| #include <common.h> |
| #include <errno.h> |
| #include <clock.h> |
| #include <linux/mtd/mtd.h> |
| #include <linux/mtd/nand.h> |
| #include <linux/err.h> |
| #include <linux/mtd/nand_ecc.h> |
| #include <asm/byteorder.h> |
| #include <asm/io.h> |
| #include <malloc.h> |
| #include <module.h> |
| |
| #include "nand.h" |
| |
| static int nand_do_write_oob(struct mtd_info *mtd, loff_t to, |
| struct mtd_oob_ops *ops); |
| |
| /** |
| * nand_write_buf - [DEFAULT] write buffer to chip |
| * @mtd: MTD device structure |
| * @buf: data buffer |
| * @len: number of bytes to write |
| * |
| * Default write function for 8bit buswith |
| */ |
| void nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) |
| { |
| int i; |
| struct nand_chip *chip = mtd->priv; |
| |
| for (i = 0; i < len; i++) |
| writeb(buf[i], chip->IO_ADDR_W); |
| } |
| |
| /** |
| * nand_write_buf16 - [DEFAULT] write buffer to chip |
| * @mtd: MTD device structure |
| * @buf: data buffer |
| * @len: number of bytes to write |
| * |
| * Default write function for 16bit buswith |
| */ |
| void nand_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len) |
| { |
| int i; |
| struct nand_chip *chip = mtd->priv; |
| u16 *p = (u16 *) buf; |
| len >>= 1; |
| |
| for (i = 0; i < len; i++) |
| writew(p[i], chip->IO_ADDR_W); |
| |
| } |
| |
| /** |
| * nand_default_block_markbad - [DEFAULT] mark a block bad |
| * @mtd: MTD device structure |
| * @ofs: offset from device start |
| * |
| * This is the default implementation, which can be overridden by |
| * a hardware specific driver. |
| */ |
| int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs) |
| { |
| struct nand_chip *chip = mtd->priv; |
| uint8_t buf[2] = { 0, 0 }; |
| int block, ret; |
| |
| /* Get block number */ |
| block = (int)(ofs >> chip->bbt_erase_shift); |
| if (chip->bbt) |
| chip->bbt[block >> 2] |= 0x01 << ((block & 0x03) << 1); |
| |
| /* Do we have a flash based bad block table ? */ |
| #ifdef CONFIG_NAND_BBT |
| if (chip->options & NAND_USE_FLASH_BBT) |
| ret = nand_update_bbt(mtd, ofs); |
| else |
| #endif |
| { |
| /* We write two bytes, so we dont have to mess with 16 bit |
| * access |
| */ |
| ofs += mtd->oobsize; |
| chip->ops.len = chip->ops.ooblen = 2; |
| chip->ops.datbuf = NULL; |
| chip->ops.oobbuf = buf; |
| chip->ops.ooboffs = chip->badblockpos & ~0x01; |
| |
| ret = nand_do_write_oob(mtd, ofs, &chip->ops); |
| } |
| if (!ret) |
| mtd->ecc_stats.badblocks++; |
| |
| return ret; |
| } |
| |
| /** |
| * nand_check_wp - [GENERIC] check if the chip is write protected |
| * @mtd: MTD device structure |
| * Check, if the device is write protected |
| * |
| * The function expects, that the device is already selected |
| */ |
| static int nand_check_wp(struct mtd_info *mtd) |
| { |
| struct nand_chip *chip = mtd->priv; |
| /* Check the WP bit */ |
| chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); |
| return (chip->read_byte(mtd) & NAND_STATUS_WP) ? 0 : 1; |
| } |
| |
| /** |
| * nand_write_oob_std - [REPLACABLE] the most common OOB data write function |
| * @mtd: mtd info structure |
| * @chip: nand chip info structure |
| * @page: page number to write |
| */ |
| int nand_write_oob_std(struct mtd_info *mtd, struct nand_chip *chip, |
| int page) |
| { |
| int status = 0; |
| const uint8_t *buf = chip->oob_poi; |
| int length = mtd->oobsize; |
| |
| chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page); |
| chip->write_buf(mtd, buf, length); |
| /* Send command to program the OOB data */ |
| chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); |
| |
| status = chip->waitfunc(mtd, chip); |
| |
| return status & NAND_STATUS_FAIL ? -EIO : 0; |
| } |
| |
| /** |
| * nand_write_page_raw - [Intern] raw page write function |
| * @mtd: mtd info structure |
| * @chip: nand chip info structure |
| * @buf: data buffer |
| */ |
| void nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, |
| const uint8_t *buf) |
| { |
| chip->write_buf(mtd, buf, mtd->writesize); |
| chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); |
| } |
| |
| /** |
| * nand_write_page - [REPLACEABLE] write one page |
| * @mtd: MTD device structure |
| * @chip: NAND chip descriptor |
| * @buf: the data to write |
| * @page: page number to write |
| * @cached: cached programming |
| * @raw: use _raw version of write_page |
| */ |
| int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip, |
| const uint8_t *buf, int page, int cached, int raw) |
| { |
| int status; |
| |
| chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page); |
| |
| if (unlikely(raw)) |
| chip->ecc.write_page_raw(mtd, chip, buf); |
| else |
| chip->ecc.write_page(mtd, chip, buf); |
| |
| /* |
| * Cached progamming disabled for now, Not sure if its worth the |
| * trouble. The speed gain is not very impressive. (2.3->2.6Mib/s) |
| */ |
| cached = 0; |
| |
| if (!cached || !(chip->options & NAND_CACHEPRG)) { |
| |
| chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); |
| status = chip->waitfunc(mtd, chip); |
| /* |
| * See if operation failed and additional status checks are |
| * available |
| */ |
| if ((status & NAND_STATUS_FAIL) && (chip->errstat)) |
| status = chip->errstat(mtd, chip, FL_WRITING, status, |
| page); |
| |
| if (status & NAND_STATUS_FAIL) { |
| return -EIO; |
| } |
| } else { |
| chip->cmdfunc(mtd, NAND_CMD_CACHEDPROG, -1, -1); |
| status = chip->waitfunc(mtd, chip); |
| } |
| |
| #ifdef CONFIG_MTD_NAND_VERIFY_WRITE |
| /* Send command to read back the data */ |
| chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); |
| |
| if (chip->verify_buf(mtd, buf, mtd->writesize)) |
| return -EIO; |
| #endif |
| return 0; |
| } |
| |
| /** |
| * nand_fill_oob - [Internal] Transfer client buffer to oob |
| * @chip: nand chip structure |
| * @oob: oob data buffer |
| * @ops: oob ops structure |
| */ |
| static uint8_t *nand_fill_oob(struct nand_chip *chip, uint8_t *oob, |
| struct mtd_oob_ops *ops) |
| { |
| size_t len = ops->ooblen; |
| |
| switch(ops->mode) { |
| |
| case MTD_OOB_PLACE: |
| case MTD_OOB_RAW: |
| memcpy(chip->oob_poi + ops->ooboffs, oob, len); |
| return oob + len; |
| |
| case MTD_OOB_AUTO: { |
| struct nand_oobfree *free = chip->ecc.layout->oobfree; |
| uint32_t boffs = 0, woffs = ops->ooboffs; |
| size_t bytes = 0; |
| |
| for(; free->length && len; free++, len -= bytes) { |
| /* Write request not from offset 0 ? */ |
| if (unlikely(woffs)) { |
| if (woffs >= free->length) { |
| woffs -= free->length; |
| continue; |
| } |
| boffs = free->offset + woffs; |
| bytes = min_t(size_t, len, |
| (free->length - woffs)); |
| woffs = 0; |
| } else { |
| bytes = min_t(size_t, len, free->length); |
| boffs = free->offset; |
| } |
| memcpy(chip->oob_poi + boffs, oob, bytes); |
| oob += bytes; |
| } |
| return oob; |
| } |
| default: |
| BUG(); |
| } |
| return NULL; |
| } |
| |
| #define NOTALIGNED(x) (x & (chip->subpagesize - 1)) != 0 |
| |
| /** |
| * nand_do_write_ops - [Internal] NAND write with ECC |
| * @mtd: MTD device structure |
| * @to: offset to write to |
| * @ops: oob operations description structure |
| * |
| * NAND write with ECC |
| */ |
| int nand_do_write_ops(struct mtd_info *mtd, loff_t to, |
| struct mtd_oob_ops *ops) |
| { |
| int chipnr, realpage, page, blockmask, column; |
| struct nand_chip *chip = mtd->priv; |
| uint32_t writelen = ops->len; |
| uint8_t *oob = ops->oobbuf; |
| uint8_t *buf = ops->datbuf; |
| int ret, subpage; |
| |
| ops->retlen = 0; |
| if (!writelen) |
| return 0; |
| |
| /* reject writes, which are not page aligned */ |
| if (NOTALIGNED(to) || NOTALIGNED(ops->len)) { |
| printk(KERN_NOTICE "nand_write: " |
| "Attempt to write not page aligned data\n"); |
| return -EINVAL; |
| } |
| |
| column = to & (mtd->writesize - 1); |
| subpage = column || (writelen & (mtd->writesize - 1)); |
| |
| if (subpage && oob) |
| return -EINVAL; |
| |
| chipnr = (int)(to >> chip->chip_shift); |
| chip->select_chip(mtd, chipnr); |
| |
| /* Check, if it is write protected */ |
| if (nand_check_wp(mtd)) { |
| return -EIO; |
| } |
| |
| realpage = (int)(to >> chip->page_shift); |
| page = realpage & chip->pagemask; |
| blockmask = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1; |
| |
| /* Invalidate the page cache, when we write to the cached page */ |
| if (to <= (chip->pagebuf << chip->page_shift) && |
| (chip->pagebuf << chip->page_shift) < (to + ops->len)) |
| chip->pagebuf = -1; |
| |
| /* Initialize to all 0xFF, to avoid the possibility of |
| left over OOB data from a previous OOB read. */ |
| memset(chip->oob_poi, 0xff, mtd->oobsize); |
| |
| while(1) { |
| int bytes = mtd->writesize; |
| int cached = writelen > bytes && page != blockmask; |
| uint8_t *wbuf = buf; |
| |
| /* Partial page write ? */ |
| if (unlikely(column || writelen < (mtd->writesize - 1))) { |
| cached = 0; |
| bytes = min_t(int, bytes - column, (int) writelen); |
| chip->pagebuf = -1; |
| memset(chip->buffers->databuf, 0xff, mtd->writesize); |
| memcpy(&chip->buffers->databuf[column], buf, bytes); |
| wbuf = chip->buffers->databuf; |
| } |
| |
| if (unlikely(oob)) |
| oob = nand_fill_oob(chip, oob, ops); |
| |
| ret = chip->write_page(mtd, chip, wbuf, page, cached, |
| (ops->mode == MTD_OOB_RAW)); |
| if (ret) |
| break; |
| |
| writelen -= bytes; |
| if (!writelen) |
| break; |
| |
| column = 0; |
| buf += bytes; |
| realpage++; |
| |
| page = realpage & chip->pagemask; |
| /* Check, if we cross a chip boundary */ |
| if (!page) { |
| chipnr++; |
| chip->select_chip(mtd, -1); |
| chip->select_chip(mtd, chipnr); |
| } |
| } |
| |
| ops->retlen = ops->len - writelen; |
| if (unlikely(oob)) |
| ops->oobretlen = ops->ooblen; |
| return ret; |
| } |
| |
| /** |
| * nand_write - [MTD Interface] NAND write with ECC |
| * @mtd: MTD device structure |
| * @to: offset to write to |
| * @len: number of bytes to write |
| * @retlen: pointer to variable to store the number of written bytes |
| * @buf: the data to write |
| * |
| * NAND write with ECC |
| */ |
| int nand_write(struct mtd_info *mtd, loff_t to, size_t len, |
| size_t *retlen, const uint8_t *buf) |
| { |
| struct nand_chip *chip = mtd->priv; |
| int ret; |
| |
| /* Do not allow reads past end of device */ |
| if ((to + len) > mtd->size) |
| return -EINVAL; |
| if (!len) |
| return 0; |
| |
| chip->ops.len = len; |
| chip->ops.datbuf = (uint8_t *)buf; |
| chip->ops.oobbuf = NULL; |
| |
| ret = nand_do_write_ops(mtd, to, &chip->ops); |
| |
| *retlen = chip->ops.retlen; |
| |
| return ret; |
| } |
| |
| /** |
| * nand_do_write_oob - [MTD Interface] NAND write out-of-band |
| * @mtd: MTD device structure |
| * @to: offset to write to |
| * @ops: oob operation description structure |
| * |
| * NAND write out-of-band |
| */ |
| static int nand_do_write_oob(struct mtd_info *mtd, loff_t to, |
| struct mtd_oob_ops *ops) |
| { |
| int chipnr, page, status, len; |
| struct nand_chip *chip = mtd->priv; |
| |
| MTD_DEBUG(MTD_DEBUG_LEVEL3, "nand_write_oob: to = 0x%08x, len = %i\n", |
| (unsigned int)to, (int)ops->ooblen); |
| |
| if (ops->mode == MTD_OOB_AUTO) |
| len = chip->ecc.layout->oobavail; |
| else |
| len = mtd->oobsize; |
| |
| /* Do not allow write past end of page */ |
| if ((ops->ooboffs + ops->ooblen) > len) { |
| MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_write_oob: " |
| "Attempt to write past end of page\n"); |
| return -EINVAL; |
| } |
| |
| if (unlikely(ops->ooboffs >= len)) { |
| MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_read_oob: " |
| "Attempt to start write outside oob\n"); |
| return -EINVAL; |
| } |
| |
| /* Do not allow reads past end of device */ |
| if (unlikely(to >= mtd->size || |
| ops->ooboffs + ops->ooblen > |
| ((mtd->size >> chip->page_shift) - |
| (to >> chip->page_shift)) * len)) { |
| MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_read_oob: " |
| "Attempt write beyond end of device\n"); |
| return -EINVAL; |
| } |
| |
| chipnr = (int)(to >> chip->chip_shift); |
| chip->select_chip(mtd, chipnr); |
| |
| /* Shift to get page */ |
| page = (int)(to >> chip->page_shift); |
| |
| /* |
| * Reset the chip. Some chips (like the Toshiba TC5832DC found in one |
| * of my DiskOnChip 2000 test units) will clear the whole data page too |
| * if we don't do this. I have no clue why, but I seem to have 'fixed' |
| * it in the doc2000 driver in August 1999. dwmw2. |
| */ |
| chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); |
| |
| /* Check, if it is write protected */ |
| if (nand_check_wp(mtd)) |
| return -EROFS; |
| |
| /* Invalidate the page cache, if we write to the cached page */ |
| if (page == chip->pagebuf) |
| chip->pagebuf = -1; |
| |
| memset(chip->oob_poi, 0xff, mtd->oobsize); |
| nand_fill_oob(chip, ops->oobbuf, ops); |
| status = chip->ecc.write_oob(mtd, chip, page & chip->pagemask); |
| memset(chip->oob_poi, 0xff, mtd->oobsize); |
| |
| if (status) |
| return status; |
| |
| ops->oobretlen = ops->ooblen; |
| |
| return 0; |
| } |
| |
| /** |
| * nand_write_oob - [MTD Interface] NAND write data and/or out-of-band |
| * @mtd: MTD device structure |
| * @to: offset to write to |
| * @ops: oob operation description structure |
| */ |
| int nand_write_oob(struct mtd_info *mtd, loff_t to, |
| struct mtd_oob_ops *ops) |
| { |
| int ret = -ENOSYS; |
| |
| ops->retlen = 0; |
| |
| /* Do not allow writes past end of device */ |
| if (ops->datbuf && (to + ops->len) > mtd->size) { |
| MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_read_oob: " |
| "Attempt read beyond end of device\n"); |
| return -EINVAL; |
| } |
| |
| switch(ops->mode) { |
| case MTD_OOB_PLACE: |
| case MTD_OOB_AUTO: |
| case MTD_OOB_RAW: |
| break; |
| |
| default: |
| goto out; |
| } |
| |
| if (!ops->datbuf) |
| ret = nand_do_write_oob(mtd, to, ops); |
| else |
| ret = nand_do_write_ops(mtd, to, ops); |
| |
| out: |
| return ret; |
| } |
| |
| /** |
| * single_erease_cmd - [GENERIC] NAND standard block erase command function |
| * @mtd: MTD device structure |
| * @page: the page address of the block which will be erased |
| * |
| * Standard erase command for NAND chips |
| */ |
| void single_erase_cmd(struct mtd_info *mtd, int page) |
| { |
| struct nand_chip *chip = mtd->priv; |
| /* Send commands to erase a block */ |
| chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page); |
| chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1); |
| } |
| |
| /** |
| * multi_erease_cmd - [GENERIC] AND specific block erase command function |
| * @mtd: MTD device structure |
| * @page: the page address of the block which will be erased |
| * |
| * AND multi block erase command function |
| * Erase 4 consecutive blocks |
| */ |
| void multi_erase_cmd(struct mtd_info *mtd, int page) |
| { |
| struct nand_chip *chip = mtd->priv; |
| /* Send commands to erase a block */ |
| chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page++); |
| chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page++); |
| chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page++); |
| chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page); |
| chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1); |
| } |
| |
| /** |
| * nand_erase - [MTD Interface] erase block(s) |
| * @mtd: MTD device structure |
| * @instr: erase instruction |
| * |
| * Erase one ore more blocks |
| */ |
| int nand_erase(struct mtd_info *mtd, struct erase_info *instr) |
| { |
| return nand_erase_nand(mtd, instr, 0); |
| } |
| |
| #define BBT_PAGE_MASK 0xffffff3f |
| /** |
| * nand_erase_nand - [Internal] erase block(s) |
| * @mtd: MTD device structure |
| * @instr: erase instruction |
| * @allowbbt: allow erasing the bbt area |
| * |
| * Erase one ore more blocks |
| */ |
| int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr, |
| int allowbbt) |
| { |
| int page, len, status, pages_per_block, ret, chipnr; |
| struct nand_chip *chip = mtd->priv; |
| int rewrite_bbt[NAND_MAX_CHIPS]={0}; |
| unsigned int bbt_masked_page = 0xffffffff; |
| |
| MTD_DEBUG(MTD_DEBUG_LEVEL3, "nand_erase: start = 0x%08x, len = %i\n", |
| (unsigned int)instr->addr, (unsigned int)instr->len); |
| |
| /* Start address must align on block boundary */ |
| if (instr->addr & ((1 << chip->phys_erase_shift) - 1)) { |
| MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_erase: Unaligned address\n"); |
| return -EINVAL; |
| } |
| |
| /* Length must align on block boundary */ |
| if (instr->len & ((1 << chip->phys_erase_shift) - 1)) { |
| MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_erase: " |
| "Length not block aligned\n"); |
| return -EINVAL; |
| } |
| |
| /* Do not allow erase past end of device */ |
| if ((instr->len + instr->addr) > mtd->size) { |
| MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_erase: " |
| "Erase past end of device\n"); |
| return -EINVAL; |
| } |
| |
| instr->fail_addr = 0xffffffff; |
| |
| /* Shift to get first page */ |
| page = (int)(instr->addr >> chip->page_shift); |
| chipnr = (int)(instr->addr >> chip->chip_shift); |
| |
| /* Calculate pages in each block */ |
| pages_per_block = 1 << (chip->phys_erase_shift - chip->page_shift); |
| |
| /* Select the NAND device */ |
| chip->select_chip(mtd, chipnr); |
| |
| /* Check, if it is write protected */ |
| if (nand_check_wp(mtd)) { |
| MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_erase: " |
| "Device is write protected!!!\n"); |
| instr->state = MTD_ERASE_FAILED; |
| goto erase_exit; |
| } |
| |
| /* |
| * If BBT requires refresh, set the BBT page mask to see if the BBT |
| * should be rewritten. Otherwise the mask is set to 0xffffffff which |
| * can not be matched. This is also done when the bbt is actually |
| * erased to avoid recusrsive updates |
| */ |
| if (chip->options & BBT_AUTO_REFRESH && !allowbbt) |
| bbt_masked_page = chip->bbt_td->pages[chipnr] & BBT_PAGE_MASK; |
| |
| /* Loop through the pages */ |
| len = instr->len; |
| |
| instr->state = MTD_ERASING; |
| |
| while (len) { |
| /* |
| * heck if we have a bad block, we do not erase bad blocks ! |
| */ |
| if (nand_block_checkbad(mtd, ((loff_t) page) << |
| chip->page_shift, 0, allowbbt)) { |
| printk(KERN_WARNING "nand_erase: attempt to erase a " |
| "bad block at page 0x%08x\n", page); |
| instr->state = MTD_ERASE_FAILED; |
| goto erase_exit; |
| } |
| |
| /* |
| * Invalidate the page cache, if we erase the block which |
| * contains the current cached page |
| */ |
| if (page <= chip->pagebuf && chip->pagebuf < |
| (page + pages_per_block)) |
| chip->pagebuf = -1; |
| |
| chip->erase_cmd(mtd, page & chip->pagemask); |
| |
| status = chip->waitfunc(mtd, chip); |
| |
| /* |
| * See if operation failed and additional status checks are |
| * available |
| */ |
| if ((status & NAND_STATUS_FAIL) && (chip->errstat)) |
| status = chip->errstat(mtd, chip, FL_ERASING, |
| status, page); |
| |
| /* See if block erase succeeded */ |
| if (status & NAND_STATUS_FAIL) { |
| MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_erase: " |
| "Failed erase, page 0x%08x\n", page); |
| instr->state = MTD_ERASE_FAILED; |
| instr->fail_addr = (page << chip->page_shift); |
| goto erase_exit; |
| } |
| |
| /* |
| * If BBT requires refresh, set the BBT rewrite flag to the |
| * page being erased |
| */ |
| if (bbt_masked_page != 0xffffffff && |
| (page & BBT_PAGE_MASK) == bbt_masked_page) |
| rewrite_bbt[chipnr] = (page << chip->page_shift); |
| |
| /* Increment page address and decrement length */ |
| len -= (1 << chip->phys_erase_shift); |
| page += pages_per_block; |
| |
| /* Check, if we cross a chip boundary */ |
| if (len && !(page & chip->pagemask)) { |
| chipnr++; |
| chip->select_chip(mtd, -1); |
| chip->select_chip(mtd, chipnr); |
| |
| /* |
| * If BBT requires refresh and BBT-PERCHIP, set the BBT |
| * page mask to see if this BBT should be rewritten |
| */ |
| if (bbt_masked_page != 0xffffffff && |
| (chip->bbt_td->options & NAND_BBT_PERCHIP)) |
| bbt_masked_page = chip->bbt_td->pages[chipnr] & |
| BBT_PAGE_MASK; |
| } |
| } |
| instr->state = MTD_ERASE_DONE; |
| |
| erase_exit: |
| |
| ret = instr->state == MTD_ERASE_DONE ? 0 : -EIO; |
| |
| /* Do call back function */ |
| if (!ret) |
| mtd_erase_callback(instr); |
| |
| /* |
| * If BBT requires refresh and erase was successful, rewrite any |
| * selected bad block tables |
| */ |
| if (bbt_masked_page == 0xffffffff || ret) |
| return ret; |
| |
| #ifdef CONFIG_NAND_BBT |
| for (chipnr = 0; chipnr < chip->numchips; chipnr++) { |
| if (!rewrite_bbt[chipnr]) |
| continue; |
| /* update the BBT for chip */ |
| MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_erase_nand: nand_update_bbt " |
| "(%d:0x%0x 0x%0x)\n", chipnr, rewrite_bbt[chipnr], |
| chip->bbt_td->pages[chipnr]); |
| nand_update_bbt(mtd, rewrite_bbt[chipnr]); |
| } |
| #endif |
| /* Return more or less happy */ |
| return ret; |
| } |
| |
| /** |
| * nand_block_markbad - [MTD Interface] Mark block at the given offset as bad |
| * @mtd: MTD device structure |
| * @ofs: offset relative to mtd start |
| */ |
| int nand_block_markbad(struct mtd_info *mtd, loff_t ofs) |
| { |
| struct nand_chip *chip = mtd->priv; |
| int ret; |
| |
| if ((ret = nand_block_isbad(mtd, ofs))) { |
| /* If it was bad already, return success and do nothing. */ |
| if (ret > 0) |
| return 0; |
| return ret; |
| } |
| |
| return chip->block_markbad(mtd, ofs); |
| } |