blob: 3090ff795d5e52db26555cc940a8c7247b808691 [file] [log] [blame]
IP-FORWARD-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
IpAddress, Integer32, Gauge32,
Counter32 FROM SNMPv2-SMI
RowStatus FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF
InterfaceIndexOrZero FROM IF-MIB
ip FROM IP-MIB
IANAipRouteProtocol FROM IANA-RTPROTO-MIB
InetAddress, InetAddressType,
InetAddressPrefixLength,
InetAutonomousSystemNumber FROM INET-ADDRESS-MIB;
ipForward MODULE-IDENTITY
LAST-UPDATED "200602010000Z"
ORGANIZATION
"IETF IPv6 Working Group
http://www.ietf.org/html.charters/ipv6-charter.html"
CONTACT-INFO
"Editor:
Brian Haberman
Johns Hopkins University - Applied Physics Laboratory
Mailstop 17-S442
11100 Johns Hopkins Road
Laurel MD, 20723-6099 USA
Phone: +1-443-778-1319
Email: brian@innovationslab.net
Send comments to <ipv6@ietf.org>"
DESCRIPTION
"The MIB module for the management of CIDR multipath IP
Routes.
Copyright (C) The Internet Society (2006). This version
of this MIB module is a part of RFC 4292; see the RFC
itself for full legal notices."
REVISION "200602010000Z"
DESCRIPTION
"IPv4/v6 version-independent revision. Minimal changes
were made to the original RFC 2096 MIB to allow easy
upgrade of existing IPv4 implementations to the
version-independent MIB. These changes include:
Adding inetCidrRouteDiscards as a replacement for the
deprecated ipRoutingDiscards and ipv6DiscardedRoutes
objects.
Adding a new conformance statement to support the
implementation of the IP Forwarding MIB in a
read-only mode.
The inetCidrRouteTable replaces the IPv4-specific
ipCidrRouteTable, its related objects, and related
conformance statements.
Published as RFC 4292."
REVISION "199609190000Z"
DESCRIPTION
"Revised to support CIDR routes.
Published as RFC 2096."
REVISION "199207022156Z"
DESCRIPTION
"Initial version, published as RFC 1354."
::= { ip 24 }
inetCidrRouteNumber OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of current inetCidrRouteTable entries that
are not invalid."
::= { ipForward 6 }
inetCidrRouteDiscards OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of valid route entries discarded from the
inetCidrRouteTable. Discarded route entries do not
appear in the inetCidrRouteTable. One possible reason
for discarding an entry would be to free-up buffer space
for other route table entries."
::= { ipForward 8 }
-- Inet CIDR Route Table
-- The Inet CIDR Route Table deprecates and replaces the
-- ipCidrRoute Table currently in the IP Forwarding Table MIB.
-- It adds IP protocol independence.
inetCidrRouteTable OBJECT-TYPE
SYNTAX SEQUENCE OF InetCidrRouteEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This entity's IP Routing table."
REFERENCE
"RFC 1213 Section 6.6, The IP Group"
::= { ipForward 7 }
inetCidrRouteEntry OBJECT-TYPE
SYNTAX InetCidrRouteEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A particular route to a particular destination, under a
particular policy (as reflected in the
inetCidrRoutePolicy object).
Dynamically created rows will survive an agent reboot.
Implementers need to be aware that if the total number
of elements (octets or sub-identifiers) in
inetCidrRouteDest, inetCidrRoutePolicy, and
inetCidrRouteNextHop exceeds 111, then OIDs of column
instances in this table will have more than 128 sub-
identifiers and cannot be accessed using SNMPv1,
SNMPv2c, or SNMPv3."
INDEX {
inetCidrRouteDestType,
inetCidrRouteDest,
inetCidrRoutePfxLen,
inetCidrRoutePolicy,
inetCidrRouteNextHopType,
inetCidrRouteNextHop
}
::= { inetCidrRouteTable 1 }
InetCidrRouteEntry ::= SEQUENCE {
inetCidrRouteDestType InetAddressType,
inetCidrRouteDest InetAddress,
inetCidrRoutePfxLen InetAddressPrefixLength,
inetCidrRoutePolicy OBJECT IDENTIFIER,
inetCidrRouteNextHopType InetAddressType,
inetCidrRouteNextHop InetAddress,
inetCidrRouteIfIndex InterfaceIndexOrZero,
inetCidrRouteType INTEGER,
inetCidrRouteProto IANAipRouteProtocol,
inetCidrRouteAge Gauge32,
inetCidrRouteNextHopAS InetAutonomousSystemNumber,
inetCidrRouteMetric1 Integer32,
inetCidrRouteMetric2 Integer32,
inetCidrRouteMetric3 Integer32,
inetCidrRouteMetric4 Integer32,
inetCidrRouteMetric5 Integer32,
inetCidrRouteStatus RowStatus
}
inetCidrRouteDestType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The type of the inetCidrRouteDest address, as defined
in the InetAddress MIB.
Only those address types that may appear in an actual
routing table are allowed as values of this object."
REFERENCE "RFC 4001"
::= { inetCidrRouteEntry 1 }
inetCidrRouteDest OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The destination IP address of this route.
The type of this address is determined by the value of
the inetCidrRouteDestType object.
The values for the index objects inetCidrRouteDest and
inetCidrRoutePfxLen must be consistent. When the value
of inetCidrRouteDest (excluding the zone index, if one
is present) is x, then the bitwise logical-AND
of x with the value of the mask formed from the
corresponding index object inetCidrRoutePfxLen MUST be
equal to x. If not, then the index pair is not
consistent and an inconsistentName error must be
returned on SET or CREATE requests."
::= { inetCidrRouteEntry 2 }
inetCidrRoutePfxLen OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indicates the number of leading one bits that form the
mask to be logical-ANDed with the destination address
before being compared to the value in the
inetCidrRouteDest field.
The values for the index objects inetCidrRouteDest and
inetCidrRoutePfxLen must be consistent. When the value
of inetCidrRouteDest (excluding the zone index, if one
is present) is x, then the bitwise logical-AND
of x with the value of the mask formed from the
corresponding index object inetCidrRoutePfxLen MUST be
equal to x. If not, then the index pair is not
consistent and an inconsistentName error must be
returned on SET or CREATE requests."
::= { inetCidrRouteEntry 3 }
inetCidrRoutePolicy OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is an opaque object without any defined
semantics. Its purpose is to serve as an additional
index that may delineate between multiple entries to
the same destination. The value { 0 0 } shall be used
as the default value for this object."
::= { inetCidrRouteEntry 4 }
inetCidrRouteNextHopType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The type of the inetCidrRouteNextHop address, as
defined in the InetAddress MIB.
Value should be set to unknown(0) for non-remote
routes.
Only those address types that may appear in an actual
routing table are allowed as values of this object."
REFERENCE "RFC 4001"
::= { inetCidrRouteEntry 5 }
inetCidrRouteNextHop OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"On remote routes, the address of the next system en
route. For non-remote routes, a zero length string.
The type of this address is determined by the value of
the inetCidrRouteNextHopType object."
::= { inetCidrRouteEntry 6 }
inetCidrRouteIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The ifIndex value that identifies the local interface
through which the next hop of this route should be
reached. A value of 0 is valid and represents the
scenario where no interface is specified."
::= { inetCidrRouteEntry 7 }
inetCidrRouteType OBJECT-TYPE
SYNTAX INTEGER {
other (1), -- not specified by this MIB
reject (2), -- route that discards traffic and
-- returns ICMP notification
local (3), -- local interface
remote (4), -- remote destination
blackhole(5) -- route that discards traffic
-- silently
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of route. Note that local(3) refers to a
route for which the next hop is the final destination;
remote(4) refers to a route for which the next hop is
not the final destination.
Routes that do not result in traffic forwarding or
rejection should not be displayed, even if the
implementation keeps them stored internally.
reject(2) refers to a route that, if matched, discards
the message as unreachable and returns a notification
(e.g., ICMP error) to the message sender. This is used
in some protocols as a means of correctly aggregating
routes.
blackhole(5) refers to a route that, if matched,
discards the message silently."
::= { inetCidrRouteEntry 8 }
inetCidrRouteProto OBJECT-TYPE
SYNTAX IANAipRouteProtocol
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The routing mechanism via which this route was learned.
Inclusion of values for gateway routing protocols is
not intended to imply that hosts should support those
protocols."
::= { inetCidrRouteEntry 9 }
inetCidrRouteAge OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds since this route was last updated
or otherwise determined to be correct. Note that no
semantics of 'too old' can be implied, except through
knowledge of the routing protocol by which the route
was learned."
::= { inetCidrRouteEntry 10 }
inetCidrRouteNextHopAS OBJECT-TYPE
SYNTAX InetAutonomousSystemNumber
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Autonomous System Number of the Next Hop. The
semantics of this object are determined by the routing-
protocol specified in the route's inetCidrRouteProto
value. When this object is unknown or not relevant, its
value should be set to zero."
DEFVAL { 0 }
::= { inetCidrRouteEntry 11 }
inetCidrRouteMetric1 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The primary routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's inetCidrRouteProto
value. If this metric is not used, its value should be
set to -1."
DEFVAL { -1 }
::= { inetCidrRouteEntry 12 }
inetCidrRouteMetric2 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's inetCidrRouteProto
value. If this metric is not used, its value should be
set to -1."
DEFVAL { -1 }
::= { inetCidrRouteEntry 13 }
inetCidrRouteMetric3 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's inetCidrRouteProto
value. If this metric is not used, its value should be
set to -1."
DEFVAL { -1 }
::= { inetCidrRouteEntry 14 }
inetCidrRouteMetric4 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's inetCidrRouteProto
value. If this metric is not used, its value should be
set to -1."
DEFVAL { -1 }
::= { inetCidrRouteEntry 15 }
inetCidrRouteMetric5 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's inetCidrRouteProto
value. If this metric is not used, its value should be
set to -1."
DEFVAL { -1 }
::= { inetCidrRouteEntry 16 }
inetCidrRouteStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The row status variable, used according to row
installation and removal conventions.
A row entry cannot be modified when the status is
marked as active(1)."
::= { inetCidrRouteEntry 17 }
-- Conformance information
ipForwardConformance
OBJECT IDENTIFIER ::= { ipForward 5 }
ipForwardGroups
OBJECT IDENTIFIER ::= { ipForwardConformance 1 }
ipForwardCompliances
OBJECT IDENTIFIER ::= { ipForwardConformance 2 }
-- Compliance statements
ipForwardFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"When this MIB is implemented for read-create, the
implementation can claim full compliance.
There are a number of INDEX objects that cannot be
represented in the form of OBJECT clauses in SMIv2,
but for which there are compliance requirements,
expressed in OBJECT clause form in this description:
-- OBJECT inetCidrRouteDestType
-- SYNTAX InetAddressType (ipv4(1), ipv6(2),
-- ipv4z(3), ipv6z(4))
-- DESCRIPTION
-- This MIB requires support for global and
-- non-global ipv4 and ipv6 addresses.
--
-- OBJECT inetCidrRouteDest
-- SYNTAX InetAddress (SIZE (4 | 8 | 16 | 20))
-- DESCRIPTION
-- This MIB requires support for global and
-- non-global IPv4 and IPv6 addresses.
--
-- OBJECT inetCidrRouteNextHopType
-- SYNTAX InetAddressType (unknown(0), ipv4(1),
-- ipv6(2), ipv4z(3)
-- ipv6z(4))
-- DESCRIPTION
-- This MIB requires support for global and
-- non-global ipv4 and ipv6 addresses.
--
-- OBJECT inetCidrRouteNextHop
-- SYNTAX InetAddress (SIZE (0 | 4 | 8 | 16 | 20))
-- DESCRIPTION
-- This MIB requires support for global and
-- non-global IPv4 and IPv6 addresses.
"
MODULE -- this module
MANDATORY-GROUPS { inetForwardCidrRouteGroup }
OBJECT inetCidrRouteStatus
SYNTAX RowStatus { active(1), notInService (2) }
WRITE-SYNTAX RowStatus { active(1), notInService (2),
createAndGo(4), destroy(6) }
DESCRIPTION "Support for createAndWait is not required."
::= { ipForwardCompliances 3 }
ipForwardReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"When this MIB is implemented without support for read-
create (i.e., in read-only mode), the implementation can
claim read-only compliance."
MODULE -- this module
MANDATORY-GROUPS { inetForwardCidrRouteGroup }
OBJECT inetCidrRouteIfIndex
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT inetCidrRouteType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT inetCidrRouteNextHopAS
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT inetCidrRouteMetric1
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT inetCidrRouteMetric2
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT inetCidrRouteMetric3
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT inetCidrRouteMetric4
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT inetCidrRouteMetric5
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT inetCidrRouteStatus
SYNTAX RowStatus { active(1) }
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { ipForwardCompliances 4 }
-- units of conformance
inetForwardCidrRouteGroup OBJECT-GROUP
OBJECTS { inetCidrRouteDiscards,
inetCidrRouteIfIndex, inetCidrRouteType,
inetCidrRouteProto, inetCidrRouteAge,
inetCidrRouteNextHopAS, inetCidrRouteMetric1,
inetCidrRouteMetric2, inetCidrRouteMetric3,
inetCidrRouteMetric4, inetCidrRouteMetric5,
inetCidrRouteStatus, inetCidrRouteNumber
}
STATUS current
DESCRIPTION
"The IP version-independent CIDR Route Table."
::= { ipForwardGroups 4 }
-- Deprecated Objects
ipCidrRouteNumber OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of current ipCidrRouteTable entries that are
not invalid. This object is deprecated in favor of
inetCidrRouteNumber and the inetCidrRouteTable."
::= { ipForward 3 }
-- IP CIDR Route Table
-- The IP CIDR Route Table obsoletes and replaces the ipRoute
-- Table current in MIB-I and MIB-II and the IP Forwarding Table.
-- It adds knowledge of the autonomous system of the next hop,
-- multiple next hops, policy routing, and Classless
-- Inter-Domain Routing.
ipCidrRouteTable OBJECT-TYPE
SYNTAX SEQUENCE OF IpCidrRouteEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This entity's IP Routing table. This table has been
deprecated in favor of the IP version neutral
inetCidrRouteTable."
REFERENCE
"RFC 1213 Section 6.6, The IP Group"
::= { ipForward 4 }
ipCidrRouteEntry OBJECT-TYPE
SYNTAX IpCidrRouteEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"A particular route to a particular destination, under a
particular policy."
INDEX {
ipCidrRouteDest,
ipCidrRouteMask,
ipCidrRouteTos,
ipCidrRouteNextHop
}
::= { ipCidrRouteTable 1 }
IpCidrRouteEntry ::= SEQUENCE {
ipCidrRouteDest IpAddress,
ipCidrRouteMask IpAddress,
ipCidrRouteTos Integer32,
ipCidrRouteNextHop IpAddress,
ipCidrRouteIfIndex Integer32,
ipCidrRouteType INTEGER,
ipCidrRouteProto INTEGER,
ipCidrRouteAge Integer32,
ipCidrRouteInfo OBJECT IDENTIFIER,
ipCidrRouteNextHopAS Integer32,
ipCidrRouteMetric1 Integer32,
ipCidrRouteMetric2 Integer32,
ipCidrRouteMetric3 Integer32,
ipCidrRouteMetric4 Integer32,
ipCidrRouteMetric5 Integer32,
ipCidrRouteStatus RowStatus
}
ipCidrRouteDest OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The destination IP address of this route.
This object may not take a Multicast (Class D) address
value.
Any assignment (implicit or otherwise) of an instance
of this object to a value x must be rejected if the
bitwise logical-AND of x with the value of the
corresponding instance of the ipCidrRouteMask object is
not equal to x."
::= { ipCidrRouteEntry 1 }
ipCidrRouteMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Indicate the mask to be logical-ANDed with the
destination address before being compared to the value
in the ipCidrRouteDest field. For those systems that
do not support arbitrary subnet masks, an agent
constructs the value of the ipCidrRouteMask by
reference to the IP Address Class.
Any assignment (implicit or otherwise) of an instance
of this object to a value x must be rejected if the
bitwise logical-AND of x with the value of the
corresponding instance of the ipCidrRouteDest object is
not equal to ipCidrRouteDest."
::= { ipCidrRouteEntry 2 }
-- The following convention is included for specification
-- of TOS Field contents. At this time, the Host Requirements
-- and the Router Requirements documents disagree on the width
-- of the TOS field. This mapping describes the Router
-- Requirements mapping, and leaves room to widen the TOS field
-- without impact to fielded systems.
ipCidrRouteTos OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The policy specifier is the IP TOS Field. The encoding
of IP TOS is as specified by the following convention.
Zero indicates the default path if no more specific
policy applies.
+-----+-----+-----+-----+-----+-----+-----+-----+
| | | |
| PRECEDENCE | TYPE OF SERVICE | 0 |
| | | |
+-----+-----+-----+-----+-----+-----+-----+-----+
IP TOS IP TOS
Field Policy Field Policy
Contents Code Contents Code
0 0 0 0 ==> 0 0 0 0 1 ==> 2
0 0 1 0 ==> 4 0 0 1 1 ==> 6
0 1 0 0 ==> 8 0 1 0 1 ==> 10
0 1 1 0 ==> 12 0 1 1 1 ==> 14
1 0 0 0 ==> 16 1 0 0 1 ==> 18
1 0 1 0 ==> 20 1 0 1 1 ==> 22
1 1 0 0 ==> 24 1 1 0 1 ==> 26
1 1 1 0 ==> 28 1 1 1 1 ==> 30"
::= { ipCidrRouteEntry 3 }
ipCidrRouteNextHop OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"On remote routes, the address of the next system en
route; Otherwise, 0.0.0.0."
::= { ipCidrRouteEntry 4 }
ipCidrRouteIfIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The ifIndex value that identifies the local interface
through which the next hop of this route should be
reached."
DEFVAL { 0 }
::= { ipCidrRouteEntry 5 }
ipCidrRouteType OBJECT-TYPE
SYNTAX INTEGER {
other (1), -- not specified by this MIB
reject (2), -- route that discards traffic
local (3), -- local interface
remote (4) -- remote destination
}
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The type of route. Note that local(3) refers to a
route for which the next hop is the final destination;
remote(4) refers to a route for which the next hop is
not the final destination.
Routes that do not result in traffic forwarding or
rejection should not be displayed, even if the
implementation keeps them stored internally.
reject (2) refers to a route that, if matched,
discards the message as unreachable. This is used in
some protocols as a means of correctly aggregating
routes."
::= { ipCidrRouteEntry 6 }
ipCidrRouteProto OBJECT-TYPE
SYNTAX INTEGER {
other (1), -- not specified
local (2), -- local interface
netmgmt (3), -- static route
icmp (4), -- result of ICMP Redirect
-- the following are all dynamic
-- routing protocols
egp (5), -- Exterior Gateway Protocol
ggp (6), -- Gateway-Gateway Protocol
hello (7), -- FuzzBall HelloSpeak
rip (8), -- Berkeley RIP or RIP-II
isIs (9), -- Dual IS-IS
esIs (10), -- ISO 9542
ciscoIgrp (11), -- Cisco IGRP
bbnSpfIgp (12), -- BBN SPF IGP
ospf (13), -- Open Shortest Path First
bgp (14), -- Border Gateway Protocol
idpr (15), -- InterDomain Policy Routing
ciscoEigrp (16) -- Cisco EIGRP
}
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The routing mechanism via which this route was learned.
Inclusion of values for gateway routing protocols is
not intended to imply that hosts should support those
protocols."
::= { ipCidrRouteEntry 7 }
ipCidrRouteAge OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of seconds since this route was last updated
or otherwise determined to be correct. Note that no
semantics of `too old' can be implied, except through
knowledge of the routing protocol by which the route
was learned."
DEFVAL { 0 }
::= { ipCidrRouteEntry 8 }
ipCidrRouteInfo OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"A reference to MIB definitions specific to the
particular routing protocol that is responsible for
this route, as determined by the value specified in the
route's ipCidrRouteProto value. If this information is
not present, its value should be set to the OBJECT
IDENTIFIER { 0 0 }, which is a syntactically valid
object identifier, and any implementation conforming to
ASN.1 and the Basic Encoding Rules must be able to
generate and recognize this value."
::= { ipCidrRouteEntry 9 }
ipCidrRouteNextHopAS OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The Autonomous System Number of the Next Hop. The
semantics of this object are determined by the routing-
protocol specified in the route's ipCidrRouteProto
value. When this object is unknown or not relevant, its
value should be set to zero."
DEFVAL { 0 }
::= { ipCidrRouteEntry 10 }
ipCidrRouteMetric1 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The primary routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's ipCidrRouteProto
value. If this metric is not used, its value should be
set to -1."
DEFVAL { -1 }
::= { ipCidrRouteEntry 11 }
ipCidrRouteMetric2 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's ipCidrRouteProto
value. If this metric is not used, its value should be
set to -1."
DEFVAL { -1 }
::= { ipCidrRouteEntry 12 }
ipCidrRouteMetric3 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's ipCidrRouteProto
value. If this metric is not used, its value should be
set to -1."
DEFVAL { -1 }
::= { ipCidrRouteEntry 13 }
ipCidrRouteMetric4 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's ipCidrRouteProto
value. If this metric is not used, its value should be
set to -1."
DEFVAL { -1 }
::= { ipCidrRouteEntry 14 }
ipCidrRouteMetric5 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's ipCidrRouteProto
value. If this metric is not used, its value should be
set to -1."
DEFVAL { -1 }
::= { ipCidrRouteEntry 15 }
ipCidrRouteStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The row status variable, used according to row
installation and removal conventions."
::= { ipCidrRouteEntry 16 }
-- compliance statements
ipForwardCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for SNMPv2 entities that
implement the ipForward MIB.
This compliance statement has been deprecated and
replaced with ipForwardFullCompliance and
ipForwardReadOnlyCompliance."
MODULE -- this module
MANDATORY-GROUPS { ipForwardCidrRouteGroup }
::= { ipForwardCompliances 1 }
-- units of conformance
ipForwardCidrRouteGroup OBJECT-GROUP
OBJECTS { ipCidrRouteNumber,
ipCidrRouteDest, ipCidrRouteMask, ipCidrRouteTos,
ipCidrRouteNextHop, ipCidrRouteIfIndex,
ipCidrRouteType, ipCidrRouteProto, ipCidrRouteAge,
ipCidrRouteInfo,ipCidrRouteNextHopAS,
ipCidrRouteMetric1, ipCidrRouteMetric2,
ipCidrRouteMetric3, ipCidrRouteMetric4,
ipCidrRouteMetric5, ipCidrRouteStatus
}
STATUS deprecated
DESCRIPTION
"The CIDR Route Table.
This group has been deprecated and replaced with
inetForwardCidrRouteGroup."
::= { ipForwardGroups 3 }
-- Obsoleted Definitions - Objects
ipForwardNumber OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The number of current ipForwardTable entries that are
not invalid."
::= { ipForward 1 }
-- IP Forwarding Table
-- The IP Forwarding Table obsoletes and replaces the ipRoute
-- Table current in MIB-I and MIB-II. It adds knowledge of
-- the autonomous system of the next hop, multiple next hop
-- support, and policy routing support.
ipForwardTable OBJECT-TYPE
SYNTAX SEQUENCE OF IpForwardEntry
MAX-ACCESS not-accessible
STATUS obsolete
DESCRIPTION
"This entity's IP Routing table."
REFERENCE
"RFC 1213 Section 6.6, The IP Group"
::= { ipForward 2 }
ipForwardEntry OBJECT-TYPE
SYNTAX IpForwardEntry
MAX-ACCESS not-accessible
STATUS obsolete
DESCRIPTION
"A particular route to a particular destination, under a
particular policy."
INDEX {
ipForwardDest,
ipForwardProto,
ipForwardPolicy,
ipForwardNextHop
}
::= { ipForwardTable 1 }
IpForwardEntry ::= SEQUENCE {
ipForwardDest IpAddress,
ipForwardMask IpAddress,
ipForwardPolicy Integer32,
ipForwardNextHop IpAddress,
ipForwardIfIndex Integer32,
ipForwardType INTEGER,
ipForwardProto INTEGER,
ipForwardAge Integer32,
ipForwardInfo OBJECT IDENTIFIER,
ipForwardNextHopAS Integer32,
ipForwardMetric1 Integer32,
ipForwardMetric2 Integer32,
ipForwardMetric3 Integer32,
ipForwardMetric4 Integer32,
ipForwardMetric5 Integer32
}
ipForwardDest OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The destination IP address of this route. An entry
with a value of 0.0.0.0 is considered a default route.
This object may not take a Multicast (Class D) address
value.
Any assignment (implicit or otherwise) of an instance
of this object to a value x must be rejected if the
bitwise logical-AND of x with the value of the
corresponding instance of the ipForwardMask object is
not equal to x."
::= { ipForwardEntry 1 }
ipForwardMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS obsolete
DESCRIPTION
"Indicate the mask to be logical-ANDed with the
destination address before being compared to the value
in the ipForwardDest field. For those systems that do
not support arbitrary subnet masks, an agent constructs
the value of the ipForwardMask by reference to the IP
Address Class.
Any assignment (implicit or otherwise) of an instance
of this object to a value x must be rejected if the
bitwise logical-AND of x with the value of the
corresponding instance of the ipForwardDest object is
not equal to ipForwardDest."
DEFVAL { '00000000'H } -- 0.0.0.0
::= { ipForwardEntry 2 }
-- The following convention is included for specification
-- of TOS Field contents. At this time, the Host Requirements
-- and the Router Requirements documents disagree on the width
-- of the TOS field. This mapping describes the Router
-- Requirements mapping, and leaves room to widen the TOS field
-- without impact to fielded systems.
ipForwardPolicy OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The general set of conditions that would cause
the selection of one multipath route (set of
next hops for a given destination) is referred
to as 'policy'.
Unless the mechanism indicated by ipForwardProto
specifies otherwise, the policy specifier is
the IP TOS Field. The encoding of IP TOS is as
specified by the following convention. Zero
indicates the default path if no more specific
policy applies.
+-----+-----+-----+-----+-----+-----+-----+-----+
| | | |
| PRECEDENCE | TYPE OF SERVICE | 0 |
| | | |
+-----+-----+-----+-----+-----+-----+-----+-----+
IP TOS IP TOS
Field Policy Field Policy
Contents Code Contents Code
0 0 0 0 ==> 0 0 0 0 1 ==> 2
0 0 1 0 ==> 4 0 0 1 1 ==> 6
0 1 0 0 ==> 8 0 1 0 1 ==> 10
0 1 1 0 ==> 12 0 1 1 1 ==> 14
1 0 0 0 ==> 16 1 0 0 1 ==> 18
1 0 1 0 ==> 20 1 0 1 1 ==> 22
1 1 0 0 ==> 24 1 1 0 1 ==> 26
1 1 1 0 ==> 28 1 1 1 1 ==> 30
Protocols defining 'policy' otherwise must either
define a set of values that are valid for
this object or must implement an integer-instanced
policy table for which this object's
value acts as an index."
::= { ipForwardEntry 3 }
ipForwardNextHop OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"On remote routes, the address of the next system en
route; otherwise, 0.0.0.0."
::= { ipForwardEntry 4 }
ipForwardIfIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS obsolete
DESCRIPTION
"The ifIndex value that identifies the local interface
through which the next hop of this route should be
reached."
DEFVAL { 0 }
::= { ipForwardEntry 5 }
ipForwardType OBJECT-TYPE
SYNTAX INTEGER {
other (1), -- not specified by this MIB
invalid (2), -- logically deleted
local (3), -- local interface
remote (4) -- remote destination
}
MAX-ACCESS read-create
STATUS obsolete
DESCRIPTION
"The type of route. Note that local(3) refers to a
route for which the next hop is the final destination;
remote(4) refers to a route for which the next hop is
not the final destination.
Setting this object to the value invalid(2) has the
effect of invalidating the corresponding entry in the
ipForwardTable object. That is, it effectively
disassociates the destination identified with said
entry from the route identified with said entry. It is
an implementation-specific matter as to whether the
agent removes an invalidated entry from the table.
Accordingly, management stations must be prepared to
receive tabular information from agents that
corresponds to entries not currently in use. Proper
interpretation of such entries requires examination of
the relevant ipForwardType object."
DEFVAL { invalid }
::= { ipForwardEntry 6 }
ipForwardProto OBJECT-TYPE
SYNTAX INTEGER {
other (1), -- not specified
local (2), -- local interface
netmgmt (3), -- static route
icmp (4), -- result of ICMP Redirect
-- the following are all dynamic
-- routing protocols
egp (5), -- Exterior Gateway Protocol
ggp (6), -- Gateway-Gateway Protocol
hello (7), -- FuzzBall HelloSpeak
rip (8), -- Berkeley RIP or RIP-II
is-is (9), -- Dual IS-IS
es-is (10), -- ISO 9542
ciscoIgrp (11), -- Cisco IGRP
bbnSpfIgp (12), -- BBN SPF IGP
ospf (13), -- Open Shortest Path First
bgp (14), -- Border Gateway Protocol
idpr (15) -- InterDomain Policy Routing
}
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The routing mechanism via which this route was learned.
Inclusion of values for gateway routing protocols is
not intended to imply that hosts should support those
protocols."
::= { ipForwardEntry 7 }
ipForwardAge OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS obsolete
DESCRIPTION
"The number of seconds since this route was last updated
or otherwise determined to be correct. Note that no
semantics of `too old' can be implied except through
knowledge of the routing protocol by which the route
was learned."
DEFVAL { 0 }
::= { ipForwardEntry 8 }
ipForwardInfo OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-create
STATUS obsolete
DESCRIPTION
"A reference to MIB definitions specific to the
particular routing protocol that is responsible for
this route, as determined by the value specified in the
route's ipForwardProto value. If this information is
not present, its value should be set to the OBJECT
IDENTIFIER { 0 0 }, which is a syntactically valid
object identifier, and any implementation conforming to
ASN.1 and the Basic Encoding Rules must be able to
generate and recognize this value."
::= { ipForwardEntry 9 }
ipForwardNextHopAS OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS obsolete
DESCRIPTION
"The Autonomous System Number of the Next Hop. When
this is unknown or not relevant to the protocol
indicated by ipForwardProto, zero."
DEFVAL { 0 }
::= { ipForwardEntry 10 }
ipForwardMetric1 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS obsolete
DESCRIPTION
"The primary routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's ipForwardProto value.
If this metric is not used, its value should be set to
-1."
DEFVAL { -1 }
::= { ipForwardEntry 11 }
ipForwardMetric2 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS obsolete
DESCRIPTION
"An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's ipForwardProto value.
If this metric is not used, its value should be set to
-1."
DEFVAL { -1 }
::= { ipForwardEntry 12 }
ipForwardMetric3 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS obsolete
DESCRIPTION
"An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's ipForwardProto value.
If this metric is not used, its value should be set to
-1."
DEFVAL { -1 }
::= { ipForwardEntry 13 }
ipForwardMetric4 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS obsolete
DESCRIPTION
"An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's ipForwardProto value.
If this metric is not used, its value should be set to
-1."
DEFVAL { -1 }
::= { ipForwardEntry 14 }
ipForwardMetric5 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS obsolete
DESCRIPTION
"An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's ipForwardProto value.
If this metric is not used, its value should be set to
-1."
DEFVAL { -1 }
::= { ipForwardEntry 15 }
-- Obsoleted Definitions - Groups
-- compliance statements
ipForwardOldCompliance MODULE-COMPLIANCE
STATUS obsolete
DESCRIPTION
"The compliance statement for SNMP entities that
implement the ipForward MIB."
MODULE -- this module
MANDATORY-GROUPS { ipForwardMultiPathGroup }
::= { ipForwardCompliances 2 }
ipForwardMultiPathGroup OBJECT-GROUP
OBJECTS { ipForwardNumber,
ipForwardDest, ipForwardMask, ipForwardPolicy,
ipForwardNextHop, ipForwardIfIndex, ipForwardType,
ipForwardProto, ipForwardAge, ipForwardInfo,
ipForwardNextHopAS,
ipForwardMetric1, ipForwardMetric2, ipForwardMetric3,
ipForwardMetric4, ipForwardMetric5
}
STATUS obsolete
DESCRIPTION
"IP Multipath Route Table."
::= { ipForwardGroups 2 }
END