Properly inverted GLFT110 Output Enable bits.
Updated GLT300 Ouput Enable bits to match the kernel settings.
Change-Id: I5d22a7754006d3c74e27716a42551f396b5413cf
diff --git a/board/mv_feroceon/mv_kw2/kw2_family/boardEnv/mvBoardEnvSpec.h b/board/mv_feroceon/mv_kw2/kw2_family/boardEnv/mvBoardEnvSpec.h
index a12ad38..d317712 100644
--- a/board/mv_feroceon/mv_kw2/kw2_family/boardEnv/mvBoardEnvSpec.h
+++ b/board/mv_feroceon/mv_kw2/kw2_family/boardEnv/mvBoardEnvSpec.h
@@ -537,6 +537,9 @@
/***************************************************************************
** GFLT110
****************************************************************************/
+/*spreadheet on GPIO settings:
+ https://goto.google.com/gflt110-gpio-config
+*/
#define GFLT110_MPP0_7 0x22222220
#define GFLT110_MPP8_15 0x00000002
#define GFLT110_MPP16_23 0x00400000
@@ -562,23 +565,29 @@
29 XVR_SD (in)
33 TX_Fault/TX_indication
37 TX_PD
-
-
*/
-#define GFLT110_GPP_OUT_ENA_LOW (BIT0 | BIT14 | BIT15 | BIT16 | BIT17 | BIT18 | BIT19 | BIT22 | BIT23 | BIT24 | BIT27| BIT28 | BIT30 | BIT31)
-#define GFLT110_GPP_OUT_ENA_MID (BIT0 | BIT3 | BIT4)
+
+
+// default all ones-inputs, invert for outputs
+#define GFLT110_GPP_OUT_ENA_LOW (~(BIT12 | BIT13 | BIT20))
+#define GFLT110_GPP_OUT_ENA_MID (~(BIT5))
+
// BIT12 turns the LED blue.
// BIT13 turns the LED red.
#define GFLT110_GPP_OUT_VAL_LOW BIT13
#define GFLT110_GPP_OUT_VAL_MID 0x0
-#define GFLT110_GPP_POL_LOW (BIT23)
+#define GFLT110_GPP_POL_LOW 0x0
#define GFLT110_GPP_POL_MID 0x0
/***************************************************************************
** GFLT300
****************************************************************************/
+/*spreadheet on GPIO settings:
+ https://goto.google.com/gflt300-gpio-config
+*/
+
#define GFLT300_MPP0_7 0x22222220
#define GFLT300_MPP8_15 0x05000002
#define GFLT300_MPP16_23 0x00000000
@@ -586,62 +595,14 @@
#define GFLT300_MPP32_37 0x00000004
-/* GPPs
- MUX GPIO
- DIR
- 0 NC 0 -
- 1 SPI0_MOSI (out) 2
- 2 SPI0_SCK (out) 2
- 3 SPI0_CSn[0] (out) 2
- 4 SPI0_MISO (in) 2
- 5 I2C0_SDA (inout) 2
- 6 I2C0_SCK (inout) 2
- 7 UA0_TXD (out) 2
-
- 8 UA0_RXD (in) 2
- 9 PON_LED_BLUE (out) 0 out 1
-10 PON_LED_RED (out) 0 out 0
-11 NC 0 -
-12 NC 0 -
-13 BOARD_VER[0] (in) 0 in
-14 GE_LINK_LED (out) 5
-15 BOARD_VER[1](in) 0 in
-
-16 0 -
-17 SW_RESET (in) 0 in
-18 BOARD_VER[2] (in) 0 in
-19 NC 0 -
-20 NC 0 -
-21 POS_TX_DIS (out) 0 out 0
-22 NC 0 -
-23 NC 0 -
-
-24 PTP_TRIG_GEN(out) 4
-25 PTP_EVENT_REQ(in) 4
-26 GE_DATA_LED (out) 5
-27 PTP_CLK_IN (in) 4
-28 SPI_WP_L(out)(in for safety) 0 in
-29 PON_LOS(in) 0 in
-30 DOLOS_DETECT_L 0 in
-31 UART1_TX(out) 4
-
-32 UART1_RX(in) 4
-33 ?NC DYING_GASP 0
-34 PU 0 -
-35 PD 0 -
-36 PON_RX_PMON(in) 0 in
-37 PON_PWR_EN(out) 0 out 1
-
-*/
-
-
-#define GFLT300_GPP_OUT_ENA_LOW (BIT13 | BIT15 | BIT17 | BIT18 | BIT28 | BIT29 | BIT30)
-#define GFLT300_GPP_OUT_ENA_MID (BIT4)
+// default all ones-inputs, invert for outputs
+#define GFLT300_GPP_OUT_ENA_LOW (~(BIT9 | BIT10 | BIT21))
+#define GFLT300_GPP_OUT_ENA_MID (~(BIT5))
// BIT09 turns the LED blue.
// BIT10 turns the LED red.
-#define GFLT300_GPP_OUT_VAL_LOW (BIT9)
-#define GFLT300_GPP_OUT_VAL_MID 0x0
+#define GFLT300_GPP_OUT_VAL_LOW (BIT9 | BIT21)
+#define GFLT300_GPP_OUT_VAL_MID (0)
#define GFLT300_GPP_POL_LOW 0x0
#define GFLT300_GPP_POL_MID 0x0
