| /* |
| * (C) Copyright 2003 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * modified for TOP5200-series by Reinhard Meyer, www.emk-elektronik.de |
| * |
| * TOP5200 differences from IceCube: |
| * 1 FLASH Bank for one Chip only, up to 64 MB in 16 MB Banks |
| * bank switch controlled by TIMER_6(LSB) and TIMER_7(MSB) Pins |
| * 1 SDRAM/DDRAM Bank up to 256 MB |
| * local VPD I2C Bus is software driven and uses |
| * GPIO_WKUP_6 for SDA, GPIO_WKUP_7 for SCL |
| * FLASH is re-located at 0xff000000 |
| * Internal regs are at 0xf0000000 |
| * Reset jumps to 0x00000100 |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| #define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ |
| #define CONFIG_MPC5200 1 /* More exactly a MPC5200 */ |
| #define CONFIG_TOP5200 1 /* ... on TOP5200 board - we need this for FEC.C */ |
| |
| /* |
| * allowed and functional CONFIG_SYS_TEXT_BASE values: |
| * 0xff000000 low boot at 0x00000100 (default board setting) |
| * 0xfff00000 high boot at 0xfff00100 (board needs modification) |
| * 0x00100000 RAM load and test |
| */ |
| #define CONFIG_SYS_TEXT_BASE 0xff000000 |
| |
| #define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ |
| |
| #define CONFIG_HIGH_BATS 1 /* High BATs supported */ |
| |
| /* |
| * Serial console configuration |
| */ |
| #define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ |
| #define CONFIG_BAUDRATE 9600 /* ... at 9600 bps */ |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } |
| |
| |
| #if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200) |
| /* |
| * PCI Mapping: |
| * 0x40000000 - 0x4fffffff - PCI Memory |
| * 0x50000000 - 0x50ffffff - PCI IO Space |
| */ |
| # define CONFIG_PCI 1 |
| # define CONFIG_PCI_PNP 1 |
| # define CONFIG_PCI_SCAN_SHOW 1 |
| # define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 |
| |
| # define CONFIG_PCI_MEM_BUS 0x40000000 |
| # define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS |
| # define CONFIG_PCI_MEM_SIZE 0x10000000 |
| |
| # define CONFIG_PCI_IO_BUS 0x50000000 |
| # define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS |
| # define CONFIG_PCI_IO_SIZE 0x01000000 |
| |
| #endif |
| |
| /* USB */ |
| #if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200) |
| |
| # define CONFIG_USB_OHCI |
| # define CONFIG_USB_CLOCK 0x0001bbbb |
| # if defined (CONFIG_EVAL5200) |
| # define CONFIG_USB_CONFIG 0x00005100 |
| # else |
| # define CONFIG_USB_CONFIG 0x00001000 |
| # endif |
| # define CONFIG_DOS_PARTITION |
| # define CONFIG_USB_STORAGE |
| |
| #endif |
| |
| /* IDE */ |
| #if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200) |
| # define CONFIG_DOS_PARTITION |
| #endif |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_BEDBUG |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_EEPROM |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_IMMAP |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_REGINFO |
| |
| #if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200) |
| #define CONFIG_CMD_FAT |
| #define CONFIG_CMD_IDE |
| #define CONFIG_CMD_USB |
| #define CONFIG_CMD_PCI |
| #endif |
| |
| |
| /* |
| * MUST be low boot - HIGHBOOT is not supported anymore |
| */ |
| #if (CONFIG_SYS_TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */ |
| # define CONFIG_SYS_LOWBOOT 1 |
| # define CONFIG_SYS_LOWBOOT16 1 |
| #else |
| # error "CONFIG_SYS_TEXT_BASE must be 0xff000000" |
| #endif |
| |
| /* |
| * Autobooting |
| */ |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ |
| |
| #define CONFIG_PREBOOT "echo;" \ |
| "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ |
| "echo" |
| |
| #undef CONFIG_BOOTARGS |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=${serverip}:${rootpath}\0" \ |
| "ramargs=setenv bootargs root=/dev/ram rw\0" \ |
| "addip=setenv bootargs ${bootargs} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ |
| ":${hostname}:${netdev}:off panic=1\0" \ |
| "flash_nfs=run nfsargs addip;" \ |
| "bootm ${kernel_addr}\0" \ |
| "flash_self=run ramargs addip;" \ |
| "bootm ${kernel_addr} ${ramdisk_addr}\0" \ |
| "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ |
| "rootpath=/opt/eldk/ppc_82xx\0" \ |
| "bootfile=/tftpboot/MPC5200/uImage\0" \ |
| "" |
| |
| #define CONFIG_BOOTCOMMAND "run flash_self" |
| |
| /* |
| * IPB Bus clocking configuration. |
| */ |
| #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ |
| |
| /* |
| * I2C configuration |
| */ |
| /* |
| * EEPROM configuration |
| */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 |
| |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 |
| #define CONFIG_SYS_EEPROM_SIZE 0x2000 |
| |
| #define CONFIG_ENV_OVERWRITE |
| #define CONFIG_MISC_INIT_R |
| |
| #undef CONFIG_HARD_I2C /* I2C with hardware support */ |
| #define CONFIG_SOFT_I2C 1 /* I2C with softwate support */ |
| |
| #if defined (CONFIG_SOFT_I2C) |
| # define SDA0 0x40 |
| # define SCL0 0x80 |
| # define GPIOE0 *((volatile uchar*)(CONFIG_SYS_MBAR+0x0c00)) |
| # define DDR0 *((volatile uchar*)(CONFIG_SYS_MBAR+0x0c08)) |
| # define DVO0 *((volatile uchar*)(CONFIG_SYS_MBAR+0x0c0c)) |
| # define DVI0 *((volatile uchar*)(CONFIG_SYS_MBAR+0x0c20)) |
| # define ODE0 *((volatile uchar*)(CONFIG_SYS_MBAR+0x0c04)) |
| # define I2C_INIT {GPIOE0|=(SDA0|SCL0);ODE0|=(SDA0|SCL0);DVO0|=(SDA0|SCL0);DDR0|=(SDA0|SCL0);} |
| # define I2C_READ ((DVI0&SDA0)?1:0) |
| # define I2C_SDA(x) {if(x)DVO0|=SDA0;else DVO0&=~SDA0;} |
| # define I2C_SCL(x) {if(x)DVO0|=SCL0;else DVO0&=~SCL0;} |
| # define I2C_DELAY {udelay(5);} |
| # define I2C_ACTIVE {DDR0|=SDA0;} |
| # define I2C_TRISTATE {DDR0&=~SDA0;} |
| # define CONFIG_SYS_I2C_SPEED 100000 |
| # define CONFIG_SYS_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 |
| #define CONFIG_SYS_I2C_FACT_ADDR 0x57 |
| #endif |
| |
| #if defined (CONFIG_HARD_I2C) |
| # define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ |
| # define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ |
| # define CONFIG_SYS_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 |
| #define CONFIG_SYS_I2C_FACT_ADDR 0x54 |
| #endif |
| |
| /* |
| * Flash configuration, expect one 16 Megabyte Bank at most |
| */ |
| #define CONFIG_SYS_FLASH_BASE 0xff000000 |
| #define CONFIG_SYS_FLASH_SIZE 0x01000000 |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0) |
| |
| #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ |
| |
| #undef CONFIG_FLASH_16BIT /* Flash is 8-bit */ |
| |
| /* |
| * DRAM configuration - will be read from VPD later... TODO! |
| */ |
| #if 0 |
| /* 2x MT48LC16M16A2 - 7.0 ns SDRAMS = 64 MegaBytes Total */ |
| #define CONFIG_SYS_DRAM_DDR 0 |
| #define CONFIG_SYS_DRAM_EMODE 0 |
| #define CONFIG_SYS_DRAM_MODE 0x008D |
| #define CONFIG_SYS_DRAM_CONTROL 0x514F0000 |
| #define CONFIG_SYS_DRAM_CONFIG1 0xC2233A00 |
| #define CONFIG_SYS_DRAM_CONFIG2 0x88B70004 |
| #define CONFIG_SYS_DRAM_TAP_DEL 0x08 |
| #define CONFIG_SYS_DRAM_RAM_SIZE 0x19 |
| #endif |
| #if 1 |
| /* 2x MT48LC16M16A2 - 7.5 ns SDRAMS = 64 MegaBytes Total */ |
| #define CONFIG_SYS_DRAM_DDR 0 |
| #define CONFIG_SYS_DRAM_EMODE 0 |
| #define CONFIG_SYS_DRAM_MODE 0x00CD |
| #define CONFIG_SYS_DRAM_CONTROL 0x514F0000 |
| #define CONFIG_SYS_DRAM_CONFIG1 0xD2333A00 |
| #define CONFIG_SYS_DRAM_CONFIG2 0x8AD70004 |
| #define CONFIG_SYS_DRAM_TAP_DEL 0x08 |
| #define CONFIG_SYS_DRAM_RAM_SIZE 0x19 |
| #endif |
| |
| /* |
| * Environment settings |
| */ |
| #define CONFIG_ENV_IS_IN_EEPROM 1 /* turn on EEPROM env feature */ |
| #define CONFIG_ENV_OFFSET 0x1000 |
| #define CONFIG_ENV_SIZE 0x0700 |
| |
| /* |
| * VPD settings |
| */ |
| #define CONFIG_SYS_FACT_OFFSET 0x1800 |
| #define CONFIG_SYS_FACT_SIZE 0x0800 |
| |
| /* |
| * Memory map |
| * |
| * Warning!!! with the current BestComm Task, MBAR MUST BE set to 0xf0000000 |
| */ |
| #define CONFIG_SYS_MBAR 0xf0000000 /* DO NOT CHANGE this */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_DEFAULT_MBAR 0x80000000 |
| |
| /* Use SRAM until RAM will be available */ |
| #define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM |
| #define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */ |
| |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) |
| # define CONFIG_SYS_RAMBOOT 1 |
| #endif |
| |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ |
| #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /* |
| * Ethernet configuration |
| */ |
| #define CONFIG_MPC5xxx_FEC 1 |
| #define CONFIG_MPC5xxx_FEC_MII10 /* Workaround for FEC 100Mbit problem */ |
| #define CONFIG_PHY_ADDR 0x1f |
| #define CONFIG_PHY_TYPE 0x79c874 |
| /* |
| * GPIO configuration: |
| * PSC1,2,3 predefined as UART |
| * PCI disabled |
| * Ethernet 100 with MD |
| */ |
| #define CONFIG_SYS_GPS_PORT_CONFIG 0x00058044 |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| #if defined(CONFIG_CMD_KGDB) |
| # define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| # define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x01f00000 /* 1 ... 31 MB in DRAM */ |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */ |
| |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| #define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ |
| #if defined(CONFIG_CMD_KGDB) |
| # define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ |
| #endif |
| |
| |
| #ifdef CONFIG_EVAL5200 /* M48T08 is available with the Evaluation board only */ |
| #define CONFIG_RTC_MK48T59 1 /* use M48T08 on EVAL5200 */ |
| #define RTC(reg) (0xf0010000+reg) |
| /* setup CS2 for M48T08. Must MAP 64kB */ |
| #define CONFIG_SYS_CS2_START RTC(0) |
| #define CONFIG_SYS_CS2_SIZE 0x10000 |
| /* setup CS2 configuration register: */ |
| /* WaitP = 0, WaitX = 4, MX=0, AL=1, AA=1, CE=1 */ |
| /* AS=2, DS=0, Bank=0, WTyp=0, WS=0, RS=0, WO=0, RO=0 */ |
| #define CONFIG_SYS_CS2_CFG 0x00047800 |
| #else |
| #define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ |
| #endif |
| |
| /* |
| * Various low-level settings |
| */ |
| #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI |
| #define CONFIG_SYS_HID0_FINAL HID0_ICE |
| |
| #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE |
| #define CONFIG_SYS_BOOTCS_CFG 0x00047801 |
| #define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE |
| |
| #define CONFIG_SYS_CS_BURST 0x00000000 |
| #define CONFIG_SYS_CS_DEADCYCLE 0x33333333 |
| |
| #define CONFIG_SYS_RESET_ADDRESS 0x7f000000 |
| |
| /*----------------------------------------------------------------------- |
| * IDE/ATA stuff Supports IDE harddisk |
| *----------------------------------------------------------------------- |
| */ |
| |
| #undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ |
| |
| #undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ |
| #undef CONFIG_IDE_LED /* LED for ide not supported */ |
| |
| #define CONFIG_IDE_RESET 1 |
| #define CONFIG_IDE_PREINIT |
| |
| #define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ |
| #define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ |
| |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 |
| |
| #define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA |
| |
| /* Offset for data I/O */ |
| #define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) |
| |
| /* Offset for normal register accesses */ |
| #define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) |
| |
| /* Offset for alternate registers */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET (0x005c) |
| |
| /* Interval between registers */ |
| #define CONFIG_SYS_ATA_STRIDE 4 |
| |
| #endif /* __CONFIG_H */ |
