include/configs/MBX860T.h - uboot/prism - Git at Google

  /*
   * A collection of structures, addresses, and values associated with
   * the Motorola 860T MBX board.
   * Copied from the FADS stuff, which was originally copied from the MBX stuff!
   * Magnus Damm added defines for 8xxrom and extended bd_info.
   * Helmut Buchsbaum added bitvalues for BCSRx
   * Rob Taylor coverted it back to MBX
   *
   * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
   */

 /* ------------------------------------------------------------------------- */

 /*
  * board/config.h - configuration options, board specific
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  * (easy to change)
  */
 #include <mpc8xx_irq.h>

 #define CONFIG_MPC860		1
 #define CONFIG_MPC860T		1
 #define CONFIG_MBX		1

 #define CONFIG_8xx_CPUCLOCK	40
 #define CONFIG_8xx_BUSCLOCK	(CONFIG_8xx_CPUCLOCK)
 #define TARGET_SYSTEM_FREQUENCY 40

 #define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
 #undef	CONFIG_8xx_CONS_SMC2
 #define CONFIG_BAUDRATE		9600

 #define MPC8XX_FACT	10				/* Multiply by 10		*/
 #define MPC8XX_XIN	40000000		/* 50 MHz in	*/
 #define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))

 #define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */

 #if 1
 #define CONFIG_8xx_BOOTDELAY	-1	/* autoboot disabled		*/
 #define CONFIG_8xx_TFTP_MODE
 #else
 #define CONFIG_8xx_BOOTDELAY	5	/* autoboot after 5 seconds	*/
 #undef	CONFIG_8xx_TFTP_MODE
 #endif

 #define CONFIG_MISC_INIT_R

 #define CONFIG_DRAM_SPEED	(CONFIG_8xx_BUSCLOCK)	/* MHz		*/
 #define CONFIG_BOOTCOMMAND	"bootm FE020000"	/* autoboot command */
 #define CONFIG_BOOTARGS		" "
 /*
  * Miscellaneous configurable options
  */
 #undef	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
 #define	CONFIG_SYS_PROMPT		":>"		/* Monitor Command Prompt	*/
 #define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
 #define	CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 #define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

 #define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x0800000	/* 4 ... 8 MB in DRAM	*/

 #define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/

 #define	CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks	*/

 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }

 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
  * You should know what you are doing if you make changes here.
  */
 /*-----------------------------------------------------------------------
  * Internal Memory Mapped Register
  */
 #define CONFIG_SYS_IMMR			0xFFA00000
 #define CONFIG_SYS_IMMR_SIZE		((uint)(64 * 1024))
 #define CONFIG_SYS_NVRAM_BASE		0xFA000000 /* NVRAM                          */
 #define CONFIG_SYS_NVRAM_OR		0xffe00000 /* w/o speed dependent flags!!    */
 #define CONFIG_SYS_CSR_BASE		0xFA100000 /* Control/Status Registers       */
 #define CONFIG_SYS_PCIMEM_BASE		0x80000000 /* PCI I/O and Memory Spaces      */
 #define CONFIG_SYS_PCIMEM_OR		0xA0000108
 #define CONFIG_SYS_PCIBRIDGE_BASE	0xFA210000 /* PCI-Bus Bridge Registers       */
 #define CONFIG_SYS_PCIBRIDGE_OR	0xFFFF0108

 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
 #define	CONFIG_SYS_INIT_RAM_END	0x2f00	/* End of used area in DPRAM	*/
 #define	CONFIG_SYS_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 #define	CONFIG_SYS_INIT_VPD_SIZE	256 /* size in bytes reserved for vpd buffer */
 #define CONFIG_SYS_INIT_VPD_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_VPD_SIZE)
 #define	CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_INIT_VPD_OFFSET-8)

 /*-----------------------------------------------------------------------
  * Offset in DPMEM where we keep the VPD data
  */
 #define CONFIG_SYS_DPRAMVPD		(CONFIG_SYS_INIT_VPD_OFFSET - 0x2000)

 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
 #define	CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_FLASH_BASE		0x00000000
 /*0xFE000000*/
 #define CONFIG_SYS_FLASH_SIZE		((uint)(8 * 1024 * 1024))	/* max 8Mbyte */
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
 #define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
 #define CONFIG_SYS_HWINFO_ADDR		(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_SYS_HWINFO_LEN)
 #define	CONFIG_SYS_MALLOC_LEN		(256 << 10)	/* Reserve 256 kB for malloc()	*/

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/

 /*-----------------------------------------------------------------------
  * FLASH organization
  */
 #define CONFIG_SYS_MAX_FLASH_BANKS	4	/* max number of memory banks		*/
 #define CONFIG_SYS_MAX_FLASH_SECT	16	/* max number of sectors on one chip	*/

 #define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

 /*-----------------------------------------------------------------------
  * NVRAM Configuration
  *
  * Note: the MBX is special because there is already a firmware on this
  * board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we
  * access the NVRAM at the offset 0x1000.
  */
 #define CONFIG_ENV_IS_IN_NVRAM	1	/* turn on NVRAM env feature */
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_NVRAM_BASE + 0x1000)
 #define CONFIG_ENV_SIZE		0x1000

 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
 #define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
 #endif

 /*-----------------------------------------------------------------------
  * SYPCR - System Protection Control				11-9
  * SYPCR can only be written once after reset!
  *-----------------------------------------------------------------------
  * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
  */
 #if defined(CONFIG_WATCHDOG)
 #define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
 			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
 #else
 #define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF)
 #endif

 /*-----------------------------------------------------------------------
  * SIUMCR - SIU Module Configuration				11-6
  *-----------------------------------------------------------------------
  * PCMCIA config., multi-function pin tri-state
  */
 #define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC10 | SIUMCR_SEME)

 /*-----------------------------------------------------------------------
  * TBSCR - Time Base Status and Control				11-26
  *-----------------------------------------------------------------------
  * Clear Reference Interrupt Status, Timebase freezing enabled
  */
 #define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)

 /*-----------------------------------------------------------------------
  * PISCR - Periodic Interrupt Status and Control		11-31
  *-----------------------------------------------------------------------
  * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
  */
 #define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF | PISCR_PTE)

 /*-----------------------------------------------------------------------
  * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
  *-----------------------------------------------------------------------
  * Reset PLL lock status sticky bit, timer expired status bit and timer
  * interrupt status bit - leave PLL multiplication factor unchanged !
  */
 #define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)

 /*-----------------------------------------------------------------------
  * SCCR - System Clock and reset Control Register		15-27
  *-----------------------------------------------------------------------
  * Set clock output, timebase and RTC source and divider,
  * power management and some other internal clocks
  */
 #define SCCR_MASK	(SCCR_RTDIV | SCCR_RTSEL)
 #define CONFIG_SYS_SCCR	SCCR_TBS

  /*-----------------------------------------------------------------------
  *
  *-----------------------------------------------------------------------
  *
  */
 #define CONFIG_SYS_DER		0

 /* Because of the way the 860 starts up and assigns CS0 the
 * entire address space, we have to set the memory controller
 * differently.  Normally, you write the option register
 * first, and then enable the chip select by writing the
 * base register.  For CS0, you must write the base register
 * first, followed by the option register.
 */

 /*
  * Init Memory Controller:
  *
  * BR0/1 and OR0/1 (FLASH)
  */
 /* the other CS:s are determined by looking at parameters in BCSRx */


 #define BCSR_ADDR		((uint) 0xFF010000)
 #define BCSR_SIZE		((uint)(64 * 1024))

 #define FLASH_BASE0_PRELIM	0xFE000000	/* FLASH bank #0	*/
 #define FLASH_BASE1_PRELIM	0xFF010000	/* FLASH bank #0	*/

 #define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
 #define CONFIG_SYS_PRELIM_OR_AM	0xFFF00000	/* OR addr mask */

 /* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0	*/
 #define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)

 #define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
 #define CONFIG_SYS_OR0_PRELIM	(0xFF800000 | OR_CSNT_SAM | OR_BI | OR_SCY_3_CLK)   /* 1 Mbyte until detected and only 1 Mbyte is needed*/
 #define CONFIG_SYS_BR0_PRELIM	(0xFE000000 | BR_V )

 /* BCSRx - Board Control and Status Registers */
 #define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
 #define CONFIG_SYS_OR1_PRELIM	0xFFC00000 | OR_ACS_DIV4
 #define CONFIG_SYS_BR1_PRELIM	(0x00000000 | BR_MS_UPMA | BR_V )


 /*
  * Memory Periodic Timer Prescaler
  */

 /* periodic timer for refresh */
 #define CONFIG_SYS_MAMR_PTA		97		/* start with divider for 100 MHz	*/

 /* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit	*/
 #define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
 #define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/

 /* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
 #define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
 #define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/

 /*
  * MAMR settings for SDRAM
  */

 /* 8 column SDRAM */
 #define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
 			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
 			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
 /* 9 column SDRAM */
 #define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
 			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
 			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)

 #define CONFIG_SYS_MAMR		0x13821000
 /*
  * Internal Definitions
  *
  * Boot Flags
  */
 #define	BOOTFLAG_COLD			0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM			0x02		/* Software reboot			*/


 /* values according to the manual */


 #define PCMCIA_MEM_ADDR		((uint)0xff020000)
 #define PCMCIA_MEM_SIZE		((uint)(64 * 1024))

 #define	BCSR0			((uint) (BCSR_ADDR + 00))
 #define	BCSR1			((uint) (BCSR_ADDR + 0x04))
 #define	BCSR2			((uint) (BCSR_ADDR + 0x08))
 #define	BCSR3			((uint) (BCSR_ADDR + 0x0c))
 #define	BCSR4			((uint) (BCSR_ADDR + 0x10))

 /* FADS bitvalues by Helmut Buchsbaum
  * see MPC8xxADS User's Manual for a proper description
  * of the following structures
  */

 #define BCSR0_ERB       ((uint)0x80000000)
 #define BCSR0_IP        ((uint)0x40000000)
 #define BCSR0_BDIS      ((uint)0x10000000)
 #define BCSR0_BPS_MASK  ((uint)0x0C000000)
 #define BCSR0_ISB_MASK  ((uint)0x01800000)
 #define BCSR0_DBGC_MASK ((uint)0x00600000)
 #define BCSR0_DBPC_MASK ((uint)0x00180000)
 #define BCSR0_EBDF_MASK ((uint)0x00060000)

 #define BCSR1_FLASH_EN           ((uint)0x80000000)
 #define BCSR1_DRAM_EN            ((uint)0x40000000)
 #define BCSR1_ETHEN              ((uint)0x20000000)
 #define BCSR1_IRDEN              ((uint)0x10000000)
 #define BCSR1_FLASH_CFG_EN       ((uint)0x08000000)
 #define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
 #define BCSR1_BCSR_EN            ((uint)0x02000000)
 #define BCSR1_RS232EN_1          ((uint)0x01000000)
 #define BCSR1_PCCEN              ((uint)0x00800000)
 #define BCSR1_PCCVCC0            ((uint)0x00400000)
 #define BCSR1_PCCVPP_MASK        ((uint)0x00300000)
 #define BCSR1_DRAM_HALF_WORD     ((uint)0x00080000)
 #define BCSR1_RS232EN_2          ((uint)0x00040000)
 #define BCSR1_SDRAM_EN           ((uint)0x00020000)
 #define BCSR1_PCCVCC1            ((uint)0x00010000)

 #define BCSR2_FLASH_PD_MASK      ((uint)0xF0000000)
 #define BCSR2_DRAM_PD_MASK       ((uint)0x07800000)
 #define BCSR2_DRAM_PD_SHIFT      (23)
 #define BCSR2_EXTTOLI_MASK       ((uint)0x00780000)
 #define BCSR2_DBREVNR_MASK       ((uint)0x00030000)

 #define BCSR3_DBID_MASK          ((ushort)0x3800)
 #define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
 #define BCSR3_BREVNR0            ((ushort)0x0080)
 #define BCSR3_FLASH_PD_MASK      ((ushort)0x0070)
 #define BCSR3_BREVN1             ((ushort)0x0008)
 #define BCSR3_BREVN2_MASK        ((ushort)0x0003)

 #define BCSR4_ETHLOOP            ((uint)0x80000000)
 #define BCSR4_TFPLDL             ((uint)0x40000000)
 #define BCSR4_TPSQEL             ((uint)0x20000000)
 #define BCSR4_SIGNAL_LAMP        ((uint)0x10000000)
 #ifdef CONFIG_MPC823
 #define BCSR4_USB_EN             ((uint)0x08000000)
 #endif /* CONFIG_MPC823 */
 #ifdef CONFIG_MPC860SAR
 #define BCSR4_UTOPIA_EN          ((uint)0x08000000)
 #endif /* CONFIG_MPC860SAR */
 #ifdef CONFIG_MPC860T
 #define BCSR4_FETH_EN            ((uint)0x08000000)
 #endif /* CONFIG_MPC860T */
 #define BCSR4_USB_SPEED          ((uint)0x04000000)
 #define BCSR4_VCCO               ((uint)0x02000000)
 #define BCSR4_VIDEO_ON           ((uint)0x00800000)
 #define BCSR4_VDO_EKT_CLK_EN     ((uint)0x00400000)
 #define BCSR4_VIDEO_RST          ((uint)0x00200000)
 #define BCSR4_MODEM_EN           ((uint)0x00100000)
 #define BCSR4_DATA_VOICE         ((uint)0x00080000)

 #define CONFIG_DRAM_40MHZ		1

 #ifdef CONFIG_MPC860T

 /* Interrupt level assignments.
 */
 #define FEC_INTERRUPT	SIU_LEVEL1	/* FEC interrupt */

 #endif /* CONFIG_MPC860T */

 /* We don't use the 8259.
 */
 #define NR_8259_INTS	0

 #define CONFIG_CMD_NET
 /*
  * MPC8xx CPM Options
  */
 #define CONFIG_SCC_ENET 1
 #define CONFIG_SCC1_ENET 1
 #define CONFIG_FEC_ENET 1
 #undef  CONFIG_CPM_IIC
 #undef  CONFIG_UCODE_PATCH


 #define CONFIG_DISK_SPINUP_TIME 1000000


 /* PCMCIA configuration */

 #define PCMCIA_MAX_SLOTS    2

 #ifdef CONFIG_MPC860
 #define PCMCIA_SLOT_A 1
 #endif

 #endif	/* __CONFIG_H */
	/*
	* A collection of structures, addresses, and values associated with
	* the Motorola 860T MBX board.
	* Copied from the FADS stuff, which was originally copied from the MBX stuff!
	* Magnus Damm added defines for 8xxrom and extended bd_info.
	* Helmut Buchsbaum added bitvalues for BCSRx
	* Rob Taylor coverted it back to MBX
	*
	* Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
	*/

	/* ------------------------------------------------------------------------- */

	/*
	* board/config.h - configuration options, board specific
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	* (easy to change)
	*/
	#include <mpc8xx_irq.h>

	#define CONFIG_MPC860 1
	#define CONFIG_MPC860T 1
	#define CONFIG_MBX 1

	#define CONFIG_8xx_CPUCLOCK 40
	#define CONFIG_8xx_BUSCLOCK (CONFIG_8xx_CPUCLOCK)
	#define TARGET_SYSTEM_FREQUENCY 40

	#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
	#undef CONFIG_8xx_CONS_SMC2
	#define CONFIG_BAUDRATE 9600

	#define MPC8XX_FACT 10 /* Multiply by 10 */
	#define MPC8XX_XIN 40000000 /* 50 MHz in */
	#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))

	#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */

	#if 1
	#define CONFIG_8xx_BOOTDELAY -1 /* autoboot disabled */
	#define CONFIG_8xx_TFTP_MODE
	#else
	#define CONFIG_8xx_BOOTDELAY 5 /* autoboot after 5 seconds */
	#undef CONFIG_8xx_TFTP_MODE
	#endif

	#define CONFIG_MISC_INIT_R

	#define CONFIG_DRAM_SPEED (CONFIG_8xx_BUSCLOCK) /* MHz */
	#define CONFIG_BOOTCOMMAND "bootm FE020000" /* autoboot command */
	#define CONFIG_BOOTARGS " "
	/*
	* Miscellaneous configurable options
	*/
	#undef CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_PROMPT ":>" /* Monitor Command Prompt */
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x0800000 /* 4 ... 8 MB in DRAM */

	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */

	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */

	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }

	/*
	* Low Level Configuration Settings
	* (address mappings, register initial values, etc.)
	* You should know what you are doing if you make changes here.
	*/
	/*-----------------------------------------------------------------------
	* Internal Memory Mapped Register
	*/
	#define CONFIG_SYS_IMMR 0xFFA00000
	#define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024))
	#define CONFIG_SYS_NVRAM_BASE 0xFA000000 /* NVRAM */
	#define CONFIG_SYS_NVRAM_OR 0xffe00000 /* w/o speed dependent flags!! */
	#define CONFIG_SYS_CSR_BASE 0xFA100000 /* Control/Status Registers */
	#define CONFIG_SYS_PCIMEM_BASE 0x80000000 /* PCI I/O and Memory Spaces */
	#define CONFIG_SYS_PCIMEM_OR 0xA0000108
	#define CONFIG_SYS_PCIBRIDGE_BASE 0xFA210000 /* PCI-Bus Bridge Registers */
	#define CONFIG_SYS_PCIBRIDGE_OR 0xFFFF0108

	/*-----------------------------------------------------------------------
	* Definitions for initial stack pointer and data area (in DPRAM)
	*/
	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
	#define CONFIG_SYS_INIT_RAM_END 0x2f00 /* End of used area in DPRAM */
	#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_VPD_SIZE 256 /* size in bytes reserved for vpd buffer */
	#define CONFIG_SYS_INIT_VPD_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_VPD_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_VPD_OFFSET-8)

	/*-----------------------------------------------------------------------
	* Offset in DPMEM where we keep the VPD data
	*/
	#define CONFIG_SYS_DPRAMVPD (CONFIG_SYS_INIT_VPD_OFFSET - 0x2000)

	/*-----------------------------------------------------------------------
	* Start addresses for the final memory configuration
	* (Set up by the startup code)
	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
	*/
	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_FLASH_BASE 0x00000000
	/0xFE000000/
	#define CONFIG_SYS_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
	#define CONFIG_SYS_HWINFO_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_SYS_HWINFO_LEN)
	#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */

	/*-----------------------------------------------------------------------
	* FLASH organization
	*/
	#define CONFIG_SYS_MAX_FLASH_BANKS 4 /* max number of memory banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 16 /* max number of sectors on one chip */

	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */

	/*-----------------------------------------------------------------------
	* NVRAM Configuration
	*
	* Note: the MBX is special because there is already a firmware on this
	* board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we
	* access the NVRAM at the offset 0x1000.
	*/
	#define CONFIG_ENV_IS_IN_NVRAM 1 /* turn on NVRAM env feature */
	#define CONFIG_ENV_ADDR (CONFIG_SYS_NVRAM_BASE + 0x1000)
	#define CONFIG_ENV_SIZE 0x1000

	/*-----------------------------------------------------------------------
	* Cache Configuration
	*/
	#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
	#endif

	/*-----------------------------------------------------------------------
	* SYPCR - System Protection Control 11-9
	* SYPCR can only be written once after reset!
	*-----------------------------------------------------------------------
	* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
	*/
	#if defined(CONFIG_WATCHDOG)
	#define CONFIG_SYS_SYPCR (SYPCR_SWTC \| SYPCR_BMT \| SYPCR_BME \| SYPCR_SWF \| \
	SYPCR_SWE \| SYPCR_SWRI\| SYPCR_SWP)
	#else
	#define CONFIG_SYS_SYPCR (SYPCR_SWTC \| SYPCR_BMT \| SYPCR_BME \| SYPCR_SWF)
	#endif

	/*-----------------------------------------------------------------------
	* SIUMCR - SIU Module Configuration 11-6
	*-----------------------------------------------------------------------
	* PCMCIA config., multi-function pin tri-state
	*/
	#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 \| SIUMCR_DPC \| SIUMCR_MLRC10 \| SIUMCR_SEME)

	/*-----------------------------------------------------------------------
	* TBSCR - Time Base Status and Control 11-26
	*-----------------------------------------------------------------------
	* Clear Reference Interrupt Status, Timebase freezing enabled
	*/
	#define CONFIG_SYS_TBSCR (TBSCR_REFA \| TBSCR_REFB \| TBSCR_TBF)

	/*-----------------------------------------------------------------------
	* PISCR - Periodic Interrupt Status and Control 11-31
	*-----------------------------------------------------------------------
	* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
	*/
	#define CONFIG_SYS_PISCR (PISCR_PS \| PISCR_PITF \| PISCR_PTE)

	/*-----------------------------------------------------------------------
	* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
	*-----------------------------------------------------------------------
	* Reset PLL lock status sticky bit, timer expired status bit and timer
	* interrupt status bit - leave PLL multiplication factor unchanged !
	*/
	#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS \| PLPRCR_TEXPS \| PLPRCR_TMIST)

	/*-----------------------------------------------------------------------
	* SCCR - System Clock and reset Control Register 15-27
	*-----------------------------------------------------------------------
	* Set clock output, timebase and RTC source and divider,
	* power management and some other internal clocks
	*/
	#define SCCR_MASK (SCCR_RTDIV \| SCCR_RTSEL)
	#define CONFIG_SYS_SCCR SCCR_TBS

	/*-----------------------------------------------------------------------
	*
	*-----------------------------------------------------------------------
	*
	*/
	#define CONFIG_SYS_DER 0

	/* Because of the way the 860 starts up and assigns CS0 the
	* entire address space, we have to set the memory controller
	* differently. Normally, you write the option register
	* first, and then enable the chip select by writing the
	* base register. For CS0, you must write the base register
	* first, followed by the option register.
	*/

	/*
	* Init Memory Controller:
	*
	* BR0/1 and OR0/1 (FLASH)
	*/
	/* the other CS:s are determined by looking at parameters in BCSRx */


	#define BCSR_ADDR ((uint) 0xFF010000)
	#define BCSR_SIZE ((uint)(64 * 1024))

	#define FLASH_BASE0_PRELIM 0xFE000000 /* FLASH bank #0 */
	#define FLASH_BASE1_PRELIM 0xFF010000 /* FLASH bank #0 */

	#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
	#define CONFIG_SYS_PRELIM_OR_AM 0xFFF00000 /* OR addr mask */

	/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
	#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM \| OR_ACS_DIV4 \| OR_BI \| OR_SCY_3_CLK \| OR_TRLX)

	#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM \| CONFIG_SYS_OR_TIMING_FLASH)
	#define CONFIG_SYS_OR0_PRELIM (0xFF800000 \| OR_CSNT_SAM \| OR_BI \| OR_SCY_3_CLK) /* 1 Mbyte until detected and only 1 Mbyte is needed*/
	#define CONFIG_SYS_BR0_PRELIM (0xFE000000 \| BR_V )

	/* BCSRx - Board Control and Status Registers */
	#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
	#define CONFIG_SYS_OR1_PRELIM 0xFFC00000 \| OR_ACS_DIV4
	#define CONFIG_SYS_BR1_PRELIM (0x00000000 \| BR_MS_UPMA \| BR_V )


	/*
	* Memory Periodic Timer Prescaler
	*/

	/* periodic timer for refresh */
	#define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */

	/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
	#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
	#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */

	/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
	#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
	#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */

	/*
	* MAMR settings for SDRAM
	*/

	/* 8 column SDRAM */
	#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) \| MAMR_PTAE \| \
	MAMR_AMA_TYPE_0 \| MAMR_DSA_1_CYCL \| MAMR_G0CLA_A11 \| \
	MAMR_RLFA_1X \| MAMR_WLFA_1X \| MAMR_TLFA_4X)
	/* 9 column SDRAM */
	#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) \| MAMR_PTAE \| \
	MAMR_AMA_TYPE_1 \| MAMR_DSA_1_CYCL \| MAMR_G0CLA_A10 \| \
	MAMR_RLFA_1X \| MAMR_WLFA_1X \| MAMR_TLFA_4X)

	#define CONFIG_SYS_MAMR 0x13821000
	/*
	* Internal Definitions
	*
	* Boot Flags
	*/
	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
	#define BOOTFLAG_WARM 0x02 /* Software reboot */


	/* values according to the manual */


	#define PCMCIA_MEM_ADDR ((uint)0xff020000)
	#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))

	#define BCSR0 ((uint) (BCSR_ADDR + 00))
	#define BCSR1 ((uint) (BCSR_ADDR + 0x04))
	#define BCSR2 ((uint) (BCSR_ADDR + 0x08))
	#define BCSR3 ((uint) (BCSR_ADDR + 0x0c))
	#define BCSR4 ((uint) (BCSR_ADDR + 0x10))

	/* FADS bitvalues by Helmut Buchsbaum
	* see MPC8xxADS User's Manual for a proper description
	* of the following structures
	*/

	#define BCSR0_ERB ((uint)0x80000000)
	#define BCSR0_IP ((uint)0x40000000)
	#define BCSR0_BDIS ((uint)0x10000000)
	#define BCSR0_BPS_MASK ((uint)0x0C000000)
	#define BCSR0_ISB_MASK ((uint)0x01800000)
	#define BCSR0_DBGC_MASK ((uint)0x00600000)
	#define BCSR0_DBPC_MASK ((uint)0x00180000)
	#define BCSR0_EBDF_MASK ((uint)0x00060000)

	#define BCSR1_FLASH_EN ((uint)0x80000000)
	#define BCSR1_DRAM_EN ((uint)0x40000000)
	#define BCSR1_ETHEN ((uint)0x20000000)
	#define BCSR1_IRDEN ((uint)0x10000000)
	#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
	#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
	#define BCSR1_BCSR_EN ((uint)0x02000000)
	#define BCSR1_RS232EN_1 ((uint)0x01000000)
	#define BCSR1_PCCEN ((uint)0x00800000)
	#define BCSR1_PCCVCC0 ((uint)0x00400000)
	#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
	#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
	#define BCSR1_RS232EN_2 ((uint)0x00040000)
	#define BCSR1_SDRAM_EN ((uint)0x00020000)
	#define BCSR1_PCCVCC1 ((uint)0x00010000)

	#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
	#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
	#define BCSR2_DRAM_PD_SHIFT (23)
	#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
	#define BCSR2_DBREVNR_MASK ((uint)0x00030000)

	#define BCSR3_DBID_MASK ((ushort)0x3800)
	#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
	#define BCSR3_BREVNR0 ((ushort)0x0080)
	#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
	#define BCSR3_BREVN1 ((ushort)0x0008)
	#define BCSR3_BREVN2_MASK ((ushort)0x0003)

	#define BCSR4_ETHLOOP ((uint)0x80000000)
	#define BCSR4_TFPLDL ((uint)0x40000000)
	#define BCSR4_TPSQEL ((uint)0x20000000)
	#define BCSR4_SIGNAL_LAMP ((uint)0x10000000)
	#ifdef CONFIG_MPC823
	#define BCSR4_USB_EN ((uint)0x08000000)
	#endif /* CONFIG_MPC823 */
	#ifdef CONFIG_MPC860SAR
	#define BCSR4_UTOPIA_EN ((uint)0x08000000)
	#endif /* CONFIG_MPC860SAR */
	#ifdef CONFIG_MPC860T
	#define BCSR4_FETH_EN ((uint)0x08000000)
	#endif /* CONFIG_MPC860T */
	#define BCSR4_USB_SPEED ((uint)0x04000000)
	#define BCSR4_VCCO ((uint)0x02000000)
	#define BCSR4_VIDEO_ON ((uint)0x00800000)
	#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000)
	#define BCSR4_VIDEO_RST ((uint)0x00200000)
	#define BCSR4_MODEM_EN ((uint)0x00100000)
	#define BCSR4_DATA_VOICE ((uint)0x00080000)

	#define CONFIG_DRAM_40MHZ 1

	#ifdef CONFIG_MPC860T

	/* Interrupt level assignments.
	*/
	#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */

	#endif /* CONFIG_MPC860T */

	/* We don't use the 8259.
	*/
	#define NR_8259_INTS 0

	#define CONFIG_CMD_NET
	/*
	* MPC8xx CPM Options
	*/
	#define CONFIG_SCC_ENET 1
	#define CONFIG_SCC1_ENET 1
	#define CONFIG_FEC_ENET 1
	#undef CONFIG_CPM_IIC
	#undef CONFIG_UCODE_PATCH


	#define CONFIG_DISK_SPINUP_TIME 1000000


	/* PCMCIA configuration */

	#define PCMCIA_MAX_SLOTS 2

	#ifdef CONFIG_MPC860
	#define PCMCIA_SLOT_A 1
	#endif

	#endif /* __CONFIG_H */