blob: e6f8c6a03e07942ce77fb6f8074b26adfee47b4e [file] [log] [blame]
ChangeLog for hostapd
2015-03-15 - v2.4
* allow OpenSSL cipher configuration to be set for internal EAP server
(openssl_ciphers parameter)
* fixed number of small issues based on hwsim test case failures and
static analyzer reports
* fixed Accounting-Request to not include duplicated Acct-Session-Id
* add support for Acct-Multi-Session-Id in RADIUS Accounting messages
* add support for PMKSA caching with SAE
* add support for generating BSS Load element (bss_load_update_period)
* fixed channel switch from VHT to HT
* add INTERFACE-ENABLED and INTERFACE-DISABLED ctrl_iface events
* add support for learning STA IPv4/IPv6 addresses and configuring
ProxyARP support
* dropped support for the madwifi driver interface
* add support for Suite B (128-bit and 192-bit level) key management and
cipher suites
* fixed a regression with driver=wired
* extend EAPOL-Key msg 1/4 retry workaround for changing SNonce
* add BSS_TM_REQ ctrl_iface command to send BSS Transition Management
Request frames and BSS-TM-RESP event to indicate response to such
frame
* add support for EAP Re-Authentication Protocol (ERP)
* fixed AP IE in EAPOL-Key 3/4 when both WPA and FT was enabled
* fixed a regression in HT 20/40 coex Action frame parsing
* set stdout to be line-buffered
* add support for vendor specific VHT extension to enable 256 QAM rates
(VHT-MCS 8 and 9) on 2.4 GHz band
* RADIUS DAS:
- extend Disconnect-Request processing to allow matching of multiple
sessions
- support Acct-Multi-Session-Id as an identifier
- allow PMKSA cache entry to be removed without association
* expire hostapd STA entry if kernel does not have a matching entry
* allow chanlist to be used to specify a subset of channels for ACS
* improve ACS behavior on 2.4 GHz band and allow channel bias to be
configured with acs_chan_bias parameter
* do not reply to a Probe Request frame that includes DSS Parameter Set
element in which the channel does not match the current operating
channel
* add UPDATE_BEACON ctrl_iface command; this can be used to force Beacon
frame contents to be updated and to start beaconing on an interface
that used start_disabled=1
* fixed some RADIUS server failover cases
2014-10-09 - v2.3
* fixed number of minor issues identified in static analyzer warnings
* fixed DFS and channel switch operation for multi-BSS cases
* started to use constant time comparison for various password and hash
values to reduce possibility of any externally measurable timing
differences
* extended explicit clearing of freed memory and expired keys to avoid
keeping private data in memory longer than necessary
* added support for number of new RADIUS attributes from RFC 7268
(Mobility-Domain-Id, WLAN-HESSID, WLAN-Pairwise-Cipher,
WLAN-Group-Cipher, WLAN-AKM-Suite, WLAN-Group-Mgmt-Pairwise-Cipher)
* fixed GET_CONFIG wpa_pairwise_cipher value
* added code to clear bridge FDB entry on station disconnection
* fixed PMKSA cache timeout from Session-Timeout for WPA/WPA2 cases
* fixed OKC PMKSA cache entry fetch to avoid a possible infinite loop
in case the first entry does not match
* fixed hostapd_cli action script execution to use more robust mechanism
(CVE-2014-3686)
2014-06-04 - v2.2
* fixed SAE confirm-before-commit validation to avoid a potential
segmentation fault in an unexpected message sequence that could be
triggered remotely
* extended VHT support
- Operating Mode Notification
- Power Constraint element (local_pwr_constraint)
- Spectrum management capability (spectrum_mgmt_required=1)
- fix VHT80 segment picking in ACS
- fix vht_capab 'Maximum A-MPDU Length Exponent' handling
- fix VHT20
* fixed HT40 co-ex scan for some pri/sec channel switches
* extended HT40 co-ex support to allow dynamic channel width changes
during the lifetime of the BSS
* fixed HT40 co-ex support to check for overlapping 20 MHz BSS
* fixed MSCHAP UTF-8 to UCS-2 conversion for three-byte encoding;
this fixes password with include UTF-8 characters that use
three-byte encoding EAP methods that use NtPasswordHash
* reverted TLS certificate validation step change in v2.1 that rejected
any AAA server certificate with id-kp-clientAuth even if
id-kp-serverAuth EKU was included
* fixed STA validation step for WPS ER commands to prevent a potential
crash if an ER sends an unexpected PutWLANResponse to a station that
is disassociated, but not fully removed
* enforce full EAP authentication after RADIUS Disconnect-Request by
removing the PMKSA cache entry
* added support for NAS-IP-Address, NAS-identifier, and NAS-IPv6-Address
in RADIUS Disconnect-Request
* added mechanism for removing addresses for MAC ACLs by prefixing an
entry with "-"
* Interworking/Hotspot 2.0 enhancements
- support Hotspot 2.0 Release 2
* OSEN network for online signup connection
* subscription remediation (based on RADIUS server request or
control interface HS20_WNM_NOTIF for testing purposes)
* Hotspot 2.0 release number indication in WFA RADIUS VSA
* deauthentication request (based on RADIUS server request or
control interface WNM_DEAUTH_REQ for testing purposes)
* Session Info URL RADIUS AVP to trigger ESS Disassociation Imminent
* hs20_icon config parameter to configure icon files for OSU
* osu_* config parameters for OSU Providers list
- do not use Interworking filtering rules on Probe Request if
Interworking is disabled to avoid interop issues
* added/fixed nl80211 functionality
- AP interface teardown optimization
- support vendor specific driver command
(VENDOR <vendor id> <sub command id> [<hex formatted data>])
* fixed PMF protection of Deauthentication frame when this is triggered
by session timeout
* internal TLS implementation enhancements/fixes
- add SHA256-based cipher suites
- add DHE-RSA cipher suites
- fix X.509 validation of PKCS#1 signature to check for extra data
* RADIUS server functionality
- add minimal RADIUS accounting server support (hostapd-as-server);
this is mainly to enable testing coverage with hwsim scripts
- allow authentication log to be written into SQLite databse
- added option for TLS protocol testing of an EAP peer by simulating
various misbehaviors/known attacks
- MAC ACL support for testing purposes
* fixed PTK derivation for CCMP-256 and GCMP-256
* extended WPS per-station PSK to support ER case
* added option to configure the management group cipher
(group_mgmt_cipher=AES-128-CMAC (default), BIP-GMAC-128, BIP-GMAC-256,
BIP-CMAC-256)
* fixed AP mode default TXOP Limit values for AC_VI and AC_VO (these
were rounded incorrectly)
* added support for postponing FT response in case PMK-R1 needs to be
pulled from R0KH
* added option to advertise 40 MHz intolerant HT capability with
ht_capab=[40-INTOLERANT]
* remove WPS 1.0 only support, i.e., WSC 2.0 support is now enabled
whenever CONFIG_WPS=y is set
* EAP-pwd fixes
- fix possible segmentation fault on EAP method deinit if an invalid
group is negotiated
* fixed RADIUS client retransmit/failover behavior
- there was a potential ctash due to freed memory being accessed
- failover to a backup server mechanism did not work properly
* fixed a possible crash on double DISABLE command when multiple BSSes
are enabled
* fixed a memory leak in SAE random number generation
* fixed GTK rekeying when the station uses FT protocol
* fixed off-by-one bounds checking in printf_encode()
- this could result in deinial of service in some EAP server cases
* various bug fixes
2014-02-04 - v2.1
* added support for simultaneous authentication of equals (SAE) for
stronger password-based authentication with WPA2-Personal
* added nl80211 functionality
- VHT configuration for nl80211
- support split wiphy dump
- driver-based MAC ACL
- QoS Mapping configuration
* added fully automated regression testing with mac80211_hwsim
* allow ctrl_iface group to be specified on command line (-G<group>)
* allow single hostapd process to control independent WPS interfaces
(wps_independent=1) instead of synchronized operations through all
configured interfaces within a process
* avoid processing received management frames multiple times when using
nl80211 with multiple BSSes
* added support for DFS (processing radar detection events, CAC, channel
re-selection)
* added EAP-EKE server
* added automatic channel selection (ACS)
* added option for using per-BSS (vif) configuration files with
-b<phyname>:<config file name>
* extended global control interface ADD/REMOVE commands to allow BSSes
of a radio to be removed individually without having to add/remove all
other BSSes of the radio at the same time
* added support for sending debug info to Linux tracing (-T on command
line)
* replace dump_file functionality with same information being available
through the hostapd control interface
* added support for using Protected Dual of Public Action frames for
GAS/ANQP exchanges when PMF is enabled
* added support for WPS+NFC updates
- improved protocol
- option to fetch and report alternative carrier records for external
NFC operations
* various bug fixes
2013-01-12 - v2.0
* added AP-STA-DISCONNECTED ctrl_iface event
* improved debug logging (human readable event names, interface name
included in more entries)
* added number of small changes to make it easier for static analyzers
to understand the implementation
* added a workaround for Windows 7 Michael MIC failure reporting and
use of the Secure bit in EAPOL-Key msg 3/4
* fixed number of small bugs (see git logs for more details)
* changed OpenSSL to read full certificate chain from server_cert file
* nl80211: number of updates to use new cfg80211/nl80211 functionality
- replace monitor interface with nl80211 commands
- additional information for driver-based AP SME
* EAP-pwd:
- fix KDF for group 21 and zero-padding
- added support for fragmentation
- increased maximum number of hunting-and-pecking iterations
* avoid excessive Probe Response retries for broadcast Probe Request
frames (only with drivers using hostapd SME/MLME)
* added preliminary support for using TLS v1.2 (CONFIG_TLSV12=y)
* fixed WPS operation stopping on dual concurrent AP
* added wps_rf_bands configuration parameter for overriding RF Bands
value for WPS
* added support for getting per-device PSK from RADIUS Tunnel-Password
* added support for libnl 3.2 and newer
* increased initial group key handshake retransmit timeout to 500 ms
* added a workaround for 4-way handshake to update SNonce even after
having sent EAPOL-Key 3/4 to avoid issues with some supplicant
implementations that can change SNonce for each EAP-Key 2/4
* added a workaround for EAPOL-Key 4/4 using incorrect type value in
WPA2 mode (some deployed stations use WPA type in that message)
* added a WPS workaround for mixed mode AP Settings with Windows 7
* changed WPS AP PIN disabling mechanism to disable the PIN after 10
consecutive failures in addition to using the exponential lockout
period
* added support for WFA Hotspot 2.0
- GAS/ANQP advertisement of network information
- disable_dgaf parameter to disable downstream group-addressed
forwarding
* simplified licensing terms by selecting the BSD license as the only
alternative
* EAP-SIM: fixed re-authentication not to update pseudonym
* EAP-SIM: use Notification round before EAP-Failure
* EAP-AKA: added support for AT_COUNTER_TOO_SMALL
* EAP-AKA: skip AKA/Identity exchange if EAP identity is recognized
* EAP-AKA': fixed identity for MK derivation
* EAP-AKA': updated to RFC 5448 (username prefixes changed); note: this
breaks interoperability with older versions
* EAP-SIM/AKA: allow pseudonym to be used after unknown reauth id
* changed ANonce to be a random number instead of Counter-based
* added support for canceling WPS operations with hostapd_cli wps_cancel
* fixed EAP/WPS to PSK transition on reassociation in cases where
deauthentication is missed
* hlr_auc_gw enhancements:
- a new command line parameter -u can be used to enable updating of
SQN in Milenage file
- use 5 bit IND for SQN updates
- SQLite database can now be used to store Milenage information
* EAP-SIM/AKA DB: added optional use of SQLite database for pseudonyms
and reauth data
* added support for Chargeable-User-Identity (RFC 4372)
* added radius_auth_req_attr and radius_acct_req_attr configuration
parameters to allow adding/overriding of RADIUS attributes in
Access-Request and Accounting-Request packets
* added support for RADIUS dynamic authorization server (RFC 5176)
* added initial support for WNM operations
- BSS max idle period
- WNM-Sleep Mode
* added new WPS NFC ctrl_iface mechanism
- removed obsoleted WPS_OOB command (including support for deprecated
UFD config_method)
* added FT support for drivers that implement MLME internally
* added SA Query support for drivers that implement MLME internally
* removed default ACM=1 from AC_VO and AC_VI
* changed VENDOR-TEST EAP method to use proper private enterprise number
(this will not interoperate with older versions)
* added hostapd.conf parameter vendor_elements to allow arbitrary vendor
specific elements to be added to the Beacon and Probe Response frames
* added support for configuring GCMP cipher for IEEE 802.11ad
* added support for 256-bit AES with internal TLS implementation
* changed EAPOL transmission to use AC_VO if WMM is active
* fixed EAP-TLS/PEAP/TTLS/FAST server to validate TLS Message Length
correctly; invalid messages could have caused the hostapd process to
terminate before this fix [CVE-2012-4445]
* limit number of active wildcard PINs for WPS Registrar to one to avoid
confusing behavior with multiple wildcard PINs
* added a workaround for WPS PBC session overlap detection to avoid
interop issues with deployed station implementations that do not
remove active PBC indication from Probe Request frames properly
* added support for using SQLite for the eap_user database
* added Acct-Session-Id attribute into Access-Request messages
* fixed EAPOL frame transmission to non-QoS STAs with nl80211
(do not send QoS frames if the STA did not negotiate use of QoS for
this association)
2012-05-10 - v1.0
* Add channel selection support in hostapd. See hostapd.conf.
* Add support for IEEE 802.11v Time Advertisement mechanism with UTC
TSF offset. See hostapd.conf for config info.
* Delay STA entry removal until Deauth/Disassoc TX status in AP mode.
This allows the driver to use PS buffering of Deauthentication and
Disassociation frames when the STA is in power save sleep. Only
available with drivers that provide TX status events for Deauth/
Disassoc frames (nl80211).
* Allow PMKSA caching to be disabled on the Authenticator. See
hostap.conf config parameter disable_pmksa_caching.
* atheros: Add support for IEEE 802.11w configuration.
* bsd: Add support for setting HT values in IFM_MMASK.
* Allow client isolation to be configured with ap_isolate. Client
isolation can be used to prevent low-level bridging of frames
between associated stations in the BSS. By default, this bridging
is allowed.
* Allow coexistance of HT BSSes with WEP/TKIP BSSes.
* Add require_ht config parameter, which can be used to configure
hostapd to reject association with any station that does not support
HT PHY.
* Add support for writing debug log to a file using "-f" option. Also
add relog CLI command to re-open the log file.
* Add bridge handling for WDS STA interfaces. By default they are
added to the configured bridge of the AP interface (if present),
but the user can also specify a separate bridge using cli command
wds_bridge.
* hostapd_cli:
- Add wds_bridge command for specifying bridge for WDS STA
interfaces.
- Add relog command for reopening log file.
- Send AP-STA-DISCONNECTED event when an AP disconnects a station
due to inactivity.
- Add wps_config ctrl_interface command for configuring AP. This
command can be used to configure the AP using the internal WPS
registrar. It works in the same way as new AP settings received
from an ER.
- Many WPS/WPS ER commands - see WPS/WPS ER sections for details.
- Add command get version, that returns hostapd version string.
* WNM: Add BSS Transition Management Request for ESS Disassoc Imminent.
Use hostapd_cli ess_disassoc (STA addr) (URL) to send the
notification to the STA.
* Allow AP mode to disconnect STAs based on low ACK condition (when
the data connection is not working properly, e.g., due to the STA
going outside the range of the AP). Disabled by default, enable by
config option disassoc_low_ack.
* Add WPA_IGNORE_CONFIG_ERRORS build option to continue in case of bad
config file.
* WPS:
- Send AP Settings as a wrapped Credential attribute to ctrl_iface
in WPS-NEW-AP-SETTINGS.
- Dispatch more WPS events through hostapd ctrl_iface.
- Add mechanism for indicating non-standard WPS errors.
- Change concurrent radio AP to use only one WPS UPnP instance.
- Add wps_check_pin command for processing PIN from user input.
UIs can use this command to process a PIN entered by a user and to
validate the checksum digit (if present).
- Add hostap_cli get_config command to display current AP config.
- Add new hostapd_cli command, wps_ap_pin, to manage AP PIN at
runtime and support dynamic AP PIN management.
- Disable AP PIN after 10 consecutive failures. Slow down attacks
on failures up to 10.
- Allow AP to start in Enrollee mode without AP PIN for probing,
to be compatible with Windows 7.
- Add Config Error into WPS-FAIL events to provide more info
to the user on how to resolve the issue.
- When controlling multiple interfaces:
- apply WPS commands to all interfaces configured to use WPS
- apply WPS config changes to all interfaces that use WPS
- when an attack is detected on any interface, disable AP PIN on
all interfaces
* WPS ER:
- Show SetSelectedRegistrar events as ctrl_iface events.
- Add special AP Setup Locked mode to allow read only ER.
ap_setup_locked=2 can now be used to enable a special mode where
WPS ER can learn the current AP settings, but cannot change them.
* WPS 2.0: Add support for WPS 2.0 (CONFIG_WPS2)
- Add build option CONFIG_WPS_EXTENSIBILITY_TESTING to enable tool
for testing protocol extensibility.
- Add build option CONFIG_WPS_STRICT to allow disabling of WPS
workarounds.
- Add support for AuthorizedMACs attribute.
* TDLS:
- Allow TDLS use or TDLS channel switching in the BSS to be
prohibited in the BSS, using config params tdls_prohibit and
tdls_prohibit_chan_switch.
* EAP server: Add support for configuring fragment size (see
fragment_size in hostapd.conf).
* wlantest: Add a tool wlantest for IEEE802.11 protocol testing.
wlantest can be used to capture frames from a monitor interface
for realtime capturing or from pcap files for offline analysis.
* Interworking: Support added for 802.11u. Enable in .config with
CONFIG_INTERWORKING. See hostapd.conf for config parameters for
interworking.
* Android: Add build and runtime support for Android hostapd.
* Add a new debug message level for excessive information. Use
-ddd to enable.
* TLS: Add support for tls_disable_time_checks=1 in client mode.
* Internal TLS:
- Add support for TLS v1.1 (RFC 4346). Enable with build parameter
CONFIG_TLSV11.
- Add domainComponent parser for X.509 names
* Reorder some IEs to get closer to IEEE 802.11 standard. Move
WMM into end of Beacon, Probe Resp and (Re)Assoc Resp frames.
Move HT IEs to be later in (Re)Assoc Resp.
* Many bugfixes.
2010-04-18 - v0.7.2
* fix WPS internal Registrar use when an external Registrar is also
active
* bsd: Cleaned up driver wrapper and added various low-level
configuration options
* TNC: fixed issues with fragmentation
* EAP-TNC: add Flags field into fragment acknowledgement (needed to
interoperate with other implementations; may potentially breaks
compatibility with older wpa_supplicant/hostapd versions)
* cleaned up driver wrapper API for multi-BSS operations
* nl80211: fix multi-BSS and VLAN operations
* fix number of issues with IEEE 802.11r/FT; this version is not
backwards compatible with old versions
* add SA Query Request processing in AP mode (IEEE 802.11w)
* fix IGTK PN in group rekeying (IEEE 802.11w)
* fix WPS PBC session overlap detection to use correct attribute
* hostapd_notif_Assoc() can now be called with all IEs to simplify
driver wrappers
* work around interoperability issue with some WPS External Registrar
implementations
* nl80211: fix WPS IE update
* hostapd_cli: add support for action script operations (run a script
on hostapd events)
* fix DH padding with internal crypto code (mainly, for WPS)
* fix WPS association with both WPS IE and WPA/RSN IE present with
driver wrappers that use hostapd MLME (e.g., nl80211)
2010-01-16 - v0.7.1
* cleaned up driver wrapper API (struct wpa_driver_ops); the new API
is not fully backwards compatible, so out-of-tree driver wrappers
will need modifications
* cleaned up various module interfaces
* merge hostapd and wpa_supplicant developers' documentation into a
single document
* fixed HT Capabilities IE with nl80211 drivers
* moved generic AP functionality code into src/ap
* WPS: handle Selected Registrar as union of info from all Registrars
* remove obsolte Prism54.org driver wrapper
* added internal debugging mechanism with backtrace support and memory
allocation/freeing validation, etc. tests (CONFIG_WPA_TRACE=y)
* EAP-FAST server: piggyback Phase 2 start with the end of Phase 1
* WPS: add support for dynamically selecting whether to provision the
PSK as an ASCII passphrase or PSK
* added support for WDS (4-address frame) mode with per-station virtual
interfaces (wds_sta=1 in config file; only supported with
driver=nl80211 for now)
* fixed WPS Probe Request processing to handle missing required
attribute
* fixed PKCS#12 use with OpenSSL 1.0.0
* detect bridge interface automatically so that bridge parameter in
hostapd.conf becomes optional (though, it may now be used to
automatically add then WLAN interface into a bridge with
driver=nl80211)
2009-11-21 - v0.7.0
* increased hostapd_cli ping interval to 5 seconds and made this
configurable with a new command line options (-G<seconds>)
* driver_nl80211: use Linux socket filter to improve performance
* added support for external Registrars with WPS (UPnP transport)
* 802.11n: scan for overlapping BSSes before starting 20/40 MHz channel
* driver_nl80211: fixed STA accounting data collection (TX/RX bytes
reported correctly; TX/RX packets not yet available from kernel)
* added support for WPS USBA out-of-band mechanism with USB Flash
Drives (UFD) (CONFIG_WPS_UFD=y)
* fixed EAPOL/EAP reauthentication when using an external RADIUS
authentication server
* fixed TNC with EAP-TTLS
* fixed IEEE 802.11r key derivation function to match with the standard
(note: this breaks interoperability with previous version) [Bug 303]
* fixed SHA-256 based key derivation function to match with the
standard when using CCMP (for IEEE 802.11r and IEEE 802.11w)
(note: this breaks interoperability with previous version) [Bug 307]
* added number of code size optimizations to remove unnecessary
functionality from the program binary based on build configuration
(part of this automatic; part configurable with CONFIG_NO_* build
options)
* use shared driver wrapper files with wpa_supplicant
* driver_nl80211: multiple updates to provide support for new Linux
nl80211/mac80211 functionality
* updated management frame protection to use IEEE Std 802.11w-2009
* fixed number of small WPS issues and added workarounds to
interoperate with common deployed broken implementations
* added some IEEE 802.11n co-existence rules to disable 40 MHz channels
or modify primary/secondary channels if needed based on neighboring
networks
* added support for NFC out-of-band mechanism with WPS
* added preliminary support for IEEE 802.11r RIC processing
2009-01-06 - v0.6.7
* added support for Wi-Fi Protected Setup (WPS)
(hostapd can now be configured to act as an integrated WPS Registrar
and provision credentials for WPS Enrollees using PIN and PBC
methods; external wireless Registrar can configure the AP, but
external WLAN Manager Registrars are not supported); WPS support can
be enabled by adding CONFIG_WPS=y into .config and setting the
runtime configuration variables in hostapd.conf (see WPS section in
the example configuration file); new hostapd_cli commands wps_pin and
wps_pbc are used to configure WPS negotiation; see README-WPS for
more details
* added IEEE 802.11n HT capability configuration (ht_capab)
* added support for generating Country IE based on nl80211 regulatory
information (added if ieee80211d=1 in configuration)
* fixed WEP authentication (both Open System and Shared Key) with
mac80211
* added support for EAP-AKA' (draft-arkko-eap-aka-kdf)
* added support for using driver_test over UDP socket
* changed EAP-GPSK to use the IANA assigned EAP method type 51
* updated management frame protection to use IEEE 802.11w/D7.0
* fixed retransmission of EAP requests if no response is received
2008-11-23 - v0.6.6
* added a new configuration option, wpa_ptk_rekey, that can be used to
enforce frequent PTK rekeying, e.g., to mitigate some attacks against
TKIP deficiencies
* updated OpenSSL code for EAP-FAST to use an updated version of the
session ticket overriding API that was included into the upstream
OpenSSL 0.9.9 tree on 2008-11-15 (no additional OpenSSL patch is
needed with that version anymore)
* changed channel flags configuration to read the information from
the driver (e.g., via driver_nl80211 when using mac80211) instead of
using hostapd as the source of the regulatory information (i.e.,
information from CRDA is now used with mac80211); this allows 5 GHz
channels to be used with hostapd (if allowed in the current
regulatory domain)
* fixed EAP-TLS message processing for the last TLS message if it is
large enough to require fragmentation (e.g., if a large Session
Ticket data is included)
* fixed listen interval configuration for nl80211 drivers
2008-11-01 - v0.6.5
* added support for SHA-256 as X.509 certificate digest when using the
internal X.509/TLSv1 implementation
* fixed EAP-FAST PAC-Opaque padding (0.6.4 broke this for some peer
identity lengths)
* fixed internal TLSv1 implementation for abbreviated handshake (used
by EAP-FAST server)
* added support for setting VLAN ID for STAs based on local MAC ACL
(accept_mac_file) as an alternative for RADIUS server-based
configuration
* updated management frame protection to use IEEE 802.11w/D6.0
(adds a new association ping to protect against unauthenticated
authenticate or (re)associate request frames dropping association)
* added support for using SHA256-based stronger key derivation for WPA2
(IEEE 802.11w)
* added new "driver wrapper" for RADIUS-only configuration
(driver=none in hostapd.conf; CONFIG_DRIVER_NONE=y in .config)
* fixed WPA/RSN IE validation to verify that the proto (WPA vs. WPA2)
is enabled in configuration
* changed EAP-FAST configuration to use separate fields for A-ID and
A-ID-Info (eap_fast_a_id_info) to allow A-ID to be set to a fixed
16-octet len binary value for better interoperability with some peer
implementations; eap_fast_a_id is now configured as a hex string
* driver_nl80211: Updated to match the current Linux mac80211 AP mode
configuration (wireless-testing.git and Linux kernel releases
starting from 2.6.29)
2008-08-10 - v0.6.4
* added peer identity into EAP-FAST PAC-Opaque and skip Phase 2
Identity Request if identity is already known
* added support for EAP Sequences in EAP-FAST Phase 2
* added support for EAP-TNC (Trusted Network Connect)
(this version implements the EAP-TNC method and EAP-TTLS/EAP-FAST
changes needed to run two methods in sequence (IF-T) and the IF-IMV
and IF-TNCCS interfaces from TNCS)
* added support for optional cryptobinding with PEAPv0
* added fragmentation support for EAP-TNC
* added support for fragmenting EAP-TTLS/PEAP/FAST Phase 2 (tunneled)
data
* added support for opportunistic key caching (OKC)
2008-02-22 - v0.6.3
* fixed Reassociation Response callback processing when using internal
MLME (driver_{hostap,nl80211,test}.c)
* updated FT support to use the latest draft, IEEE 802.11r/D9.0
* copy optional Proxy-State attributes into RADIUS response when acting
as a RADIUS authentication server
* fixed EAPOL state machine to handle a case in which no response is
received from the RADIUS authentication server; previous version
could have triggered a crash in some cases after a timeout
* fixed EAP-SIM/AKA realm processing to allow decorated usernames to
be used
* added a workaround for EAP-SIM/AKA peers that include incorrect null
termination in the username
* fixed EAP-SIM/AKA protected result indication to include AT_COUNTER
attribute in notification messages only when using fast
reauthentication
* fixed EAP-SIM Start response processing for fast reauthentication
case
* added support for pending EAP processing in EAP-{PEAP,TTLS,FAST}
phase 2 to allow EAP-SIM and EAP-AKA to be used as the Phase 2 method
2008-01-01 - v0.6.2
* fixed EAP-SIM and EAP-AKA message parser to validate attribute
lengths properly to avoid potential crash caused by invalid messages
* added data structure for storing allocated buffers (struct wpabuf);
this does not affect hostapd usage, but many of the APIs changed
and various interfaces (e.g., EAP) is not compatible with old
versions
* added support for protecting EAP-AKA/Identity messages with
AT_CHECKCODE (optional feature in RFC 4187)
* added support for protected result indication with AT_RESULT_IND for
EAP-SIM and EAP-AKA (eap_sim_aka_result_ind=1)
* added support for configuring EAP-TTLS phase 2 non-EAP methods in
EAP server configuration; previously all four were enabled for every
phase 2 user, now all four are disabled by default and need to be
enabled with new method names TTLS-PAP, TTLS-CHAP, TTLS-MSCHAP,
TTLS-MSCHAPV2
* removed old debug printing mechanism and the related 'debug'
parameter in the configuration file; debug verbosity is now set with
-d (or -dd) command line arguments
* added support for EAP-IKEv2 (draft-tschofenig-eap-ikev2-15.txt);
only shared key/password authentication is supported in this version
2007-11-24 - v0.6.1
* added experimental, integrated TLSv1 server implementation with the
needed X.509/ASN.1/RSA/bignum processing (this can be enabled by
setting CONFIG_TLS=internal and CONFIG_INTERNAL_LIBTOMMATH=y in
.config); this can be useful, e.g., if the target system does not
have a suitable TLS library and a minimal code size is required
* added support for EAP-FAST server method to the integrated EAP
server
* updated EAP Generalized Pre-Shared Key (EAP-GPSK) to use the latest
draft (draft-ietf-emu-eap-gpsk-07.txt)
* added a new configuration parameter, rsn_pairwise, to allow different
pairwise cipher suites to be enabled for WPA and RSN/WPA2
(note: if wpa_pairwise differs from rsn_pairwise, the driver will
either need to support this or will have to use the WPA/RSN IEs from
hostapd; currently, the included madwifi and bsd driver interfaces do
not have support for this)
* updated FT support to use the latest draft, IEEE 802.11r/D8.0
2007-05-28 - v0.6.0
* added experimental IEEE 802.11r/D6.0 support
* updated EAP-SAKE to RFC 4763 and the IANA-allocated EAP type 48
* updated EAP-PSK to use the IANA-allocated EAP type 47
* fixed EAP-PSK bit ordering of the Flags field
* fixed configuration reloading (SIGHUP) to re-initialize WPA PSKs
by reading wpa_psk_file [Bug 181]
* fixed EAP-TTLS AVP parser processing for too short AVP lengths
* fixed IPv6 connection to RADIUS accounting server
* updated EAP Generalized Pre-Shared Key (EAP-GPSK) to use the latest
draft (draft-ietf-emu-eap-gpsk-04.txt)
* hlr_auc_gw: read GSM triplet file into memory and rotate through the
entries instead of only using the same three triplets every time
(this does not work properly with tests using multiple clients, but
provides bit better triplet data for testing a single client; anyway,
if a better quality triplets are needed, GSM-Milenage should be used
instead of hardcoded triplet file)
* fixed EAP-MSCHAPv2 server to use a space between S and M parameters
in Success Request [Bug 203]
* added support for sending EAP-AKA Notifications in error cases
* updated to use IEEE 802.11w/D2.0 for management frame protection
(still experimental)
* RADIUS server: added support for processing duplicate messages
(retransmissions from RADIUS client) by replying with the previous
reply
2006-11-24 - v0.5.6
* added support for configuring and controlling multiple BSSes per
radio interface (bss=<ifname> in hostapd.conf); this is only
available with Devicescape and test driver interfaces
* fixed PMKSA cache update in the end of successful RSN
pre-authentication
* added support for dynamic VLAN configuration (i.e., selecting VLAN-ID
for each STA based on RADIUS Access-Accept attributes); this requires
VLAN support from the kernel driver/802.11 stack and this is
currently only available with Devicescape and test driver interfaces
* driver_madwifi: fixed configuration of unencrypted modes (plaintext
and IEEE 802.1X without WEP)
* removed STAKey handshake since PeerKey handshake has replaced it in
IEEE 802.11ma and there are no known deployments of STAKey
* updated EAP Generalized Pre-Shared Key (EAP-GPSK) to use the latest
draft (draft-ietf-emu-eap-gpsk-01.txt)
* added preliminary implementation of IEEE 802.11w/D1.0 (management
frame protection)
(Note: this requires driver support to work properly.)
(Note2: IEEE 802.11w is an unapproved draft and subject to change.)
* hlr_auc_gw: added support for GSM-Milenage (for EAP-SIM)
* hlr_auc_gw: added support for reading per-IMSI Milenage keys and
parameters from a text file to make it possible to implement proper
GSM/UMTS authentication server for multiple SIM/USIM cards using
EAP-SIM/EAP-AKA
* fixed session timeout processing with drivers that do not use
ieee802_11.c (e.g., madwifi)
2006-08-27 - v0.5.5
* added 'hostapd_cli new_sta <addr>' command for adding a new STA into
hostapd (e.g., to initialize wired network authentication based on an
external signal)
* fixed hostapd to add PMKID KDE into 4-Way Handshake Message 1 when
using WPA2 even if PMKSA caching is not used
* added -P<pid file> argument for hostapd to write the current process
id into a file
* added support for RADIUS Authentication Server MIB (RFC 2619)
2006-06-20 - v0.5.4
* fixed nt_password_hash build [Bug 144]
* added PeerKey handshake implementation for IEEE 802.11e
direct link setup (DLS) to replace STAKey handshake
* added support for EAP Generalized Pre-Shared Key (EAP-GPSK,
draft-clancy-emu-eap-shared-secret-00.txt)
* fixed a segmentation fault when RSN pre-authentication was completed
successfully [Bug 152]
2006-04-27 - v0.5.3
* do not build nt_password_hash and hlr_auc_gw by default to avoid
requiring a TLS library for a successful build; these programs can be
build with 'make nt_password_hash' and 'make hlr_auc_gw'
* added a new configuration option, eapol_version, that can be used to
set EAPOL version to 1 (default is 2) to work around broken client
implementations that drop EAPOL frames which use version number 2
[Bug 89]
* added support for EAP-SAKE (no EAP method number allocated yet, so
this is using the same experimental type 255 as EAP-PSK)
* fixed EAP-MSCHAPv2 message length validation
2006-03-19 - v0.5.2
* fixed stdarg use in hostapd_logger(): if both stdout and syslog
logging was enabled, hostapd could trigger a segmentation fault in
vsyslog on some CPU -- C library combinations
* moved HLR/AuC gateway implementation for EAP-SIM/AKA into an external
program to make it easier to use for implementing real SS7 gateway;
eap_sim_db is not anymore used as a file name for GSM authentication
triplets; instead, it is path to UNIX domain socket that will be used
to communicate with the external gateway program (e.g., hlr_auc_gw)
* added example HLR/AuC gateway implementation, hlr_auc_gw, that uses
local information (GSM authentication triplets from a text file and
hardcoded AKA authentication data); this can be used to test EAP-SIM
and EAP-AKA
* added Milenage algorithm (example 3GPP AKA algorithm) to hlr_auc_gw
to make it possible to test EAP-AKA with real USIM cards (this is
disabled by default; define AKA_USE_MILENAGE when building hlr_auc_gw
to enable this)
* driver_madwifi: added support for getting station RSN IE from
madwifi-ng svn r1453 and newer; this fixes RSN that was apparently
broken with earlier change (r1357) in the driver
* changed EAP method registration to use a dynamic list of methods
instead of a static list generated at build time
* fixed WPA message 3/4 not to encrypt Key Data field (WPA IE)
[Bug 125]
* added ap_max_inactivity configuration parameter
2006-01-29 - v0.5.1
* driver_test: added better support for multiple APs and STAs by using
a directory with sockets that include MAC address for each device in
the name (test_socket=DIR:/tmp/test)
* added support for EAP expanded type (vendor specific EAP methods)
2005-12-18 - v0.5.0 (beginning of 0.5.x development releases)
* added experimental STAKey handshake implementation for IEEE 802.11e
direct link setup (DLS); note: this is disabled by default in both
build and runtime configuration (can be enabled with CONFIG_STAKEY=y
and stakey=1)
* added support for EAP methods to use callbacks to external programs
by buffering a pending request and processing it after the EAP method
is ready to continue
* improved EAP-SIM database interface to allow external request to GSM
HLR/AuC without blocking hostapd process
* added support for using EAP-SIM pseudonyms and fast re-authentication
* added support for EAP-AKA in the integrated EAP authenticator
* added support for matching EAP identity prefixes (e.g., "1"*) in EAP
user database to allow EAP-SIM/AKA selection without extra roundtrip
for EAP-Nak negotiation
* added support for storing EAP user password as NtPasswordHash instead
of plaintext password when using MSCHAP or MSCHAPv2 for
authentication (hash:<16-octet hex value>); added nt_password_hash
tool for hashing password to generate NtPasswordHash
2005-11-20 - v0.4.7 (beginning of 0.4.x stable releases)
* driver_wired: fixed EAPOL sending to optionally use PAE group address
as the destination instead of supplicant MAC address; this is
disabled by default, but should be enabled with use_pae_group_addr=1
in configuration file if the wired interface is used by only one
device at the time (common switch configuration)
* driver_madwifi: configure driver to use TKIP countermeasures in order
to get correct behavior (IEEE 802.11 association failing; previously,
association succeeded, but hostpad forced disassociation immediately)
* driver_madwifi: added support for madwifi-ng
2005-10-27 - v0.4.6
* added support for replacing user identity from EAP with RADIUS
User-Name attribute from Access-Accept message, if that is included,
for the RADIUS accounting messages (e.g., for EAP-PEAP/TTLS to get
tunneled identity into accounting messages when the RADIUS server
does not support better way of doing this with Class attribute)
* driver_madwifi: fixed EAPOL packet receive for configuration where
ath# is part of a bridge interface
* added a configuration file and log analyzer script for logwatch
* fixed EAPOL state machine step function to process all state
transitions before processing new events; this resolves a race
condition in which EAPOL-Start message could trigger hostapd to send
two EAP-Response/Identity frames to the authentication server
2005-09-25 - v0.4.5
* added client CA list to the TLS certificate request in order to make
it easier for the client to select which certificate to use
* added experimental support for EAP-PSK
* added support for WE-19 (hostap, madwifi)
2005-08-21 - v0.4.4
* fixed build without CONFIG_RSN_PREAUTH
* fixed FreeBSD build
2005-06-26 - v0.4.3
* fixed PMKSA caching to copy User-Name and Class attributes so that
RADIUS accounting gets correct information
* start RADIUS accounting only after successful completion of WPA
4-Way Handshake if WPA-PSK is used
* fixed PMKSA caching for the case where STA (re)associates without
first disassociating
2005-06-12 - v0.4.2
* EAP-PAX is now registered as EAP type 46
* fixed EAP-PAX MAC calculation
* fixed EAP-PAX CK and ICK key derivation
* renamed eap_authenticator configuration variable to eap_server to
better match with RFC 3748 (EAP) terminology
* driver_test: added support for testing hostapd with wpa_supplicant
by using test driver interface without any kernel drivers or network
cards
2005-05-22 - v0.4.1
* fixed RADIUS server initialization when only auth or acct server
is configured and the other one is left empty
* driver_madwifi: added support for RADIUS accounting
* driver_madwifi: added preliminary support for compiling against 'BSD'
branch of madwifi CVS tree
* driver_madwifi: fixed pairwise key removal to allow WPA reauth
without disassociation
* added support for reading additional certificates from PKCS#12 files
and adding them to the certificate chain
* fixed RADIUS Class attribute processing to only use Access-Accept
packets to update Class; previously, other RADIUS authentication
packets could have cleared Class attribute
* added support for more than one Class attribute in RADIUS packets
* added support for verifying certificate revocation list (CRL) when
using integrated EAP authenticator for EAP-TLS; new hostapd.conf
options 'check_crl'; CRL must be included in the ca_cert file for now
2005-04-25 - v0.4.0 (beginning of 0.4.x development releases)
* added support for including network information into
EAP-Request/Identity message (ASCII-0 (nul) in eap_message)
(e.g., to implement draft-adrange-eap-network-discovery-07.txt)
* fixed a bug which caused some RSN pre-authentication cases to use
freed memory and potentially crash hostapd
* fixed private key loading for cases where passphrase is not set
* added support for sending TLS alerts and aborting authentication
when receiving a TLS alert
* fixed WPA2 to add PMKSA cache entry when using integrated EAP
authenticator
* fixed PMKSA caching (EAP authentication was not skipped correctly
with the new state machine changes from IEEE 802.1X draft)
* added support for RADIUS over IPv6; own_ip_addr, auth_server_addr,
and acct_server_addr can now be IPv6 addresses (CONFIG_IPV6=y needs
to be added to .config to include IPv6 support); for RADIUS server,
radius_server_ipv6=1 needs to be set in hostapd.conf and addresses
in RADIUS clients file can then use IPv6 format
* added experimental support for EAP-PAX
* replaced hostapd control interface library (hostapd_ctrl.[ch]) with
the same implementation that wpa_supplicant is using (wpa_ctrl.[ch])
2005-02-12 - v0.3.7 (beginning of 0.3.x stable releases)
2005-01-23 - v0.3.5
* added support for configuring a forced PEAP version based on the
Phase 1 identity
* fixed PEAPv1 to use tunneled EAP-Success/Failure instead of EAP-TLV
to terminate authentication
* fixed EAP identifier duplicate processing with the new IEEE 802.1X
draft
* clear accounting data in the driver when starting a new accounting
session
* driver_madwifi: filter wireless events based on ifindex to allow more
than one network interface to be used
* fixed WPA message 2/4 processing not to cancel timeout for TimeoutEvt
setting if the packet does not pass MIC verification (e.g., due to
incorrect PSK); previously, message 1/4 was not tried again if an
invalid message 2/4 was received
* fixed reconfiguration of RADIUS client retransmission timer when
adding a new message to the pending list; previously, timer was not
updated at this point and if there was a pending message with long
time for the next retry, the new message needed to wait that long for
its first retry, too
2005-01-09 - v0.3.4
* added support for configuring multiple allowed EAP types for Phase 2
authentication (EAP-PEAP, EAP-TTLS)
* fixed EAPOL-Start processing to trigger WPA reauthentication
(previously, only EAPOL authentication was done)
2005-01-02 - v0.3.3
* added support for EAP-PEAP in the integrated EAP authenticator
* added support for EAP-GTC in the integrated EAP authenticator
* added support for configuring list of EAP methods for Phase 1 so that
the integrated EAP authenticator can, e.g., use the wildcard entry
for EAP-TLS and EAP-PEAP
* added support for EAP-TTLS in the integrated EAP authenticator
* added support for EAP-SIM in the integrated EAP authenticator
* added support for using hostapd as a RADIUS authentication server
with the integrated EAP authenticator taking care of EAP
authentication (new hostapd.conf options: radius_server_clients and
radius_server_auth_port); this is not included in default build; use
CONFIG_RADIUS_SERVER=y in .config to include
2004-12-19 - v0.3.2
* removed 'daemonize' configuration file option since it has not really
been used at all for more than year
* driver_madwifi: fixed group key setup and added get_ssid method
* added support for EAP-MSCHAPv2 in the integrated EAP authenticator
2004-12-12 - v0.3.1
* added support for integrated EAP-TLS authentication (new hostapd.conf
variables: ca_cert, server_cert, private_key, private_key_passwd);
this enabled dynamic keying (WPA2/WPA/IEEE 802.1X/WEP) without
external RADIUS server
* added support for reading PKCS#12 (PFX) files (as a replacement for
PEM/DER) to get certificate and private key (CONFIG_PKCS12)
2004-12-05 - v0.3.0 (beginning of 0.3.x development releases)
* added support for Acct-{Input,Output}-Gigawords
* added support for Event-Timestamp (in RADIUS Accounting-Requests)
* added support for RADIUS Authentication Client MIB (RFC2618)
* added support for RADIUS Accounting Client MIB (RFC2620)
* made EAP re-authentication period configurable (eap_reauth_period)
* fixed EAPOL reauthentication to trigger WPA/WPA2 reauthentication
* fixed EAPOL state machine to stop if STA is removed during
eapol_sm_step(); this fixes at least one segfault triggering bug with
IEEE 802.11i pre-authentication
* added support for multiple WPA pre-shared keys (e.g., one for each
client MAC address or keys shared by a group of clients);
new hostapd.conf field wpa_psk_file for setting path to a text file
containing PSKs, see hostapd.wpa_psk for an example
* added support for multiple driver interfaces to allow hostapd to be
used with other drivers
* added wired authenticator driver interface (driver=wired in
hostapd.conf, see wired.conf for example configuration)
* added madwifi driver interface (driver=madwifi in hostapd.conf, see
madwifi.conf for example configuration; Note: include files from
madwifi project is needed for building and a configuration file,
.config, needs to be created in hostapd directory with
CONFIG_DRIVER_MADWIFI=y to include this driver interface in hostapd
build)
* fixed an alignment issue that could cause SHA-1 to fail on some
platforms (e.g., Intel ixp425 with a compiler that does not 32-bit
align variables)
* fixed RADIUS reconnection after an error in sending interim
accounting packets
* added hostapd control interface for external programs and an example
CLI, hostapd_cli (like wpa_cli for wpa_supplicant)
* started adding dot11, dot1x, radius MIBs ('hostapd_cli mib',
'hostapd_cli sta <addr>')
* finished update from IEEE 802.1X-2001 to IEEE 802.1X-REV (now d11)
* added support for strict GTK rekeying (wpa_strict_rekey in
hostapd.conf)
* updated IAPP to use UDP port 3517 and multicast address 224.0.1.178
(instead of broadcast) for IAPP ADD-notify (moved from draft 3 to
IEEE 802.11F-2003)
* added Prism54 driver interface (driver=prism54 in hostapd.conf;
note: .config needs to be created in hostapd directory with
CONFIG_DRIVER_PRISM54=y to include this driver interface in hostapd
build)
* dual-licensed hostapd (GPLv2 and BSD licenses)
* fixed RADIUS accounting to generate a new session id for cases where
a station reassociates without first being complete deauthenticated
* fixed STA disassociation handler to mark next timeout state to
deauthenticate the station, i.e., skip long wait for inactivity poll
and extra disassociation, if the STA disassociates without
deauthenticating
* added integrated EAP authenticator that can be used instead of
external RADIUS authentication server; currently, only EAP-MD5 is
supported, so this cannot yet be used for key distribution; the EAP
method interface is generic, though, so adding new EAP methods should
be straightforward; new hostapd.conf variables: 'eap_authenticator'
and 'eap_user_file'; this obsoletes "minimal authentication server"
('minimal_eap' in hostapd.conf) which is now removed
* added support for FreeBSD and driver interface for the BSD net80211
layer (driver=bsd in hostapd.conf and CONFIG_DRIVER_BSD=y in
.config); please note that some of the required kernel mods have not
yet been committed
2004-07-17 - v0.2.4 (beginning of 0.2.x stable releases)
* fixed some accounting cases where Accounting-Start was sent when
IEEE 802.1X port was being deauthorized
2004-06-20 - v0.2.3
* modified RADIUS client to re-connect the socket in case of certain
error codes that are generated when a network interface state is
changes (e.g., when IP address changes or the interface is set UP)
* fixed couple of cases where EAPOL state for a station was freed
twice causing a segfault for hostapd
* fixed couple of bugs in processing WPA deauthentication (freed data
was used)
2004-05-31 - v0.2.2
* fixed WPA/WPA2 group rekeying to use key index correctly (GN/GM)
* fixed group rekeying to send zero TSC in EAPOL-Key messages to fix
cases where STAs dropped multicast frames as replay attacks
* added support for copying RADIUS Attribute 'Class' from
authentication messages into accounting messages
* send canned EAP failure if RADIUS server sends Access-Reject without
EAP message (previously, Supplicant was not notified in this case)
* fixed mixed WPA-PSK and WPA-EAP mode to work with WPA-PSK (i.e., do
not start EAPOL state machines if the STA selected to use WPA-PSK)
2004-05-06 - v0.2.1
* added WPA and IEEE 802.11i/RSN (WPA2) Authenticator functionality
- based on IEEE 802.11i/D10.0 but modified to interoperate with WPA
(i.e., IEEE 802.11i/D3.0)
- supports WPA-only, RSN-only, and mixed WPA/RSN mode
- both WPA-PSK and WPA-RADIUS/EAP are supported
- PMKSA caching and pre-authentication
- new hostapd.conf variables: wpa, wpa_psk, wpa_passphrase,
wpa_key_mgmt, wpa_pairwise, wpa_group_rekey, wpa_gmk_rekey,
rsn_preauth, rsn_preauth_interfaces
* fixed interim accounting to remove any pending accounting messages
to the STA before sending a new one
2004-02-15 - v0.2.0
* added support for Acct-Interim-Interval:
- draft-ietf-radius-acct-interim-01.txt
- use Acct-Interim-Interval attribute from Access-Accept if local
'radius_acct_interim_interval' is not set
- allow different update intervals for each STA
* fixed event loop to call signal handlers only after returning from
the real signal handler
* reset sta->timeout_next after successful association to make sure
that the previously registered inactivity timer will not remove the
STA immediately (e.g., if STA deauthenticates and re-associates
before the timer is triggered).
* added new hostapd.conf variable, nas_identifier, that can be used to
add an optional RADIUS Attribute, NAS-Identifier, into authentication
and accounting messages
* added support for Accounting-On and Accounting-Off messages
* fixed accounting session handling to send Accounting-Start only once
per session and not to send Accounting-Stop if the session was not
initialized properly
* fixed Accounting-Stop statistics in cases where the message was
previously sent after the kernel entry for the STA (and/or IEEE
802.1X data) was removed
Note:
Older changes up to and including v0.1.0 are included in the ChangeLog
of the Host AP driver.