fs/skeleton/bin/ledmonitor.platform_gfiberwc

#!/bin/sh
#
# This script monitors CONTROL_PATH folder and decides which is the
# led sequence that has to be echoed to the LEDS_FILE.

. /etc/utils.sh

# Output file.
BASE_PATH="/tmp/gpio"
LEDS_FILE="$BASE_PATH/leds"
CONTROL_PATH="$BASE_PATH/ledcontrol"

LEDSTATE_FILE="$BASE_PATH/ledstate"
IP_FILE="$BASE_PATH/ipconnected"
LINK_DOWN_FILE="$BASE_PATH/link_down"
ACS_FILE="$CONTROL_PATH/acsconnected"
OVERTEMP_FILE="$CONTROL_PATH/overtemperature"
WAITPOWER_FILE="$CONTROL_PATH/waitpower"

# Hardware verion set by manufacture process.
# HW_REV/HW_VER is 0/0 or non 0/1, gpio 15 should be ignored.
# HW_REV/HW_VER is 0/1, gpio 15 is used to control dim/bright.
HW_REV=$(sysvar_cmd --get HW_REV 2>/dev/null)
HW_VER=$(sysvar_cmd --get HW_VER 2>/dev/null)

# Bit sequences.
ALL_LEDS_OFF="0"
HW_FAIL_LED_ON="1" # solid red
ACS_LED_ON="2" # solid blue
IP_LED_ON="2 0 2 0 2 0" # fast blue
LINK_DOWN_LED_ON="1 0 " # slow red blink
ANYTHING_ELSE="x2 2 0" # slow blink blue

change_state() {
  # Check if the new state is different from the previous one
  if [ ! -e "$LEDSTATE_FILE" ] || [ "$last_ledstate" != "$1" ]; then
    if [ "x$HW_REV" = "x0" ] && [ "x$HW_VER" = "x1" ]; then
      if [ "x$1" = "xACSCONTACT" ]; then
        diags set_led_dim on
      else
        diags set_led_dim off
      fi
    fi
    leds $2
    last_leds="$2"
    atomic $LEDSTATE_FILE "$1"
    last_ledstate="$1"
    echo "state changed to: $last_ledstate $last_leds"
  fi
}

does_interface_exist() {
  [ -e "/sys/class/net/$1" ]
}

has_ip_address() {
  [ -n "$(ip -f inet6 addr show dev $1 scope global)" ] ||
    [ -n "$(ip -f inet addr show dev $1 scope global)" ]
}

is_link_up() {
  # If there is an explicit WAN link, use that.
  # Otherwise for TV Boxes, check MoCA and Ethernet
  # and for Storage Boxes check only Ethernet
  if does_interface_exist wan0; then
    is-interface-up wan0
    return $?
  fi
  is-interface-up eth1
}

watch-dir $CONTROL_PATH |
while read f; do

  if is_link_up; then
    test ! -e "$LINK_DOWN_FILE" || rm -f "$LINK_DOWN_FILE"
    success=
    if does_interface_exist wan0; then
      ifs="wan0 wan0.2"
    else
      ifs="br0"
    fi
    for ifname in $ifs; do
      if has_ip_address $ifname; then
        success="IP address acquired on $ifname"
        break
      fi
    done
    if [ -n "$success" ]; then
      echo "$success" >"$IP_FILE"
    else
      rm -f "$ACS_FILE" "$IP_FILE"
    fi
  else
    echo "Link down" >"$LINK_DOWN_FILE"
    rm -f "$ACS_FILE" "$IP_FILE"
  fi

  if [ -f "$OVERTEMP_FILE" ]; then
    change_state OVERTEMP "$HW_FAIL_LED_ON"
  elif [ -f "$WAITPOWER_FILE" ]; then
    change_state POWEROFF "$ALL_LEDS_OFF"
  elif [ -f "$LINK_DOWN_FILE" ]; then
    change_state LINKDOWN "$LINK_DOWN_LED_ON"
  elif [ ! -f "$IP_FILE" ]; then
    change_state NOIP "$ANYTHING_ELSE"                  # progress: link but no ip
  elif [ ! -f "$ACS_FILE" ]; then
    change_state IPV6ACQUIRED "$IP_LED_ON"              # progress: ip but no acs
  else
    change_state ACSCONTACT "$ACS_LED_ON"               # success!
  fi
done