_PHYS - 1)
 #define LINK_CONFIG_IDX(_phy_idx) ((_phy_idx == INT_PHY) ? \
 					 0 : (_phy_idx - 1))
 /***********************************************************/
 /*                      bnx2x_phy struct                     */
 /*  Defines the required arguments and function per phy    */
 /***********************************************************/
 struct link_vars;
 struct link_params;
 struct bnx2x_phy;

 typedef u8 (*config_init_t)(struct bnx2x_phy *phy, struct link_params *params,
 			    struct link_vars *vars);
 typedef u8 (*read_status_t)(struct bnx2x_phy *phy, struct link_params *params,
 			    struct link_vars *vars);
 typedef void (*link_reset_t)(struct bnx2x_phy *phy,
 			     struct link_params *params);
 typedef void (*config_loopback_t)(struct bnx2x_phy *phy,
 				  struct link_params *params);
 typedef u8 (*format_fw_ver_t)(u32 raw, u8 *str, u16 *len);
 typedef void (*hw_reset_t)(struct bnx2x_phy *phy, struct link_params *params);
 typedef void (*set_link_led_t)(struct bnx2x_phy *phy,
 			       struct link_params *params, u8 mode);
 typedef void (*phy_specific_func_t)(struct bnx2x_phy *phy,
 				    struct link_params *params, u32 action);

 struct bnx2x_phy {
 	u32 type;

 	/* Loaded during init */
 	u8 addr;

 	u8 flags;
 	/* Require HW lock */
 #define FLAGS_HW_LOCK_REQUIRED		(1<<0)
 	/* No Over-Current detection */
 #define FLAGS_NOC			(1<<1)
 	/* Fan failure detection required */
 #define FLAGS_FAN_FAILURE_DET_REQ	(1<<2)
 	/* Initialize first the XGXS and only then the phy itself */
 #define FLAGS_INIT_XGXS_FIRST		(1<<3)
 #define FLAGS_REARM_LATCH_SIGNAL	(1<<6)
 #define FLAGS_SFP_NOT_APPROVED		(1<<7)

 	u8 def_md_devad;
 	u8 reserved;
 	/* preemphasis values for the rx side */
 	u16 rx_preemphasis[4];

 	/* preemphasis values for the tx side */
 	u16 tx_preemphasis[4];

 	/* EMAC address for access MDIO */
 	u32 mdio_ctrl;

 	u32 supported;

 	u32 media_type;
 #define	ETH_PHY_UNSPECIFIED 0x0
 #define	ETH_PHY_SFP_FIBER   0x1
 #define	ETH_PHY_XFP_FIBER   0x2
 #define	ETH_PHY_DA_TWINAX   0x3
 #define	ETH_PHY_BASE_T      0x4
 #define	ETH_PHY_NOT_PRESENT 0xff

 	/* The address in which version is located*/
 	u32 ver_addr;

 	u16 req_flow_ctrl;

 	u16 req_line_speed;

 	u32 speed_cap_mask;

 	u16 req_duplex;
 	u16 rsrv;
 	/* Called per phy/port init, and it configures LASI, speed, autoneg,
 	 duplex, flow control negotiation, etc. */
 	config_init_t config_init;

 	/* Called due to interrupt. It determines the link, speed */
 	read_status_t read_status;

 	/* Called when driver is unloading. Should reset the phy */
 	link_reset_t link_reset;

 	/* Set the loopback configuration for the phy */
 	config_loopback_t config_loopback;

 	/* Format the given raw number into str up to len */
 	format_fw_ver_t format_fw_ver;

 	/* Reset the phy (both ports) */
 	hw_reset_t hw_reset;

 	/* Set link led mode (on/off/oper)*/
 	set_link_led_t set_link_led;

 	/* PHY Specific tasks */
 	phy_specific_func_t phy_specific_func;
 #define DISABLE_TX	1
 #define ENABLE_TX	2
 };

 /* Inputs parameters to the CLC */
 struct link_params {

 	u8 port;

 	/* Default / User Configuration */
 	u8 loopback_mode;
 #define LOOPBACK_NONE	0
 #define LOOPBACK_EMAC	1
 #define LOOPBACK_BMAC	2
 #define LOOPBACK_XGXS		3
 #define LOOPBACK_EXT_PHY	4
 #define LOOPBACK_EXT 	5

 	/* Device parameters */
 	u8 mac_addr[6];

 	u16 req_duplex[LINK_CONFIG_SIZE];
 	u16 req_flow_ctrl[LINK_CONFIG_SIZE];

 	u16 req_line_speed[LINK_CONFIG_SIZE]; /* Also determine AutoNeg */

 	/* shmem parameters */
 	u32 shmem_base;
 	u32 shmem2_base;
 	u32 speed_cap_mask[LINK_CONFIG_SIZE];
 	u32 switch_cfg;
 #define SWITCH_CFG_1G		PORT_FEATURE_CON_SWITCH_1G_SWITCH
 #define SWITCH_CFG_10G		PORT_FEATURE_CON_SWITCH_10G_SWITCH
 #define SWITCH_CFG_AUTO_DETECT	PORT_FEATURE_CON_SWITCH_AUTO_DETECT

 	u32 lane_config;

 	/* Phy register parameter */
 	u32 chip_id;

 	u32 feature_config_flags;
 #define FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED (1<<0)
 #define FEATURE_CONFIG_BC_SUPPORTS_OPT_MDL_VRFY	(1<<2)
 #define FEATURE_CONFIG_BC_SUPPORTS_DUAL_PHY_OPT_MDL_VRFY	(1<<3)
 	/* Will be populated during common init */
 	struct bnx2x_phy phy[MAX_PHYS];

 	/* Will be populated during common init */
 	u8 num_phys;

 	u8 rsrv;
 	u16 hw_led_mode; /* part of the hw_config read from the shmem */
 	u32 multi_phy_config;

 	/* Device pointer passed to all callback functions */
 	struct bnx2x *bp;
 	u16 req_fc_auto_adv; /* Should be set to TX / BOTH when
 				req_flow_ctrl is set to AUTO */
 };

 /* Output parameters */
 struct link_vars {
 	u8 phy_flags;

 	u8 mac_type;
 #define MAC_TYPE_NONE		0
 #define MAC_TYPE_EMAC		1
 #define MAC_TYPE_BMAC		2

 	u8 phy_link_up; /* internal phy link indication */
 	u8 link_up;

 	u16 line_speed;
 	u16 duplex;

 	u16 flow_ctrl;
 	u16 ieee_fc;

 	/* The same definitions as the shmem parameter */
 	u32 link_status;
 };

 /***********************************************************/
 /*                         Functions                       */
 /***********************************************************/
 u8 bnx2x_phy_init(struct link_params *input, struct link_vars *output);

 /* Reset the link. Should be called when driver or interface goes down
    Before calling phy firmware upgrade, the reset_ext_phy should be set
    to 0 */
 u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars,
 		  u8 reset_ext_phy);

 /* bnx2x_link_update should be called upon link interrupt */
 u8 bnx2x_link_update(struct link_params *input, struct link_vars *output);

 /* use the following phy functions to read/write from external_phy
   In order to use it to read/write internal phy registers, use
   DEFAULT_PHY_DEV_ADDR as devad, and (_bank + (_addr & 0xf)) as
   the register */
 u8 bnx2x_phy_read(struct link_params *params, u8 phy_addr,
 		  u8 devad, u16 reg, u16 *ret_val);

 u8 bnx2x_phy_write(struct link_params *params, u8 phy_addr,
 		   u8 devad, u16 reg, u16 val);
 /* Reads the link_status from the shmem,
    and update the link vars accordingly */
 void bnx2x_link_status_update(struct link_params *input,
 			    struct link_vars *output);
 /* returns string representing the fw_version of the external phy */
 u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded,
 			      u8 *version, u16 len);

 /* Set/Unset the led
    Basically, the CLC takes care of the led for the link, but in case one needs
    to set/unset the led unnaturally, set the "mode" to LED_MODE_OPER to
    blink the led, and LED_MODE_OFF to set the led off.*/
 u8 bnx2x_set_led(struct link_params *params, struct link_vars *vars,
 		 u8 mode, u32 speed);
 #define LED_MODE_OFF			0
 #define LED_MODE_ON			1
 #define LED_MODE_OPER			2
 #define LED_MODE_FRONT_PANEL_OFF	3

 /* bnx2x_handle_module_detect_int should be called upon module detection
    interrupt */
 void bnx2x_handle_module_detect_int(struct link_params *params);

 /* Get the actual link status. In case it returns 0, link is up,
 	otherwise link is down*/
 u8 bnx2x_test_link(struct link_params *input, struct link_vars *vars,
 		   u8 is_serdes);

 /* One-time initialization for external phy after power up */
 u8 bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base_path[],
 			 u32 shmem2_base_path[], u32 chip_id);

 /* Reset the external PHY using GPIO */
 void bnx2x_ext_phy_hw_reset(struct bnx2x *bp, u8 port);

 /* Reset the external of SFX7101 */
 void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, struct bnx2x_phy *phy);

 void bnx2x_hw_reset_phy(struct link_params *params);

 /* Checks if HW lock is required for this phy/board type */
 u8 bnx2x_hw_lock_required(struct bnx2x *bp, u32 shmem_base,
 			  u32 shmem2_base);

 /* Check swap bit and adjust PHY order */
 u32 bnx2x_phy_selection(struct link_params *params);

 /* Probe the phys on board, and populate them in "params" */
 u8 bnx2x_phy_probe(struct link_params *params);
 /* Checks if fan failure detection is required on one of the phys on board */
 u8 bnx2x_fan_failure_det_req(struct bnx2x *bp, u32 shmem_base,
 			     u32 shmem2_base, u8 port);

 #endif /* BNX2X_LINK_H */
	/* Copyright 2008-2010 Broadcom Corporation
	*
	* Unless you and Broadcom execute a separate written software license
	* agreement governing use of this software, this software is licensed to you
	* under the terms of the GNU General Public License version 2, available
	* at http://www.gnu.org/licenses/old-licenses/gpl-2.0.html (the "GPL").
	*
	* Notwithstanding the above, under no circumstances may you combine this
	* software in any way with any other Broadcom software provided under a
	* license other than the GPL, without Broadcom's express prior written
	* consent.
	*
	* Written by Yaniv Rosner
	*
	*/

	#ifndef BNX2X_LINK_H
	#define BNX2X_LINK_H



	/***********************************************************/
	/* Defines */
	/***********************************************************/
	#define DEFAULT_PHY_DEV_ADDR 3
	#define E2_DEFAULT_PHY_DEV_ADDR 5



	#define BNX2X_FLOW_CTRL_AUTO PORT_FEATURE_FLOW_CONTROL_AUTO
	#define BNX2X_FLOW_CTRL_TX PORT_FEATURE_FLOW_CONTROL_TX
	#define BNX2X_FLOW_CTRL_RX PORT_FEATURE_FLOW_CONTROL_RX
	#define BNX2X_FLOW_CTRL_BOTH PORT_FEATURE_FLOW_CONTROL_BOTH
	#define BNX2X_FLOW_CTRL_NONE PORT_FEATURE_FLOW_CONTROL_NONE

	#define SPEED_AUTO_NEG 0
	#define SPEED_12000 12000
	#define SPEED_12500 12500
	#define SPEED_13000 13000
	#define SPEED_15000 15000
	#define SPEED_16000 16000

	#define SFP_EEPROM_VENDOR_NAME_ADDR 0x14
	#define SFP_EEPROM_VENDOR_NAME_SIZE 16
	#define SFP_EEPROM_VENDOR_OUI_ADDR 0x25
	#define SFP_EEPROM_VENDOR_OUI_SIZE 3
	#define SFP_EEPROM_PART_NO_ADDR 0x28
	#define SFP_EEPROM_PART_NO_SIZE 16
	#define PWR_FLT_ERR_MSG_LEN 250

	#define XGXS_EXT_PHY_TYPE(ext_phy_config) \
	((ext_phy_config) & PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK)
	#define XGXS_EXT_PHY_ADDR(ext_phy_config) \
	(((ext_phy_config) & PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >> \
	PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT)
	#define SERDES_EXT_PHY_TYPE(ext_phy_config) \
	((ext_phy_config) & PORT_HW_CFG_SERDES_EXT_PHY_TYPE_MASK)

	/* Single Media Direct board is the plain 577xx board with CX4/RJ45 jacks */
	#define SINGLE_MEDIA_DIRECT(params) (params->num_phys == 1)
	/* Single Media board contains single external phy */
	#define SINGLE_MEDIA(params) (params->num_phys == 2)
	/* Dual Media board contains two external phy with different media */
	#define DUAL_MEDIA(params) (params->num_phys == 3)
	#define FW_PARAM_MDIO_CTRL_OFFSET 16
	#define FW_PARAM_SET(phy_addr, phy_type, mdio_access) \
	(phy_addr \| phy_type \| mdio_access << FW_PARAM_MDIO_CTRL_OFFSET)
	/***********************************************************/
	/* Structs */
	/***********************************************************/
	#define INT_PHY 0
	#define EXT_PHY1 1
	#define EXT_PHY2 2
	#define MAX_PHYS 3

	/* Same configuration is shared between the XGXS and the first external phy */
	#define LINK_CONFIG_SIZE (MAX_PHYS - 1)
	#define LINK_CONFIG_IDX(_phy_idx) ((_phy_idx == INT_PHY) ? \
	0 : (_phy_idx - 1))
	/***********************************************************/
	/* bnx2x_phy struct */
	/* Defines the required arguments and function per phy */
	/***********************************************************/
	struct link_vars;
	struct link_params;
	struct bnx2x_phy;

	typedef u8 (config_init_t)(struct bnx2x_phy phy, struct link_params *params,
	struct link_vars *vars);
	typedef u8 (read_status_t)(struct bnx2x_phy phy, struct link_params *params,
	struct link_vars *vars);
	typedef void (link_reset_t)(struct bnx2x_phy phy,
	struct link_params *params);
	typedef void (config_loopback_t)(struct bnx2x_phy phy,
	struct link_params *params);
	typedef u8 (format_fw_ver_t)(u32 raw, u8 str, u16 *len);
	typedef void (hw_reset_t)(struct bnx2x_phy phy, struct link_params *params);
	typedef void (set_link_led_t)(struct bnx2x_phy phy,
	struct link_params *params, u8 mode);
	typedef void (phy_specific_func_t)(struct bnx2x_phy phy,
	struct link_params *params, u32 action);

	struct bnx2x_phy {
	u32 type;

	/* Loaded during init */
	u8 addr;

	u8 flags;
	/* Require HW lock */
	#define FLAGS_HW_LOCK_REQUIRED (1<<0)
	/* No Over-Current detection */
	#define FLAGS_NOC (1<<1)
	/* Fan failure detection required */
	#define FLAGS_FAN_FAILURE_DET_REQ (1<<2)
	/* Initialize first the XGXS and only then the phy itself */
	#define FLAGS_INIT_XGXS_FIRST (1<<3)
	#define FLAGS_REARM_LATCH_SIGNAL (1<<6)
	#define FLAGS_SFP_NOT_APPROVED (1<<7)

	u8 def_md_devad;
	u8 reserved;
	/* preemphasis values for the rx side */
	u16 rx_preemphasis[4];

	/* preemphasis values for the tx side */
	u16 tx_preemphasis[4];

	/* EMAC address for access MDIO */
	u32 mdio_ctrl;

	u32 supported;

	u32 media_type;
	#define ETH_PHY_UNSPECIFIED 0x0
	#define ETH_PHY_SFP_FIBER 0x1
	#define ETH_PHY_XFP_FIBER 0x2
	#define ETH_PHY_DA_TWINAX 0x3
	#define ETH_PHY_BASE_T 0x4
	#define ETH_PHY_NOT_PRESENT 0xff

	/* The address in which version is located*/
	u32 ver_addr;

	u16 req_flow_ctrl;

	u16 req_line_speed;

	u32 speed_cap_mask;

	u16 req_duplex;
	u16 rsrv;
	/* Called per phy/port init, and it configures LASI, speed, autoneg,
	duplex, flow control negotiation, etc. */
	config_init_t config_init;

	/* Called due to interrupt. It determines the link, speed */
	read_status_t read_status;

	/* Called when driver is unloading. Should reset the phy */
	link_reset_t link_reset;

	/* Set the loopback configuration for the phy */
	config_loopback_t config_loopback;

	/* Format the given raw number into str up to len */
	format_fw_ver_t format_fw_ver;

	/* Reset the phy (both ports) */
	hw_reset_t hw_reset;

	/* Set link led mode (on/off/oper)*/
	set_link_led_t set_link_led;

	/* PHY Specific tasks */
	phy_specific_func_t phy_specific_func;
	#define DISABLE_TX 1
	#define ENABLE_TX 2
	};

	/* Inputs parameters to the CLC */
	struct link_params {

	u8 port;

	/* Default / User Configuration */
	u8 loopback_mode;
	#define LOOPBACK_NONE 0
	#define LOOPBACK_EMAC 1
	#define LOOPBACK_BMAC 2
	#define LOOPBACK_XGXS 3
	#define LOOPBACK_EXT_PHY 4
	#define LOOPBACK_EXT 5

	/* Device parameters */
	u8 mac_addr[6];

	u16 req_duplex[LINK_CONFIG_SIZE];
	u16 req_flow_ctrl[LINK_CONFIG_SIZE];

	u16 req_line_speed[LINK_CONFIG_SIZE]; /* Also determine AutoNeg */

	/* shmem parameters */
	u32 shmem_base;
	u32 shmem2_base;
	u32 speed_cap_mask[LINK_CONFIG_SIZE];
	u32 switch_cfg;
	#define SWITCH_CFG_1G PORT_FEATURE_CON_SWITCH_1G_SWITCH
	#define SWITCH_CFG_10G PORT_FEATURE_CON_SWITCH_10G_SWITCH
	#define SWITCH_CFG_AUTO_DETECT PORT_FEATURE_CON_SWITCH_AUTO_DETECT

	u32 lane_config;

	/* Phy register parameter */
	u32 chip_id;

	u32 feature_config_flags;
	#define FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED (1<<0)
	#define FEATURE_CONFIG_BC_SUPPORTS_OPT_MDL_VRFY (1<<2)
	#define FEATURE_CONFIG_BC_SUPPORTS_DUAL_PHY_OPT_MDL_VRFY (1<<3)
	/* Will be populated during common init */
	struct bnx2x_phy phy[MAX_PHYS];

	/* Will be populated during common init */
	u8 num_phys;

	u8 rsrv;
	u16 hw_led_mode; /* part of the hw_config read from the shmem */
	u32 multi_phy_config;

	/* Device pointer passed to all callback functions */
	struct bnx2x *bp;
	u16 req_fc_auto_adv; /* Should be set to TX / BOTH when
	req_flow_ctrl is set to AUTO */
	};

	/* Output parameters */
	struct link_vars {
	u8 phy_flags;

	u8 mac_type;
	#define MAC_TYPE_NONE 0
	#define MAC_TYPE_EMAC 1
	#define MAC_TYPE_BMAC 2

	u8 phy_link_up; /* internal phy link indication */
	u8 link_up;

	u16 line_speed;
	u16 duplex;

	u16 flow_ctrl;
	u16 ieee_fc;

	/* The same definitions as the shmem parameter */
	u32 link_status;
	};

	/***********************************************************/
	/* Functions */
	/***********************************************************/
	u8 bnx2x_phy_init(struct link_params input, struct link_vars output);

	/* Reset the link. Should be called when driver or interface goes down
	Before calling phy firmware upgrade, the reset_ext_phy should be set
	to 0 */
	u8 bnx2x_link_reset(struct link_params params, struct link_vars vars,
	u8 reset_ext_phy);

	/* bnx2x_link_update should be called upon link interrupt */
	u8 bnx2x_link_update(struct link_params input, struct link_vars output);

	/* use the following phy functions to read/write from external_phy
	In order to use it to read/write internal phy registers, use
	DEFAULT_PHY_DEV_ADDR as devad, and (_bank + (_addr & 0xf)) as
	the register */
	u8 bnx2x_phy_read(struct link_params *params, u8 phy_addr,
	u8 devad, u16 reg, u16 *ret_val);

	u8 bnx2x_phy_write(struct link_params *params, u8 phy_addr,
	u8 devad, u16 reg, u16 val);
	/* Reads the link_status from the shmem,
	and update the link vars accordingly */
	void bnx2x_link_status_update(struct link_params *input,
	struct link_vars *output);
	/* returns string representing the fw_version of the external phy */
	u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded,
	u8 *version, u16 len);

	/* Set/Unset the led
	Basically, the CLC takes care of the led for the link, but in case one needs
	to set/unset the led unnaturally, set the "mode" to LED_MODE_OPER to
	blink the led, and LED_MODE_OFF to set the led off.*/
	u8 bnx2x_set_led(struct link_params params, struct link_vars vars,
	u8 mode, u32 speed);
	#define LED_MODE_OFF 0
	#define LED_MODE_ON 1
	#define LED_MODE_OPER 2
	#define LED_MODE_FRONT_PANEL_OFF 3

	/* bnx2x_handle_module_detect_int should be called upon module detection
	interrupt */
	void bnx2x_handle_module_detect_int(struct link_params *params);

	/* Get the actual link status. In case it returns 0, link is up,
	otherwise link is down*/
	u8 bnx2x_test_link(struct link_params input, struct link_vars vars,
	u8 is_serdes);

	/* One-time initialization for external phy after power up */
	u8 bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base_path[],
	u32 shmem2_base_path[], u32 chip_id);

	/* Reset the external PHY using GPIO */
	void bnx2x_ext_phy_hw_reset(struct bnx2x *bp, u8 port);

	/* Reset the external of SFX7101 */
	void bnx2x_sfx7101_sp_sw_reset(struct bnx2x bp, struct bnx2x_phy phy);

	void bnx2x_hw_reset_phy(struct link_params *params);

	/* Checks if HW lock is required for this phy/board type */
	u8 bnx2x_hw_lock_required(struct bnx2x *bp, u32 shmem_base,
	u32 shmem2_base);

	/* Check swap bit and adjust PHY order */
	u32 bnx2x_phy_selection(struct link_params *params);

	/* Probe the phys on board, and populate them in "params" */
	u8 bnx2x_phy_probe(struct link_params *params);
	/* Checks if fan failure detection is required on one of the phys on board */
	u8 bnx2x_fan_failure_det_req(struct bnx2x *bp, u32 shmem_base,
	u32 shmem2_base, u8 port);

	#endif /* BNX2X_LINK_H */