#ifndef _IMX_REGS_H
#define _IMX_REGS_H
/* ------------------------------------------------------------------------
 *  Motorola IMX system registers
 * ------------------------------------------------------------------------
 *
 */

#define IO_ADDRESS(x) ((x) | IMX_IO_BASE)

# ifndef __ASSEMBLY__
# define __REG(x)	(*((volatile u32 *)IO_ADDRESS(x)))
# define __REG2(x,y)        (*(volatile u32 *)((u32)&__REG(x) + (y)))
# else
#  define __REG(x) (x)
#  define __REG2(x,y) ((x)+(y))
#endif

#define IMX_IO_BASE		0x00200000

/*
 *  Register BASEs, based on OFFSETs
 *
 */
#define IMX_AIPI1_BASE             (0x00000 + IMX_IO_BASE)
#define IMX_WDT_BASE               (0x01000 + IMX_IO_BASE)
#define IMX_TIM1_BASE              (0x02000 + IMX_IO_BASE)
#define IMX_TIM2_BASE              (0x03000 + IMX_IO_BASE)
#define IMX_RTC_BASE               (0x04000 + IMX_IO_BASE)
#define IMX_LCDC_BASE              (0x05000 + IMX_IO_BASE)
#define IMX_UART1_BASE             (0x06000 + IMX_IO_BASE)
#define IMX_UART2_BASE             (0x07000 + IMX_IO_BASE)
#define IMX_PWM_BASE               (0x08000 + IMX_IO_BASE)
#define IMX_DMAC_BASE              (0x09000 + IMX_IO_BASE)
#define IMX_AIPI2_BASE             (0x10000 + IMX_IO_BASE)
#define IMX_SIM_BASE               (0x11000 + IMX_IO_BASE)
#define IMX_USBD_BASE              (0x12000 + IMX_IO_BASE)
#define IMX_SPI1_BASE              (0x13000 + IMX_IO_BASE)
#define IMX_MMC_BASE               (0x14000 + IMX_IO_BASE)
#define IMX_ASP_BASE               (0x15000 + IMX_IO_BASE)
#define IMX_BTA_BASE               (0x16000 + IMX_IO_BASE)
#define IMX_I2C_BASE               (0x17000 + IMX_IO_BASE)
#define IMX_SSI_BASE               (0x18000 + IMX_IO_BASE)
#define IMX_SPI2_BASE              (0x19000 + IMX_IO_BASE)
#define IMX_MSHC_BASE              (0x1A000 + IMX_IO_BASE)
#define IMX_PLL_BASE               (0x1B000 + IMX_IO_BASE)
#define IMX_SYSCTRL_BASE           (0x1B800 + IMX_IO_BASE)
#define IMX_GPIO_BASE              (0x1C000 + IMX_IO_BASE)
#define IMX_EIM_BASE               (0x20000 + IMX_IO_BASE)
#define IMX_SDRAMC_BASE            (0x21000 + IMX_IO_BASE)
#define IMX_MMA_BASE               (0x22000 + IMX_IO_BASE)
#define IMX_AITC_BASE              (0x23000 + IMX_IO_BASE)
#define IMX_CSI_BASE               (0x24000 + IMX_IO_BASE)

/* Watchdog Registers*/

#define WCR  __REG(IMX_WDT_BASE + 0x00) /* Watchdog Control Register */
#define WSR  __REG(IMX_WDT_BASE + 0x04) /* Watchdog Service Register */
#define WSTR __REG(IMX_WDT_BASE + 0x08) /* Watchdog Status Register  */

/* SYSCTRL Registers */
#define SIDR   __REG(IMX_SYSCTRL_BASE + 0x4) /* Silicon ID Register		    */
#define FMCR   __REG(IMX_SYSCTRL_BASE + 0x8) /* Function Multiplex Control Register */
#define GPCR   __REG(IMX_SYSCTRL_BASE + 0xC) /* Function Multiplex Control Register */

/* Chip Select Registers */
#define CS0U __REG(IMX_EIM_BASE)        /* Chip Select 0 Upper Register */
#define CS0L __REG(IMX_EIM_BASE + 0x4)  /* Chip Select 0 Lower Register */
#define CS1U __REG(IMX_EIM_BASE + 0x8)  /* Chip Select 1 Upper Register */
#define CS1L __REG(IMX_EIM_BASE + 0xc)  /* Chip Select 1 Lower Register */
#define CS2U __REG(IMX_EIM_BASE + 0x10) /* Chip Select 2 Upper Register */
#define CS2L __REG(IMX_EIM_BASE + 0x14) /* Chip Select 2 Lower Register */
#define CS3U __REG(IMX_EIM_BASE + 0x18) /* Chip Select 3 Upper Register */
#define CS3L __REG(IMX_EIM_BASE + 0x1c) /* Chip Select 3 Lower Register */
#define CS4U __REG(IMX_EIM_BASE + 0x20) /* Chip Select 4 Upper Register */
#define CS4L __REG(IMX_EIM_BASE + 0x24) /* Chip Select 4 Lower Register */
#define CS5U __REG(IMX_EIM_BASE + 0x28) /* Chip Select 5 Upper Register */
#define CS5L __REG(IMX_EIM_BASE + 0x2c) /* Chip Select 5 Lower Register */
#define EIM  __REG(IMX_EIM_BASE + 0x30) /* EIM Configuration Register */

/* SDRAM controller registers */

#define SDCTL0 __REG(IMX_SDRAMC_BASE)        /* SDRAM 0 Control Register */
#define SDCTL1 __REG(IMX_SDRAMC_BASE + 0x4)  /* SDRAM 1 Control Register */
#define SDMISC __REG(IMX_SDRAMC_BASE + 0x14) /* Miscellaneous Register */
#define SDRST  __REG(IMX_SDRAMC_BASE + 0x18) /* SDRAM Reset Register */

/* PLL registers */
#define CSCR   __REG(IMX_PLL_BASE)        /* Clock Source Control Register */
#define CSCR_SPLL_RESTART	(1<<22)
#define CSCR_MPLL_RESTART	(1<<21)
#define CSCR_SYSTEM_SEL		(1<<16)
#define CSCR_BCLK_DIV		(0xf<<10)
#define CSCR_MPU_PRESC		(1<<15)
#define CSCR_SPEN		(1<<1)
#define CSCR_MPEN		(1<<0)

#define MPCTL0 __REG(IMX_PLL_BASE + 0x4)  /* MCU PLL Control Register 0 */
#define MPCTL1 __REG(IMX_PLL_BASE + 0x8)  /* MCU PLL and System Clock Register 1 */
#define SPCTL0 __REG(IMX_PLL_BASE + 0xc)  /* System PLL Control Register 0 */
#define SPCTL1 __REG(IMX_PLL_BASE + 0x10) /* System PLL Control Register 1 */
#define PCDR   __REG(IMX_PLL_BASE + 0x20) /* Peripheral Clock Divider Register */

/*
 *  GPIO Module and I/O Multiplexer
 *  x = 0..3 for reg_A, reg_B, reg_C, reg_D
 */
#define DDIR(x)    __REG2(IMX_GPIO_BASE + 0x00, ((x) & 3) << 8)
#define OCR1(x)    __REG2(IMX_GPIO_BASE + 0x04, ((x) & 3) << 8)
#define OCR2(x)    __REG2(IMX_GPIO_BASE + 0x08, ((x) & 3) << 8)
#define ICONFA1(x) __REG2(IMX_GPIO_BASE + 0x0c, ((x) & 3) << 8)
#define ICONFA2(x) __REG2(IMX_GPIO_BASE + 0x10, ((x) & 3) << 8)
#define ICONFB1(x) __REG2(IMX_GPIO_BASE + 0x14, ((x) & 3) << 8)
#define ICONFB2(x) __REG2(IMX_GPIO_BASE + 0x18, ((x) & 3) << 8)
#define DR(x)      __REG2(IMX_GPIO_BASE + 0x1c, ((x) & 3) << 8)
#define GIUS(x)    __REG2(IMX_GPIO_BASE + 0x20, ((x) & 3) << 8)
#define SSR(x)     __REG2(IMX_GPIO_BASE + 0x24, ((x) & 3) << 8)
#define ICR1(x)    __REG2(IMX_GPIO_BASE + 0x28, ((x) & 3) << 8)
#define ICR2(x)    __REG2(IMX_GPIO_BASE + 0x2c, ((x) & 3) << 8)
#define IMR(x)     __REG2(IMX_GPIO_BASE + 0x30, ((x) & 3) << 8)
#define ISR(x)     __REG2(IMX_GPIO_BASE + 0x34, ((x) & 3) << 8)
#define GPR(x)     __REG2(IMX_GPIO_BASE + 0x38, ((x) & 3) << 8)
#define SWR(x)     __REG2(IMX_GPIO_BASE + 0x3c, ((x) & 3) << 8)
#define PUEN(x)    __REG2(IMX_GPIO_BASE + 0x40, ((x) & 3) << 8)

#define GPIO_PORT_MAX  3

#define GPIO_PIN_MASK 0x1f
#define GPIO_PORT_MASK (0x3 << 5)

#define GPIO_PORT_SHIFT 5
#define GPIO_PORTA (0<<5)
#define GPIO_PORTB (1<<5)
#define GPIO_PORTC (2<<5)
#define GPIO_PORTD (3<<5)

#define GPIO_OUT   (1<<7)
#define GPIO_IN    (0<<7)
#define GPIO_PUEN  (1<<8)

#define GPIO_PF    (0<<9)
#define GPIO_AF    (1<<9)

#define GPIO_OCR_SHIFT 10
#define GPIO_OCR_MASK (3<<10)
#define GPIO_AIN   (0<<10)
#define GPIO_BIN   (1<<10)
#define GPIO_CIN   (2<<10)
#define GPIO_DR    (3<<10)

#define GPIO_AOUT_SHIFT 12
#define GPIO_AOUT_MASK (3<<12)
#define GPIO_AOUT     (0<<12)
#define GPIO_AOUT_ISR (1<<12)
#define GPIO_AOUT_0   (2<<12)
#define GPIO_AOUT_1   (3<<12)

#define GPIO_BOUT_SHIFT 14
#define GPIO_BOUT_MASK (3<<14)
#define GPIO_BOUT      (0<<14)
#define GPIO_BOUT_ISR  (1<<14)
#define GPIO_BOUT_0    (2<<14)
#define GPIO_BOUT_1    (3<<14)

#define GPIO_GIUS      (1<<16)

/* assignements for GPIO alternate/primary functions */

/* FIXME: This list is not completed. The correct directions are
 * missing on some (many) pins
 */
#define PA0_AIN_SPI2_CLK     ( GPIO_GIUS | GPIO_PORTA | GPIO_OUT | 0 )
#define PA0_AF_ETMTRACESYNC  ( GPIO_PORTA | GPIO_AF | 0 )
#define PA1_AOUT_SPI2_RXD    ( GPIO_GIUS | GPIO_PORTA | GPIO_IN | 1 )
#define PA1_PF_TIN           ( GPIO_PORTA | GPIO_PF | 1 )
#define PA2_PF_PWM0          ( GPIO_PORTA | GPIO_OUT | GPIO_PF | 2 )
#define PA3_PF_CSI_MCLK      ( GPIO_PORTA | GPIO_PF | 3 )
#define PA4_PF_CSI_D0        ( GPIO_PORTA | GPIO_PF | 4 )
#define PA5_PF_CSI_D1        ( GPIO_PORTA | GPIO_PF | 5 )
#define PA6_PF_CSI_D2        ( GPIO_PORTA | GPIO_PF | 6 )
#define PA7_PF_CSI_D3        ( GPIO_PORTA | GPIO_PF | 7 )
#define PA8_PF_CSI_D4        ( GPIO_PORTA | GPIO_PF | 8 )
#define PA9_PF_CSI_D5        ( GPIO_PORTA | GPIO_PF | 9 )
#define PA10_PF_CSI_D6       ( GPIO_PORTA | GPIO_PF | 10 )
#define PA11_PF_CSI_D7       ( GPIO_PORTA | GPIO_PF | 11 )
#define PA12_PF_CSI_VSYNC    ( GPIO_PORTA | GPIO_PF | 12 )
#define PA13_PF_CSI_HSYNC    ( GPIO_PORTA | GPIO_PF | 13 )
#define PA14_PF_CSI_PIXCLK   ( GPIO_PORTA | GPIO_PF | 14 )
#define PA15_PF_I2C_SDA      ( GPIO_PORTA | GPIO_OUT | GPIO_PF | 15 )
#define PA16_PF_I2C_SCL      ( GPIO_PORTA | GPIO_OUT | GPIO_PF | 16 )
#define PA17_AF_ETMTRACEPKT4 ( GPIO_PORTA | GPIO_AF | 17 )
#define PA17_AIN_SPI2_SS     ( GPIO_GIUS | GPIO_PORTA | GPIO_OUT | 17 )
#define PA18_AF_ETMTRACEPKT5 ( GPIO_PORTA | GPIO_AF | 18 )
#define PA19_AF_ETMTRACEPKT6 ( GPIO_PORTA | GPIO_AF | 19 )
#define PA20_AF_ETMTRACEPKT7 ( GPIO_PORTA | GPIO_AF | 20 )
#define PA21_PF_A0           ( GPIO_PORTA | GPIO_PF | 21 )
#define PA22_PF_CS4          ( GPIO_PORTA | GPIO_PF | 22 )
#define PA23_PF_CS5          ( GPIO_PORTA | GPIO_PF | 23 )
#define PA24_PF_A16          ( GPIO_PORTA | GPIO_PF | 24 )
#define PA24_AF_ETMTRACEPKT0 ( GPIO_PORTA | GPIO_AF | 24 )
#define PA25_PF_A17          ( GPIO_PORTA | GPIO_PF | 25 )
#define PA25_AF_ETMTRACEPKT1 ( GPIO_PORTA | GPIO_AF | 25 )
#define PA26_PF_A18          ( GPIO_PORTA | GPIO_PF | 26 )
#define PA26_AF_ETMTRACEPKT2 ( GPIO_PORTA | GPIO_AF | 26 )
#define PA27_PF_A19          ( GPIO_PORTA | GPIO_PF | 27 )
#define PA27_AF_ETMTRACEPKT3 ( GPIO_PORTA | GPIO_AF | 27 )
#define PA28_PF_A20          ( GPIO_PORTA | GPIO_PF | 28 )
#define PA28_AF_ETMPIPESTAT0 ( GPIO_PORTA | GPIO_AF | 28 )
#define PA29_PF_A21          ( GPIO_PORTA | GPIO_PF | 29 )
#define PA29_AF_ETMPIPESTAT1 ( GPIO_PORTA | GPIO_AF | 29 )
#define PA30_PF_A22          ( GPIO_PORTA | GPIO_PF | 30 )
#define PA30_AF_ETMPIPESTAT2 ( GPIO_PORTA | GPIO_AF | 30 )
#define PA31_PF_A23          ( GPIO_PORTA | GPIO_PF | 31 )
#define PA31_AF_ETMTRACECLK  ( GPIO_PORTA | GPIO_AF | 31 )
#define PB8_PF_SD_DAT0       ( GPIO_PORTB | GPIO_PF | GPIO_PUEN | 8 )
#define PB8_AF_MS_PIO        ( GPIO_PORTB | GPIO_AF | 8 )
#define PB9_PF_SD_DAT1       ( GPIO_PORTB | GPIO_PF | GPIO_PUEN  | 9 )
#define PB9_AF_MS_PI1        ( GPIO_PORTB | GPIO_AF | 9 )
#define PB10_PF_SD_DAT2      ( GPIO_PORTB | GPIO_PF | GPIO_PUEN  | 10 )
#define PB10_AF_MS_SCLKI     ( GPIO_PORTB | GPIO_AF | 10 )
#define PB11_PF_SD_DAT3      ( GPIO_PORTB | GPIO_PF | 11 )
#define PB11_AF_MS_SDIO      ( GPIO_PORTB | GPIO_AF | 11 )
#define PB12_PF_SD_CLK       ( GPIO_PORTB | GPIO_PF | 12 )
#define PB12_AF_MS_SCLK0     ( GPIO_PORTB | GPIO_AF | 12 )
#define PB13_PF_SD_CMD       ( GPIO_PORTB | GPIO_PF | GPIO_PUEN | 13 )
#define PB13_AF_MS_BS        ( GPIO_PORTB | GPIO_AF | 13 )
#define PB14_AF_SSI_RXFS     ( GPIO_PORTB | GPIO_AF | 14 )
#define PB15_AF_SSI_RXCLK    ( GPIO_PORTB | GPIO_AF | 15 )
#define PB16_AF_SSI_RXDAT    ( GPIO_PORTB | GPIO_IN | GPIO_AF | 16 )
#define PB17_AF_SSI_TXDAT    ( GPIO_PORTB | GPIO_OUT | GPIO_AF | 17 )
#define PB18_AF_SSI_TXFS     ( GPIO_PORTB | GPIO_AF | 18 )
#define PB19_AF_SSI_TXCLK    ( GPIO_PORTB | GPIO_AF | 19 )
#define PB20_PF_USBD_AFE     ( GPIO_PORTB | GPIO_PF | 20 )
#define PB21_PF_USBD_OE      ( GPIO_PORTB | GPIO_PF | 21 )
#define PB22_PFUSBD_RCV      ( GPIO_PORTB | GPIO_PF | 22 )
#define PB23_PF_USBD_SUSPND  ( GPIO_PORTB | GPIO_PF | 23 )
#define PB24_PF_USBD_VP      ( GPIO_PORTB | GPIO_PF | 24 )
#define PB25_PF_USBD_VM      ( GPIO_PORTB | GPIO_PF | 25 )
#define PB26_PF_USBD_VPO     ( GPIO_PORTB | GPIO_PF | 26 )
#define PB27_PF_USBD_VMO     ( GPIO_PORTB | GPIO_PF | 27 )
#define PB28_PF_UART2_CTS    ( GPIO_PORTB | GPIO_OUT | GPIO_PF | 28 )
#define PB29_PF_UART2_RTS    ( GPIO_PORTB | GPIO_IN | GPIO_PF | 29 )
#define PB30_PF_UART2_TXD    ( GPIO_PORTB | GPIO_OUT | GPIO_PF | 30 )
#define PB31_PF_UART2_RXD    ( GPIO_PORTB | GPIO_IN | GPIO_PF | 31 )
#define PC3_PF_SSI_RXFS      ( GPIO_PORTC | GPIO_PF | 3 )
#define PC4_PF_SSI_RXCLK     ( GPIO_PORTC | GPIO_PF | 4 )
#define PC5_PF_SSI_RXDAT     ( GPIO_PORTC | GPIO_IN | GPIO_PF | 5 )
#define PC6_PF_SSI_TXDAT     ( GPIO_PORTC | GPIO_OUT | GPIO_PF | 6 )
#define PC7_PF_SSI_TXFS      ( GPIO_PORTC | GPIO_PF | 7 )
#define PC8_PF_SSI_TXCLK     ( GPIO_PORTC | GPIO_PF | 8 )
#define PC9_PF_UART1_CTS     ( GPIO_PORTC | GPIO_OUT | GPIO_PF | 9 )
#define PC10_PF_UART1_RTS    ( GPIO_PORTC | GPIO_IN | GPIO_PF | 10 )
#define PC11_PF_UART1_TXD    ( GPIO_PORTC | GPIO_OUT | GPIO_PF | 11 )
#define PC12_PF_UART1_RXD    ( GPIO_PORTC | GPIO_IN | GPIO_PF | 12 )
#define PC13_PF_SPI1_SPI_RDY ( GPIO_PORTC | GPIO_PF | 13 )
#define PC14_PF_SPI1_SCLK    ( GPIO_PORTC | GPIO_PF | 14 )
#define PC15_PF_SPI1_SS      ( GPIO_PORTC | GPIO_PF | 15 )
#define PC16_PF_SPI1_MISO    ( GPIO_PORTC | GPIO_PF | 16 )
#define PC17_PF_SPI1_MOSI    ( GPIO_PORTC | GPIO_PF | 17 )
#define PC24_BIN_UART3_RI    ( GPIO_GIUS | GPIO_PORTC | GPIO_OUT | GPIO_BIN | 24 )
#define PC25_BIN_UART3_DSR   ( GPIO_GIUS | GPIO_PORTC | GPIO_OUT | GPIO_BIN | 25 )
#define PC26_AOUT_UART3_DTR  ( GPIO_GIUS | GPIO_PORTC | GPIO_IN | 26 )
#define PC27_BIN_UART3_DCD   ( GPIO_GIUS | GPIO_PORTC | GPIO_OUT | GPIO_BIN | 27 )
#define PC28_BIN_UART3_CTS   ( GPIO_GIUS | GPIO_PORTC | GPIO_OUT | GPIO_BIN | 28 )
#define PC29_AOUT_UART3_RTS  ( GPIO_GIUS | GPIO_PORTC | GPIO_IN | 29 )
#define PC30_BIN_UART3_TX    ( GPIO_GIUS | GPIO_PORTC | GPIO_BIN | 30 )
#define PC31_AOUT_UART3_RX   ( GPIO_GIUS | GPIO_PORTC | GPIO_IN | 31)
#define PD6_PF_LSCLK         ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 6 )
#define PD7_PF_REV           ( GPIO_PORTD | GPIO_PF | 7 )
#define PD7_AF_UART2_DTR     ( GPIO_GIUS | GPIO_PORTD | GPIO_IN | GPIO_AF | 7 )
#define PD7_AIN_SPI2_SCLK    ( GPIO_GIUS | GPIO_PORTD | GPIO_AIN | 7 )
#define PD8_PF_CLS           ( GPIO_PORTD | GPIO_PF | 8 )
#define PD8_AF_UART2_DCD     ( GPIO_PORTD | GPIO_OUT | GPIO_AF | 8 )
#define PD8_AIN_SPI2_SS      ( GPIO_GIUS | GPIO_PORTD | GPIO_AIN | 8 )
#define PD9_PF_PS            ( GPIO_PORTD | GPIO_PF | 9 )
#define PD9_AF_UART2_RI      ( GPIO_PORTD | GPIO_OUT | GPIO_AF | 9 )
#define PD9_AOUT_SPI2_RXD    ( GPIO_GIUS | GPIO_PORTD | GPIO_IN | 9 )
#define PD10_PF_SPL_SPR      ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 10 )
#define PD10_AF_UART2_DSR    ( GPIO_PORTD | GPIO_OUT | GPIO_AF | 10 )
#define PD10_AIN_SPI2_TXD    ( GPIO_GIUS | GPIO_PORTD | GPIO_OUT | 10 )
#define PD11_PF_CONTRAST     ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 11 )
#define PD12_PF_ACD_OE       ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 12 )
#define PD13_PF_LP_HSYNC     ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 13 )
#define PD14_PF_FLM_VSYNC    ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 14 )
#define PD15_PF_LD0          ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 15 )
#define PD16_PF_LD1          ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 16 )
#define PD17_PF_LD2          ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 17 )
#define PD18_PF_LD3          ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 18 )
#define PD19_PF_LD4          ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 19 )
#define PD20_PF_LD5          ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 20 )
#define PD21_PF_LD6          ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 21 )
#define PD22_PF_LD7          ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 22 )
#define PD23_PF_LD8          ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 23 )
#define PD24_PF_LD9          ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 24 )
#define PD25_PF_LD10         ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 25 )
#define PD26_PF_LD11         ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 26 )
#define PD27_PF_LD12         ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 27 )
#define PD28_PF_LD13         ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 28 )
#define PD29_PF_LD14         ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 29 )
#define PD30_PF_LD15         ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 30 )
#define PD31_PF_TMR2OUT      ( GPIO_PORTD | GPIO_PF | 31 )
#define PD31_BIN_SPI2_TXD    ( GPIO_GIUS | GPIO_PORTD | GPIO_BIN | 31 )

/*
 * PWM controller
 */
#define PWMC	__REG(IMX_PWM_BASE + 0x00)	/* PWM Control Register		*/
#define PWMS	__REG(IMX_PWM_BASE + 0x04)	/* PWM Sample Register		*/
#define PWMP	__REG(IMX_PWM_BASE + 0x08)	/* PWM Period Register		*/
#define PWMCNT	__REG(IMX_PWM_BASE + 0x0C)	/* PWM Counter Register		*/

#define PWMC_HCTR		(0x01<<18)		/* Halfword FIFO Data Swapping	*/
#define PWMC_BCTR		(0x01<<17)		/* Byte FIFO Data Swapping	*/
#define PWMC_SWR		(0x01<<16)		/* Software Reset		*/
#define PWMC_CLKSRC		(0x01<<15)		/* Clock Source			*/
#define PWMC_PRESCALER(x)	(((x-1) & 0x7F) << 8)	/* PRESCALER			*/
#define PWMC_IRQ		(0x01<< 7)		/* Interrupt Request		*/
#define PWMC_IRQEN		(0x01<< 6)		/* Interrupt Request Enable	*/
#define PWMC_FIFOAV		(0x01<< 5)		/* FIFO Available		*/
#define PWMC_EN			(0x01<< 4)		/* Enables/Disables the PWM	*/
#define PWMC_REPEAT(x)		(((x) & 0x03) << 2)	/* Sample Repeats		*/
#define PWMC_CLKSEL(x)		(((x) & 0x03) << 0)	/* Clock Selection		*/

#define PWMS_SAMPLE(x)		((x) & 0xFFFF)		/* Contains a two-sample word	*/
#define PWMP_PERIOD(x)		((x) & 0xFFFF)		/* Represents the PWM's period	*/
#define PWMC_COUNTER(x)		((x) & 0xFFFF)		/* Represents the current count value	*/

/*
 *  DMA Controller
 */
#define DCR     __REG(IMX_DMAC_BASE +0x00)	/* DMA Control Register */
#define DISR    __REG(IMX_DMAC_BASE +0x04)	/* DMA Interrupt status Register */
#define DIMR    __REG(IMX_DMAC_BASE +0x08)	/* DMA Interrupt mask Register */
#define DBTOSR  __REG(IMX_DMAC_BASE +0x0c)	/* DMA Burst timeout status Register */
#define DRTOSR  __REG(IMX_DMAC_BASE +0x10)	/* DMA Request timeout Register */
#define DSESR   __REG(IMX_DMAC_BASE +0x14)	/* DMA Transfer Error Status Register */
#define DBOSR   __REG(IMX_DMAC_BASE +0x18)	/* DMA Buffer overflow status Register */
#define DBTOCR  __REG(IMX_DMAC_BASE +0x1c)	/* DMA Burst timeout control Register */
#define WSRA    __REG(IMX_DMAC_BASE +0x40)	/* W-Size Register A */
#define XSRA    __REG(IMX_DMAC_BASE +0x44)	/* X-Size Register A */
#define YSRA    __REG(IMX_DMAC_BASE +0x48)	/* Y-Size Register A */
#define WSRB    __REG(IMX_DMAC_BASE +0x4c)	/* W-Size Register B */
#define XSRB    __REG(IMX_DMAC_BASE +0x50)	/* X-Size Register B */
#define YSRB    __REG(IMX_DMAC_BASE +0x54)	/* Y-Size Register B */
#define SAR(x)  __REG2( IMX_DMAC_BASE + 0x80, (x) << 6)	/* Source Address Registers */
#define DAR(x)  __REG2( IMX_DMAC_BASE + 0x84, (x) << 6)	/* Destination Address Registers */
#define CNTR(x) __REG2( IMX_DMAC_BASE + 0x88, (x) << 6)	/* Count Registers */
#define CCR(x)  __REG2( IMX_DMAC_BASE + 0x8c, (x) << 6)	/* Control Registers */
#define RSSR(x) __REG2( IMX_DMAC_BASE + 0x90, (x) << 6)	/* Request source select Registers */
#define BLR(x)  __REG2( IMX_DMAC_BASE + 0x94, (x) << 6)	/* Burst length Registers */
#define RTOR(x) __REG2( IMX_DMAC_BASE + 0x98, (x) << 6)	/* Request timeout Registers */
#define BUCR(x) __REG2( IMX_DMAC_BASE + 0x98, (x) << 6)	/* Bus Utilization Registers */

/* TODO: define DMA_REQ lines */

#define DCR_DRST           (1<<1)
#define DCR_DEN            (1<<0)
#define DBTOCR_EN          (1<<15)
#define DBTOCR_CNT(x)      ((x) & 0x7fff )
#define CNTR_CNT(x)        ((x) & 0xffffff )
#define CCR_DMOD_LINEAR    ( 0x0 << 12 )
#define CCR_DMOD_2D        ( 0x1 << 12 )
#define CCR_DMOD_FIFO      ( 0x2 << 12 )
#define CCR_DMOD_EOBFIFO   ( 0x3 << 12 )
#define CCR_SMOD_LINEAR    ( 0x0 << 10 )
#define CCR_SMOD_2D        ( 0x1 << 10 )
#define CCR_SMOD_FIFO      ( 0x2 << 10 )
#define CCR_SMOD_EOBFIFO   ( 0x3 << 10 )
#define CCR_MDIR_DEC       (1<<9)
#define CCR_MSEL_B         (1<<8)
#define CCR_DSIZ_32        ( 0x0 << 6 )
#define CCR_DSIZ_8         ( 0x1 << 6 )
#define CCR_DSIZ_16        ( 0x2 << 6 )
#define CCR_SSIZ_32        ( 0x0 << 4 )
#define CCR_SSIZ_8         ( 0x1 << 4 )
#define CCR_SSIZ_16        ( 0x2 << 4 )
#define CCR_REN            (1<<3)
#define CCR_RPT            (1<<2)
#define CCR_FRC            (1<<1)
#define CCR_CEN            (1<<0)
#define RTOR_EN            (1<<15)
#define RTOR_CLK           (1<<14)
#define RTOR_PSC           (1<<13)

/*
 * LCD Controller
 */

#define LCDC_SSA	__REG(IMX_LCDC_BASE+0x00)

#define LCDC_SIZE	__REG(IMX_LCDC_BASE+0x04)
#define SIZE_XMAX(x)	((((x) >> 4) & 0x3f) << 20)
#define SIZE_YMAX(y)    ( (y) & 0x1ff )

#define LCDC_VPW	__REG(IMX_LCDC_BASE+0x08)
#define VPW_VPW(x)	( (x) & 0x3ff )

#define LCDC_CPOS	__REG(IMX_LCDC_BASE+0x0C)
#define CPOS_CC1        (1<<31)
#define CPOS_CC0        (1<<30)
#define CPOS_OP         (1<<28)
#define CPOS_CXP(x)     (((x) & 3ff) << 16)
#define CPOS_CYP(y)     ((y) & 0x1ff)

#define LCDC_LCWHB	__REG(IMX_LCDC_BASE+0x10)
#define LCWHB_BK_EN     (1<<31)
#define LCWHB_CW(w)     (((w) & 0x1f) << 24)
#define LCWHB_CH(h)     (((h) & 0x1f) << 16)
#define LCWHB_BD(x)     ((x) & 0xff)

#define LCDC_LCHCC	__REG(IMX_LCDC_BASE+0x14)
#define LCHCC_CUR_COL_R(r) (((r) & 0x1f) << 11)
#define LCHCC_CUR_COL_G(g) (((g) & 0x3f) << 5)
#define LCHCC_CUR_COL_B(b) ((b) & 0x1f)

#define LCDC_PCR	__REG(IMX_LCDC_BASE+0x18)
#define PCR_TFT         (1<<31)
#define PCR_COLOR       (1<<30)
#define PCR_PBSIZ_1     (0<<28)
#define PCR_PBSIZ_2     (1<<28)
#define PCR_PBSIZ_4     (2<<28)
#define PCR_PBSIZ_8     (3<<28)
#define PCR_BPIX_1      (0<<25)
#define PCR_BPIX_2      (1<<25)
#define PCR_BPIX_4      (2<<25)
#define PCR_BPIX_8      (3<<25)
#define PCR_BPIX_12     (4<<25)
#define PCR_BPIX_16     (4<<25)
#define PCR_PIXPOL      (1<<24)
#define PCR_FLMPOL      (1<<23)
#define PCR_LPPOL       (1<<22)
#define PCR_CLKPOL      (1<<21)
#define PCR_OEPOL       (1<<20)
#define PCR_SCLKIDLE    (1<<19)
#define PCR_END_SEL     (1<<18)
#define PCR_END_BYTE_SWAP (1<<17)
#define PCR_REV_VS      (1<<16)
#define PCR_ACD_SEL     (1<<15)
#define PCR_ACD(x)      (((x) & 0x7f) << 8)
#define PCR_SCLK_SEL    (1<<7)
#define PCR_SHARP       (1<<6)
#define PCR_PCD(x)      ((x) & 0x3f)

#define LCDC_HCR	__REG(IMX_LCDC_BASE+0x1C)
#define HCR_H_WIDTH(x)  (((x) & 0x3f) << 26)
#define HCR_H_WAIT_1(x) (((x) & 0xff) << 8)
#define HCR_H_WAIT_2(x) ((x) & 0xff)

#define LCDC_VCR	__REG(IMX_LCDC_BASE+0x20)
#define VCR_V_WIDTH(x)  (((x) & 0x3f) << 26)
#define VCR_V_WAIT_1(x) (((x) & 0xff) << 8)
#define VCR_V_WAIT_2(x) ((x) & 0xff)

#define LCDC_POS	__REG(IMX_LCDC_BASE+0x24)
#define POS_POS(x)      ((x) & 1f)

#define LCDC_LSCR1	__REG(IMX_LCDC_BASE+0x28)
#define LSCR1_PS_RISE_DELAY(x)    (((x) & 0x7f) << 26)
#define LSCR1_CLS_RISE_DELAY(x)   (((x) & 0x3f) << 16)
#define LSCR1_REV_TOGGLE_DELAY(x) (((x) & 0xf) << 8)
#define LSCR1_GRAY2(x)            (((x) & 0xf) << 4)
#define LSCR1_GRAY1(x)            (((x) & 0xf))

#define LCDC_PWMR	__REG(IMX_LCDC_BASE+0x2C)
#define PWMR_CLS(x)     (((x) & 0x1ff) << 16)
#define PWMR_LDMSK      (1<<15)
#define PWMR_SCR1       (1<<10)
#define PWMR_SCR0       (1<<9)
#define PWMR_CC_EN      (1<<8)
#define PWMR_PW(x)      ((x) & 0xff)

#define LCDC_DMACR	__REG(IMX_LCDC_BASE+0x30)
#define DMACR_BURST     (1<<31)
#define DMACR_HM(x)     (((x) & 0xf) << 16)
#define DMACR_TM(x)     ((x) &0xf)

#define LCDC_RMCR	__REG(IMX_LCDC_BASE+0x34)
#define RMCR_LCDC_EN		(1<<1)
#define RMCR_SELF_REF		(1<<0)

#define LCDC_LCDICR	__REG(IMX_LCDC_BASE+0x38)
#define LCDICR_INT_SYN  (1<<2)
#define LCDICR_INT_CON  (1)

#define LCDC_LCDISR	__REG(IMX_LCDC_BASE+0x40)
#define LCDISR_UDR_ERR (1<<3)
#define LCDISR_ERR_RES (1<<2)
#define LCDISR_EOF     (1<<1)
#define LCDISR_BOF     (1<<0)
/*
 *  UART Module
 */
#define URXD0(x) __REG2( IMX_UART1_BASE + 0x0, ((x) & 1) << 12)	/* Receiver Register */
#define URTX0(x) __REG2( IMX_UART1_BASE + 0x40, ((x) & 1) << 12)	/* Transmitter Register */
#define UCR1(x)  __REG2( IMX_UART1_BASE + 0x80, ((x) & 1) << 12)	/* Control Register 1 */
#define UCR2(x)  __REG2( IMX_UART1_BASE + 0x84, ((x) & 1) << 12)	/* Control Register 2 */
#define UCR3(x)  __REG2( IMX_UART1_BASE + 0x88, ((x) & 1) << 12)	/* Control Register 3 */
#define UCR4(x)  __REG2( IMX_UART1_BASE + 0x8c, ((x) & 1) << 12)	/* Control Register 4 */
#define UFCR(x)  __REG2( IMX_UART1_BASE + 0x90, ((x) & 1) << 12)	/* FIFO Control Register */
#define USR1(x)  __REG2( IMX_UART1_BASE + 0x94, ((x) & 1) << 12)	/* Status Register 1 */
#define USR2(x)  __REG2( IMX_UART1_BASE + 0x98, ((x) & 1) << 12)	/* Status Register 2 */
#define UESC(x)  __REG2( IMX_UART1_BASE + 0x9c, ((x) & 1) << 12)	/* Escape Character Register */
#define UTIM(x)  __REG2( IMX_UART1_BASE + 0xa0, ((x) & 1) << 12)	/* Escape Timer Register */
#define UBIR(x)  __REG2( IMX_UART1_BASE + 0xa4, ((x) & 1) << 12)	/* BRM Incremental Register */
#define UBMR(x)  __REG2( IMX_UART1_BASE + 0xa8, ((x) & 1) << 12)	/* BRM Modulator Register */
#define UBRC(x)  __REG2( IMX_UART1_BASE + 0xac, ((x) & 1) << 12)	/* Baud Rate Count Register */
#define BIPR1(x) __REG2( IMX_UART1_BASE + 0xb0, ((x) & 1) << 12)	/* Incremental Preset Register 1 */
#define BIPR2(x) __REG2( IMX_UART1_BASE + 0xb4, ((x) & 1) << 12)	/* Incremental Preset Register 2 */
#define BIPR3(x) __REG2( IMX_UART1_BASE + 0xb8, ((x) & 1) << 12)	/* Incremental Preset Register 3 */
#define BIPR4(x) __REG2( IMX_UART1_BASE + 0xbc, ((x) & 1) << 12)	/* Incremental Preset Register 4 */
#define BMPR1(x) __REG2( IMX_UART1_BASE + 0xc0, ((x) & 1) << 12)	/* BRM Modulator Register 1 */
#define BMPR2(x) __REG2( IMX_UART1_BASE + 0xc4, ((x) & 1) << 12)	/* BRM Modulator Register 2 */
#define BMPR3(x) __REG2( IMX_UART1_BASE + 0xc8, ((x) & 1) << 12)	/* BRM Modulator Register 3 */
#define BMPR4(x) __REG2( IMX_UART1_BASE + 0xcc, ((x) & 1) << 12)	/* BRM Modulator Register 4 */
#define UTS(x)   __REG2( IMX_UART1_BASE + 0xd0, ((x) & 1) << 12)	/* UART Test Register */

/* UART Control Register Bit Fields.*/
#define  URXD_CHARRDY    (1<<15)
#define  URXD_ERR        (1<<14)
#define  URXD_OVRRUN     (1<<13)
#define  URXD_FRMERR     (1<<12)
#define  URXD_BRK        (1<<11)
#define  URXD_PRERR      (1<<10)
#define  UCR1_ADEN       (1<<15) /* Auto dectect interrupt */
#define  UCR1_ADBR       (1<<14) /* Auto detect baud rate */
#define  UCR1_TRDYEN     (1<<13) /* Transmitter ready interrupt enable */
#define  UCR1_IDEN       (1<<12) /* Idle condition interrupt */
#define  UCR1_RRDYEN     (1<<9)	 /* Recv ready interrupt enable */
#define  UCR1_RDMAEN     (1<<8)	 /* Recv ready DMA enable */
#define  UCR1_IREN       (1<<7)	 /* Infrared interface enable */
#define  UCR1_TXMPTYEN   (1<<6)	 /* Transimitter empty interrupt enable */
#define  UCR1_RTSDEN     (1<<5)	 /* RTS delta interrupt enable */
#define  UCR1_SNDBRK     (1<<4)	 /* Send break */
#define  UCR1_TDMAEN     (1<<3)	 /* Transmitter ready DMA enable */
#define  UCR1_UARTCLKEN  (1<<2)	 /* UART clock enabled */
#define  UCR1_DOZE       (1<<1)	 /* Doze */
#define  UCR1_UARTEN     (1<<0)	 /* UART enabled */
#define  UCR2_ESCI	 (1<<15) /* Escape seq interrupt enable */
#define  UCR2_IRTS	 (1<<14) /* Ignore RTS pin */
#define  UCR2_CTSC	 (1<<13) /* CTS pin control */
#define  UCR2_CTS        (1<<12) /* Clear to send */
#define  UCR2_ESCEN      (1<<11) /* Escape enable */
#define  UCR2_PREN       (1<<8) /* Parity enable */
#define  UCR2_PROE       (1<<7) /* Parity odd/even */
#define  UCR2_STPB       (1<<6)	/* Stop */
#define  UCR2_WS         (1<<5)	/* Word size */
#define  UCR2_RTSEN      (1<<4)	/* Request to send interrupt enable */
#define  UCR2_TXEN       (1<<2)	/* Transmitter enabled */
#define  UCR2_RXEN       (1<<1)	/* Receiver enabled */
#define  UCR2_SRST	 (1<<0)	/* SW reset */
#define  UCR3_DTREN	 (1<<13) /* DTR interrupt enable */
#define  UCR3_PARERREN   (1<<12) /* Parity enable */
#define  UCR3_FRAERREN   (1<<11) /* Frame error interrupt enable */
#define  UCR3_DSR        (1<<10) /* Data set ready */
#define  UCR3_DCD        (1<<9)  /* Data carrier detect */
#define  UCR3_RI         (1<<8)  /* Ring indicator */
#define  UCR3_TIMEOUTEN  (1<<7)  /* Timeout interrupt enable */
#define  UCR3_RXDSEN	 (1<<6)  /* Receive status interrupt enable */
#define  UCR3_AIRINTEN   (1<<5)  /* Async IR wake interrupt enable */
#define  UCR3_AWAKEN	 (1<<4)  /* Async wake interrupt enable */
#define  UCR3_REF25	 (1<<3)  /* Ref freq 25 MHz */
#define  UCR3_REF30	 (1<<2)  /* Ref Freq 30 MHz */
#define  UCR3_INVT	 (1<<1)  /* Inverted Infrared transmission */
#define  UCR3_BPEN	 (1<<0)  /* Preset registers enable */
#define  UCR4_CTSTL_32   (32<<10) /* CTS trigger level (32 chars) */
#define  UCR4_INVR	 (1<<9)  /* Inverted infrared reception */
#define  UCR4_ENIRI	 (1<<8)  /* Serial infrared interrupt enable */
#define  UCR4_WKEN	 (1<<7)  /* Wake interrupt enable */
#define  UCR4_REF16	 (1<<6)  /* Ref freq 16 MHz */
#define  UCR4_IRSC	 (1<<5) /* IR special case */
#define  UCR4_TCEN	 (1<<3) /* Transmit complete interrupt enable */
#define  UCR4_BKEN	 (1<<2) /* Break condition interrupt enable */
#define  UCR4_OREN	 (1<<1) /* Receiver overrun interrupt enable */
#define  UCR4_DREN	 (1<<0) /* Recv data ready interrupt enable */
#define  UFCR_RXTL_SHF   0      /* Receiver trigger level shift */
#define  UFCR_RFDIV      (7<<7) /* Reference freq divider mask */
#define  UFCR_TXTL_SHF   10     /* Transmitter trigger level shift */
#define  USR1_PARITYERR  (1<<15) /* Parity error interrupt flag */
#define  USR1_RTSS	 (1<<14) /* RTS pin status */
#define  USR1_TRDY	 (1<<13) /* Transmitter ready interrupt/dma flag */
#define  USR1_RTSD	 (1<<12) /* RTS delta */
#define  USR1_ESCF	 (1<<11) /* Escape seq interrupt flag */
#define  USR1_FRAMERR    (1<<10) /* Frame error interrupt flag */
#define  USR1_RRDY       (1<<9)	/* Receiver ready interrupt/dma flag */
#define  USR1_TIMEOUT    (1<<7)	/* Receive timeout interrupt status */
#define  USR1_RXDS	 (1<<6)	/* Receiver idle interrupt flag */
#define  USR1_AIRINT	 (1<<5)	/* Async IR wake interrupt flag */
#define  USR1_AWAKE	 (1<<4)	/* Aysnc wake interrupt flag */
#define  USR2_ADET	 (1<<15) /* Auto baud rate detect complete */
#define  USR2_TXFE	 (1<<14) /* Transmit buffer FIFO empty */
#define  USR2_DTRF	 (1<<13) /* DTR edge interrupt flag */
#define  USR2_IDLE	 (1<<12) /* Idle condition */
#define  USR2_IRINT	 (1<<8)	/* Serial infrared interrupt flag */
#define  USR2_WAKE	 (1<<7)	/* Wake */
#define  USR2_RTSF	 (1<<4)	/* RTS edge interrupt flag */
#define  USR2_TXDC	 (1<<3)	/* Transmitter complete */
#define  USR2_BRCD	 (1<<2)	/* Break condition */
#define  USR2_ORE        (1<<1)	/* Overrun error */
#define  USR2_RDR        (1<<0)	/* Recv data ready */
#define  UTS_FRCPERR	 (1<<13) /* Force parity error */
#define  UTS_LOOP        (1<<12) /* Loop tx and rx */
#define  UTS_TXEMPTY	 (1<<6)	/* TxFIFO empty */
#define  UTS_RXEMPTY	 (1<<5)	/* RxFIFO empty */
#define  UTS_TXFULL	 (1<<4)	/* TxFIFO full */
#define  UTS_RXFULL	 (1<<3)	/* RxFIFO full */
#define  UTS_SOFTRST	 (1<<0)	/* Software reset */

/* General purpose timers registers */
#define TCTL1   __REG(IMX_TIM1_BASE)
#define TPRER1  __REG(IMX_TIM1_BASE + 0x4)
#define TCMP1   __REG(IMX_TIM1_BASE + 0x8)
#define TCR1    __REG(IMX_TIM1_BASE + 0xc)
#define TCN1    __REG(IMX_TIM1_BASE + 0x10)
#define TSTAT1  __REG(IMX_TIM1_BASE + 0x14)
#define TCTL2   __REG(IMX_TIM2_BASE)
#define TPRER2  __REG(IMX_TIM2_BASE + 0x4)
#define TCMP2   __REG(IMX_TIM2_BASE + 0x8)
#define TCR2    __REG(IMX_TIM2_BASE + 0xc)
#define TCN2    __REG(IMX_TIM2_BASE + 0x10)
#define TSTAT2  __REG(IMX_TIM2_BASE + 0x14)

/* General purpose timers bitfields */
#define TCTL_SWR       (1<<15) /* Software reset */
#define TCTL_FRR       (1<<8)  /* Freerun / restart */
#define TCTL_CAP       (3<<6)  /* Capture Edge */
#define TCTL_OM        (1<<5)  /* output mode */
#define TCTL_IRQEN     (1<<4)  /* interrupt enable */
#define TCTL_CLKSOURCE (7<<1)  /* Clock source */
#define TCTL_TEN       (1)     /* Timer enable */
#define TPRER_PRES     (0xff)  /* Prescale */
#define TSTAT_CAPT     (1<<1)  /* Capture event */
#define TSTAT_COMP     (1)     /* Compare event */

#endif				/* _IMX_REGS_H */