blob: 4189f9c995c6d492e75cc5515e1ac27adc6dc955 [file] [log] [blame]
/*
* (C) Copyright 2003
* Texas Instruments.
* Kshitij Gupta <kshitij@ti.com>
* Configuation settings for the TI OMAP Innovator board.
*
* (C) Copyright 2004
* ARM Ltd.
* Philippe Robin, <philippe.robin@arm.com>
* Configuration for Compact Integrator board.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CFG_MEMTEST_START 0x100000
#define CFG_MEMTEST_END 0x10000000
#define CFG_HZ 1000
#define CFG_HZ_CLOCK 1000000 /* Timer 1 is clocked at 1Mhz */
#define CFG_TIMERBASE 0x13000100
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS 1
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r during start up */
/*
* Size of malloc() pool
*/
#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024)
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
/*
* Hardware drivers
*/
#define CONFIG_DRIVER_SMC91111
#define CONFIG_SMC_USE_32_BIT
#define CONFIG_SMC91111_BASE 0xC8000000
#undef CONFIG_SMC91111_EXT_PHY
/*
* NS16550 Configuration
*/
#define CFG_PL011_SERIAL
#define CONFIG_PL011_CLOCK 14745600
#define CONFIG_PL01x_PORTS { (void *)CFG_SERIAL0, (void *)CFG_SERIAL1 }
#define CONFIG_CONS_INDEX 0
#define CONFIG_BAUDRATE 38400
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CFG_SERIAL0 0x16000000
#define CFG_SERIAL1 0x17000000
/*
#define CONFIG_COMMANDS (CFG_CMD_DFL | CFG_CMD_PCI)
*/
#define CONFIG_COMMANDS (CFG_CMD_DHCP | CFG_CMD_IMI | CFG_CMD_NET | CFG_CMD_PING | \
CFG_CMD_BDI | CFG_CMD_MEMORY | CFG_CMD_FLASH | CFG_CMD_ENV \
)
/* #define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT */
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#if 0
#define CONFIG_BOOTDELAY 2
#define CONFIG_BOOTARGS "root=/dev/nfs nfsroot=<IP address>:/<exported rootfs> mem=128M ip=dhcp netdev=27,0,0xfc800000,0xfc800010,eth0 video=clcdfb:0"
#define CONFIG_BOOTCOMMAND "bootp ; bootm"
#endif
/* The kernel command line & boot command below are for a platform flashed with afu.axf
Image 666 Block 0 End Block 0 address 0x24000000 exec 0x24000000- name u-boot
Image 667 Block 1 End Block 13 address 0x24040000 exec 0x24040000- name u-linux
Image 668 Block 14 End Block 33 address 0x24380000 exec 0x24380000- name rootfs
SIB at Block62 End Block62 address 0x24f80000
*/
#define CONFIG_BOOTDELAY 2
#define CONFIG_BOOTARGS "root=/dev/mtdblock2 mem=128M ip=dhcp netdev=27,0,0xfc800000,0xfc800010,eth0 video=clcdfb:0 console=ttyAMA0"
#define CONFIG_BOOTCOMMAND "cp 0x24080000 0x7fc0 0x100000; bootm"
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "Integrator-CP # " /* Monitor Command Prompt */
#define CFG_CBSIZE 256 /* Console I/O Buffer Size*/
/* Print Buffer Size */
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size*/
#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
#define CFG_LOAD_ADDR 0x7fc0 /* default load address */
/*-----------------------------------------------------------------------
* Stack sizes
*
* The stack sizes are set up in start.S using the settings below
*/
#define CONFIG_STACKSIZE (128*1024) /* regular stack */
#ifdef CONFIG_USE_IRQ
#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
#endif
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */
#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */
/*-----------------------------------------------------------------------
* FLASH and environment organization
* Top varies according to amount fitted
* Reserve top 4 blocks of flash
* - ARM Boot Monitor
* - Unused
* - SIB block
* - U-Boot environment
*
* Base is always 0x24000000
*/
#define CFG_FLASH_BASE 0x24000000
#define CFG_MAX_FLASH_SECT 64
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define PHYS_FLASH_SIZE 0x01000000 /* 16MB */
#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* Timeout for Flash Erase */
#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */
#define CFG_MONITOR_LEN 0x00100000
#define CFG_ENV_IS_IN_FLASH (1)
/*
* Move up the U-Boot & monitor area if more flash is fitted.
* If this U-Boot is to be run on Integrators with varying flash sizes,
* drivers/cfi_flash.c::flash_init() can read the Integrator CP_FLASHPROG
* register and dynamically assign CFG_ENV_ADDR & CFG_MONITOR_BASE
* - CFG_MONITOR_BASE is set to indicate that the environment is not
* embedded in the boot monitor(s) area
*/
#if ( PHYS_FLASH_SIZE == 0x04000000 )
#define CFG_ENV_ADDR 0x27F00000
#define CFG_MONITOR_BASE 0x27F40000
#elif (PHYS_FLASH_SIZE == 0x02000000 )
#define CFG_ENV_ADDR 0x25F00000
#define CFG_MONITOR_BASE 0x25F40000
#else
#define CFG_ENV_ADDR 0x24F00000
#define CFG_MONITOR_BASE 0x27F40000
#endif
#define CFG_ENV_SECT_SIZE 0x40000 /* 256KB */
#define CFG_ENV_SIZE 8192 /* 8KB */
/*-----------------------------------------------------------------------
* CP control registers
*/
#define CPCR_BASE 0xCB000000 /* CP Registers*/
#define OS_FLASHPROG 0x00000004 /* Flash register*/
#define CPMASK_EXTRABANK 0x8
#define CPMASK_FLASHSIZE 0x4
#define CPMASK_FLWREN 0x2
#define CPMASK_FLVPPEN 0x1
/*
* The ARM boot monitor initializes the board.
* However, the default U-Boot code also performs the initialization.
* If desired, this can be prevented by defining SKIP_LOWLEVEL_INIT
* - see documentation supplied with board for details of how to choose the
* image to run at reset/power up
* e.g. whether the ARM Boot Monitor runs before U-Boot
#define CONFIG_SKIP_LOWLEVEL_INIT
*/
/*
* The ARM boot monitor does not relocate U-Boot.
* However, the default U-Boot code performs the relocation check,
* and may relocate the code if the memory map is changed.
* If necessary this can be prevented by defining SKIP_RELOCATE_UBOOT
#define SKIP_CONFIG_RELOCATE_UBOOT
*/
/*-----------------------------------------------------------------------
* There are various dependencies on the core module (CM) fitted
* Users should refer to their CM user guide
* - when porting adjust u-boot/Makefile accordingly
* to define the necessary CONFIG_ s for the CM involved
* see e.g. cp_926ejs_config
*/
#include "armcoremodule.h"
/*
* If CONFIG_SKIP_LOWLEVEL_INIT is not defined &
* the core module has a CM_INIT register
* then the U-Boot initialisation code will
* e.g. ARM Boot Monitor or pre-loader is repeated once
* (to re-initialise any existing CM_INIT settings to safe values).
*
* This is usually not the desired behaviour since the platform
* will either reboot into the ARM monitor (or pre-loader)
* or continuously cycle thru it without U-Boot running,
* depending upon the setting of Integrator/CP switch S2-4.
*
* However it may be needed if Integrator/CP switch S2-1
* is set OFF to boot direct into U-Boot.
* In that case comment out the line below.
#undef CONFIG_CM_INIT
*/
#endif /* __CONFIG_H */