| #ifndef DMA_EXPORT_H |
| #define DMA_EXPORT_H |
| |
| /**************************************************** |
| * $Id: |
| * |
| * Copyright Motorola 1999 |
| * |
| * $Log: |
| * |
| ****************************************************/ |
| |
| /* These are the defined return values for the DMA_* functions. |
| * Any non-zero value indicates failure. Failure modes can be added for |
| * more detailed error reporting. |
| */ |
| typedef enum _dma_status |
| { |
| DMA_SUCCESS = 0, |
| DMA_ERROR, |
| } DMA_Status; |
| |
| /* These are the defined channel transfer types. */ |
| typedef enum _dma_transfer_types |
| { |
| DMA_M2M = 0, /* local memory to local memory */ |
| DMA_M2P = 1, /* local memory to PCI */ |
| DMA_P2M = 2, /* PCI to local memory */ |
| DMA_P2P = 3, /* PCI to PCI */ |
| } DMA_TRANSFER_TYPE; |
| |
| typedef enum _dma_interrupt_steer |
| { |
| DMA_INT_STEER_LOCAL = 0, /* steer DMA int to local processor */ |
| DMA_INT_STEER_PCI = 1, /* steer DMA int to PCI bus through INTA_ */ |
| } DMA_INTERRUPT_STEER; |
| |
| typedef enum _dma_channel |
| { |
| DMA_CHN_0 = 0, /* kahlua has two dma channels: 0 and 1 */ |
| DMA_CHN_1 = 1, |
| } DMA_CHANNEL; |
| |
| typedef enum _dma_snoop_mode |
| { |
| DMA_SNOOP_DISABLE = 0, |
| DMA_SNOOP_ENABLE = 1, |
| } DMA_SNOOP_MODE; |
| |
| /******************** App. API ******************** |
| * The application API is for user level application |
| * to use the functionality provided by DMA driver. |
| * This is a "generic" DMA interface, it should contain |
| * nothing specific to the Kahlua implementation. |
| * Only the generic functions are exported by the library. |
| * |
| * Note: Its App.s responsibility to swap the data |
| * byte. In our API, we currently transfer whatever |
| * we are given - Big/Little Endian. This could |
| * become part of the DMA config, though. |
| **************************************************/ |
| |
| |
| /* Initialize DMA unit with the following: |
| * optional pointer to application layer print function |
| * |
| * These parameters may be added: |
| * ??? |
| * Interrupt enables, modes, etc. are set for each transfer. |
| * |
| * This function must be called before DMA unit can be used. |
| */ |
| extern DMA_Status DMA_Initialize( |
| int (*app_print_function)(char *,...)); /* pointer to optional "printf" |
| * provided by application |
| */ |
| |
| /* Perform the DMA transfer, only direct mode is currently implemented. |
| * At this point, I think it would be better to define a different |
| * function for chaining mode. |
| * Also, I'm not sure if it is appropriate to have the "generic" API |
| * accept snoop and int_steer parameters. The DINK user interface allows |
| * them, so for now I'll leave them. |
| * |
| * int_steer controls DMA interrupt steering to PCI or local processor |
| * type is the type of transfer: M2M, M2P, P2M, P2P |
| * source is the source address of the data |
| * dest is the destination address of the data |
| * len is the length of data to transfer |
| * channel is the DMA channel to use for the transfer |
| * snoop is the snoop enable control |
| */ |
| extern DMA_Status DMA_direct_transfer( DMA_INTERRUPT_STEER int_steer, |
| DMA_TRANSFER_TYPE type, |
| unsigned int source, |
| unsigned int dest, |
| unsigned int len, |
| DMA_CHANNEL channel, |
| DMA_SNOOP_MODE snoop); |
| #endif |
