| TUNNEL-MIB DEFINITIONS ::= BEGIN |
| |
| IMPORTS |
| MODULE-IDENTITY, OBJECT-TYPE, transmission, |
| Integer32, IpAddress FROM SNMPv2-SMI -- [RFC2578] |
| |
| RowStatus, StorageType FROM SNMPv2-TC -- [RFC2579] |
| |
| MODULE-COMPLIANCE, |
| OBJECT-GROUP FROM SNMPv2-CONF -- [RFC2580] |
| |
| InetAddressType, |
| InetAddress FROM INET-ADDRESS-MIB -- [RFC4001] |
| |
| IPv6FlowLabelOrAny FROM IPV6-FLOW-LABEL-MIB -- [RFC3595] |
| |
| ifIndex, |
| InterfaceIndexOrZero FROM IF-MIB -- [RFC2863] |
| |
| IANAtunnelType FROM IANAifType-MIB; -- [IFTYPE] |
| |
| tunnelMIB MODULE-IDENTITY |
| LAST-UPDATED "200505160000Z" -- May 16, 2005 |
| ORGANIZATION "IETF IP Version 6 (IPv6) Working Group" |
| CONTACT-INFO |
| " Dave Thaler |
| Microsoft Corporation |
| One Microsoft Way |
| Redmond, WA 98052-6399 |
| EMail: dthaler@microsoft.com" |
| DESCRIPTION |
| "The MIB module for management of IP Tunnels, |
| independent of the specific encapsulation scheme in |
| use. |
| |
| Copyright (C) The Internet Society (2005). This |
| version of this MIB module is part of RFC 4087; see |
| the RFC itself for full legal notices." |
| |
| |
| |
| REVISION "200505160000Z" -- May 16, 2005 |
| DESCRIPTION |
| "IPv4-specific objects were deprecated, including |
| tunnelIfLocalAddress, tunnelIfRemoteAddress, the |
| tunnelConfigTable, and the tunnelMIBBasicGroup. |
| |
| Added IP version-agnostic objects that should be used |
| instead, including tunnelIfAddressType, |
| tunnelIfLocalInetAddress, tunnelIfRemoteInetAddress, |
| the tunnelInetConfigTable, and the |
| tunnelIMIBInetGroup. |
| |
| The new tunnelIfLocalInetAddress and |
| tunnelIfRemoteInetAddress objects are read-write, |
| rather than read-only. |
| |
| Updated DESCRIPTION clauses of existing version- |
| agnostic objects (e.g., tunnelIfTOS) that contained |
| IPv4-specific text to cover IPv6 as well. |
| |
| Added tunnelIfFlowLabel for tunnels over IPv6. |
| |
| The encapsulation method was previously an INTEGER |
| type, and is now an IANA-maintained textual |
| convention. |
| |
| Published as RFC 4087." |
| REVISION "199908241200Z" -- August 24, 1999 |
| DESCRIPTION |
| "Initial version, published as RFC 2667." |
| ::= { transmission 131 } |
| |
| tunnelMIBObjects OBJECT IDENTIFIER ::= { tunnelMIB 1 } |
| |
| tunnel OBJECT IDENTIFIER ::= { tunnelMIBObjects 1 } |
| |
| -- the IP Tunnel MIB-Group |
| -- |
| -- a collection of objects providing information about |
| -- IP Tunnels |
| |
| tunnelIfTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF TunnelIfEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The (conceptual) table containing information on |
| configured tunnels." |
| |
| |
| |
| ::= { tunnel 1 } |
| |
| tunnelIfEntry OBJECT-TYPE |
| SYNTAX TunnelIfEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "An entry (conceptual row) containing the information |
| on a particular configured tunnel." |
| INDEX { ifIndex } |
| ::= { tunnelIfTable 1 } |
| |
| TunnelIfEntry ::= SEQUENCE { |
| tunnelIfLocalAddress IpAddress, -- deprecated |
| tunnelIfRemoteAddress IpAddress, -- deprecated |
| tunnelIfEncapsMethod IANAtunnelType, |
| tunnelIfHopLimit Integer32, |
| tunnelIfSecurity INTEGER, |
| tunnelIfTOS Integer32, |
| tunnelIfFlowLabel IPv6FlowLabelOrAny, |
| tunnelIfAddressType InetAddressType, |
| tunnelIfLocalInetAddress InetAddress, |
| tunnelIfRemoteInetAddress InetAddress, |
| tunnelIfEncapsLimit Integer32 |
| } |
| |
| tunnelIfLocalAddress OBJECT-TYPE |
| SYNTAX IpAddress |
| MAX-ACCESS read-only |
| STATUS deprecated |
| DESCRIPTION |
| "The address of the local endpoint of the tunnel |
| (i.e., the source address used in the outer IP |
| header), or 0.0.0.0 if unknown or if the tunnel is |
| over IPv6. |
| |
| Since this object does not support IPv6, it is |
| deprecated in favor of tunnelIfLocalInetAddress." |
| ::= { tunnelIfEntry 1 } |
| |
| tunnelIfRemoteAddress OBJECT-TYPE |
| SYNTAX IpAddress |
| MAX-ACCESS read-only |
| STATUS deprecated |
| DESCRIPTION |
| "The address of the remote endpoint of the tunnel |
| (i.e., the destination address used in the outer IP |
| header), or 0.0.0.0 if unknown, or an IPv6 address, or |
| |
| |
| |
| the tunnel is not a point-to-point link (e.g., if it |
| is a 6to4 tunnel). |
| |
| Since this object does not support IPv6, it is |
| deprecated in favor of tunnelIfRemoteInetAddress." |
| ::= { tunnelIfEntry 2 } |
| |
| tunnelIfEncapsMethod OBJECT-TYPE |
| SYNTAX IANAtunnelType |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The encapsulation method used by the tunnel." |
| ::= { tunnelIfEntry 3 } |
| |
| tunnelIfHopLimit OBJECT-TYPE |
| SYNTAX Integer32 (0 | 1..255) |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The IPv4 TTL or IPv6 Hop Limit to use in the outer IP |
| header. A value of 0 indicates that the value is |
| copied from the payload's header." |
| ::= { tunnelIfEntry 4 } |
| |
| tunnelIfSecurity OBJECT-TYPE |
| SYNTAX INTEGER { |
| none(1), -- no security |
| ipsec(2), -- IPsec security |
| other(3) |
| } |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "The method used by the tunnel to secure the outer IP |
| header. The value ipsec indicates that IPsec is used |
| between the tunnel endpoints for authentication or |
| encryption or both. More specific security-related |
| information may be available in a MIB module for the |
| security protocol in use." |
| ::= { tunnelIfEntry 5 } |
| |
| tunnelIfTOS OBJECT-TYPE |
| SYNTAX Integer32 (-2..63) |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The method used to set the high 6 bits (the |
| |
| |
| |
| differentiated services codepoint) of the IPv4 TOS or |
| IPv6 Traffic Class in the outer IP header. A value of |
| -1 indicates that the bits are copied from the |
| payload's header. A value of -2 indicates that a |
| traffic conditioner is invoked and more information |
| may be available in a traffic conditioner MIB module. |
| A value between 0 and 63 inclusive indicates that the |
| bit field is set to the indicated value. |
| |
| Note: instead of the name tunnelIfTOS, a better name |
| would have been tunnelIfDSCPMethod, but the existing |
| name appeared in RFC 2667 and existing objects cannot |
| be renamed." |
| ::= { tunnelIfEntry 6 } |
| |
| tunnelIfFlowLabel OBJECT-TYPE |
| SYNTAX IPv6FlowLabelOrAny |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The method used to set the IPv6 Flow Label value. |
| This object need not be present in rows where |
| tunnelIfAddressType indicates the tunnel is not over |
| IPv6. A value of -1 indicates that a traffic |
| conditioner is invoked and more information may be |
| available in a traffic conditioner MIB. Any other |
| value indicates that the Flow Label field is set to |
| the indicated value." |
| ::= { tunnelIfEntry 7 } |
| |
| tunnelIfAddressType OBJECT-TYPE |
| SYNTAX InetAddressType |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The type of address in the corresponding |
| tunnelIfLocalInetAddress and tunnelIfRemoteInetAddress |
| objects." |
| ::= { tunnelIfEntry 8 } |
| |
| tunnelIfLocalInetAddress OBJECT-TYPE |
| SYNTAX InetAddress |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The address of the local endpoint of the tunnel |
| (i.e., the source address used in the outer IP |
| header). If the address is unknown, the value is |
| |
| |
| |
| 0.0.0.0 for IPv4 or :: for IPv6. The type of this |
| object is given by tunnelIfAddressType." |
| ::= { tunnelIfEntry 9 } |
| |
| tunnelIfRemoteInetAddress OBJECT-TYPE |
| SYNTAX InetAddress |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The address of the remote endpoint of the tunnel |
| (i.e., the destination address used in the outer IP |
| header). If the address is unknown or the tunnel is |
| not a point-to-point link (e.g., if it is a 6to4 |
| tunnel), the value is 0.0.0.0 for tunnels over IPv4 or |
| :: for tunnels over IPv6. The type of this object is |
| given by tunnelIfAddressType." |
| ::= { tunnelIfEntry 10 } |
| |
| tunnelIfEncapsLimit OBJECT-TYPE |
| SYNTAX Integer32 (-1 | 0..255) |
| MAX-ACCESS read-write |
| STATUS current |
| DESCRIPTION |
| "The maximum number of additional encapsulations |
| permitted for packets undergoing encapsulation at this |
| node. A value of -1 indicates that no limit is |
| present (except as a result of the packet size)." |
| REFERENCE "RFC 2473, section 4.1.1" |
| ::= { tunnelIfEntry 11 } |
| |
| tunnelConfigTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF TunnelConfigEntry |
| MAX-ACCESS not-accessible |
| STATUS deprecated |
| DESCRIPTION |
| "The (conceptual) table containing information on |
| configured tunnels. This table can be used to map a |
| set of tunnel endpoints to the associated ifIndex |
| value. It can also be used for row creation. Note |
| that every row in the tunnelIfTable with a fixed IPv4 |
| destination address should have a corresponding row in |
| the tunnelConfigTable, regardless of whether it was |
| created via SNMP. |
| |
| Since this table does not support IPv6, it is |
| deprecated in favor of tunnelInetConfigTable." |
| ::= { tunnel 2 } |
| |
| |
| |
| |
| tunnelConfigEntry OBJECT-TYPE |
| SYNTAX TunnelConfigEntry |
| MAX-ACCESS not-accessible |
| STATUS deprecated |
| DESCRIPTION |
| "An entry (conceptual row) containing the information |
| on a particular configured tunnel. |
| |
| Since this entry does not support IPv6, it is |
| deprecated in favor of tunnelInetConfigEntry." |
| INDEX { tunnelConfigLocalAddress, |
| tunnelConfigRemoteAddress, |
| tunnelConfigEncapsMethod, |
| tunnelConfigID } |
| ::= { tunnelConfigTable 1 } |
| |
| TunnelConfigEntry ::= SEQUENCE { |
| tunnelConfigLocalAddress IpAddress, |
| tunnelConfigRemoteAddress IpAddress, |
| tunnelConfigEncapsMethod IANAtunnelType, |
| tunnelConfigID Integer32, |
| tunnelConfigIfIndex InterfaceIndexOrZero, |
| tunnelConfigStatus RowStatus |
| } |
| |
| tunnelConfigLocalAddress OBJECT-TYPE |
| SYNTAX IpAddress |
| MAX-ACCESS not-accessible |
| STATUS deprecated |
| DESCRIPTION |
| "The address of the local endpoint of the tunnel, or |
| 0.0.0.0 if the device is free to choose any of its |
| addresses at tunnel establishment time. |
| |
| Since this object does not support IPv6, it is |
| deprecated in favor of tunnelInetConfigLocalAddress." |
| ::= { tunnelConfigEntry 1 } |
| |
| tunnelConfigRemoteAddress OBJECT-TYPE |
| SYNTAX IpAddress |
| MAX-ACCESS not-accessible |
| STATUS deprecated |
| DESCRIPTION |
| "The address of the remote endpoint of the tunnel. |
| |
| Since this object does not support IPv6, it is |
| deprecated in favor of tunnelInetConfigRemoteAddress." |
| ::= { tunnelConfigEntry 2 } |
| |
| |
| |
| tunnelConfigEncapsMethod OBJECT-TYPE |
| SYNTAX IANAtunnelType |
| MAX-ACCESS not-accessible |
| STATUS deprecated |
| DESCRIPTION |
| "The encapsulation method used by the tunnel. |
| |
| Since this object does not support IPv6, it is |
| deprecated in favor of tunnelInetConfigEncapsMethod." |
| ::= { tunnelConfigEntry 3 } |
| |
| tunnelConfigID OBJECT-TYPE |
| SYNTAX Integer32 (1..2147483647) |
| MAX-ACCESS not-accessible |
| STATUS deprecated |
| DESCRIPTION |
| "An identifier used to distinguish between multiple |
| tunnels of the same encapsulation method, with the |
| same endpoints. If the encapsulation protocol only |
| allows one tunnel per set of endpoint addresses (such |
| as for GRE or IP-in-IP), the value of this object is |
| 1. For encapsulation methods (such as L2F) which |
| allow multiple parallel tunnels, the manager is |
| responsible for choosing any ID which does not |
| conflict with an existing row, such as choosing a |
| random number. |
| |
| Since this object does not support IPv6, it is |
| deprecated in favor of tunnelInetConfigID." |
| ::= { tunnelConfigEntry 4 } |
| |
| tunnelConfigIfIndex OBJECT-TYPE |
| SYNTAX InterfaceIndexOrZero |
| MAX-ACCESS read-only |
| STATUS deprecated |
| DESCRIPTION |
| "If the value of tunnelConfigStatus for this row is |
| active, then this object contains the value of ifIndex |
| corresponding to the tunnel interface. A value of 0 |
| is not legal in the active state, and means that the |
| interface index has not yet been assigned. |
| |
| Since this object does not support IPv6, it is |
| deprecated in favor of tunnelInetConfigIfIndex." |
| ::= { tunnelConfigEntry 5 } |
| |
| tunnelConfigStatus OBJECT-TYPE |
| SYNTAX RowStatus |
| |
| |
| |
| MAX-ACCESS read-create |
| STATUS deprecated |
| DESCRIPTION |
| "The status of this row, by which new entries may be |
| created, or old entries deleted from this table. The |
| agent need not support setting this object to |
| createAndWait or notInService since there are no other |
| writable objects in this table, and writable objects |
| in rows of corresponding tables such as the |
| tunnelIfTable may be modified while this row is |
| active. |
| |
| To create a row in this table for an encapsulation |
| method which does not support multiple parallel |
| tunnels with the same endpoints, the management |
| station should simply use a tunnelConfigID of 1, and |
| set tunnelConfigStatus to createAndGo. For |
| encapsulation methods such as L2F which allow multiple |
| parallel tunnels, the management station may select a |
| pseudo-random number to use as the tunnelConfigID and |
| set tunnelConfigStatus to createAndGo. In the event |
| that this ID is already in use and an |
| inconsistentValue is returned in response to the set |
| operation, the management station should simply select |
| a new pseudo-random number and retry the operation. |
| |
| Creating a row in this table will cause an interface |
| index to be assigned by the agent in an |
| implementation-dependent manner, and corresponding |
| rows will be instantiated in the ifTable and the |
| tunnelIfTable. The status of this row will become |
| active as soon as the agent assigns the interface |
| index, regardless of whether the interface is |
| operationally up. |
| |
| Deleting a row in this table will likewise delete the |
| corresponding row in the ifTable and in the |
| tunnelIfTable. |
| |
| Since this object does not support IPv6, it is |
| deprecated in favor of tunnelInetConfigStatus." |
| ::= { tunnelConfigEntry 6 } |
| |
| tunnelInetConfigTable OBJECT-TYPE |
| SYNTAX SEQUENCE OF TunnelInetConfigEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| |
| |
| |
| "The (conceptual) table containing information on |
| configured tunnels. This table can be used to map a |
| set of tunnel endpoints to the associated ifIndex |
| value. It can also be used for row creation. Note |
| that every row in the tunnelIfTable with a fixed |
| destination address should have a corresponding row in |
| the tunnelInetConfigTable, regardless of whether it |
| was created via SNMP." |
| ::= { tunnel 3 } |
| |
| tunnelInetConfigEntry OBJECT-TYPE |
| SYNTAX TunnelInetConfigEntry |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "An entry (conceptual row) containing the information |
| on a particular configured tunnel. Note that there is |
| a 128 subid maximum for object OIDs. Implementers |
| need to be aware that if the total number of octets in |
| tunnelInetConfigLocalAddress and |
| tunnelInetConfigRemoteAddress exceeds 110 then OIDs of |
| column instances in this table will have more than 128 |
| sub-identifiers and cannot be accessed using SNMPv1, |
| SNMPv2c, or SNMPv3. In practice this is not expected |
| to be a problem since IPv4 and IPv6 addresses will not |
| cause the limit to be reached, but if other types are |
| supported by an agent, care must be taken to ensure |
| that the sum of the lengths do not cause the limit to |
| be exceeded." |
| INDEX { tunnelInetConfigAddressType, |
| tunnelInetConfigLocalAddress, |
| tunnelInetConfigRemoteAddress, |
| tunnelInetConfigEncapsMethod, |
| tunnelInetConfigID } |
| ::= { tunnelInetConfigTable 1 } |
| |
| TunnelInetConfigEntry ::= SEQUENCE { |
| tunnelInetConfigAddressType InetAddressType, |
| tunnelInetConfigLocalAddress InetAddress, |
| tunnelInetConfigRemoteAddress InetAddress, |
| tunnelInetConfigEncapsMethod IANAtunnelType, |
| tunnelInetConfigID Integer32, |
| tunnelInetConfigIfIndex InterfaceIndexOrZero, |
| tunnelInetConfigStatus RowStatus, |
| tunnelInetConfigStorageType StorageType |
| } |
| |
| tunnelInetConfigAddressType OBJECT-TYPE |
| |
| |
| |
| SYNTAX InetAddressType |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The address type over which the tunnel encapsulates |
| packets." |
| ::= { tunnelInetConfigEntry 1 } |
| |
| tunnelInetConfigLocalAddress OBJECT-TYPE |
| SYNTAX InetAddress |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The address of the local endpoint of the tunnel, or |
| 0.0.0.0 (for IPv4) or :: (for IPv6) if the device is |
| free to choose any of its addresses at tunnel |
| establishment time." |
| ::= { tunnelInetConfigEntry 2 } |
| |
| tunnelInetConfigRemoteAddress OBJECT-TYPE |
| SYNTAX InetAddress |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The address of the remote endpoint of the tunnel." |
| ::= { tunnelInetConfigEntry 3 } |
| |
| tunnelInetConfigEncapsMethod OBJECT-TYPE |
| SYNTAX IANAtunnelType |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "The encapsulation method used by the tunnel." |
| ::= { tunnelInetConfigEntry 4 } |
| |
| tunnelInetConfigID OBJECT-TYPE |
| SYNTAX Integer32 (1..2147483647) |
| MAX-ACCESS not-accessible |
| STATUS current |
| DESCRIPTION |
| "An identifier used to distinguish between multiple |
| tunnels of the same encapsulation method, with the |
| same endpoints. If the encapsulation protocol only |
| allows one tunnel per set of endpoint addresses (such |
| as for GRE or IP-in-IP), the value of this object is |
| 1. For encapsulation methods (such as L2F) which |
| allow multiple parallel tunnels, the manager is |
| responsible for choosing any ID which does not |
| |
| |
| |
| conflict with an existing row, such as choosing a |
| random number." |
| ::= { tunnelInetConfigEntry 5 } |
| |
| tunnelInetConfigIfIndex OBJECT-TYPE |
| SYNTAX InterfaceIndexOrZero |
| MAX-ACCESS read-only |
| STATUS current |
| DESCRIPTION |
| "If the value of tunnelInetConfigStatus for this row |
| is active, then this object contains the value of |
| ifIndex corresponding to the tunnel interface. A |
| value of 0 is not legal in the active state, and means |
| that the interface index has not yet been assigned." |
| ::= { tunnelInetConfigEntry 6 } |
| |
| tunnelInetConfigStatus OBJECT-TYPE |
| SYNTAX RowStatus |
| MAX-ACCESS read-create |
| STATUS current |
| DESCRIPTION |
| "The status of this row, by which new entries may be |
| created, or old entries deleted from this table. The |
| agent need not support setting this object to |
| createAndWait or notInService since there are no other |
| writable objects in this table, and writable objects |
| in rows of corresponding tables such as the |
| tunnelIfTable may be modified while this row is |
| active. |
| |
| To create a row in this table for an encapsulation |
| method which does not support multiple parallel |
| tunnels with the same endpoints, the management |
| station should simply use a tunnelInetConfigID of 1, |
| and set tunnelInetConfigStatus to createAndGo. For |
| encapsulation methods such as L2F which allow multiple |
| parallel tunnels, the management station may select a |
| pseudo-random number to use as the tunnelInetConfigID |
| and set tunnelInetConfigStatus to createAndGo. In the |
| event that this ID is already in use and an |
| inconsistentValue is returned in response to the set |
| operation, the management station should simply select |
| a new pseudo-random number and retry the operation. |
| |
| Creating a row in this table will cause an interface |
| index to be assigned by the agent in an |
| implementation-dependent manner, and corresponding |
| rows will be instantiated in the ifTable and the |
| |
| |
| |
| tunnelIfTable. The status of this row will become |
| active as soon as the agent assigns the interface |
| index, regardless of whether the interface is |
| operationally up. |
| |
| Deleting a row in this table will likewise delete the |
| corresponding row in the ifTable and in the |
| tunnelIfTable." |
| ::= { tunnelInetConfigEntry 7 } |
| |
| tunnelInetConfigStorageType OBJECT-TYPE |
| SYNTAX StorageType |
| MAX-ACCESS read-create |
| STATUS current |
| DESCRIPTION |
| "The storage type of this row. If the row is |
| permanent(4), no objects in the row need be writable." |
| ::= { tunnelInetConfigEntry 8 } |
| |
| -- conformance information |
| |
| tunnelMIBConformance |
| OBJECT IDENTIFIER ::= { tunnelMIB 2 } |
| tunnelMIBCompliances |
| OBJECT IDENTIFIER ::= { tunnelMIBConformance 1 } |
| tunnelMIBGroups OBJECT IDENTIFIER ::= { tunnelMIBConformance 2 } |
| |
| -- compliance statements |
| |
| tunnelMIBCompliance MODULE-COMPLIANCE |
| STATUS deprecated |
| DESCRIPTION |
| "The (deprecated) IPv4-only compliance statement for |
| the IP Tunnel MIB. |
| |
| This is deprecated in favor of |
| tunnelMIBInetFullCompliance and |
| tunnelMIBInetReadOnlyCompliance." |
| MODULE -- this module |
| MANDATORY-GROUPS { tunnelMIBBasicGroup } |
| |
| OBJECT tunnelIfHopLimit |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "Write access is not required." |
| |
| OBJECT tunnelIfTOS |
| MIN-ACCESS read-only |
| |
| |
| |
| DESCRIPTION |
| "Write access is not required." |
| |
| OBJECT tunnelConfigStatus |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "Write access is not required." |
| ::= { tunnelMIBCompliances 1 } |
| |
| tunnelMIBInetFullCompliance MODULE-COMPLIANCE |
| STATUS current |
| DESCRIPTION |
| "The full compliance statement for the IP Tunnel MIB." |
| MODULE -- this module |
| MANDATORY-GROUPS { tunnelMIBInetGroup } |
| |
| OBJECT tunnelIfAddressType |
| SYNTAX InetAddressType { ipv4(1), ipv6(2), |
| ipv4z(3), ipv6z(4) } |
| DESCRIPTION |
| "An implementation is only required to support IPv4 |
| and/or IPv6 addresses. An implementation only needs to |
| support the addresses it actually supports on the |
| device." |
| ::= { tunnelMIBCompliances 2 } |
| |
| tunnelMIBInetReadOnlyCompliance MODULE-COMPLIANCE |
| STATUS current |
| DESCRIPTION |
| "The read-only compliance statement for the IP Tunnel |
| MIB." |
| MODULE -- this module |
| MANDATORY-GROUPS { tunnelMIBInetGroup } |
| |
| OBJECT tunnelIfHopLimit |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "Write access is not required." |
| |
| OBJECT tunnelIfTOS |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "Write access is not required." |
| |
| OBJECT tunnelIfFlowLabel |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "Write access is not required." |
| |
| |
| |
| OBJECT tunnelIfAddressType |
| SYNTAX InetAddressType { ipv4(1), ipv6(2), |
| ipv4z(3), ipv6z(4) } |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "Write access is not required. |
| |
| An implementation is only required to support IPv4 |
| and/or IPv6 addresses. An implementation only needs to |
| support the addresses it actually supports on the |
| device." |
| |
| OBJECT tunnelIfLocalInetAddress |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "Write access is not required." |
| |
| OBJECT tunnelIfRemoteInetAddress |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "Write access is not required." |
| |
| OBJECT tunnelIfEncapsLimit |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "Write access is not required." |
| |
| OBJECT tunnelInetConfigStatus |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "Write access is not required, and active is the only |
| status that needs to be supported." |
| |
| OBJECT tunnelInetConfigStorageType |
| MIN-ACCESS read-only |
| DESCRIPTION |
| "Write access is not required." |
| ::= { tunnelMIBCompliances 3 } |
| |
| -- units of conformance |
| |
| tunnelMIBBasicGroup OBJECT-GROUP |
| OBJECTS { tunnelIfLocalAddress, tunnelIfRemoteAddress, |
| tunnelIfEncapsMethod, tunnelIfHopLimit, tunnelIfTOS, |
| tunnelIfSecurity, tunnelConfigIfIndex, tunnelConfigStatus } |
| STATUS deprecated |
| DESCRIPTION |
| "A collection of objects to support basic management |
| |
| |
| |
| of IPv4 Tunnels. Since this group cannot support |
| IPv6, it is deprecated in favor of |
| tunnelMIBInetGroup." |
| ::= { tunnelMIBGroups 1 } |
| |
| tunnelMIBInetGroup OBJECT-GROUP |
| OBJECTS { tunnelIfAddressType, tunnelIfLocalInetAddress, |
| tunnelIfRemoteInetAddress, tunnelIfEncapsMethod, |
| tunnelIfEncapsLimit, |
| tunnelIfHopLimit, tunnelIfTOS, tunnelIfFlowLabel, |
| tunnelIfSecurity, tunnelInetConfigIfIndex, |
| tunnelInetConfigStatus, tunnelInetConfigStorageType } |
| STATUS current |
| DESCRIPTION |
| "A collection of objects to support basic management |
| of IPv4 and IPv6 Tunnels." |
| ::= { tunnelMIBGroups 2 } |
| |
| END |
